Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Comparison of CIGS solar cells made with different structures and fabrication techniques

Cu(In, Ga)Se2 (CIGS)-based solar cells from six fabricators were characterized and compared. The devices had differing substrates, absorber deposition processes, buffer materials, and contact materials. The effective bandgaps of devices varied from 1.05 to 1.22 eV, with the lowest optical bandgaps occurring in those with metal-precursor absorber processes. Devices with Zn(O, S) or thin CdS buffers had quantum efficiencies above 90% down to 400 nm. Most voltages were 250-300 mV below the Shockley-Queisser limit for their bandgap. Electroluminescence intensity tracked well with the respective voltage deficits. Fill factor (FF) was as high as 95% of the maximum for each device's respective current and voltage, with higher FF corresponding to lower diode quality factors (~1.3). An in-depth analysis of FF losses determined that diode quality reflected in the quality factor, voltage-dependent photocurrent, and, to a lesser extent, the parasitic resistances are the limiting factors. As a result, different absorber processes and device structures led to a range of electrical and physical characteristics, yet this investigation showed that multiple fabrication pathways could lead to high-quality and high-efficiency solar cells.

14 SOLAR ENERGY↗

Directed self-assembly of block copolymers for high-precision patterning in the era of extreme ultraviolet lithography

Extreme ultraviolet (EUV) lithography enables unprecedented resolution in semiconductor patterning but faces critical challenges in developing resist materials that achieve high-precision at economically viable throughput. Directed self-assembly (DSA) of block copolymers (BCPs) offers a promising solution for pattern rectification by leveraging thermodynamically determined domain structures to decouple BCP pattern quality from the imperfect original lithographic pattern. This prospective presents an overview of recent progress on the EUV + DSA strategy, covering advances in BCP material design, processing, metrology, and pattern transfer. We highlight recent advances in high-χ BCPs with perpendicular orientation and domain spacings compatible with EUV dimensions, leveraging A-b-(B-r-C) architectures. We also discuss progress in chemical pre-pattern fabrication using both positive- and negative tone resists, along with processing strategies to minimize defects and roughness based on BCP thermodynamics and assembly kinetics. We further examine metrology platforms for characterizing the thermodynamics of BCP materials and quantifying the size and shape of BCP domains. Lastly, we review pattern transfer strategies for generating functional inorganic masks suitable for semiconductor manufacturing. Together, these advances highlight the potential of DSA to complement EUV lithography, offering a pathway to address critical challenges in achieving high-precision patterning for the semiconductor industry.

Lee, Kyunghyeon [Univ. of Chicago, IL (United Stat↗

Simulation of Infrared Laser Heating of Silica Using Heat Conduction and Multifrequency Radiation Diffusion Equations Adapted for Homogeneous Refractive Lossy Media

Localized, transient heating of materials using micro-scale, highly absorbing laser light has been used in many industries to anneal, melt and ablate material with high precision. Accurate modeling of the relative contributions of conductive, convective and radiative losses as a function of laser parameters is essential to optimizing micro-scale laser processing of materials. In bulk semi-transparent materials such as silicate glass melts, radiation transport is known to play a significantly larger role as the temperature increases. Conventionally, radiation is treated in the frequency-averaged diffusive limit (Rosseland approximation). However, the role and proper treatment of radiative processes under rapidly heated, high thermal gradient conditions, often created through laser-matter interactions, is at present not clear. Starting from the radiation transport equation for homogeneous, refractive lossy media, they derive the corresponding time-dependent multi-frequency diffusion equations. Zeroth and first moments of the transport equation couple the energy density, flux and pressure tensor. The system is closed by neglecting the temporal derivative of the flux and replacing the pressure tensor by its diagonal analogue. The radiation equations are coupled to a diffusion equation for the matter temperature. They are interested in modeling infrared laser heating of silica over sub-millimeter length scales, and at possibly rapid rates. Hence, in contrast to related work, they retain the temporal derivative of the radiation field. They derive boundary conditions at a planar air-silica interface taking account of reflectivities obtained from the Fresnel relations that include absorption. The effect of a temperature-dependent absorption index is explored through construction of a multi-phonon dielectric function that includes mode dispersion. The spectral dimension is discretized into a finite number of intervals yielding a system of multigroup diffusion equations. Simulations are presented. To demonstrate the bulk heat loss due to radiation and the effect of the radiation's temporal derivative, they model cooling of a silica slab, initially at 2500 K, for 10 s. Retaining the derivative enables correctly modeling the loss of photons initially present in the slab. Other simulations model irradiating silica discs (of approximately 5 mm radii and thickness) with a CO2 laser: {lambda} = 10.59 and 4.6 um, Gaussian profile, r{sub 0} = 0.5 mm for 1/e decay. By surrounding the disks in room-temperature air, they make use of the boundary conditions described above.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Chemical and Morphological Control of Interfacial Self-Doping for Efficient Organic Electronics

Solution-based processing of materials for electrical doping of organic semiconductor interfaces is attractive for boosting the efficiency of organic electronic devices with multilayer structures. In order to simplify this process, self-doping perylene diimide (PDI)-based ionene polymers are synthesized, in which the semiconductor PDI components are embedded together with electrolyte dopants in the polymer backbone. Functionality contained within the PDI monomers suppresses their aggregation, affording self-doping interlayers with controllable thickness when processed from solution into organic photovoltaic devices (OPVs). Optimal results for interfacial self-doping lead to increased power conversion efficiencies (PCEs) of the fullerene-based OPVs, from 2.62% to 10.64%, and of the nonfullerene-based OPVs, from 3.34% to 10.59%. These PDI–ionene interlayers enable chemical and morphological control of interfacial doping and conductivity, demonstrating that the conductive channels are crucial for charge transport in doped organic semiconductor films. Using these novel interlayers with efficient doping and high conductivity, both fullerene- and nonfullerene-based OPVs are achieved with PCEs exceeding 9% over interlayer thicknesses ranging from ≈3 to 40 nm.

36 MATERIALS SCIENCE↗

Formation of uranium oxy-carbide and uranium carbide via conversion of polymer covered uranium dioxide by laser-based thermal processing

Conventional formation of carbonaceous uranium compounds requires bulk processing using furnace-based approaches. Here, a methodology employing polymer covered uranium dioxide and laser-based heating is explored to enable rapid, localized formation of carbonaceous uranium compounds. Specifically, heating of poly(methyl methacrylate) covered uranium dioxide powder to high temperatures using laser irradiation in argon and methane gaseous environments was investigated. Decomposition of material and reactions induced by laser irradiation were probed in situ by residual gas analysis using a benchtop mass spectrometer. In this study, to determine the effect on the resultant material phase, three different process parameters were varied: gaseous atmosphere, laser power, and laser irradiation time. Material processed under varying conditions was analyzed using powder X-ray diffraction and scanning electron microscopy. This work realized the conversion of uranium dioxide into uranium oxy-carbide(s) and uranium carbide(s) phases, at over 60 wt.%, via the polymer surface application and laser-based thermal decomposition methodology.

36 MATERIALS SCIENCE↗

Towards the holistic design of alloys with large language models

Large language models are very effective at solving general tasks, but can also be useful in materials design and extracting and using information from the scientific literature and unstructured corpora. For instance, in the domain of alloy design and manufacturing, they can expedite the materials design process and enable the inclusion of holistic criteria.

36 MATERIALS SCIENCE↗

Composite laminate failure parameter optimization through four-point flexure experimentation and analysis

Fiber-reinforced composite materials offer light-weight solutions to many structural challenges. In the development of high-performance composite structures, a thorough understanding is required of the composite materials themselves as well as methods for the analysis and failure prediction of the relevant composite structures. However, the mechanical properties required for the complete constitutive definition of a composite material can be difficult to determine through experimentation. Therefore, efficient methods are necessary that can be used to determine which properties are relevant to the analysis of a specific structure and to establish a structure's response to a material parameter that can only be defined through estimation. The objectives of this paper deal with demonstrating the potential value of sensitivity and uncertainty quantification techniques during the failure analysis of loaded composite structures; and the proposed methods are applied to the simulation of the four-point flexural characterization of a carbon fiber composite material. Utilizing a recently implemented, phenomenological orthotropic material model that is capable of predicting progressive composite damage and failure, a sensitivity analysis is completed to establish which material parameters are truly relevant to a simulation's outcome. Then, a parameter study is completed to determine the effect of the relevant material properties' expected variations on the simulated four-point flexural behavior as well as to determine the value of an unknown material property. This process demonstrates the ability to formulate accurate predictions in the absence of a rigorous material characterization effort. Finally, the presented results indicate that a sensitivity analysis and parameter study can be used to streamline the material definition process as the described flexural characterization was used for model validation.

36 MATERIALS SCIENCE↗

Lightweight Metal Stamping Optimization Enabled by Artificial Intelligence

Successfully manufacturing an automotive body structure made via the sheet metal stamping process depends upon simultaneous consideration of component design, tooling design, stamping process control, and material properties. In many cases, introducing lightweight sheet materials (e.g., aluminum alloys, magnesium alloys, advanced high strength steels) holds the potential to significantly reduce vehicle weight, but challenges the stamping process by introducing materials with inherently less ductility. Successful and repeatable applications require co-developing the stamping process controls with the varying material properties, including formability. During the stamping process, as soon as the forming limit of the sheet is exceeded, the material shows localized necking which quickly leads to splits. Controlling process variability to avoid these material splits will enable deployment of less formable, lighter, and stronger materials for stamped automotive components. A typical optimization procedure for manufacturing requires an iterative process involving parameter setting, execution of computational simulations, and modifying the parameters. The entire process demands substantial computational time, making it impractical for real-time feedback towards rapid corrective actions required for in-line control for running production processes. To overcome this challenge, artificial intelligence (AI) can be leveraged to determine optimal manufacturing parameters within a single manufacturing cycle time. This research proposes an in-line optimization framework incorporating a trained AI model to predict kidney-shaped die forming. Preliminary results indicate that the AI framework can accurately predict draw-in values based on a given parameter set, a process referred to as forward prediction. Furthermore, the AI framework can also predict the optimal parameter set that leads to the desired draw-in values, referred to as inverse optimization (or backward prediction). This research has been performed in collaborations with USCAR (US Council for Automotive Research) and AutoForm. The members of USCAR are Ford, GM, and Stellantis.

36 MATERIALS SCIENCE↗

Multilayer co-extrusion technique for developing high energy density organic devices.

The purpose of this project is to develop multi-layered co-extrusion (MLCE) capabilities at Sandia National Laboratories to produce multifunctional polymeric structures. Multi-layered structures containing layers of alternating electrical, mechanical, optical, or structural properties can be applied to a variety of potential applications including energy storage, optics, sensors, mechanical, and barrier applications relevant to the internal and external community. To obtain the desired properties, fillers must be added to the polymer materials that are much smaller than the end layer thickness. We developed two filled polymer systems, one for conductive layers and one for dielectric layers and demonstrated the potential for using MLCE to manufacture capacitors. We also developed numerical models to help determine the material and processing parameters that impact processing and layer stability.

36 MATERIALS SCIENCE↗

Plastic flow and microstructural instabilities during high-pressure torsion of Cu/ZnO composites

Highlights: • Hybrid bulk metal - ceramic nanoparticle material was processed by HPT. • ZnO nanoparticles exhibited significant plasticity of up to 86%. • Hydrodynamic instability determined the flow mode of ZnO particle clusters. • Microstructural stability of Cu decreased due to the co-deformation with ZnO. - Abstract: We conducted high-pressure torsion (HPT) of hybrid materials composed of two copper disks with a layer of ZnO ceramic nanoparticles sandwiched in-between. A detailed microstructural analysis of the processed samples revealed a surprisingly high level of plastic deformation introduced in individual ZnO particles, even though they possess a much high hardness than the surrounding Cu. Moreover, we demonstrated that by tailoring the initial geometry of the system (i.e. introducing holes in the cladding Cu disks), we can effectively change the flow mode of ZnO particle clusters from laminar to turbulent one and facilitate their deagglomeration process. Finally, the presence of ZnO particles decreased the microstructural stability of the Cu matrix. We discussed the obtained results in terms of hydrodynamic and microstructural instabilities during plastic deformation. This work expands our understandings of the cooperative severe plastic deformation of two dissimilar materials and sheds new light on the design of hybrid materials.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Electrically tunable materials for microwave applications

Microwave devices based on tunable materials are of vigorous current interest. Typical applications include phase shifters, antenna beam steering, filters, voltage controlled oscillators, matching networks, and tunable power splitters. The objective of this review is to assist in the material selection process for various applications in the microwave regime considering response time, required level of tunability, operating temperature, and loss tangent. The performance of a variety of material types are compared, including ferroelectric ceramics, polymers, and liquid crystals. Particular attention is given to ferroelectric materials as they are the most promising candidates when response time, dielectric loss, and tunability are important. However, polymers and liquid crystals are emerging as potential candidates for a number of new applications, offering mechanical flexibility, lower weight, and lower tuning voltages.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

MoS 2 -supported Au 31 for CO hydrogenation: A first-principle study

While the basal plane of single-layer molybdenum disulphide (MoS 2 ) is inert, attempts have been made to functionalize it chemically through the creation of defects and/or addition of dopants. With nanoparticles as dopants, the authors present density functional theory-based calculations of the hydrogenation of CO on a 31-atom, bilayer Au cluster supported on single-layer MoS 2 (Au31/MoS 2 ). Not surprisingly, the adsorption and reaction of all species involved in the hydrogenation occur at the edges of the cluster—the regions at which the interaction between MoS 2 and the Au cluster is tracked to be the strongest. The authors find two possible mechanisms that lead to the formation of methanol: (1) CO* → CHO* → CH 2 O* → CH 3 O* → CH 3 OH* and (2) CO* → CHO* → HCOH* → CH2OH* → CH3OH*, where * indicates the adsorbed species. Detailed analysis of the reaction pathways, however, does not result in favoring one mechanism over the other. Rather, both mechanisms are facile. In addition, the rate-limiting step in each mechanism is found to be the formation of the formyl radical group (CO* + H* → CHO*).

2D materials↗

What is needed for BISCO to work in a dipole insert for 20 tesla hybrid accelerator magnets

Developing HTS dipole inserts producing fields larger than 5 T within 15 T Nb3Sn outserts is necessary to generate 20 T or higher fields for future high energy colliders. Dipole inserts based on the cos-theta coil geometry with various stress management concepts and Bi2212 super-conducting strand and cable are being developed at Fermilab both within and beyond the U.S. national effort. On paper, the potential reach for the maximum magnetic field in existing or planned Nb3Sn outserts is close to 20 T, thanks to the progress realized in Bi2212 wires’ critical current density. To achieve the Bi2212 potential in accelerator magnets, however, a number of technological challenges still have to be faced. These for instance include the need to design billets that are adequate for Rutherford cabling; developing insulation processes and materials that prevent leaks, which reduce transport current and increase the risk of shorts; control and limit Bi2212 coils’ stresses and strains; reconsider the Split Melt Process (SMP) to lower costs and simplify the processing. This paper reviews Bi2212 conductor properties and coil technolo-gies, and proposes new ideas to face the challenges that Bi2212 still presents as an accelerator magnet conductor.

43 PARTICLE ACCELERATORS↗

Where Next with SRF?

RF superconductivity (SRF) has become, over the last ~20 years, the technology of choice to produce RF cavities for particle accelerators. This occurred because of improvements in material and processing techniques as well as the understanding and remediation of practical limitations in SRF cavities. This development effort span ~40 years and Nb has been the material of choice for SRF cavity production. As the performances of SRF Nb cavities are approaching what are considered to be theoretical limits of the material, it is legitimate to ask what will be the future of SRF. In this article we will attempt to answer this question on the basis of near-future demands for SRF-based accelerators and the basic SRF properties of the available materials. Clearly, Nb will continue to play a major role in SRF cavities in the coming years but the use of superconductors with higher critical temperature than Nb is also likely to occur.

43 PARTICLE ACCELERATORS↗

Nature of innovations affecting photovoltaic system costs

Innovations improve technology costs through various kinds of engineering advancements, including changes to materials choices and device or process designs. Understanding how these innovations relate to cost change can reveal aspects of the process of technology evolution, yet developing such understanding is often not possible with a strictly quantitative approach due to data limitations. In this paper we develop a hybrid quantitative-qualitative framework for relating specific innovations to cost change by using the variables in a quantitative technology cost change model as an organizing principle. We demonstrate this framework by applying it to the cost decline in photovoltaic (PV) systems over the last five decades. This framework generates new understanding of a set of innovations that contributed to PV modules’ sustained cost decline and the more modest trends observed in balance-of-system (BOS) costs. The results show the great diversity of innovations that affected PV costs, drawing on wide-ranging fields of expertise within scientific research and practice. We find that there are differences in the characteristics of innovations that reduced the cost of PV modules compared to innovations influencing BOS costs. Numerous module innovations reduced costs by advancing manufacturing tools and processes that improved material quality. Many BOS innovations reduced costs through a combination of component design changes, integration, automation, digitalization, and standardization. Overall, most innovations in our sample affected PV hardware. However, some also target ‘soft technologies’ such as task durations through innovations like fast-track permitting, which require improved collaboration and process streamlining. This framework also provides insight into the nature of knowledge spillovers between technologies. Both module and BOS hardware innovations show the benefits of PV’s position within an ‘ecosystem’ of continuously advancing technologies in many industries, in particular semiconductors and electronics, and also point to the importance of public institutions for accelerating testing, permitting, and training.

14 SOLAR ENERGY↗

Review: engineering particles using the aerosol-through-plasma method

For decades, plasma processing of materials on the nanoscale has been an underlying enabling technology for many 'planar' technologies, particularly virtually every aspect of modern electronics from integrated-circuit fabrication with nanoscale elements to the newest generation of photovoltaics. However, it is only recent developments that suggest that plasma processing can be used to make 'particulate' structures of value in fields, including catalysis, drug delivery, imaging, higher energy density batteries, and other forms of energy storage. In this paper, the development of the science and technology of one class of plasma production of particulates, namely, aerosol-through-plasma (A-T-P), is reviewed. Various plasma systems, particularly RF and microwave, have been used to create nanoparticles of metals and ceramics, as well as supported metal catalysts. Gradually, the complexity of the nanoparticles, and concomitantly their potential value, has increased. First, unique two-layer particles were generated. These were postprocessed to create unique three-layer nanoscale particles. Also, the technique has been successfully employed to make other high-value materials, including carbon nanotubes, unsupported graphene, and spherical boron nitride. Some interesting plasma science has also emerged from efforts to characterize and map aerosol-containing plasmas. For example, it is clear that even a very low concentration of particles dramatically changes plasma characteristics. Some have also argued that the local-thermodynamic-equilibrium approach is inappropriate to these systems. Instead, it has been suggested that charged- and neutral-species models must be independently developed and allowed to 'interact' only in generation terms.

36 MATERIALS SCIENCE↗

Development of neural network force fields for corrosion studies

To fully understand the chemistry and physics of corrosion, novel methods of simulation must be developed. One approach is designing machine learning (ML) algorithms integrated with density functional theory to develop adaptive force fields to gain insight into corrosion behavior namely at the surface of metal oxides. Current methods of modeling corrosion are slow due to the computational cost of resolving both reaction mechanics and mass transport processes. Machine learning methods can be implemented to obtain structure-activity relationships at both the molecular and bulk scale while still retaining the accuracy of density functional theory (DFT) and significantly decreasing the time needed for simulations of complex chemical processes in the various environments of corrosion. Multiscale models are needed for corrosion studies to fully understand its processes not only at the atomic length scale (chemical bonding, energies, and forces), but also at the nano and meso length scales (solid-state physics and material science processes). Current methods of study include DFT, molecular dynamics, and Monte Carlo. The limitation of DFT is that only a small number of atoms or molecules can be simulated at that level of theory. Density functional theory is used to study the electronic structure of atoms and molecules, and calculate the force component of each atom. However, these calculations are limited to about 1000 atoms. Custom periodic boundary conditions (PBC) can be used to describe the various environments and defects that affect the atomic forces to produce a large data set from which a training set can be derived. Machine learning can be utilized to overcome the barrier of modeling macroscopic and multi-scale processes from ab initio calculations through the development of adaptive force fields. Local environments determine the atomic forces of a given system, therefore adaptive force fields must be created to produce reliable quantum mechanical calculations. This can be achieved by developing a learning algorithm that uses the mapped atomic forces or fingerprint as an input to produce energies and magnetic moments as output. A systematic approach was used to begin to build a data set in order to accurately describe the atomic forces in various environments. In Figure 4 below, a simple PBC cell of Fe{sub 2}O{sub 3} was first optimized. A surface optimization was performed next, followed by a hydroxylated surface optimization. Once this calculation has converged, the adsorption of halide species to the hydroxylated surface will be investigated. TensorFlow is an open source platform for machine learning developed by Google. Using a high level application program interface (API) such as Keras allows for building and training ML models easily in a number of different environments and languages. For this project, a neural network was developed within Anaconda in Python. Future Work: Further development of reference data set; Refining neural network and learning algorithm; Fingerprinting atomic environment to enable mapping of atomic force components; Choosing appropriate training set from reference data; Learning from training set and enabling non-linear mapping of training set fingerprints and the atomic forces; Estimation of uncertainty to identify ranges of outside applicability; Testing and analysis of molecular dynamic simulations.

36 MATERIALS SCIENCE↗

Canted Undulator Upgrade for GeoSoilEnviroCARS Sector 13 at the Advanced Photon Source

Support for the beamline component of the canted undulator upgrade of Sector 13 (GeoSoilEnviroCARS; managed and operated by the University of Chicago) at the Advanced Photon Source (APS; Argonne National Laboratory) was received from three agencies (equally divided): NASA-SRLIDAP (now LARS), NSF-EAR-IF (ARRA) and DOE-Single Investigator Small Group (SISGR). The associated accelerator components (undulators, canted front end) were provided by the APS using DOE-ARRA funding. The intellectual merit of the research enabled by the upgrade lies in advancing our knowledge of the composition, structure and properties of earth materials; the processes they control; and the processes that produce them. The upgrade will facilitate scientific advances in the following areas: high pressure mineral physics and chemistry, non-crystalline and nano-crystalline materials at high pressure, chemistry of hydrothermal fluids, reactions at mineral-water interfaces, biogeochemistry, oxidation states of magmas, flow dynamics of fluids and solids, and cosmochemistry. The upgrade, allowing the microprobe to operate 100% of the time and the high pressure and surface scattering and spectroscopy instruments to receive beam time increases, will facilitate much more efficient use of the substantial investment in these instruments. The broad scientific community will benefit by the increase in the number of scientists who conduct cutting-edge research at GSECARS. The user program in stations 13ID-C (interface scattering) and 13ID-D (laser heated diamond anvil cell and large volume press) recommenced in June 2012. The operation of the 13ID-E microprobe station began in the Fall 2012 cycle (Oct.-Dec 2012). The upgraded canted beamlines double the amount of undulator beam time at Sector 13 and provide new capabilities including extended operations of the X-ray microprobe down to the sulfur K edge and enhanced brightness at high energy. The availability of the upgraded beamlines will advance the research being conducted at Sector 13.

47 OTHER INSTRUMENTATION↗