Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Outer planet probe entry thermal protection. II - Heat shielding requirements

Solutions are presented for the material thermal response for heat shields of blunt probes entering Saturn and Uranus. Both monolithic and sandwich concepts were considered having exposed charring ablative or reflective materials. The solutions show that (1) Teflon heat shields are sized by mass loss considerations, other materials (unless entering the Uranus cold-dense atmosphere) by heat soak considerations, (2) steeper entries require less heat shield mass, (3) sizing requirements vary little about the bodies for heat soak dominated materials, and (4) carbon-phenolic appears superior overall, but silica is superior for the steeper entries and the high helium content atmospheres.

Nicolet, W. E.↗
NASA NTRS1975

An experimental investigation of heat transfer to reusable surface insulation tile array gaps in a turbulent boundary layer with pressure gradient

An experimental investigation was performed to determine the effect of pressure gradient on the heat transfer to space shuttle reusable surface insulation (RSI) tile array gaps under thick, turbulent boundary layer conditions. Heat transfer and pressure measurements were obtained on a curved array of full-scale simulated RSI tiles in a tunnel wall boundary layer at a nominal freestream Mach number of 10.3 and freestream unit Reynolds numbers of 1.6, 3.3, and and 6.1 million per meter. Transverse pressure gradients were induced over the model surface by rotating the curved array with respect to the flow. Definition of the tunnel wall boundary layer flow was obtained by measurement of boundary layer pitot pressure profiles, and flat plate wall pressure and heat transfer. Flat plate wall heat transfer data were correlated and a method was derived for prediction of smooth, curved array heat transfer in the highly three-dimensional tunnel wall boundary layer flow and simulation of full-scale space shuttle vehicle pressure gradient levels was assessed.

Throckmorton, D. A.↗
NASA NTRS1974

Correlation parameters for the study of leeside heating on a lifting body at hypersonic speeds

Leeside heating was studied with the aim of gaining some insight into: (1) the magnitude of the leeside heating rates and (2) the methods to be used to extrapolate wind tunnel leeside heating rates to the full scale flight condition. This study was based on existing experimental data obtained in a hypersonic shock tunnel on lifting body configurations that are typical of shuttle orbiter vehicles. Heat transfer was first measured on the windward side to determine the boundary layer type. Then the leeside heating was investigated with the classified boundary layer. Correlation data are given on the windward turbulent boundary layer, the windward laminar boundary layer, and the leeside surfaces.

Vidal, R. J.↗
NASA NTRS1974

Heat flow and geothermal potential of the East Mesa KGRA, Imperial Valley, California

The East Mesa KGRA (Known Geothermal Resource Area) is located in the southeast part of the Imperial Valley, California, and is roughly 150 kilometers square in areal extent. A new heat flow technique which utilizes temperature gradient measurements across best clays is presented and shown to be as accurate as conventional methods for the present study area. Utilizing the best clay gradient technique, over 70 heat flow determinations have been completed within and around the East Mesa KGRA. Background heat flow values range from 1.4 to 2.4 hfu (1 hfu = .000001 cal. per square centimeter-second) and are typical of those throughout the Basin and Range province. Heat flow values for the northwest lobe of the KGRA (Mesa anomaly) are as high as 7.9 hfu, with the highest values located near gravity and seismic noise maxima and electrical resistivity minima. An excellent correlation exists between heat flow contours and faults defined by remote sensing and microearthquake monitoring.

Swanberg, C. A.↗
NASA NTRS1975

The International Heat Pipe Experiment

On October 4, 1974 the International Heat Pipe Experiment was launched aboard a Black Brant Sounding Rocket from White Sands, New Mexico. The flight provided six minutes of near zero gravity during which a total of ten separate heat pipe experiments were performed. The fifteen heat pipes which were tested represent some of the latest American and European technology. This flight provided the first reported zero gravity data on cryogenic and flat plate vapor chamber heat pipes. Additionally, valuable design and engineering data was obtained on several other heat pipe configurations. This paper will discuss the payload and four of the individual experiments.

Mcintosh, R.↗
NASA NTRS1975

Cryogenic heat pipe experiment - Flight performance onboard a sounding rocket

Flight data from a 15.8 mm OD, 760 mm long, axial-groove, methane cryogenic heat pipe verified successful priming and operation during six min of zero-g time. The nominal power applied to the evaporator was 60-w for the first 60 sec of zero-g time, 14 w for the next 270 sec, and 25 w for the last 20 sec of flight. The heat pipe condenser was mounted into an aluminum heat sink which was cooled to 103 K at launch and increased in temperature to 128 K by the end of the flight. Ground test data obtained for the flight heat pipe, together with theoretical predictions, indicate a zero-g heat transport capability of 3500 to 4000 w-cm in the 100-125 K temperature range.

Harwell, W.↗
NASA NTRS1975

Atmospheric heating by solar EUV radiation

A diurnal model of the mid-latitude ionospheric R region is used to calculate the diurnal variation of the neutral gas heating rates and neutral gas heating efficiency for conditions similar to those over Millstone Hill on March 23-24, 1970. The calculations show that the absorbed solar EUV (wavelength less than or equal to 1025 A) energy is almost equally split between photoelectrons and ion pair production. Photoelectrons heat the ambient electron gas by Coulomb collisions and by the quenching of certain excited ion species, whereas the ion gas is primarily heated by collisions with hot electrons and by chemical reactions. Heating processes above 300 km, between 170 and 300 km, and below 170 km are identified.

Stolarski, R. S.↗
NASA NTRS1976

Flight data analysis and further development of variable-conductance heat pipes

Continuing efforts in large gains in heat-pipe performance are reported. It was found that gas-controlled variable-conductance heat pipes can perform reliably for long periods in space and effectively provide temperature stabilization for spacecraft electronics. A solution was formulated that allows the control gas to vent through arterial heat-pipe walls, thus eliminating the problem of arterial failure under load, due to trace impurities of noncondensable gas trapped in an arterial bubble during priming. This solution functions well in zero gravity. Another solution was found that allows priming at a much lower fluid charge. A heat pipe with high capacity, with close temperature control of the heat source and independent of large variations in sink temperature was fabricated.

Enginer, J. E.↗
NASA NTRS1976

Shock interference heat transfer to tank configurations mated to a straight-wing space shuttle orbiter at Mach number 10.3

Heat transfer was measured on a space shuttle-tank configuration with no mated orbiter in place and with the orbiter in 10 different mated positions. The orbiter-tank combination was tested at angles of attack of 0 deg and 5 deg, at a Mach number of 10.3, and at a free-stream Reynolds number of one million based on the length of the tank. Comparison of interference heat transfer with no-interference heat transfer shows that shock interference can increase the heat transfer to the tank by two orders of magnitude along the ray adjacent to the orbiter and can cause high temperature gradients along the tank skin. The relative axial location of the two mated vehicles determined the location of the sharp peaks of extreme heating as well as their magnitude. The other control variables (the angle of attack, the gap, and the cross-section shape) had significant effects that were not as consistent or as extreme.

Crawford, D. H.↗
NASA NTRS1976

An inexpensive economical solar heating system for homes

A low-cost solar home heating system to supplement existing warm-air heating systems is described. The report is written in three parts: (1) a brief background on solar heating, (2) experience with a demonstration system, and (3) information for the homeowner who wishes to construct such a system. Instructions are given for a solar heating installation in which the homeowner supplies all labor necessary to install off-the-shelf components estimated to cost $2,000. These components, which include solar collector, heat exchanger, water pump, storage tank, piping, and controls to make the system completely automatic, are available at local lumber yards, hardware stores, and plumbing supply stores, and are relatively simple to install. Manufacturers and prices of each component used and a rough cost analysis based on these prices are included. This report also gives performance data obtained from a demonstration system which was built and tested at the Langley Research Center.

Allred, J. W.↗
NASA NTRS1976

Heat shield characterization: Outer planet atmospheric entry probe

A full scale carbon phenolic heat shield was fabricated for the Outer Planet Probe in order to demonstrate the feasibility of molding large carbon phenolic parts with a new fabrication processing method (multistep). The sphere-cone heat shield was molded as an integral unit with the nose cap plies configured into a double inverse chevron shape to achieve the desired ply orientation. The fabrication activity was successful and the feasibility of the multistep processing technology was established. Delaminations or unbonded plies were visible on the heat shield and resulted from excessive loss of resin and lack of sufficient pressure applied on the part during the curing cycle. A comprehensive heat shield characterization test program was conducted, including: nondestructive tests with the full scale heat shield and thermal and mechanical property tests with small test specimen.

Mezines, S. A.↗
NASA NTRS1976

Initial operation of a solar heating and cooling system in a full-scale solar building test facility

The Solar Building Test Facility (SBTF) was constructed to advance the technology for heating and cooling of office buildings with solar energy. Its purposes are to (1) test system components which include high-performing collectors, (2) test the performance of a complete solar heating and cooling system, (3) investigate component interactions, and (4) investigate durability, maintenance and reliability of components. The SBTF consists of a 50,000 square foot office building modified to accept solar heated water for operation of an absorption air conditioner and for the baseboard heating system. A 12,666 square foot solar collector field with a 30,000 gallon storage tank provides the solar heated water. A description of the system and the collectors selected is printed along with the objectives, test approach, expected system performance, and some preliminary results.

Knoll, R. H.↗
NASA NTRS1976

Theoretical and empirical low perigee aerodynamic heating during orbital flight of an atmosphere explorer

This document presents the results of an extensive, low perigee, orbital aerodynamic heating study undertaken in support of the Atmosphere Explorer-C Temperature Alarm. Based upon in-flight orbital temperature data from the Temperature Alarm tungsten resistance wire thermometer, aerodynamic heating rates have been determined for eight selected orbits by means of a reduced thermal analytical model verified by both ground test and flight data. These heating rates are compared with the classical free molecular and first order collision regime values. It has been concluded that, for engineering purposes, the aerodynamic heating rate of atmospheric gases at perigee altitudes between 170 and 135 km on pure tungsten wire is 30 to 60% of the value set by the classical free molecular limit. Relative to the more usual orbital thermal input attributable to direct solar radiation, the aerodynamic heating rate at the lowest altitude attempted with the spacecraft despun (135 km) is the equivalent of about 1.2 solar constants incident on a tungsten wire with a solar absorptivity of 0.85.

Caruso, P. S., Jr.↗
NASA NTRS1976

Lightweight Long Life Heat Exchanger

A shuttle orbiter flight configuration aluminum heat exchanger was designed, fabricated, and tested. The heat exchanger utilized aluminum clad titanium composite parting sheets for protection against parting sheet pin hole corrosion. The heat exchanger, which is fully interchangeable with the shuttle condensing heat exchanger, includes slurpers (a means for removing condensed water from the downstream face of the heat exchanger), and both the core air passes and slurpers were hydrophilic coated to enhance wettability. The test program included performance tests which demonstrated the adequacy of the design and confirmed the predicted weight savings.

Moore, E. K.↗
NASA NTRS1976

Investigation of performance limits in axial groove heat pipes

The entrainment-shear performance limit which occurs in axial groove heat pipes was investigated and explained. In the existing heat pipe literature the entrainment heat flux limit is defined as the condition where the Weber number is greater than or equal to one. In this analysis, the critical value for the entrainment Weber number is found to be 2 pi less than or equal to 3 pi. Perhaps more important to the heat pipe designer than the entrainment performance limit is the prediction of the performance degradation due to vapor-liquid shearing stress which is also described. Preliminary qualitative experiments were conducted to observe the shear. stress wave formation phenomena. The equations presented may be used to predict and minimize the vapor-liquid shear stress performance effects that occur in axial groove and puddle flow artery heat pipes.

Feldman, K. T.↗
NASA NTRS1976

The International Heat Pipe Experiment

On October 4, 1974, the International Heat Pipe Experiment was launched aboard a Black Brant sounding rocket from White Sands, New Mexico. The flight provided six min of near zero gravity during which a total of ten separate heat pipe experiments was performed. The fifteen heat pipes tested represent some of the latest American and European technology. This flight provided the first reported zero gravity data on cryogenic and flat plate vapor chamber heat pipes. Additionally, valuable design and engineering data were obtained on several other heat pipe configurations. The payload and several of its experiments are discussed.

Mcintosh, R.↗
NASA NTRS1975

Silica heat shield sizing

The sensitivity of silica heat shield requirements to gap width, tile edge radius, and heat transfer distribution within tile gaps was investigated. A two-dimensional thermal model was modified and used to determine the effect of two dimensional heat transfer distributions at high temperature reusable surface insulation edges on shuttle thermal protection system (TPS) requirements. The sensitivity of TPS requirements to coating thickness, emissivity, substructure thickness, and changes in gap heating for several locations on shuttle was also studied. An inverse solution technique was applied to temperature data obtained in the Ames 20 MW turbulent duct in order to examine the effect of tile edge radius on TPS requirements. The derived heating values were then used to predict TPS requirements. Results show that increasing tile radius reduces TPS requirements.

Ebbesmeyer, L. H.↗
NASA NTRS1976

Brayton-cycle heat exchanger technology program

The following five tasks designed to advance this development of heat exchanger systems for close loop Brayton cycle power systems are presented: (1) heat transfer and pressure drop data for a finned tubular heat transfer matrix. The tubes are arranged in a triangular array with copper stainless steel laminate strips helically wound on the tubes to form a disk fin geometry; (2) the development of a modularized waste heat exchanger. Means to provide verified double containment are described; (3) the design, fabrication, and test of compact plate fin heat exchangers representative of full scale Brayton cycle recuperators; (4) the analysis and design of bellows suitable for operation at 1600 F and 200 psia for 1,000 cycles and 50,000 hours creep life; and (5) screening tests used to select a low cost braze alloy with the desirable attributes of a gold base alloy. A total of 22 different alloys were investigated; the final selection was Nicrobraz 30.

Killackey, J. J.↗