Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Strain engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

800 C Silicon Carbide (SiC) Pressure Sensors for Engine Ground Testing

MEMS-based 4H-SiC piezoresistive pressure sensors have been demonstrated at 800 C, leading to the discovery of strain sensitivity recovery with increasing temperatures above 400 C, eventually achieving up to, or near, 100 recovery of the room temperature values at 800 C. This result will allow the insertion of highly sensitive pressure sensors closer to jet, rocket, and hypersonic engine combustion chambers to improve the quantification accuracy of combustor dynamics, performance, and increase safety margin. Also, by operating at higher temperature and locating closer to the combustion chamber, reduction of the length (weight) of pressure tubes that are currently used will be achieved. This will result in reduced costlb to access space.

Pressure sensors↗
NASA NTRS2016

InSitu SEM Investigation of Microstructural Damage Evolution and Strain Relaxation in a Melt Infiltrated SiC/SiC Composite

With CMC components poised to complete flight certification in turbine engines on commercial aircraft within the near future, there are many efforts within the aerospace community to model the mechanical and environmental degradation of CMCs. Direct observations of damage evolution are needed to support these modeling efforts and provide quantitative measures of damage parameters used in the various models. This study was performed to characterize the damage evolution during tensile loading of a melt infiltrated (MI) silicon carbide reinforced silicon carbide (SiC/SiC) composite. A SiC/SiC tensile coupon was loaded to a maximum global stress of 30 ksi in a tensile fixture within an SEM while observations were made at 5 ksi increments. Both traditional image analysis and DIC (digital image correlation) were used to quantify damage evolution. With the DIC analysis, microscale damage was observed at the fiber-matrix interfaces at stresses as low as 5 ksi. First matrix cracking took place between 20 and 25 ksi, accompanied by an observable relaxation in strain near matrix cracks. Matrix crack opening measurements at the maximum load ranged from 200 nm to 1.5 m. Crack opening along the fiber-matrix interface was also characterized as a function of load and angular position relative to the loading axis. This characterization was funded by NASA GRC and was performed to support NASA GRC modeling of SiC/SiC environmental degradation

testing↗
DOE OSTI2020

A matrix-free approach for finite-strain hyperelastic problems using geometric multigrid

This paper investigates matrix-free algorithms for problems in quasi-static finite-strain hyperelasticity. Iterative solvers with matrix-free operator evaluation have emerged as an attractive alternative to sparse matrices in the fluid dynamics and wave propagation communities because they significantly reduce the memory traffic, the limiting factor in classical finite element solvers. Specifically, we study different matrix-free realizations of the finite element tangent operator and determine whether generalized methods of incorporating complex constitutive behavior might be feasible. Furthermore, in order to improve the convergence behavior of iterative solvers, we also propose a method by which to construct level tangent operators and employ them to define a geometric multigrid preconditioner. Additionally, the performance of the matrix-free operator and the geometric multigrid preconditioner is compared to the matrix-based implementation with an algebraic multigrid (AMG) preconditioner on a single node for a representative numerical example of a heterogeneous hyperelastic material in two and three dimensions. We find that matrix-free methods for finite-strain solid mechanics are very promising, outperforming linear matrix-based schemes by two to five times, and that it is possible to develop numerically efficient implementations that are independent of the hyperelastic constitutive law.

42 ENGINEERING↗
DOE OSTI2013

Metabolic engineering of Caldicellulosiruptor bescii yields increased hydrogen production from lignocellulosic biomass

Background: Members of the anaerobic thermophilic bacterial genus Caldicellulosiruptor are emerging candidates for consolidated bioprocessing (CBP) because they are capable of efficiently growing on biomass without conventional pretreatment. C. bescii produces primarily lactate, acetate and hydrogen as fermentation products, and while some Caldicellulosiruptor strains produce small amounts of ethanol C. bescii does not, making it an attractive background to examine the effects of metabolic engineering. The recent development of methods for genetic manipulation has set the stage for rational engineering of this genus for improved biofuel production. Here, we report the first targeted gene deletion, the gene encoding lactate dehydrogenase (ldh), for metabolic engineering of a member of this genus. Results: A deletion of the C. bescii L-lactate dehydrogenase gene (ldh) was constructed on a non-replicating plasmid and introduced into the C. bescii chromosome by marker replacement. The resulting strain failed to produce detectable levels of lactate from cellobiose and maltose, instead increasing production of acetate and H2 by 21-34% relative to the wild type and pyrFA parent strains. The same phenotype was observed on a real-world substrate switchgrass (Panicum virgatum). Furthermore, the ldh deletion strain grew to a higher maximum optical density than the wild type on maltose and cellobiose, consistent with the prediction that the mutant would gain additional ATP with increased acetate production. Conclusions: Deletion of ldh in C. bescii is the first use of recently developed genetic methods for metabolic engineering of these bacteria. This deletion resulted in a redirection of electron flow from production of lactate to acetate and hydrogen. New capabilities in metabolic engineering combined with intrinsic utilization of lignocellulosic materials position these organisms to provide a new paradigm for consolidated bioprocessing of fuels and other products from biomass.

Biohydrogen↗
DOE OSTI2020

Primal interface debonding formulation for finite strain isotropic plasticity

In this work, a framework is developed for modeling ductile damage of nonlinear materials whose plastic deformation is characterized using rate independent classical plasticity. This method relies on the assumption that the free energy can be decomposed into elastic, plastic and damage parts. A thermodynamically consistent method is derived which satisfies the second law of thermodynamics in the Clausius–Duhem inequality form. The dissipation associated with plasticity takes place in the domain only, while damage dissipation is localized to the interface. The method is developed using Variational Multiscale ideas to obtain definitions of the interface fluxes within a primal formulation analogous to the Discontinuous Galerkin method, which ensures weakly vanishing interface gap prior to reaching a damage initiation criterion. The local nonlinear problem to calculate both plastic deformation gradient and damage variable follows an incremental approach similar to classical plasticity return mapping algorithm. This elastoplastic damage formulation is developed for material undergoing finite strain, and it naturally accommodates a trapezoidal traction separation law (TSL) whose shape can be varied to model either ductile interface behavior or brittle interface behavior. The formulation's performance is assessed through modeling a patch test and a compact tension specimen.

42 ENGINEERING↗
DOE OSTI2015

Analytics for Metabolic Engineering

Realizing the promise of metabolic engineering has been slowed by challenges related to moving beyond proof-of-concept examples to robust and economically viable systems. Key to advancing metabolic engineering beyond trial-and-error research is access to parts with well-defined performance metrics that can be readily applied in vastly different contexts with predictable effects. As the field now stands, research depends greatly on analytical tools that assay target molecules, transcripts, proteins, and metabolites across different hosts and pathways. Screening technologies yield specific information for many thousands of strain variants, while deep omics analysis provides a systems-level view of the cell factory. Efforts focused on a combination of these analyses yield quantitative information of dynamic processes between parts and the host chassis that drive the next engineering steps. Overall, the data generated from these types of assays aid better decision-making at the design and strain construction stages to speed progress in metabolic engineering research.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2018

Topology optimization of finite strain viscoplastic systems under transient loads [Dynamic topology optimization based on finite strain visco-plasticity]

In this paper, a transient finite strain viscoplastic model is implemented in a gradient-based topology optimization framework to design impact mitigating structures. The model's kinematics relies on the multiplicative split of the deformation gradient, and the constitutive response is based on isotropic hardening viscoplasticity. To solve the mechanical balance laws, the implicit Newmark-beta method is used together with a total Lagrangian finite element formulation. The optimization problem is regularized using a partial differential equation filter and solved using the method of moving asymptotes. Sensitivities required to solve the optimization problem are derived using the adjoint method. To demonstrate the capability of the algorithm, several protective systems are designed, in which the absorbed viscoplastic energy is maximized. Finally, the numerical examples demonstrate that transient finite strain viscoplastic effects can successfully be combined with topology optimization.

42 ENGINEERING↗
DOE OSTI2023

Construction and Modeling of a Coculture Microplate for Real-Time Measurement of Microbial Interactions

The dynamic structures of microbial communities emerge from the complex network of interactions between their constituent microorganisms. Quantitative measurements of these interactions are important for understanding and engineering ecosystem structure. Here, we present the development and application of the BioMe plate, a redesigned microplate device in which pairs of wells are separated by porous membranes. BioMe facilitates the measurement of dynamic microbial interactions and integrates easily with standard laboratory equipment. We first applied BioMe to recapitulate recently characterized, natural symbiotic interactions between bacteria isolated from the Drosophila melanogaster gut microbiome. Specifically, the BioMe plate allowed us to observe the benefit provided by two Lactobacillus strains to an Acetobacter strain. We next explored the use of BioMe to gain quantitative insight into the engineered obligate syntrophic interaction between a pair of Escherichia coli amino acid auxotrophs. We integrated experimental observations with a mechanistic computational model to quantify key parameters associated with this syntrophic interaction, including metabolite secretion and diffusion rates. This model also allowed us to explain the slow growth observed for auxotrophs growing in adjacent wells by demonstrating that, under the relevant range of parameters, local exchange between auxotrophs is essential for efficient growth. The BioMe plate provides a scalable and flexible approach for the study of dynamic microbial interactions.

3D printed device↗
NASA NTRS1983

Thin film strain gage development program

Sputtered thin-film dynamic strain gages of 2 millimeter (0.08 in) gage length and 10 micrometer (0.0004 in) thickness were fabricated on turbojet engine blades and tested in a simulated compressor environment. Four designs were developed, two for service to 600 K (600 F) and two for service to 900 K (1200 F). The program included a detailed study of guidelines for formulating strain-gage alloys to achieve superior dynamic and static gage performance. The tests included gage factor, fatigue, temperature cycling, spin to 100,000 G, and erosion. Since the installations are 30 times thinner than conventional wire strain gage installations, and any alteration of the aerodynamic, thermal, or structural performance of the blade is correspondingly reduced, dynamic strain measurement accuracy higher than that attained with conventional gages is expected. The low profile and good adherence of the thin film elements is expected to result in improved durability over conventional gage elements in engine tests.

Grant, H. P.↗
NASA NTRS1993

An engineering model of woven composites based on micromechanics

Composites with three-dimensional woven architectures exhibit large strains to failure when compared to composites made up of the same materials but not with three-dimensional interlocking tows. The fracture mechanics of such three-dimensional architectures is a subject requiring substantial investigation and experimental testing. Classical fracture mechanics concepts (for instance, an isolated defect in a homogeneous body) will not be applicable to the woven fracture test specimen. The use of an isolated singularity to characterize an entire specimen is inadequate when the density of defects is considerable and the material is heterogeneous. Modelling of such a complex system requires a great deal of insight and consideration as well as prudent choices of model sizes to make numerical schemes feasible. The purpose of this manuscript is to review our recently acquired knowledge of damage accumulation in woven composites and to describe a practicable model of the macroscopic behavior in these and other complex composite architectures based on such knowledge. In this manuscript, discussion will be limited to uniaxial compressive loading; considerations of general loading (monotonic and cyclic) will appear in a subsequent manuscript. Our modelling efforts may be briefly described as follows: the composite is subdivided into microstructural elements (microelements) in which the micromechanical modelling is either understood rigorously or can be represented adequately by statistical parameters. There can be microstructural elements for many different types of composite components, such as the various types of warp and weft and matrix for three-dimensional woven composites. The physical dimensions of microelements are made as large as possible while the response within the element can still be represented by a single micromechatlical calculation. The various elements are linked together(sometimes by associating distinct corners and edges, sometimes by superposition) in a pattern which resembles a particular weave architecture. The model can then be loaded in any manner and the linear and nonlinear elastic responses of representative weaves can be calculated. After the elastic regime, the fracture response is determined by monitoring the damage accumulation.

Carter, W. C.↗
NASA NTRS2004

Design and Control of a Proof-of-Concept Active Jet Engine Intake Using Shape Memory Alloy Actuators

The design and control of a novel proof-of-concept active jet engine intake using Nickel-Titanium (Ni-Ti or Nitinol) shape memory alloy (SMA) wire actuators is used to demonstrate the potential of an adaptive intake to improve the fuel efficiency of a jet engine. The Nitinol SMA material is selected for this research due to the material's ability to generate large strains of up to 5 percent for repeated operations, a high power-to-weight ratio, electrical resistive actuation, and easy fabrication into a variety of shapes. The proof-of-concept engine intake employs an overlapping leaf design arranged in a concentric configuration. Each leaf is mounted on a supporting bar that rotates upon actuation by SMA wires electrical resistive heating. Feedback control is enabled through the use of a laser range sensor to detect the movement of a leaf and determine the radius of the intake area. Due to the hysteresis behavior inherent in SMAs, a nonlinear robust controller is used to direct the SMA wire actuation. The controller design utilizes the sliding-mode approach to compensate for the nonlinearities associated with the SMA actuator. Feedback control experiments conducted on a fabricated proof-of-concept model have demonstrated the capability to precisely control the intake area and achieve up to a 25 percent reduction in intake area. The experiments demonstrate the feasibility of engine intake area control using the proposed design.

Song, Gangbing↗
NASA NTRS1980

Investigation of the fuel feed line failures on the Space Shuttle main engine

The Space Shuttle Main Engine (SSME) development program experienced two similar appearing fuel feed line failures during the shutdown portion of two engine tests. Failure investigations into each incident showed that a few cycles of high-amplitude transient strain occurring during the start and cutoff portions of each test could have either accumulated damage and led to a fatigue failure after 46 tests, or caused rupture in a low-strength weld joint. The cause of the high strain was traced to a period of unsteady flow separation during the start and cutoff of each test coincident with the oblique shock approaching the nozzle exit. Since elimination of the flow separation was impractical, the steps taken to allow engine development and flight preparations to continue were: (1) establish the safe operating life of the nozzle, (2) reinforce all low-strength welds, and (3) eliminate the use of thin-wall fuel feed lines. In parallel, the feed line was redesigned and fabrication was initiated on units to be incorporated into the development program.

Larson, E. W.↗
DOE OSTI2022

Examining organic acid production potential and growth‐coupled strategies in Issatchenkia orientalis using constraint‐based modeling

Abstract Growth‐coupling product formation can facilitate strain stability by aligning industrial objectives with biological fitness. Organic acids make up many building block chemicals that can be produced from sugars obtainable from renewable biomass. Issatchenkia orientalis is a yeast strain tolerant to acidic conditions and is thus a promising host for industrial production of organic acids. Here, we use constraint‐based methods to assess the potential of computationally designing growth‐coupled production strains for I. orientalis that produce 22 different organic acids under aerobic or microaerobic conditions. We explore native and engineered pathways using glucose or xylose as the carbon substrates as proxy constituents of hydrolyzed biomass. We identified growth‐coupled production strategies for 37 of the substrate‐product pairs, with 15 pairs achieving production for any growth rate. We systematically assess the strain design solutions and categorize the underlying principles involved.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2017

In vivo synergistic activity of a CAZyme cassette from Acidothermus cellulolyticus significantly improves the cellulolytic activity of the C. bescii exoproteome

The use of microbial cells to convert plant biomass directly to fuels and chemicals is referred to as consolidated bioprocessing (CBP). Members of the bacterial genus, Caldicellulosiruptor (Gram-positive, anaerobic hyperthermophiles) are capable of deconstructing plant biomass without enzymatic or chemical pretreatment. This is accomplished by the production and secretion of free, multi-domain enzymes that outperform commercial enzyme cocktails on some substrates. Here, we show that the exoproteome of C. bescii may be enhanced by the heterologous expression of enzymes from Acidothermus cellulolyticus that act synergistically to improve sugar release from complex substrates; as well as improve cell growth. In this work, co-expression of the A. cellulolyticus Acel_0615 ..beta..-glucanase (GH6 and GH12) and E1 endoglucanase (GH5) enzymes resulted in an increase in the activity of the exoproteome on Avicel; as well as an increase in growth of C. bescii on Avicel compared to the parental strain or the strain expressing the ..beta..-glucanase alone. As a result, our ability to engineer the composition and effectiveness of the exoproteome of these bacteria provides insight into the natural mechanism of plant cell wall deconstruction, as well as future directions for improving CBP.

09 BIOMASS FUELS↗
DOE OSTI2026

All You Can Eat Yeast: Substituting Hexose Transporters With AtSWEET7 Alleviates Glucose Repression, Enabling Simultaneous Utilization of Sugars in Renewable Feedstocks

Yeast sugar transporters have highly evolved for preferential glucose transport, a significant roadblock for utilizing non-glucose sugars in renewable feedstocks such as lignocellulosic biomass. To enable simultaneous transport of multiple sugars, native hexose transporters were replaced by SWEET7p from Arabidopsis thaliana in engineered Saccharomyces cerevisiae capable of fermenting xylose. Engineered S. cerevisiae exhibited reduced glucose preference, simultaneously co-fermenting glucose, mannose, fructose, and xylose both in synthetic and industrial media. Continuous culture experiments demonstrated the co-consuming phenotype and alleviation of glucose repression by engineered S. cerevisiae. In addition to hexose and pentose, the NKSW7-1 strain consumed xylitol as a carbon source. Through transcriptomic and metabolomic analysis of the NKSW7-1 strain, we show that the replacement of HXT1-7 with AtSWEET7 led to systemwide reprogramming of the central carbon metabolism. This broad transport capacity of AtSWEET7p holds promise for achieving co-consumption of all sugars in underutilized renewable feedstocks by microbial cell factory.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2018

Flaw characterization and correlation with cracking strength in Engineered Cementitious Composites (ECC)

Engineered Cementitious Composite (ECC) is a class of fiber reinforced composites showing strain hardening behavior. The variation of cracking strength among various sections of a tensile specimen is a key factor governing the cracking behaviors of ECC. This study employs X-ray computed tomography method to investigate the correlation between cracking strength and flaw distribution in ECC, and identifies the dimensions of pre-existing flaws to be the main influencing parameters. Specifically, the largest cross-sectional area of a flaw perpendicular to stress can be well correlated with cracking strength. To validate the observation, the classic model on first crack strength is modified in this study by adopting a refined fiber bridging relation and employing iterated crack profile. The simulated cracking strength vs flaw size relation is in good agreement with test results. This study provides an improved understanding of the multiple cracking mechanism in ECC, which is useful for material design.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Data-driven surrogates for high dimensional models using Gaussian process regression on the Grassmann manifold

This paper introduces a surrogate modeling scheme based on Grassmannian manifold learning to be used for cost-efficient predictions of high-dimensional stochastic systems. The method exploits subspace-structured features of each solution by projecting it onto a Grassmann manifold. This point-wise linear dimensionality reduction harnesses the structural information to assess the similarity between solutions at different points in the input parameter space. The method utilizes a solution clustering approach in order to identify regions of the parameter space over which solutions are sufficiently similarly such that they can be interpolated on the Grassmannian. In this clustering, the reduced-order solutions are partitioned into disjoint clusters on the Grassmann manifold using the eigen-structure of properly defined Grassmannian kernels and, the Karcher mean of each cluster is estimated. Then, the points in each cluster are projected onto the tangent space with origin at the corresponding Karcher mean using the exponential mapping. For each cluster, a Gaussian process regression model is trained that maps the input parameters of the system to the reduced solution points of the corresponding cluster projected onto the tangent space. Using this Gaussian process model, the full-field solution can be efficiently predicted at any new point in the parameter space. In certain cases, the solution clusters will span disjoint regions of the parameter space. In such cases, for each of the solution clusters we utilize a second, density-based spatial clustering to group their corresponding input parameter points in the Euclidean space. The proposed method is applied to two numerical examples. Here, the first is a nonlinear stochastic ordinary differential equation with uncertain initial conditions where the surrogate is used to predict the time history solution. The second involves modeling of plastic deformation in a model amorphous solid using the Shear Transformation Zone theory of plasticity, where the proposed surrogate is used to predict the full strain field of a material specimen under large shear strains.

42 ENGINEERING↗