Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “load tests”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Performance characteristics of a diesel engine using low- and medium-energy gases as a fuel supplement (fumigation)

The use of low- and medium-energy gases derived from solid waste is investigated. Gases that simulate those gases that could be derived from refuse were injected into the air inlet of a 298-kilowatt (400 horsepower) diesel engine as a fuel supplement. This process is called fumigation. Three different gases with thermal-energy contents of 6.11 MJ/cu m (164 Btu/cu ft), 18.1 MJ/cu m (485 Btu/cu ft), and 18.8 MJ/cu m (505 Btu/cu ft, respectively, were used at rates ranging as high as 20 percent of the normal fuel oil energy at four different engine load points. The test results indicated approximately 100 percent gas energy utilization with no observable deleterious effect on the engine.

Monford, L. G.↗
NASA NTRS1977

Preliminary evaluation of fiber composite reinforcement of truck frame rails

The use of graphite fiber/resin matrix composite to effectively reinforce a standard steel truck frame rail is studied. A preliminary design was made and it was determined that the reinforcement weight could be reduced by a factor of 10 when compared to a steel reinforcement. A section of a 1/3 scale reinforced rail was fabricated to demonstrate low cost manufacturing techniques. The scale rail section was then tested and increased stiffness was confirmed. No evidence of composite fatigue was found after 500,000 cycles to a fiber stress of 34,000 psi. The test specimen failed in bending in a static test at a load 50 percent greater than that predicted for a non-reinforced rail.

Faddoul, J. R.↗
NASA NTRS1977

Experimental evaluation of foil-supported resilient-pad gas-lubricated thrust bearing

A new type of resilient-pad gas thrust bearing was tested to determine the feasibility of the design. The bearing consists of carbon graphite pads mounted asymmetrically on foil beams. Two bearing configurations were tested at thrust loads from 27 to 80 newtons at speeds to 9000 rpm. The outside diameter of the bearing was 8.9 centimeters.

Nemeth, Z. N.↗
NASA NTRS1979

Precision controllability of the F-15 airplane

A flying qualities evaluation conducted on a preproduction F-15 airplane permitted an assessment to be made of its precision controllability in the high subsonic and low transonic flight regime over the allowable angle of attack range. Precision controllability, or gunsight tracking, studies were conducted in windup turn maneuvers with the gunsight in the caged pipper mode and depressed 70 mils. This evaluation showed the F-15 airplane to experience severe buffet and mild-to-moderate wing rock at the higher angles of attack. It showed the F-15 airplane radial tracking precision to vary from approximately 6 to 20 mils over the load factor range tested. Tracking in the presence of wing rock essentially doubled the radial tracking error generated at the lower angles of attack. The stability augmentation system affected the tracking precision of the F-15 airplane more than it did that of previous aircraft studied.

Sisk, T. R.↗
NASA NTRS1979

Acoustic response of thin film windows in the environment of an Atlas-Centaur launch

An exhaustive design development study was performed to correlate the survivability of thin film to various parameters. Film material properties, film thicknesses, unsupported window areas, window aspect ratios, film/frame transitions, film reinforcing techniques, and material grain orientations were all considered. Several thin films were tested to acoustical loads which are expected during an Atlas-Centaur launch of the High Energy Astronomy Observatory Satellites (HEAO)

Mastronardi, R.↗
NASA NTRS1980

Study of the influence of hole quality on composite materials

The influence of hole quality on the structural behavior of composite materials was investigated. From an industry survey it was determined that the most frequent imperfections encountered during hole fabrication are chipout, delamination, and oversize conditions. These hole flaw types were generated in critical areas of static, compression, and fatigue specimens fabricated from T300/5208 graphite/epoxy system. The specimens were tested in static and cyclic pin bearing modes in addition to compression loading. Results of these tests are presented and discussed. The hole chipout defect reduced the static and cyclic endurance characteristics. Oversize holes also lowered the cyclic pin bearing endurance, but had no influence of the static pin bearing characteristics. Delamination had no insignificant influence on the static tension and cyclic pin bearing characteristics. Compression tests demonstrated a deleterious effect for chipout of delamination defects. Hole quality requirements proposed are discussed.

Pengra, J. J.↗
NASA NTRS1980

Evaluation of the cyclic behavior of aircraft turbine disk alloys, part 2

Several nickel-base aircraft turbine disk superalloys were evaluated at 650 C for resistance to fatigue crack initiation and propagation under cyclic and cyclic/dwell conditions. Controlled strain low cycle fatigue (LCF) and controlled load crack propagation tests were performed and results utilized to provide a direct comparison among the alloys. Tests were performed on selected alloys to evaluate the effects of hold times, mean stresses, stress-dwell cycle types, inert environment, and contractor test methods. At the lower total strain ranges of interest, the alloys exhibited generally increasing initiation life with increasing tensile strength for both cyclic (0.33 Hz) and cyclic/dwell (900-sec hold per cycle) conditions. Rank order of the alloys by LCF initiation life changed substantially at higher strain ranges, approaching the rank order expected from monotonic tensile ductilities. The effect of the 900 sec (15 min) hold time fatigue life varied significantly from alloy to alloy. Generally, the higher-strength, finer-grained alloys exhibited more significant reductions in fatigue life due to the dwell. The effects of mean strain were found to be negligible and the effects of mean stress were pronounced. At high strain ranges the mean stress was near zero and did not contribute to reduction in life. At low strain ranges, however, mean stresses were large and significant reductions in LCF lives occurred.

Cowles, B. A.↗
NASA NTRS1979

Space Shuttle solid rocket booster

Details of the design, operation, testing and recovery procedures of the reusable solid rocket boosters (SRB) are given. Using a composite PBAN propellant, they will provide the primary thrust (six million pounds maximum at 20 s after ignition) within a 3 g acceleration constraint, as well as thrust vector control for the Space Shuttle. The drogues were tested to a load of 305,000 pounds, and the main parachutes to 205,000. Insulation in the solid rocket motor (SRM) will be provided by asbestos-silica dioxide filled acrylonitrile butadiene rubber ('asbestos filled NBR') except in high erosion areas (principally in the aft dome), where a carbon-filled ethylene propylene diene monomer-neopreme rubber will be utilized. Furthermore, twenty uses for the SRM nozzle will be allowed by its ablative materials, which are principally carbon cloth and silica cloth phenolics.

Hardy, G. B.↗
NASA NTRS1978

Space Fabrication Demonstration System

The completion of assembly of the beam builder and its first automatic production of truss is discussed. A four bay, hand assembled, roll formed members truss was built and tested to ultimate load. Detail design of the fabrication facility (beam builder) was completed and designs for subsystem debugging are discussed. Many one bay truss specimens were produced to demonstrate subsystem operation and to detect problem areas.

Source record↗
NASA NTRS1981

Validation of helicopter noise prediction techniques

The current techniques of helicopter rotor noise prediction attempt to describe the details of the noise field precisely and remove the empiricisms and restrictions inherent in previous methods. These techniques require detailed inputs of the rotor geometry, operating conditions, and blade surface pressure distribution. The purpose of this paper is to review those techniques in general and the Farassat/Nystrom analysis in particular. The predictions of the Farassat/Nystrom noise computer program, using both measured and calculated blade surface pressure data, are compared to measured noise level data. This study is based on a contract from NASA to Bolt Beranek and Newman Inc. with measured data from the AH-1G Helicopter Operational Loads Survey flight test program supplied by Bell Helicopter Textron.

Succi, G. P.↗
NASA NTRS1981

Strength integrity of the Space Shuttle Orbiter tiles

The development of the thermal protection system (TPS) for shielding the Shuttle from high temperature aerodynamic heating during atmospheric entry is described. The TPS was required to limit structural heating to 350 F, be used for 100 flights, withstand temperature ranges from -250 to 2800 F, attach to an aluminum structure, and provide the aerodynamic moldline. More than 30,000 tiles of individual size, shape, and strength were bonded adhesively to a Nomex felt mat which coated critical areas of the craft. Densification processes for strengthening the tiles in highly loaded areas are outlined and stress sources for each mission phase are analyzed. Aerodynamic, acoustic, combined loads, and verification tests for stress levels up to 125% of nominal were performed for each tile. The one complete and 15 partial tiles lost during the initial flight were all lower strength, undensified tiles.

Moser, T. L.↗
NASA NTRS1982

The influence of orientation on the stress rupture properties of nickel-base superalloy single crystals

Constant load creep rupture tests were performed on MAR-M247 single crystals at 724 MPa and 774 C where the effect of anisotropy is prominent. The initial orientations of the specimens as well as the final orientations of selected crystals after stress rupture testing were determined by the Laue back-reflection X-ray technique. The stress rupture lives of the MAR-M247 single crystals were found to be largely determined by the lattice rotations required to produce intersecting slip, because second-stage creep does not begin until after the onset of intersecting slip. Crystals which required large rotations to become oriented for intersecting slip exhibited the shortest stress rupture lives, whereas crystals requiring little or no rotations exhibited the lowest minimum creep rates, and consequently, the longest stress rupture lives.

Mackay, R. A.↗
NASA NTRS1983

NASA/USAF research in structural dynamics

Research in the structural dynamics of large space structures is discussed. The problems of structural response are emphasized. Dynamic modeling, structural members, finite element techniques, axial loads, and vibration tests are among the topics discussed.

Pinson, L. D.↗
NASA NTRS1982

Superplastic forming/weld-brazing of titanium skin-stiffened compression panels

A study was conducted to exploit the processing advantages of superplastic forming and weld-brazing for the fabrication of titanium skin-stiffened structural components. Small titanium compression panels were fabricated and tested at room temperature. Stiffeners having configurations of a conventional hat shape, beaded shaped web, ribbed shaped web, or stepped shaped web were investigated. The data from the panel tests included load-shortening curves, local buckling strengths, and failure loads. Experimental buckling loads were compared with buckling loads calculated using a finite-element analysis. The superplastic formed/weld-brazed panels having complex shaped stiffeners developed from 20 to 58 percent higher local buckling strengths than panels with conventionally shaped stiffeners.

Royster, D. M.↗
NASA NTRS1982

Review of NASA antiskid braking research

NASA antiskid braking system research programs are reviewed. These programs include experimental studies of four antiskid systems on the Langley Landing Loads Track, flights tests with a DC-9 airplane, and computer simulation studies. Results from these research efforts include identification of factors contributing to degraded antiskid performance under adverse weather conditions, tire tread temperature measurements during antiskid braking on dry runway surfaces, and an assessment of the accuracy of various brake pressure-torque computer models. This information should lead to the development of better antiskid systems in the future.

Tanner, J. A.↗
NASA NTRS1983

Load deflection characteristics of inflated structures

A single, closed form relationship to relate load to the deformed dimensions of the horizontal torus was developed. Wall elasticity was included in the analysis, and special care was taken to predict the final footprint area of the loaded structure. The test fixture utilized is shown. The tori used for the bulk of the testing were rubber inner tubes for a 32 and 160 pneumatic tire. The inner tube being tested was plumbed, to a mercury-filled manometer, which had a 50 inch measurement capacity, by use of a special adapter. The adapter fit over the valve stem and allowed air to be added from a shop-air source and to be bled through the standard valve mechanism. In this fashion, tests requiring the maintenance of a constant indication of air pressure could be run with little difficulty.

Baumgarten, J. R.↗
NASA NTRS1984

Research opportunities for rotorcraft

The control of structural vibration is helicopters is discussed. Active control concepts, wind tunnel tests, rotor vibratory loads, systems integration, and engine control are among the topics discussed.

Blake, B. B.↗