Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STIRRING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Fabrication of Advanced Nanocarbon-Metal Composites for Improved Energy Efficiency

We fabricated nanocarbon metal composites (NCMC) of Al alloys with a process called “electrocharging assisted process” (EAP). This method consists of the application of a high current to a mixture of liquid metal and carbon particles. We investigated aluminum alloys (6061 and 1350) and used activated carbon and graphite powder as the source of carbon. The high current induces the formation of carbon chains and ribbons in the liquid metal. Upon solidification of the metal an epitaxial relation between the carbon nanostructures and the metal lattice is produced. The purpose of the project was to find the parameters during the reaction that would give rise to a high density of nanoribbons extending throughout the metal such that the electrical conductivity and the mechanical strength of the composite increased and that the method could be extended to large scale manufacturing. For this purpose, we designed two reactors for the incorporation of nanocarbon ribbons in aluminum metal. The first reactor was designed to have more control of the region with the high current density. However, there were problems with getting good mixing of the carbon in small volumes. A second reactor was designed with a stirrer that allowed for better mixing of the carbon by the introduction of argon gas through the shaft of the stirrer. NCMC were fabricated with a series of parameters to understand the role of current, time of applied current, type and shape of the cathode electrode and stirring speed of the mixture. We analyzed the composites by Raman scattering to gain information on the crystallite size of the nanocarbon, XRD to obtain the crystal structure of the composite, SEM and TEM to characterize the grain size of the aluminum grains and the quality of the crystal structure. We also measured the electrical conductivity and mechanical properties of selected samples. The nanocomposites showed increase in crystallite size of the nanocarbon with a linear dependence of the crystallite size on the duration of the applied current. There is a minimum current density necessary for the crystallite size to increase compared to the ~ 10 nm size of the activated carbon source used in the fabrication. The electrical conductivity of the nanocomposites increased with crystallite size of the nanocarbon and with the concentration of converted carbon. The maximum increase in electrical conductivity was 5.7% above the baseline for samples with ~ 4 wt % nanocarbon with crystallite size larger than 30 nm. These samples presented a hardness ~ 8% higher than the baseline samples with no carbon.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Evaluation of Expansion in ETF Grout Compositional Variants

In summary, the Base Case grout, Mix K, prepared according to the protocol provided (short stirring time after struvite precipitation of about 30 minutes) expanded when cured in a dry and damp sealed bag. Two variants, Mix M, 100 % slag in the dry mix, did not expand when prepared and cured under the same dry and damp conditions. Mix L, precipitated struvite removed, showed very slight expansion after curing 289 days for both dry and damp curing which was expressed as slight bulging at the bottom of the container. Mix N, 100 % dilution of the simulant, did not expand when cured under dry conditions or in a sealed container in damp conditions. However, a cylinder of Mix N cured in a container that was slit and taped back together did expand in damp conditions. This condition enabled the grout to be exposed to more moisture that the grout sample cured in the capped container and stored in the same zip top bag with the damp towel. This information is provided to support processing and containerization of the ETF ammonia grout.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Improving the representation of isopycnal mixing in E3SM (Final Report)

The DOE-supported Energy Exascale Earth System Model (E3SM) is a major attempt by the Department of Energy to develop a new Earth System Model using unstructured grids, which allow for the model to concentrate resolution where it is most needed and avoid numerical artifacts experienced by previous Earth System Models (ESMs) using regular grids in which the lateral resolution becomes extremely fine as the resolution shrinks at the poles. This effort required rewriting many of the algorithms previously developed for regular grids. One algorithm that was problematic in the first version of E3SM was the representation of mixing due to turbulent ocean eddies with scales smaller than the model grid. These mesoscale eddies are the primary way by which tracers are stirred along density surfaces in the ocean interior. In particular, the process of isopycnal mixing exchanges fresher, more oxygenated waters from polar regions with saltier, nutrient-rich and oxygen poor waters from tropical regions. Previous work in our group has shown that this mechanism is vitally important for bringing oxygen into poorly ventilated tropical regions (Gnanadesikan et al., 2012, 2013) and plays a significant role in determining the uptake of anthropogenic carbon dioxide (Gnanadesikan et al., 2015). However, in E3SMv1 this process was turned off, as turning it on caused the model to become unstable. Additionally, the rate of isopycnal mixing is directly proportional to a mixing coefficient $A_{Redi}$ whose value varies from less than 400 m 2 /s to 2000 m 2 /s across contemporary climate models. The main thrusts of this proposal therefore were to: 1.) Improve the numerics of isopycnal mixing in E3SM; 2.) Identify ways in which climate models are sensitive to the isopycnal mixing coefficient; and 3.) Develop better representations of the isopycnal mixing coefficient.

54 ENVIRONMENTAL SCIENCES↗

The Recovery of Medical Isotope 188 W from Irradiated W Metal Target - A New Approach

Tungsten-188 is in widespread use in 188 W(t 1/2 = 69 d )/ 188 Re(t 1/2 = 16.9 h ) biomedical generators. Oak Ridge National Laboratory has been providing this product to the world since 1999. At ORNL, 188 W is produced via irradiation in ORNL’s High Flux Isotope Reactor (HFIR). Enriched 186 W targets in the form of sintered metallic pellets or rings achieve a compact loading in the irradiation vessel, providing a high yield per unit target. The enrichment of the target is >90% 186 W, and this isotope undergoes double neutron capture to produce the desired 188 W product. While 188 W is produced by neutron bombardment, 191 Os(t 1/2 = 15.4 d ) is simultaneously produced as a by-product and expected to be separated from 188 W by postirradiation treatment.In the current processing pathway, the irradiated W metal rings are first converted into an oxide form of WO 3 by heating the irradiated W metal target at 750°C in a quartz reaction vessel inside a vertical furnace under a constant flow of air. During heating, W metal reacts with oxygen in the air to produce WO 3 , which is soluble in 6 M NaOH for preparation of 188 W product. This oxidation process also converts 188 Os (the decay daughter of 188 W) and 191 Os (15.4 d , the irradiation produced byproduct) into OsO 4 , a highly volatile and toxic gas. The gaseous effluents driven from the quartz reaction vessel are passed through a scrubbing array to remove OsO 4 before the air is discharged from the process. This heterogeneous oxidation method simultaneously achieves goals of (1) converting metal target to a soluble oxide form and (2) removing volatile OsO 4 away from the solid WO 3 product by air flow and absorbing the harmful Os species by the scrubbing array. But this method has two potential problems as well: (1) O 2 reacts with only W metal at high temperatures, not with W alloyed with other elements. The O 2 –W reaction will be retarded when formation of WRe or WC occurs, or even when a layer of non-W materials on the surface of the irradiated W rings.; (2) 100% absorption of OsO 4 of high yield (>90%) from the reaction of Os + O 2 is a strict requirement to the OsO 4 scrubbing system--so NaOH scrubbers of a redundant size (2x 1.5 L) are in use for safety reasons.To resolve above two potential problems, direct dissolution of the irradiated W metal target by a selected reagent is a preferred pathway to avoid heating step with generation of tremendous amount of volatile OsO 4 . Hydrogen peroxide (H 2 O 2 ) is such a candidate to dissolve W in forms of either metal or alloys, although literature lacks information of solubilities of Re or Os in H 2 O 2 . With experimental results of dissolving non-radioactive W, Re and Os in H 2 O 2 under various conditions, this report illustrates a method of H 2 O 2 dissolution for irradiated W target, with a complete dissolution of W and Re, but ≤10% dissolution of Os (converted into gaseous OsO 4 and carried out into a scrubbing for absorption) during processing irradiated W target. The portion of undissolved Os can be separated from W solution by a follow up filtration step. Solubilities of W, Re and Os in H 2 O 2 at a temperature range from 14° to 50°C are presented. And a dissolution rate of W metal per surface area of W metal in H 2 O 2 is calculated based on results of dissolving a W metal cylinder of known surface area in H 2 O 2 at room temperature without stirring.

07 ISOTOPE AND RADIATION SOURCES↗

Sound Speed as a Candidate for Internal Temperature Monitoring During Solid Phase Processing of Materials

Internal temperature is an important parameter for understanding the solid phase processing (SPP) of materials and improving feedback control of these processes. Friction stir processes, shear assisted processing and extrusion (ShAPE ™ ), and ultrahigh velocity (UHV) cold spray are examples of such processes. Simple thermal models based on temperatures measured at the boundary of the deforming body cannot capture the dynamic nature of temperature generation within the deforming solid. One possibly way of understanding internal temperature is by measuring sound speed, which varies as a function of temperature for materials and directing ultrasonic wave propagation through selected material volumes of interest. In this project, longitudinal wave speed is estimated for aluminum 6061. Piezoelectric materials bonded to a specimen provided data from which longitudinal wave speed was estimated. A discussion evaluated the linear relationship of wave speed versus temperature and postulated how wave speed measurements could be used to estimate the internal temperature of selected material volumes for feedback during SPP of materials. Instrumentation, data and analysis, and a discussion are reviewed.

36 MATERIALS SCIENCE↗

Sparse Data Machine Learning Integration with Theory, Experiment and Uncertainty Quantification: Process-Structure-Property-Performance of Friction Deformation Processing

Computer vision and deep learning tools that advance the ability to establish processing-structure-property-performance (PSPP) relations are presented. The Bayesian binning method for image segmentation enables quantitative analysis of microstructural features in an automated way, while the analysis of shapes and relative orientation of these features reveals local deformation maps indicative of both, material flow and residual stresses due to materials processing. The deep learning method leads to the previous knowledge agnostic mapping of empirically observed microstructural zones in friction stir welding (FSW) process and synthetic microstructure generation capability that is statistically equivalent to experimentally collected data.

97 MATHEMATICS AND COMPUTING↗

Solid Phase Gradient Alloying Method via ShAPE

Alloying has been used to confer desirable properties to various metallic systems since the bronze age. For example, Ni, Mn, and Cr are alloyed into an Fe matrix to make steel, which has improved strength and corrosion resistance (as displayed in Fig. 1). In addition to the type of alloying elements, the amount of alloying elements added into a matrix is also very critical for a material’s mechanical property, physical property, machinability, and cost. Conventionally, new alloys are discovered by combining alloy precursors and elemental constituents into a mixture and melting them together. The solidified product or ingot represents a usually non-homogeneous combination of the chemistry with a microstructure dictated by the physics of solidification. It is time and energy intensive to optimize the alloying amounts via the casting process and hence, economically not conducive to rapid alloy discovery. In addition, the cast microstructure seen in the as-cast ingot is often not the ideal, nor even desired structure for optimized performance. Cast materials often need further processing such as homogenization, annealing, and deformation work put in through rolling, forging, extruding, etc. to have favorable microstructures and properties. A faster method to discover new alloy combinations and evaluate them in their worked or processed form is needed. Recently, Laser Engineered Net Shaping was applied to fabricate gradient compositional material for alloy designing. However, the mechanical properties of this gradient alloy were poor due to the existence of impurities, oxidation and cracks that are inherent in the melt-solidification process. Because of these limitations, we propose to use a solid-phase process (ShAPE) to create bulk materials (extrudates) that vary in composition from one end of the extruded solid to the other. Various manufacturing methods for alloy design including conventional casting method, laser based combinatorial method and current solid phase gradient alloying method are displayed and compared in Fig. 2. ShAPE machine and a schematic of ShAPE process are displayed in Fig. 3. Starting material is processed by a rotating and plunging die to form an extrudate. We are proposing through this methodology to invent a new, bulk-scale combinatorial technique. With this novel technique, alloying element can be dissolved into the matrix with a continued gradient without bulk melting. Formation of inter-metallics and defects originating from melt processing can be avoided. In addition, the ShAPE process creates the mixed alloy chemistry, and meanwhile subjects the material to severe plastic strain, which induces the favorable “worked” microstructure. Products from the ShAPE process can be tested in hardness directly providing a path to rapid evaluation of mechanical properties. The ability to create graded structures using friction stir processing (FSP) has been demonstrated, however using the ShAPE process we believe will lead to much faster and higher fidelity results. When combined with high throughput screening methods of physical, mechanical and microstructural property characterization, efficiency and accuracy of alloy design can be significantly improved.

36 MATERIALS SCIENCE↗

Scaled up Process Report – Apparatus and Model

Advanced voloxidation with NO 2 is a proposed process for used nuclear fuel head-end reprocessing scheme that converts UO 2 to higher oxides, and it also converts partitioning volatile fission products into the gas phase, thus facilitating fuel dissolution and actinide recovery. NO 2 voloxidation is being studied on small batches of UO 2 Simfuel, but the real test of process feasibility will be when it is scaled up to work with >100 g of irradiated material. This report discusses the aspects of scale-up that must be considered for NO 2 voloxidation, including development of a stirred reactor to promote agitation of the mixture during processing, online process monitoring, and automation controls. Brief details on parallel efforts are also provided in this report, including (a) demonstration of iodine release from Simfuel made by Spark Plasma Sintering, and (b) development of an order-of-magnitude scale-up to react 100 g of UO 2 Simfuel in a metal reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Yield stress and flow behavior of enzyme liquefied slurries from corn cobs and corn stover pellets

With the increase in population, the world will depend on renewable sources to meet the increasing energy needs. The use of lignocellulosic biomass as a renewable source has been proven efficient for conversion to cellulosic ethanol and capable of contributing to thresholds for energy demand while reducing greenhouse gases by 90% when compared with fossil fuels. However, limitations in feeding and flow within biorefineries is encountered when system plugging occurs due to biomass compaction and a high yield stress for slurries formed during its processing, thereby preventing transport of biomass materials between plant unit operations. In some cases, this leads to unexpected plant shutdowns increasing industrial operational costs. As an alternative, enzyme-assisted liquefaction for slurry creation from corn stover at solids loadings up to 30% is reported in this work. Two different kinds of biomass (pelleted corn stover and cobs) were liquefied in a fed-batch process using commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU or 3 FPU per gram of dry solids in 10 mM sodium citrate buffer solution (pH 4.8). Pellets were fed into a 1 L stirred bioreactor according to a pre-defined fed-batch protocol over the first 5 hours until reaching 30% of solids loading. After 6, 24 and 96 hours, samples were taken and characterized with respect to their sugar composition, rheology and water absorption. Successful slurry creation with dramatically reduced yield stress was achieved for corn stover for both assessed enzymes. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3 FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme. Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU,Celluclast 1.5L) for corn cobs at 24 hours. Yield stress decreased when residence time increased with an enhanced fluidity noted for higher enzyme concentrations. A profile for 6, 24 and 96h of yield stress measurements is presented.

Guitierrez, Diana↗

Enzyme-assisted liquefaction for different fractions of corn stover pellets

With an increase in population, the world will depend on renewable sources to meet the increasing energy needs. The use of lignocellulosic biomass as a renewable source has been proven efficient for conversion to cellulosic ethanol and capable of contributing to thresholds for energy demand while reducing greenhouse gases by 90% when compared with fossil fuels. However, limitations in feeding and flow within biorefineries are encountered when system plugging occurs due to biomass compaction and a high yield stress for slurries formed during its processing. Furthermore, differences in the biomass source present a challenge to the continuity of operations and reliability in the process. This work explores enzyme-assisted liquefaction for solid loadings up to 30% as an alternative for the creation of slurry from two different types of biomass (pelleted corn stover and cobs) that were liquefied in a fed-batch process using commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU/g or 3 FPU/g of dry solids in a 10 mM sodium citrate buffer solution (pH 4.8). Pellets were fed into a 1 L stirred bioreactor according to a predefined fed-batch protocol during the first 5 hours until 30% solid loading was reached. After 6, 24 and 96 hours, samples were taken and characterized with respect to their composition, rheology, and water absorption. Successful slurry creation with dramatically reduced yield stress was achieved for corn stover for both enzymes assessed. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3 FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme. Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU, Celluclast 1.5L) for corn cobs at 24 hours. A profile for 6, 24 and 96h of yield stress measurements and sugar conversion is presented.

Gutierrez, Diana↗

Liquefaction of different corn stover fractions assisted by enzyme-biomass deconstruction

Recalcitrant properties of different sources of lignocellulosic biomass represent challenges in materials processing within a biorefinery, as well as enzyme efficient deconstruction to fermentable sugars. Limitations include lignin derived enzyme inhibitors, enzyme inhibition by hydrolysis products, and resistance to mixing due to rheological properties of lignocellulosic particulates at high solids loadings. Consequently, we examined conditions that might be used to achieve liquid slurries (i.e., liquefaction) at solids loadings of 300 g/L before the material enters the biorefinery through a pretreatment step. This work explores enzyme-assisted liquefaction in a fed-batch process using the commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU/g or 3 FPU/g of dry solids, basis. Corn stover pellets were fed into a 1 L stirred bioreactor containing enzyme solution over a 5-hour period until reaching 30% solids loading (dry wgt / vol basis). After 6, 24 and 96 hours from the start of the run, samples were taken and characterized with respect to their sugar composition, rheology, water absorption and enzyme activity. Slurries with dramatically reduced yield stresses were achieved for corn stover. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme.Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU, Celluclast 1.5L) for corn cobs at 24 hours.A profile based on 6, 24 and 96h of yield stress measurements and sugar conversion is presented. Enzyme activity is measured and the impact of liquefaction on an integrated processing in a biorefinery operation is discussed.

Gutierrez, Diana↗

High Solids Loading Aqueous Slurry Formation of Corn Stover Before Pretreatment in a Fed-batch Bioreactor

With the increase on population the world will depend on renewable sources to meet the increasingly energy needs. Use of lignocellulosic biomass as a renewable source has been proven efficient for conversion to cellulosic ethanol and capable of contributing to achieve the threshold on energy demand while reducing greenhouse gases in 90% when compared with fossil fuels (Wang et al., 2007, 2012). However, the processing of biomass encounters limitations in feeding and flow within biorefineries due to the system plugging by compaction and slurry high yield stress, preventing transport of biomass materials and in some cases unexpected plant shutdowns that results in high operational costs (dos Santos et al., 2021; Ximenes et al., 2021). Different solutions for biomass handling and slurry formation from densified materials like pellets have been studied. Cellulosic biomass residues are typically processed in pretreatment reactors to which acid or base is added (Humbird et al., 2002). Other pretreatments such as liquid hot water (LHW) and steam explosion that act without the addition of chemicals use pressures above the saturation vapor of water, to disrupt biomass structure (Ruiz et al., 2021). Although these methods are widely known, the use of pretreatments like acid digestion and LHW present challenges like waste disposal and could be energy inefficient (Mosier et al., 2005). Alternatively other approaches like enzymatic liquefaction have been applied for biomass transformation into slurries with promising results and without the use of pretreatments (dos Santos et al., 2021). Nevertheless, enzymatic liquefaction implementation faces difficulties due to the recalcitrant properties of biomass, its variability, and the release of enzyme inhibitors. While it has been proven that chemical composition properties in biomass have effects on enzyme inhibition (Huang et al., 2022; Kim et al., 2011; Zhai et al., 2018), hindering the efficiency of the liquefaction, not ample research has been conducted in understanding the physical properties as particle size, porosity, water adsorption retention and their effect in the ability to form a slurry at high solids concentration (Yan et al., 2020). In order to improve lignocellulosic biomass handling and formation of biomass slurries, enzyme assisted liquefaction for slurry creation from corn stover at solids loadings up to 30% is reported in this work. Two different kinds of biomass (pelleted corn stover and cobs) were liquefied in a fed-batch process using commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU or 3 FPU per gram of dry solids in 10 mM sodium citrate buffer solution (pH 4.8). Pellets were fed into a 1 L stirred bioreactor according to a predefined fed-batch protocol over the first 5 hours until reaching 30% of solids loading. After 6, 24 and 96 hours, samples were taken and characterized with respect to their sugar composition, rheology and water absorption. Successful slurry creation with dramatically reduced yield stress was achieved for corn stover for both assessed enzymes. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3 FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme. Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU, Celluclast 1.5L) for corn cobs at 24 hours. Yield stress decreased when residence time increased with an enhanced fluidity noted for higher enzyme concentrations. A profile for 6, 24 and 96h of yield stress measurements is presented.

Gutierrez, Diana↗

NuMI/LBNF Horn and Stripline Welding

Focusing horns for secondary particles are critical components for creating a stable beam of neutrinos. These components need to survive in a harsh environment and withstand high stresses. Extending the lifetime of the horns is critical as spare fabrication takes approximately two years and has many subcomponents with strict quality control. Two key aspects of the fabrication process include the inner conductor CNC TIG welding and the friction stir welding of the stripline pieces. The process for welding requires steps such as sample welding, x-ray imaging, and tensile pull tests. Having a perfect weld retains as much of the original strength of the base metal and reduces the risk of failure. As FNAL ramps up in power to 2.4MW, the lifetime of the horn and stripline will more heavily rely on continuing to have high quality welding procedures and thorough quality assurance.

Orea, Adrian↗

Scale-Up of Lithium Iron & Aluminum Nickelate Advanced Cathode and Fabrication of A Battery Pack Comprising The Same

Global battery manufacturers are increasingly worried about the serious supply chain constraint caused by rapid fluctuations in cobalt prices over the years. We present a novel cobalt-free, nickel-rich layered cathode material called NFA class (LiNixFeyAlzO2) to tackle this challenge. Spherical NFA(OH)2 precursors were successfully synthesized by incorporating Ni, Fe, and Al elements using a co-precipitation reaction in a continuous stirred tank reactor. The LiNFAO2 cathode, composed of LiNi0.85Fe0.05Al0.1O2, was synthesized and analyzed using X-Ray diffraction, Mössbauer spectroscopy, and scanning electron microscopy (SEM). The material's electrochemical behavior was evaluated through various techniques at different lithiation/delithiation states in two voltage ranges. The cobalt-free material exhibits a high capacity of 190 mAh/g at 0.1C within the voltage range of 3V-4.5V, as demonstrated by electrochemical performance evaluations. Rate and cycling evaluations showed good rate capability and cycling stability, with 88% capacity retention after 100 cycles at C/3 within the voltage range of 3V-4.3V. Our research shows the great potential of cobalt-free NFA cathodes as a feasible option for developing cost-effective lithium-ion batteries.

25 ENERGY STORAGE↗

Scale-Up of Lithium Iron & Aluminum Nickelate Advanced Cathode and Fabrication of A Battery Pack Comprising The Same

Global battery manufacturers are increasingly worried about the serious supply chain constraint caused by rapid fluctuations in cobalt prices over the years. We present a novel cobalt-free, nickel-rich layered cathode material called NFA class (LiNixFeyAlzO2) to tackle this challenge. Spherical NFA(OH)2 precursors were successfully synthesized by incorporating Ni, Fe, and Al elements using a co-precipitation reaction in a continuous stirred tank reactor. The LiNFAO2 cathode, composed of LiNi0.85Fe0.05Al0.1O2, was synthesized and analyzed using X-Ray diffraction, Mössbauer spectroscopy, and scanning electron microscopy (SEM). The material's electrochemical behavior was evaluated through various techniques at different lithiation/delithiation states in two voltage ranges. The cobalt-free material exhibits a high capacity of 190 mAh/g at 0.1C within the voltage range of 3V-4.5V, as demonstrated by electrochemical performance evaluations. Rate and cycling evaluations showed good rate capability and cycling stability, with 88% capacity retention after 100 cycles at C/3 within the voltage range of 3V-4.3V. Our research shows the great potential of cobalt-free NFA cathodes as a feasible option for developing cost-effective lithium-ion batteries.

25 ENERGY STORAGE↗

Magnetic Flux Density Measurements Inside the Z Environment Chamber During Warm X-Ray Shots

The peak magnetic flux density was measured as 148.7 T in the axial direction, at a distance of 41 inches from the source. This value is likely accurate as all field components fell within the 3 dB bandwidth of the accompanying balun, with the peak field component at 3.1 kHz. No field structure could be identified during the test series, suggesting the Z-pinch may create a “mode-stirred” EM environment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Assessment of Benefits of Solid-State Advanced Manufacturing Processes for Nuclear Energy Products

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. This overall project provides the U.S. Department of Energy a critical feasibility study comparison of three solid-state processes to other AM processes, thereby providing the feasibility of the solid-state processes examined to manufacture 316H SS and ODS steel components: • Fused-filament fabrication (FFF): This work provides an initial evaluation of the impact of powder morphology and sizes on the FFF process, and the feasibility and adaptability for different material systems, to use FFF for ODS steels and 316 SS. • Shear-assisted processing and extrusion (ShAPE): Specifically for this portion of the project on ShAPE tube forming, the objectives will be to determine the feasibility to direct tube forming of high tensile strength steel tubing, specifically for ODS steel to determine the effect of the patented extrusion process on the dispersoids of the ODS material. Additionally, as often ODS powders are mechanically alloyed and therefore more platelike or angular, this feasibility was to explore the impact on the optimization process and initial feasibility of direct tube forming. • Cold spray and friction stir additive manufacturing as a stretch goal: Bulk and near net shape manufacturing processes for high-temperature, high-strength alloys are needed. Additionally, cold spray techniques can be applied in-situ at the operational level for repair and can provide multiple benefits to the nuclear industry. These tasks aim to provide information to show benefits of cold spray during the full life cycle, namely research and development, product manufacturing, and repair to mention a few key points.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 1

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024). Three distinct rounds of FSP experiments were performed by the experimental team, producing replicate samples utilizing across different nominal processing conditions (Condition IDs) listed in Table 1. The starting material on which FSP was applied was commercially available unprocessed stainless-steel type 316L material. Chosen processing conditions were very diverse, and some were intentionally chosen to produce defects. Several samples experienced tool breakage during experimentation, so a full set of three replicates was not produced for every nominal processing condition.

36 MATERIALS SCIENCE↗