Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “correction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

The elastic modulus correction term in creep activation energies Applied to oxide dispersion strengthened superalloy

The effect of elastic modulus and the temperature dependence of elastic modulus on creep activation energies for an oxide dispersion strengthened nickel-base superalloy are investigated. This superalloy is commercially known as Inconel Alloy MA 753, strengthened both by gamma-prime precipitates and by yttria particles. It is shown that at intermediate temperatures, say below 1500 F, where elastic modulus is weakly dependent on temperature, the modulus correction term to creep activation energy is small. Accordingly, modulus corrections are insignificant for the superalloy considered, which shows high apparent creep activation energies at this temperature. On the contrary, at very high temperatures, the elastic modulus correction term can be significant, thus reducing the creep activation energy to that of vacancy self-diffusion. In order to obtain high-temperature creep resistance, a high-value elastic modulus with a weak dependence on temperature is required.

Malu, M.↗

Atomic electron energies including relativistic effects and quantum electrodynamic corrections

Atomic electron energies have been calculated relativistically. Hartree-Fock-Slater wave functions served as zeroth-order eigenfunctions to compute the expectation of the total Hamiltonian. A first order correction to the local approximation was thus included. Quantum-electrodynamic corrections were made. For all orbitals in all atoms with 2 less than or equal to Z less than or equal to 106, the following quantities are listed: total energies, electron kinetic energies, electron-nucleus potential energies, electron-electron potential energies consisting of electrostatic and Breit interaction (magnetic and retardation) terms, and vacuum polarization energies. These results will serve for detailed comparison of calculations based on other approaches. The magnitude of quantum electrodynamic corrections is exhibited quantitatively for each state.

Aoyagi, M.↗

Monthly mean forecast experiments with the GISS model - Correction

One of the three monthly mean forecasts computed previously by Spar et al., (1976) with the GISS (Goddard Institute for Space Studies) general circulation model was started from incorrect initial conditions. For the January 1975 prediction, a climatological mean January data set was accidentally substituted for the required January 1, 1975 initial data. In the present paper, the forecast for January 1975 is computed with the proper initial conditions, and the corrected results are presented. It is shown that the use of correct initial conditions improves the gross forecast mean energetics. In general, the use of correct initial conditions has resulted in a modest improvement in the monthly mean forecast for January 1975, but has not altered any of the previous conclusions by Spar et al.

Spar, J.↗

A technique to correct for sample thickness variations for use with IDAPS X-ray radiograph analysis

The Image Data Processing System (IDAPS) at the Marshall Space Flight Center is used to analyze radiographs of metal samples to qualitatively and quantitatively map compositional variations across the samples. When the X-ray radiographs are of samples having thickness variations, corrections must be made to accomplish compositional analysis. A correction technique is described for cylindrical samples and is applied to radiographs of SPAR Experiment 74-18. Uncorrected and corrected images are shown.

Schafer, C. F.↗

Forwardscattering corrections for optical extinction measurements in aerosol media. I - Monodispersions

A parametric investigation of forwardscattering corrections applicable to experimentally determined optical extinction coefficients in homogeneous aerosol media is discussed for the case of monodispersion. Assuming forwardscattering to be a single-scattering phenomenon, corrections are made by two methods: one employing the exact Mie theory, the other employing the approximate Rayleigh diffraction formula. The corrections are evaluated as functions of particle size, the real and imaginary parts of the complex refractive index, and the half-angle of the detector view cone.

Deepak, A.↗

Directional errors of movements and their correction in a discrete tracking task

Subjects can correct their own errors of movement more quickly than they can react to external stimuli by using three general categories of feedback: (1) knowledge of results, primarily visually mediated; (2) proprioceptive or kinaesthetic such as from muscle spindles and joint receptors, and (3) corollary discharge or efference copy within the central nervous system. The effects of these feedbacks on simple reaction time, choice reaction time, and error correction time were studied in four normal human subjects. The movement used was plantarflexion and dorsiflexion of the ankle joint. The feedback loops were modified, by changing the sign of the visual display to alter the subject's perception of results, and by applying vibration at 100 Hz simultaneously to both the agonist and antagonist muscles of the ankle joint. The central processing was interfered with when the subjects were given moderate doses of alcohol (blood alcohol concentration levels of up to 0.07%). Vibration and alcohol increase both the simple and choice reaction times but not the error correction time.

Jaeger, R. J.↗

Ellipsoidal corrections for geoid undulation computations

The computation of accurate geoid undulations is usually done combining potential coefficient information and terrestrial gravity data in a cap surrounding the computation point. In doing this a spherical approximation is made that can cause the errors that were investigated. The equations dealing with ellipsoidal corrections developed by Lelgemann and by Moritz were used to develop a computational procedure considering the ellipsoid as a reference surface. Terms in the resulting expression for the geoid undulation are identified as ellipsoidal correction terms. These equations were developed for the case where the Stokes function is used, and for the case where the modified Stokes function is used. For a cap of 20 deg the correction can reach -33 cm.

Rapp, R. H.↗

Alignment and evaluation of the cryogenic corrected infrared astronomical satellite /IRAS/ telescope

Room temperature alignment and evaluation techniques for the Infrared Astronomical Satellite (IRAS) telescope, which has a primary mirror figured to correct for surface distortions and the 2 K operating temperature are discussed. Interferometric cryogenic testing of the 0.6 m, f/1.5 lightweighted beryllium primary mirror at its intended operating temperature reveals surface distortions that can be modeled with Zernike polynomials. With this model, it becomes possible to derive the 'inverse' of the cryowavefront error (ideal cryo mirror) and to figure the cryo correction into the primary mirror using Perkin-Elmer's Computer Controlled Polisher. It is recognized that during room temperature assembly of the system, misalignment of the secondary mirror can introduce additional unwanted aberrations that may cancel or distort the wavefront errors purposely introduced by the cryo figuring. To avoid this possible degradation and to ensure optimum telescope performance, the system Zernike polynomial coefficients and wavefront maps generated from the in-process alignment interferograms are monitored and compared to Zernike coefficients and wavefront maps for the cryo corrected primary mirror.

Harned, N.↗

Onboard utilization of ground control points for image correction. Volume 2: Analysis and simulation results

An approach to remote sensing that meets future mission requirements was investigated. The deterministic acquisition of data and the rapid correction of data for radiometric effects and image distortions are the most critical limitations of remote sensing. The following topics are discussed: onboard image correction systems, GCP navigation system simulation, GCP analysis, and image correction analysis measurement.

Source record↗

Ionospheric propagation correction modeling for satellite altimeters

The theoretical basis and avaliable accuracy verifications were reviewed and compared for ionospheric correction procedures based on a global ionsopheric model driven by solar flux, and a technique in which measured electron content (using Faraday rotation measurements) for one path is mapped into corrections for a hemisphere. For these two techniques, RMS errors for correcting satellite altimeters data (at 14 GHz) are estimated to be 12 cm and 3 cm, respectively. On the basis of global accuracy and reliability after implementation, the solar flux model is recommended.

Nesterczuk, G.↗

Higher-order flow angle corrections for three-dimensional wind tunnel wall interference

A second-order theory including camber effects in wind tunnel wall interference corrections is described. Changes in the geometrical configuration of the model tested are avoided by introducing the camber correction as an equivalent angle-of-attack correction. Tabular and graphic data are presented which indicate improved accuracy for second-order over first-order theory.

Rizk, M. H.↗

Wall interference correction improvements for the ONERA main wind tunnels

This paper describes improved methods of calculating wall interference corrections for the ONERA large windtunnels. The mathematical description of the model and its sting support have become more sophisticated. An increasing number of singularities is used until an agreement between theoretical and experimental signatures of the model and sting on the walls of the closed test section is obtained. The singularity decentering effects are calculated when the model reaches large angles of attack. The porosity factor cartography on the perforated walls deduced from the measured signatures now replaces the reference tests previously carried out in larger tunnels. The porosity factors obtained from the blockage terms (signatures at zero lift) and from the lift terms are in good agreement. In each case (model + sting + test section), wall corrections are now determined, before the tests, as a function of the fundamental parameters M, CS, CZ. During the windtunnel tests, the corrections are quickly computed from these functions.

Vaucheret, X.↗

LANDSAT-4 Radiometric and Geometric Correction and Image Enhancement Results

Techniques were developed or improved to calibrate, enhance, and geometrically correct LANDSAT-4 satellite data. Statistical techniques to correct data radiometry were evaluated and were found to minimize striping and banding. Conventional techniques cause striping even with perfect calibration parameters. Intensity enhancement techniques were improved to display image data with large variation in intensity or brightness. Data were geometrically corrected to conform to a 1:100,000 map reference and image products produced with the map overlay. It is shown that these products can serve as accurate map products. A personal computer was experimentally used for digital image processing.

Bernstein, R.↗

Error analysis and correction of discrete solutions from finite element codes

Many structures are an assembly of individual shell components. Therefore, results for stresses and deflections from finite element solutions for each shell component should agree with the equations of shell theory. This paper examines the problem of applying shell theory to the error analysis and the correction of finite element results. The general approach to error analysis and correction is discussed first. Relaxation methods are suggested as one approach to correcting finite element results for all or parts of shell structures. Next, the problem of error analysis of plate structures is examined in more detail. The method of successive approximations is adapted to take discrete finite element solutions and to generate continuous approximate solutions for postbuckled plates. Preliminary numerical results are included.

Thurston, G. A.↗

Validation of the Thematic Mapper radiometric and geometric correction algorithms

The radiometric and geometric correction algorithms for Thematic Mapper are critical to subsequent successful information extraction. Earlier Landsat scanners, known as Multispectral Scanners, produce imagery which exhibits striping due to mismatching of detector gains and biases. Thematic Mapper exhibits the same phenomenon at three levels: detector-to-detector, scan-to-scan, and multiscan striping. The cause of these variations has been traced to variations in the dark current of the detectors. An alternative formulation has been tested and shown to be very satisfactory. Unfortunately, the Thematic Mapper detectors exhibit saturation effects suffered while viewing extensive cloud areas, and is not easily correctable. The geometric correction algorithm has been shown to be remarkably reliable. Only minor and modest improvements are indicated and shown to be effective.

Fischel, D.↗

Survey of ONERA activities on adaptive-wall applications and computation of residual corrections

The research undertaken concerning the computation and/or reduction of wall interference follows two main axes: improvement of wall correction determinations, and use of adaptive flexible walls. The use of wall-measured data to compute interference effects is reliable when the model representation is assessed by signatures with known boundary conditions. When the computed interferences are not easily applicable to correcting the results (especially for gradients in two-dimensional cases), the flexible adaptive walls in operation in T2 are an efficient and assessed means of reducing the boundary effects to a negligible level, if the direction and speed of the flow are accurately measured on the boundary. The extension of the use of adaptive walls to three-dimensional cases may be attempted since the residual corrections are assumed to be small and are computable.

Chevallier, J. P.↗

Local strain redistribution corrections for a simplified inelastic analysis procedure based on an elastic finite-element analysis

Strain redistribution corrections were developed for a simplified inelastic analysis procedure to economically calculate material cyclic response at the critical location of a structure for life prediction proposes. The method was based on the assumption that the plastic region in the structure is local and the total strain history required for input can be defined from elastic finite-element analyses. Cyclic stress-strain behavior was represented by a bilinear kinematic hardening model. The simplified procedure predicts stress-strain response with reasonable accuracy for thermally cycled problems but needs improvement for mechanically load-cycled problems. Neuber-type corrections were derived and incorporated in the simplified procedure to account for local total strain redistribution under cyclic mechanical loading. The corrected simplified method was used on a mechanically load-cycled benchmark notched-plate problem. The predicted material response agrees well with the nonlinear finite-element solutions for the problem. The simplified analysis computer program was 0.3% of the central processor unit time required for a nonlinear finite-element analysis.

Kaufman, A.↗