Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Theoretical performance of solar cell based on mini-bands quantum dots

The tremendous amount of research in solar energy is directed toward intermediate band solar cell for its advantages compared with the conventional solar cell. The latter has lower efficiency because the photons have lower energy than the bandgap energy and cannot excite mobile carriers from the valence band to the conduction band. On the other hand, if mini intermediate band is introduced between the valence and conduction bands, then the smaller energy photons can be used to promote charge carriers transfer to the conduction band and thereby the total current increases while maintaining a large open circuit voltage. In this article, the influence of the new band on the power conversion efficiency for structure of quantum dots intermediate band solar cell is theoretically investigated and studied. The time-independent Schrödinger equation is used to determine the optimum width and location of the intermediate band. Accordingly, achievement of a maximum efficiency by changing the width of quantum dots and barrier distances is studied. Theoretical determination of the power conversion efficiency under the two different ranges of QD width is presented. From the obtained results, the maximum power conversion efficiency is about 70.42%. It is carried out for simple cubic quantum dot crystal under fully concentrated light. It is strongly dependent on the width of quantum dots and barrier distances.

14 SOLAR ENERGY↗

High Radiation Resistance IMM Solar Cell

Due to high launch costs, weight reduction is a key driver for the development of new solar cell technologies suitable for space applications. This project is developing a unique triple-junction inverted metamorphic multijunction (IMM) technology that enables the manufacture of very lightweight, low-cost InGaAsP-based multijunction solar cells. This IMM technology consists of indium (In) and phosphorous (P) solar cell active materials, which are designed to improve the radiation-resistant properties of the triple-junction solar cell while maintaining high efficiency. The intrinsic radiation hardness of InP materials makes them of great interest for building solar cells suitable for deployment in harsh radiation environments, such as medium Earth orbit and missions to the outer planets. NASA Glenn's recently developed epitaxial lift-off (ELO) process also will be applied to this new structure, which will enable the fabrication of the IMM structure without the substrate.

Pan, Noren↗

High Efficiency Inverted GaAs and GaInP/GaAs Solar Cells With Strain-Balanced GaInAs/GaAsP Quantum Wells

High-efficiency solar cells are essential for high-density terrestrial applications, as well as space and potentially vehicle applications. The optimum bandgap for the terrestrial spectrum lies beyond the absorption range of a traditional dual junction GaInP/GaAs cell, with the bottom GaAs cell having higher bandgap energy than necessary. Lower energy bandgaps can be achieved with multiple quantum wells (QWs), but such a pathway requires advanced management of the epitaxial growth conditions in order to be useful. Strain-balanced GaAsP/GaInAs QWs are incorporated into a single junction GaAs solar cell and a dual junction GaInP/GaAs solar cell, leading to 27.2% efficiency in the single junction device and a one-sun record 32.9% efficiency in the tandem device. Good carrier collection and low non-radiative recombination are observed in the cells with up to 80 QWs. The GaAs cells employ a rear-heterojunction architecture to boost the open-circuit voltage to over 1.04 V in the quantum well device, despite the large number of QWs.

14 SOLAR ENERGY↗

CO2 laser annealing of 50-microns-thick silicon solar cells

A test program is conducted to determine thin solar cell annealing effects using a laser energy source. A CO2 continuous-wave laser was used in annealing experiments on 50 micrometers-thick silicon solar cells after proton irradiation. Test cells were irradiated to a fluence of 1.0 x 10 to the 12th power protons/sq cm with 1.9 MeV protons. After irradiation, those cells receiving full proton dosage were degraded by an average of 30% in output power. In annealing tests laser beam exposure times on the solar cell varied from 2 seconds to 16 seconds reaching cell temperatures of from 400 C to 500 C. Under those conditions annealing test results showed recovery in cell output power of from 33% to 90%.

Walker, F. E.↗

A theoretical study of heterojunction and graded band gap type solar cells

A computer program was designed for the analysis of variable composition solar cells and applied to several proposed solar cell structures using appropriate semiconductor materials. The program simulates solar cells made of a ternary alloy of two binary semiconductors with an arbitrary composition profile, and an abrupt or Gaussian doping profile of polarity n-on-p or p-on-n with arbitrary doping levels. Once the device structure is specified, the program numerically solves a complete set of differential equations and calculates electrostatic potential, quasi-Fermi levels, carrier concentrations and current densities, total current density and efficiency as functions of terminal voltage and position within the cell. These results are then recorded by computer in tabulated or plotted form for interpretation by the user.

Sutherland, J. E.↗

In-depth analysis of chloride treatments for thin-film CdTe solar cells

CdTe thin-film solar cells are now the main industrially established alternative to silicon-based photovoltaics. These cells remain reliant on the so-called chloride activation step in order to achieve high conversion efficiencies. Here, by comparison of effective and ineffective chloride treatments, we show the main role of the chloride process to be the modification of grain boundaries through chlorine accumulation, which leads an increase in the carrier lifetime. It is also demonstrated that while improvements in fill factor and short circuit current may be achieved through use of the ineffective chlorides, or indeed simple air annealing, voltage improvement is linked directly to chlorine incorporation at the grain boundaries. Lastly, this suggests that focus on improved or more controlled grain boundary treatments may provide a route to achieving higher cell voltages and thus efficiencies.

14 SOLAR ENERGY↗

Improving Solar Cells With Polycrystalline Silicon

In proposed solar-cell design, layers of polycrystalline silicon grown near front metal grid and back metal surface. Net electrical effect increases open-circuit voltage and short-circuit current, resulting in greater cell power output and energy conversion efficiency. Solar-cell configuration differs from existing one in that layers of doped polycrystalline silicon added to reduce recombination in emitter and back surface field regions.

Rohatgi, Ajeet↗

N-Butyl acrylate polymer composition for solar cell encapsulation and method

A polymer syrup for encapsulating solar cell assemblies. The syrup includes uncrosslinked poly(n-butyl)acrylate dissolved in n-butyl acrylate monomer. Preparation of the poly(n-butyl)acrylate and preparation of the polymer syrup is disclosed. Methods for applying the polymer syrup to solar cell assemblies as an encapsulating pottant are described. Also included is a method for solar cell construction utilizing the polymer syrup as a dual purpose adhesive and encapsulating material.

Gupta, Amitava↗

Improving Silicon Solar Cell Efficiency Through Advanced Cell Processing, Highly Uniform Texturing, and Thinner Cells

This CRADA is aimed at developing silicon solar cell technologies that can yield higher efficiency solar cells. Specifically, this CRADA cover three technologies: (i) developing a high temperature process for dissolution of oxygen precipitates, (ii) uniform texturization of diamond wire sawn wafers, and (iii) evaluation of techniques to bond techniques thin wafers and thin films.

14 SOLAR ENERGY↗

Defects and annealing studies in 1-Me electron irradiated (AlGa)As-GaAs solar cells

The deep-level defects and recombination mechanisms in the one-MeV electron irradiated (AlGa)As-GaAs solar cells under various irradiation and annealing conditions are discussed. Deep-level transient spectroscopy (DLTS) and capacitance-voltage (CV) techniques were used to determine the defect and recombination parameters such as energy levels and defect density, carrier capture cross sections and lifetimes for both electron and hole traps as well as hole diffusion lengths in these electron irradiated GaAs solar cells. GaAs solar cells used in this study were prepared by the infinite solution melt liquid phase epitaxial (LPE) technique at Hughes Research Lab., with (Al0.9Ga0.1)-As window layer, Be-diffused p-GaAs layer on Sn-doped n-GaAs or undoped n-GaAs active layer grown on n(+)-GaAs substrate. Mesa structure with area of 5.86x1000 sq cm was fabricated. Three different irradiation and annealing experiments were performed on these solar cells.

Li, S. S.↗

Screen-Printed Contacts for Crystalline Silicon Solar Cells: An Overview

Over the years, the photovoltaic market, worldwide, has been witnessing a double-digit growth rate. The silicon solar cell manufacturing technology has evolved to utilize raw materials optimally to address this growth. One of the ways in which manufacturers are addressing the challenge is by increasing the cell size and making thinner wafers. With this change in parameters, understanding the metal contact formation in solar cells becomes paramount to improve their efficiency. Screen printing is a widely used method to form metal contacts on solar cells and is ideally suited for large-volume manufacturing. This paper presents a review of the (a) role of screen printing in various solar cell architectures and (b) existing models for current conduction and contact formation mechanisms. An alternate approach to current conduction and contact formation mechanism in silicon solar cells is proposed.

contacts↗

A Physics-Based Analytical Model for Perovskite Solar Cells

Perovskites are promising next-generation absorber materials for low-cost and high-efficiency solar cells. Although perovskite cells are configured similar to the classical solar cells, their operation is unique and requires development of a new physical model for characterization, optimization of the cells, and prediction of the panel performance. Here, we develop such a physicsbased analytical model to describe the operation of different types of perovskite solar cells, explicitly accounting for nonuniform generation, carrier selective transport layers, and voltage-dependent carrier collection. Lastly, the model would allow experimentalists to characterize key parameters of existing cells, understand performance bottlenecks, and predict performance of perovskite-based solar panel—the obvious next step to the evolution of perovskite solar cell technology.

14 SOLAR ENERGY↗

Electrical properties and surface morphology of electron beam evaporated p-type silicon thin films on polyethylene terephthalate for solar cells applications

One way to realize low-cost thin film silicon (Si) solar cells fabrication is by depositing the films with high-deposition rate and manufacturing-compatible electron beam (e-beam) evaporation onto inexpensive foreign substrates such as glass or plastic. Most of the ongoing research is reported on e-beam evaporation of Si films on glass substrates to make polycrystalline solar cells but works combining both e-beam evaporation and plastic substrates are still scarce in the literature. This paper studies electrical properties and surface morphology of 1 µm electron beam evaporated Al-doped p-type silicon thin films on textured polyethylene terephthalate (PET) substrate for application as an absorber layer in solar cells. In this work, Si thin films with different doping concentrations (including an undoped reference) are prepared by e-beam evaporation. Energy dispersion X-ray (EDX) showed that the Si films are uniformly doped by Al dopant atoms. With increased Al/Si ratio, doping concentration increased while both resistivity and carrier mobility of the films showed opposite relationships. Root mean square (RMS) surface roughness increased. Overall, the Al-doped Si film with Al/Si ratio of 2% (doping concentration = 1.57×10{sup 16} atoms/cm{sup 3}) has been found to provide the optimum properties of a p-type absorber layer for fabrication of thin film Si solar cells on PET substrate.

36 MATERIALS SCIENCE↗

A computer analysis of heterojunction and graded composition solar cells

The development and application of a variable composition solar cell computer analysis program is discussed. The basic device equations are derived and results of the computer analysis of several Al(x)Ga(1-x)As and GaAs(1-x)P(x) solar cell structures are presented along with a discussion of the effects of interface states and various composition and doping profiles on maximum solar cell efficiency. Interface states are found to be responsible for a severe reduction in the efficiency of GaAs(1-x)P(x) cells, but do not significantly affect the behavior of Al(x)Ga(1-x)As cells. The depth of the p-n junction below the wide bandgap window layer is a critical factor in determining the loss of minority carriers to interface recombination at the heterojunction.

Sutherland, J. E.↗

Nickel contacts for low cost solar cells

It is noted that nickel metallization of silicon solar cells offers a relatively inexpensive method of making electrical contact with the surface of the cell. More expensive methods, involving precious metals and costly processes, are widely used; these have been developed for space applications, where considerations of reliability predominate over those of cost. Since recent interest in terrestrial applications of solar cells has led to an increased concern over cost, nickel has assumed a position as a major candidate for solar cell metallization. It is shown that sintering can improve the integrity of the nickel-silicon bond. Evidence that the nickel-silicon contact can survive moderate environmental stress is presented.

Anderson, J. R.↗

Performance of III–V Solar Cells Grown on Reformed Mesoporous Ge Templates

We demonstrate a solar cell on reformed porous Ge with an efficiency of 7.7%. We generate mesopores in (100) Ge by bipolar electrochemical etching and anneal them at high temperature. The pores coalesce deep in the structure rather than at the surface as desired, although resulting in coarse superficial morphology unsuitable for device growth. To combat this issue, we developed a surface treatment involving an HBr dip, annealing at 415 degrees C, and a postannealing ultrasonic De-ionized water dip to improve the surface structure, resulting in a smoother reformed surface on which we grow a GaInAs solar cell. The structure retains embedded pores after growth and the transitions between Ge and III-V layers are distinct. The solar cell fabricated using the improved coalescence has an efficiency of 4.5%. The efficiency improves to 7.7% by isolating the rest of the device from three limiting localized shunt areas. Protruding defects in the porous Ge and III-V layers still limit the performance, but this work establishes a step toward the technical viability of this exfoliation approach, showing decent efficiency if protruding defects can be removed or reduced.

14 SOLAR ENERGY↗