Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TUBING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Radiative cooling of a hydrogen plasma in a shock tube

A method of computing radiative cooling of a hydrogen plasma assuming quasi-isothermal radiative transfer is described. A comparison with nonisothermal calculations for a plane parallel slab indicates good agreement for temperature gradients up to 300 K/cm. The calculations are compared with shock-tube data obtained in the JPL high-performance shock-tube facility. The calculations agreed with the data for one run but were 20 percent high for the other. Due to greater radiative cooling at the test slug boundaries a lateral temperature variation typically exists. This would cause the intensity measurement, which is integrated across the diameter of the test slug, to be below the prediction.

Stickford, G. H., Jr.↗

Self-scanned Digicon - A digital image tube for astronomical spectroscopy

We have successfully fabricated, tested, and operated a digital image tube consisting of a magnetically focused image intensifier tube in which a self-scanned linear array of 1024 silicon photodiodes operating in the EBS mode serves as the photoelectron image detector, amplifier, and intermediate image storage device. Integral on-chip MOS shift registers driven by an external clock sequentially interrogate the photodiodes through MOS FET multiplex switch arrays. Each output frame is a sequence of 256 analog pulses on each of four video lines. Laboratory and observing tests show that the output signal is photoelectron shot noise limited over at least a range of 1-100,000 detected photoelectrons per picture element, indicating that single photon detection is achieved. High-resolution astronomical spectroscopy has been carried out in the coude spectrograph of the 2.7-m telescope at McDonald Observatory. Examples are shown.

Tull, R. G.↗

Diffused waveguiding capillary tube with distributed feedback for a gas laser

For use in a waveguide gas laser, a capillary tube of glass or ceramic has an inner surface defining a longitudinal capillary opening through which the laser gas flows. At least a portion of the inner surface is corrugated with corrugations or channels with a periodicity Lambda where Lambda = 1/2 Lambda, Lambda being the laser gas wavelength. The tube includes a diffused region extending outwardly from the opening. The diffused region of a depth d on the order of 1 Lambda to 3 Lambda acts as a waveguide for the waves, with the corrugations producing distributed feedback. The evanescent component of the waves traveling in the diffused region interact with the laser gas in the opening, gaining energy, and thereby amplifying the waves travelling in the diffused region, which exit the diffused region, surrounding the opening, as a beam of wavelength Lambda.

Elachi, C.↗

Flow-establishment times for blunt bodies in an expansion tube

Flow establishment results are presented as obtained from shock standoff distance, pressure, and heat transfer measurements in the Langley expansion tube. The models tested were flat-faced cylinders with varying radius and a sphere with a constant radius, and they were positioned at the acceleration section exit and tested in the open jet at zero angle of attack. The experimental results were obtained as spinoff from various studies using helium, air, and CO2 test gases at freestream velocities in the range 5-7 km/sec. Time histories of shock detachment distance illustrate that the shock formation about the smaller-radii flat-faced cylinders and the sphere is symmetrical, whereas a complex, asymmetric formation is observed for the larger-radii cylinders. Flow is shown to establish more readily about the sphere than a flat-faced cylinder of the same diameter. A quasi-steady flow exists about relatively large blunt models during two-thirds of the approximate 250-microsec expansion tube test period.

Miller, C. G.↗

Absolute measurement of the photoionization cross section of atomic hydrogen with a shock tube for the extreme ultraviolet

The paper reports an experiment which is part of a program to measure the absolute values of the atomic photoionization cross sections of astrophysically abundant elements, particularly in stars and planetary atmospheres. An aerodynamic pressure-driven shock tube constructed from stainless steel with a quadratic cross section was used to measure the photoionization cross section of H I at 19 wavelength points from 910 to 609 A with experimental uncertainties between 7 and 20%. The shock tube was used to produce fully dissociated hydrogen and neon mixtures for the photoabsorption measurements.

Palenius, H. P.↗

Tube-bending scale/protractor

Combination protractor and scale for measuring tube bends has novel pivot that allows tube to remain in contact with scale arms for all bend angles. Device permits rapid and accurate scribing and measurement of mockup fluid lines to obtain production data.

Millett, A. U.↗

Description and operating performance of a parallel-rail electric-arc system with helium driver gas for the Langley 6-inch expansion tube

A parallel-rail arc-discharge system to heat and pressurize the initial helium driver gas of the Langley 6-inch expansion tube is described. This system was designed for a 2.44-m-long driver vessel rated at 138 MPa, with a distance between rails of 20.3 cm. Electric energy was obtained from a capacitor storage system rated at 12,000 V with a maximum energy of 5 MJ. Tests were performed over a range of energy from 1.74 MJ to the maximum value. The operating experience and system performance are discussed, along with results from a limited number of expansion-tube tests with air and carbon dioxide as test gases.

Moore, J. A.↗

Table and charts of equilibrium normal-shock and shock-tube properties for pure carbon dioxide with velocities from 1 to 16 km/sec

Equilibrium thermodynamic and flow properties are presented in tabulated and graphical form for moving, standing, and reflected normal shock waves in pure CO2. Properties include pressure, temperature, density, enthalpy, speed of sound, entropy, molecular weight ratio, isentropic exponent, velocity, and species mole fractions. Incident (moving) shock velocities are varied from 1 to 16 km/sec for a range of initial pressure of 5 N/sq m to 500 kN/sq m. The present results are applicable to shock tube flows and to freeflight conditions for a blunt body at high velocities. Working charts illustrating idealized shock tube performance with CO2 test gas and heated helium and hydrogen driver gases are also presented.

Miller, C. G., III↗

Communications technology satellite output-tube design and development

The design and development of a 200-watt-output, traveling-wave tube (TWT) for the Communications Technology Satellite (CTS) is discussed, with emphasis on the design evolution during the manufacturing phase of the development program. Possible further improvements to the tube design are identified.

Connolly, D. J.↗

Preliminary studies of autoignition and flashback in a premixing-prevaporizing flame tube using Jet-A fuel at lean equivalence ratios

Lean equivalence ratios from 0.3 to 0.7 were observed. Combustor inlet air pressures were varied from 0.54 to 2.5 MPa, combustor inlet air temperatures from 550 to 700 K, and reference velocities from 8 to 35 meters per second. Autoignition delay times ranged from 15 to 100 milliseconds and varied inversely with pressure. The Arrhenius activation energy was 41,840 joules per mole. Temperature rise data were obtained in a long premixing-prevaporizing tube at a pressure of 0.56 MPa. Preflame temperature rise data were a function of equivalence ratio, inlet air temperature, and tube residence time. Significant temperature rise occurred above temperatures of 760 K, with autoignition occurring at 775 K for equivalence ratios greater than 0.47. The reactions were similar to cool-flame phenomena. Flashback velocities were measured at temperatures of 610 and 700 K, pressure of 0.56 MPa, and equivalence ratios from 0.6 to 1. Flashback velocities varied from 30 to 65 meters per second.

Marek, C. J.↗

Photoelectron counting with an image intensifier tube and a self-scanned photodiode array

A self-scanned photodiode array was fiber-optically coupled to an ITT proximity-focused image intensifier tube. It was determined that a single photoelectron event produces 34,000 charge carriers in a photodiode. This charge is only a factor of 2.8 above the rms noise level of the preamplifier used in the tests, but standard charge-sensitive techniques are at least a factor of 12 better. The image tube and photodiode array combination can be packaged in a disk 5.1 cm in diameter and 2.6 cm thick.

Sandel, B. R.↗

A shock tube study of line broadening in a temperature range of 6100 to 8300 K

Line widths of the Ca(II) 3968 A and Na(I) 5890 A resonance lines broadened by electric microfields in a plasma were measured. A pressure-driven shock tube was used as the light source. Radiation from the equilibrium region behind the reflected shock wave was studied using a rapid scanning Fabry-Perot interferometer. Electron and argon atom densities of about 8 x 10 to the 16th and 1 x 10 to the 19th/cu cm, respectively, were achieved at the relatively low temperature of around 7500 K by vaporizing a cesium powder that had been added to the shock tube as a solid aerosol in argon gas. The measured line widths were predominantly Stark broadened by the electrons and ions in the plasma, although Doppler, van der Waals, instrument function and optical depth effects had to be taken into account.

Baur, J. F.↗

Bakeable UHV gate valve for microwave tube experimentation

The performance characteristics and design of an ultrahigh-vacuum (UHV) gate valve intended for experiments on high-power microwave tubes are described. Tests run on the valve indicate open/close cycles can run into the hundreds or thousands without trouble. The valve was baked at 450 C or higher for at least 4 h. Applications of the valve include evaluation of NASA-design multistage depressed collectors for high-power PPM focused helix-type traveling-wave tubes.

Gilmour, A. S., Jr.↗

Noble gases in 60009-60010 drive tube samples - Trapped gases and irradiation history

Concentrations and isotopic composition of noble gases are reported for grain size separates: nine soils from the 60010-60009 double drive tube, two soils from the 60007 drill core section, and surface soil 65501. Data are reported on concentrations of solar wind gases, surface-correlated gases (involving solar wind and lunar atmosphere), surface maturity indices, cosmogenic gases, possible soil mixing, and irradiation by cosmic rays. Good correlation is found between solar wind gases in 60009 soils and such surface maturity indices as petrographic agglutinates, magnetic soil fraction, and fine-grained iron. Cosmogenic He-3, Ne-21, Ar-38, Kr-80, and Xe-126 all display close correlations in the drive tube soils.

Bogard, D. D.↗

Glass tubes for protecting solar cells

Protecting solar cells against environmental effects is accomplished by putting them inside glass tubes instead of hermetically sealing them between pairs of flat glass sheets. If cells are coupled with storage battery integrated into tube, freestanding power source could be built.

Shelpuk, B.↗

Operational experience in the Langley expansion tube with various test gases

A resume' of operating experiences with the Langley Expansion Tube is presented. The driver gas was unheated helium at a nominal pressure of 5000 psi and the majority of the data presented are for air and carbon dioxide test gases. The primary purpose of these data is to illustrate the effects of various parameters on quasi-steady test flow duration, as well as free stream and post-normal shock flow conditions. The discussion shows that the Langley Expansion Tube is an operational facility capable of producing good quality, highly repeatable, quasi-steady flow for test times sufficient to establish flow about blunt axisymmetric and two-dimensional models.

Miller, C. G.↗

Bending and torsional vibrations of open tube booms on spinning spacecraft

The mathematical formulation is presented of the coupled bending and twisting equations of motion for open tube booms in spinning spacecraft. The equations are applicable to a general class of open tube booms whose shear center does not coincide with the centroid of the cross section. The emphasis in this paper is on the treatment of the coupled bending and twisting motions. The equations of motion of the center of mass are provided in other references. The results of a simulation of the bending and twisting motion of a circular cross-section boom having a small longitudinal slot on a spinning spacecraft is provided. The simulation demonstrates that the centrifugal forces will induce twisting motion due to offset shear center.

Juang, J. N.↗

A vacuum tube vee-trough collector for solar heating and air conditioning applications

An analysis is conducted of the performance of a vee-trough vacuum tube collector proposed for use in solar heating and cooling applications. The vee-trough reflector is a triangular sectioned, flat surfaced reflector, whose axis is laid in the East-West direction. A vacuum tube receiver placed at the bottom of the vee-trough collects solar heat most efficiently since convection is completely eliminated. Radiation losses are reduced by use of selective coatings on the absorber. Owing to its high temperature capabilities (300-400 F), the proposed scheme could also be used for power generation applications in combination with an organic Rankine conversion system. It is especially recommended for unattended pumping stations since the reflectors only require reversal once every six months.

Selcuk, M. K.↗