Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Vehicles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Some tether applications with small launch vehicles

This paper describes four potentially useful tether applications that are best suited to or even limited to small launch vehicles and their payloads. The first application uses a Small Expendable-tether Deployment System (SEDS) to deploy a 20-40 km tether which transfers momentum from the spent final stage to its payload. This de-orbits the stage and boosts the payload. The other concepts are endo-atmospheric applications specific to various kinds of boosters. In one, a large helicopter gently recovers a reusable booster while it is descending by parachute. Another improves the performance of a small single-stage-to-orbit launch vehicle, by lifting it by helicopter to an altitude of about 3 kilometers before ignition. The last tows an air-breathing launch vehicle to high speed behind a supersonic aircraft, to eliminate any need for low-speed propulsion on the launch vehicle.

Carroll, Joseph A.↗
NASA NTRS1990

Assured Crew Return Vehicle flowfield and aerodynamic characteristics

A lifting body has been proposed as a candidate for the Assured Crew Return Vehicle which will serve as crew rescue vehicle for the Space Station. The focus of this work is on body surface definition, surface and volume grid definition, and the computation of inviscid flowfields about the vehicle at wind-tunnel conditions. Very good agreement is shown between the computed aerodynamic characteristics of the vehicle at a freestream Mach number of 10 and those measured in wind-tunnel tests.

Weilmuenster, K. James↗
NASA NTRS1990

Design considerations for honeycomb double-bubble tanks utilized in aerospace vehicles

Future earth-to-orbit vehicles will utilize reusable internal fuel tanks requiring most of the vehicle volume. Because weight reduction and volumetric efficiency are essential, these tanks will be integral to the vehicle structure, and the vehicle cross section will dictate the size and shape of the tank. For a fuselage with a noncircular cross section, a multibubble tank configuration may be employed. Multibubble tanks offer a reduction in tank weight over a single-lobe tank or several cylindrical tanks in a noncircular cross section but sacrifice the efficiency of utilizing the entire fuselage cross section. This paper includes a general configuration analysis of a double-bubble tank, a materials and efficiency study, and a complete mission design analysis centers on sizing the tank to withstand ascent and reentry loads while minimizing the structural weight.

Lentz, Christopher A.↗
NASA NTRS1990

Cargo launch vehicles to low earth orbit

There are two primary space transportation capabilities required to support both base programs and expanded mission requirements: earth-to-orbit (ETO) transportation systems and space transfer vehicle systems. Existing and new ETO vehicles required to support mission requirements, and planned robotic missions, along with currently planned ETO vehicles are provided. Lunar outposts, Mars' outposts, base and expanded model, ETO vehicles, advanced avionics technologies, expert systems, network architecture and operations systems, and technology transfer are discussed.

Austin, Robert E.↗
NASA NTRS1990

Evaluation of Proposed Rocket Engines for Earth-to-Orbit Vehicles

The objective is to evaluate recently analyzed rocket engines for advanced Earth-to-orbit vehicles. The engines evaluated are full-flow staged combustion engines and split expander engines, both at mixture ratios at 6 and above with oxygen and hydrogen propellants. The vehicles considered are single-stage and two-stage fully reusable vehicles and the Space Shuttle with liquid rocket boosters. The results indicate that the split expander engine at a mixture ratio of about 7 is competitive with the full-flow staged combustion engine for all three vehicle concepts. A key factor in this result is the capability to increase the chamber pressure for the split expander as the mixture ratio is increased from 6 to 7.

Martin, James A.↗
NASA NTRS1991

Guidance and control analysis of the entry of a lifting body personnel launch vehicle

NASA is currently involved in definition studies of a Personnel Launch System (PLS) that could be used to transport people to and from low-earth orbit. This vehicle would serve both to complement the Space Shuttle and to provide alternative access to space in the event the Space Shuttle fleet were unavailable for a prolonged period. The PLS would consist of a manned spacecraft launched by an expendable vehicle, e.g., Titan 4. One promising candidate for the manned component of the PLS is the NASA Langley Research Center HL-20 lifting body. Many studies are currently underway to assess this vehicle, and one of the main areas of study is the development of the capability to successfully enter, glide to the landing site, and land. To provide this capability, guidance and control algorithms have been developed, incorporated into a six-degree-of-freedom simulation, and evaluation in the presence of off-nominal atmospheric conditions, consisting of both density variations and steady-state winds. In addition, the impact of atmospheric turbulence was examined for the portion of flight from Mach 3.5 to touchdown. This analysis showed that the vehicle remained controllable and could successfully land even in the presence of off-nominal atmospheric conditions.

Powell, Richard W.↗
NASA NTRS1990

Design and analysis of composite primary structures for advanced launch vehicles

The current status of the Lightweight Composite Intertank Structures (LCIS) study, a program aimed at developing technologies required to apply advanced composite materials to launch vehicle primary structures, is reviewed. The launch system concept used for establishing design requirements consisted of a fully reusable winged booster and a partially reusable core vehicle. The component selected from this system for design and manufacturing studies was the core vehicle intertank adapter, a component consisting of approximately 26-ft diameter by 25 ft long stiffened cylindrical structure that separates the liquid hydrogen and liquid oxygen tanks on the core vehicle. The discussion covers the program approach, design requirements, material properties, structural analysis, and the test program.

Rix, C.↗
NASA NTRS1991

Ascent performance issues of a vertical-takeoff rocket launch vehicle

Advanced manned launch systems studies under way at the NASA Langley Research Center are part of a broader effort that is examining options for the next manned space transportation system to be developed by the United States. One promising concept that uses near-term technologies is a fully reusable, two-stage vertical-takeoff rocket vehicle. This vehicle features parallel thrusting of the booster and orbiter with the booster cross-feeding the propellant to the orbiter until staging. In addition, after staging, the booster glides back unpowered to the launch site. This study concentrated on two issues that could affect the ascent performance of this vehicle. The first is the large gimbal angle range required for pitch trim until staging because of the propellant cross-feed. Results from this analysis show that if control is provided by gimballing of the rocket engines, they must gimbal greater than 20 deg, which is excessive when compared with current vehicles. However, this analysis also showed that this limit could be reduced to 10 deg if gimballing were augmented by throttling the booster engines. The second issue is the potential influence of off-nominal atmospheric conditions (density and winds) on the ascent performance. This study showed that a robust guidance algorithm could be developed that would insure accurate insertion, without prelaunch atmospheric knowledge.

Powell, Richard W.↗
NASA NTRS1991

Numerical analysis and simulation of an assured crew return vehicle flow field

A lifting body was proposed as a candidate for the Assured Crew Return Vehicle (ACRV) which will serve as a crew rescue vehicle for the Space Station Freedom. The focus is on body surface definition, both surface and volume grid definition, and the computation of inviscid flow fields about the vehicle at wind tunnel conditions. Very good agreement is shown between the computed aerodynamic characteristics of the vehicle at M(sub infinity) = 10 and those measured in wind tunnel tests at high Reynolds numbers.

Weilmuenster, K. James↗
NASA NTRS1991

Overview of the Beta II Two-Stage-To-Orbit vehicle design

A study of a near-term, low risk two-stage-to-orbit (TSTO) vehicle was undertaken. The goal of the study was to assess a fully reusable TSTO vehicle with horizontal takeoff and landing capability that could deliver 10,000 pounds to a 120 nm polar orbit. The configuration analysis was based on the Beta vehicle design. A cooperative study was performed to redesign and refine the Beta concept to meet the mission requirements. The vehicle resulting from this study was named Beta II. It has an all-airbreathing first stage and a staging Mach number of 6.5. The second stage is a conventional wing-body configuration with a single SSME.

Plencner, Robert M.↗
NASA NTRS1991

Air-breathing hypersonic vehicle guidance and control studies; An integrated trajectory/control analysis methodology: Phase 1

A tool which generates optimal trajectory/control histories in an integrated manner is generically adapted to the treatment of single-stage-to-orbit air-breathing hypersonic vehicles. The methodology is implemented as a two point boundary value problem solution technique. Its use permits an assessment of an entire near-minimum-fuel trajectory and desired control strategy from takeoff to orbit while satisfying physically derived inequality constraints and while achieving efficient propulsive mode phasing. A simpler analysis strategy that partitions the trajectory into several boundary condition matched segments is also included to construct preliminary trajectory and control history representations with less computational burden than is required for the overall flight profile assessment. A demonstration was accomplished using a tabulated example (winged-cone accelerator) vehicle model that is combined with a newly developed multidimensional cubic spline data smoothing routine. A constrained near-fuel-optimal trajectory, imposing a dynamic pressure limit of 1000 psf, was developed from horizontal takeoff to 20,000 ft/sec relative air speed while aiming for a polar orbit. Previously unspecified propulsive discontinuities were located. Flight regimes demanding rapid attitude changes were identified, dictating control effector and closed-loop controller authority was ascertained after evaluating effector use for vehicle trim. Also, inadequacies in vehicle model representations and specific subsystem models with insufficient fidelity were determined based on unusual control characteristics and/or excessive sensitivity to uncertainty.

Hattis, Philip D.↗
NASA NTRS1991

Final design report of a personnel launch system and a family of heavy lift launch vehicles

The objective was to design both a Personnel Launch System (PLS) and a family of Heavy Lift Launch Vehicles (FHLLVs) that provide low cost and efficient operation in missions not suited for the Shuttle. The PLS vehicle is designed primarily for space station crew rotation and emergency crew return. The final design of the PLS vehicle and its interior is given. The mission of the FHLLVs is to place large, massive payloads into Earth orbit with payload flexibility being considered foremost in the design. The final design of three launch vehicles was found to yield a payload capacity range from 20 to 200 mt. These designs include the use of multistaged, high thrust liquid engines mounted on the core stages of the rocket.

Tupa, James↗
NASA NTRS1992

An electromechanical actuation system for an expendable launch vehicle

A major effort at the NASA Lewis Research Center in recent years has been to develop electro-mechanical actuators (EMA's) to replace the hydraulic systems used for thrust vector control (TVC) on launch vehicles. This is an attempt ot overcome the inherent inefficiencies and costs associated with the existing hydraulic structures. General Dynamics Space Systems Division, under contract to NASA Lewis, is developing 18.6 kW (25 hp), 29.8 kW (40 hp), and 52.2 kW (70 hp) peak EMA systems to meet the power demands for TVC on a family of vehicles developed for the National Launch System. These systems utilize a pulse population modulated converter and field-oriented control scheme to obtain independent control of both the voltage and frequency. These techniques allow an induction motor to be operated at its maximum torque at all times. At NASA Lewis, we are building on this technology to develop our own in-house system capable of meeting the peak power requirements for an expendable launch vehicle (ELV) such as the Atlas. Our EMA will be capable of delivering 22.4 kW (30 hp) peak power with a nominal of 6.0 kW (8 hp). This system differs from the previous ones in two areas: (1) the use of advanced control methods, and (2) the incorporation of built-in-test. The advanced controls are essential for minimizing the controller size, while the built-in-test is necessary to enhance the system reliability and vehicle health monitoring. The ultimate goal of this program is to demonstrate an EMA which will be capable of self-test and easy integration into other projects. This paper will describe the effort underway at NASA Lewis to develop an EMA for an Atlas class ELV. An explanation will be given for each major technology block, and the status of each major technology block and the status of the overall program will be reported.

Burrows, Linda M.↗
NASA NTRS1991

Is bigger always better? An economic study of U.S. ETO vehicle architectures

This analysis, performed as part of NASA's Space Transportation Infrastructure Study, compares the cost efficiency of two candidate launch vehicle families, used in conjunction with existing expendable launch vehicles and the Shuttle, to accomplish the nation's future space missions through 2030. Missions analyzed include those identified in NASA's Civil Needs Data Base (CNDB) and Space Exploration Initiative (SEI) Option E program, as well as estimates of commercial and U.S. Department of Defense flights. A family of Shuttle-derived In-line vehicles is compared against a family designed around a vehicle optimized for large (250t) payloads. The analysis is performed within the context of an entire space transportation architecture. The goal is to determine which architecture best captures the required missions most cost-effectively. Results indicate that, for the particular mission model analyzed, neither option is clearly superior across the entire payload range. The Shuttle-derived family displays a better evolutionary path for supporting the total mission model (CNDB plus SEI missions). It also reduces earth-to-orbit (ETO) peak funding by 20 percent. The architecture incorporating the Heavy Lift ETO family minimizes SEI program cost and on-orbit operations but is subject to greater schedule risk because of the need for concurrent ETO core and engine development.

Eimers, Dan R.↗
NASA NTRS1990

Lunar vehicle assembly and processing on Space Station Freedom

A concept is proposed that permits the accommodation of lunar vehicles on Space Station Freedom (SSF) within the context of the Human Exploration Initiative. The facility required for lunar-vehicle processing is defined with references to the types of support equipment assumed for these tasks. Attention is given to the SSF Assembly Complete, verification of the Lunar Transfer Vehicles (LTVs), and the attachments of reusable vs expendable LTVs. The impact of the assembly and processing operations is delineated with specific qualifications for revising the allowances for vehicle mass and controllability, reboost fuel needs, microgravity activities, and flight attitude. EVA working time is estimated for overhead and truss-assembly operations at about 3 months to support reusable LTV operations on the SSF. An Assembly/Servicing Facility is proposed for these activities with specific hardware options, and a hydrogen-oxygen propulsion system is proposed to make these activities more efficient.

Troutman, Patrick A.↗
NASA NTRS1992

Surface transport vehicles and supporting technology requirements

Requirements have been identified for surface transport vehicles which allow remote scientific exploration on the moon, as well as lunar resource recovery and emplacement of a permanent base on the lunar surface. Attention is given to the results of a design study which developed configurational concepts for lunar surface transport vehicles and inferred technology-development requirements, with a view to a phased program of implementation. Distinct benefits are noted for the design of simple vehicle platforms with high commonality, in order to reduce logistical-support requirements and maximize functional flexibility. Two generic vehicle classed are defined.

Matijevic, J. R.↗
NASA NTRS1991

Optimization of vehicle weight for Mars excursion missions

The excursion class mission to Mars is defined as a mission with one year durations coupled with a stay time of up to 30 days. The fuel budget for such a mission is investigated. The overall figure of merit in such an assessment is the vehicle weight ratio, the ratio between the wet vehicle weight to the dry vehicle weight. It is necessary to minimize the overall fuel budget for the mission in order to maximize the benefits that could be obtained by sending humans to Mars. Assumptions used in the analysis are: each mission will depart and terminate in low-earth-orbit (LEO) (500 km circular) and the maximum stay time at Mars is 30 days. The maximum mission duration is one year (355-375 days). The mass returned to LEO is 135,000 kg, the dropoff mass left at Mars is 168,000 kg. Three propulsive techniques for atmospheric interface are investigated: aerobraking, all-chemical propulsion, and nuclear thermal propulsion. By defining the fuel requirements, the space transfer vehicle's configuration is defined.

Ferebee, Melvin J., Jr.↗
NASA NTRS1992

An adaptive grid method for computing the high speed 3D viscous flow about a re-entry vehicle

An algebraic solution adaptive grid generation method that allows adapting the grid in all three coordinate directions is presented. Techniques are described that maintain the integrity of the original vehicle definition for grid point movement on the vehicle surface and that avoid grid cross over in the boundary layer portion of the grid lying next to the vehicle surface. The adaptive method is tested by computing the Mach 6 hypersonic three dimensional viscous flow about a proposed Martian entry vehicle.

Bockelie, Michael J.↗