Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHAPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Icing flight research - Aerodynamic effects of ice and ice shape documentation with stereo photography

Aircraft icing flight research was performed in natural icing conditions. A data base consisting of icing cloud measurements, ice shapes, and aerodynamic measurements is being developed. During research icing encounters the icing cloud was continuously measured. After the encounter, the ice accretion shapes on the wing were documented with a stereo camera system. The increase in wing section drag was measured with a wake survey probe. The overall aircraft performance loss in terms of lift and drag coefficient changes were obtained by steady level speed/power measurements. Selective deicing of the airframe components was performed to determine their contributions to the total drag increase. Engine out capability in terms of power available was analyzed for the iced aircraft. It was shown that the stereo photography system can be used to document ice shapes in flight and that the wake survey probe can measure increases in wing section drag caused by ice. On one flight, the wing section drag coefficient (c sub d) increased approximately 120 percent over the uniced baseline at an aircraft angle of attack of 6 deg. On another flight, the aircraft drag coefficient (c sub d) increased by 75 percent over the uniced baseline at an aircraft lift coefficient (c sub d) of 0.5.

Mikkelsen, K. L.↗

Structural shape optimization - A survey

This paper is a survey of structural shape optimization with an emphasis on techniques dealing with shape optimization of the boundaries of two and three dimensional bodies. Attention is focused on the special problems of structural shape optimization which are due to a finite element model which must change during the optimization process. These problems include the requirement for sophisticated automated mesh generation techniques and careful choice of design variables. They also include special problems in obtaining sufficiently accurate sensitivity derivatives.

Haftka, R. T.↗

Input-current shaped ac to dc converters

The problem of achieving near unity power factor while supplying power to a dc load from a single phase ac source of power is examined. Power processors for this application must perform three functions: input current shaping, energy storage, and output voltage regulation. The methods available for performing each of these three functions are reviewed. Input current shaping methods are either active or passive, with the active methods divided into buck-like and boost-like techniques. In addition to large reactances, energy storage methods include resonant filters, active filters, and active storage schemes. Fast voltage regulation can be achieved by post regulation or by supplementing the current shaping topology with an extra switch. Some indications of which methods are best suited for particular applications concludes the discussion.

Source record↗

Ice shapes and the resulting drag increase for a NACA 0012 airfoil

Experimental measurements of the ice shapes and resulting drag increases were measured in the NASA-Lewis Icing Research Tunnel. The measurements were made over a large range of conditions (e.g., airspeed and temperature, drop size and liquid water content of the cloud, and the angle of attack of the airfoil). The measured drag increase did not agree with the existing correlation. Additional results were given which are helpful in understanding the ice structure and the way it forms, and in improving the ice accretion modeling theories. There are data on the ice surface roughness, on the effect of the ice shape on the local droplet catch, and on the relative importance of various parts of the ice shape on the drag increase. Experimental repeatability is also discussed.

Olsen, W.↗

Shaping of airplane fuselages for minimum drag

The VSAERO surface panel method is employed to investigate fuselage shapes which can enhance the natural laminar flow (NLF) characteristics. The study is performed at cruise Re which are relevant to commuter, transport, and business aircraft. The technique is based on piecewise constant doublet and source singularities and takes into account the effects of compressibility. Inviscid pressure distributions were generated for five configurations to aid in the search for an optimized NLF body shape as a function of the transition locations and the drag coefficients. Granville's transition criteria are incorporated into the calculations to yield shapes with longer runs of laminar flow and reduced drag. In comparison with other transition prediction methods, the method described is shown to have significantly higher valicity for making three-dimensional transition predictions.

Dodbele, S. S.↗

Free boundary shape of a convectively cooled solidified region

The two-dimensional steady-state shape of a solidified region, such as a frost layer, was determined analytically for formation on a plate that is convectively cooled. The nonuniform shape of the layer is produced by exposure to a spatially nonuniform distribution of radiant energy. For high convective cooling the cooled wall approaches a uniform temperature, and an exact solution is obtained for the free boundary shape. For a lesser amount of convective cooling, the variation in temperature along the cooled boundary is treated by a boundary perturbation method. Some illustrative examples are given that show the effects of nonuniform heating and the magnitude of convective heat transfer at the cooled wall. Only one boundary condition is approximated by the perturbation solution; all of the other boundary conditions are satisfied exactly. The calculated results given here were found to satisfy the approximate boundary condition within a very small error.

Siegel, R.↗

Shape optimization including finite element grid adaptation

The prediction of optimal shape design for structures depends on having a sufficient level of precision in the computation of structural response. These requirements become critical in situations where the region to be designed includes stress concentrations or unilateral contact surfaces, for example. In the approach to shape optimization discussed here, a means to obtain grid adaptation is incorporated into the finite element procedures. This facility makes it possible to maintain a level of quality in the computational estimate of response that is surely adequate for the shape design problem.

Kikuchi, N.↗

Geometries for roughness shapes in laminar flow

A passive interface mechanism between upper and lower skin structures, and a leading edge structure of a laminar flow airfoil is described. The interface mechanism takes many shapes. All are designed to be different than the sharp orthogonal arrangement prevalent in the prior art. The shapes of the interface structures are generally of two types: steps away from the centerline of the airfoil with a sloping surface directed toward the trailing edge and, the other design has a gap before the sloping surface. By properly shaping the step, the critical step height is increased by more than 50% over the orthogonal edged step.

Holmes, Bruce J.↗

Shapes of small satellites

The accurate measurement of limb coordinates on small satellite is the major technique for evaluating their sizes and shapes in the absence of good stereoscopic image coverage. The shapes of satellites may be clues to their internal structure if they are relaxed into ellipsoids. The distinction between irregular and ellipsoidal satellites can now be made quantitatively with the availability of many accurate limb profiles of satellites. The residuals from these fit ellipses provide a convenient and quantitative measure of the topography on the satellites. Departures from gravitational (and tidal) equipotentials would be greater, but on the average this is a good measure of the relaxed or nonrelaxed nature of the shape of the objects. The limb topography is also related to specific forms on the objects, and a systematic survey of these forms on small and larger objects is underway.

Thomas, P.↗

Shape design sensitivity analysis and optimal design of structural systems

The material derivative concept of continuum mechanics and an adjoint variable method of design sensitivity analysis are used to relate variations in structural shape to measures of structural performance. A domain method of shape design sensitivity analysis is used to best utilize the basic character of the finite element method that gives accurate information not on the boundary but in the domain. Implementation of shape design sensitivty analysis using finite element computer codes is discussed. Recent numerical results are used to demonstrate the accuracy obtainable using the method. Result of design sensitivity analysis is used to carry out design optimization of a built-up structure.

Choi, Kyung K.↗

Reduction of the radar cross section of arbitrarily shaped cavity structures

The problem of the reduction of the radar cross section (RCS) of open-ended cavities was studied. The issues investigated were reduction through lossy coating materials on the inner cavity wall and reduction through shaping of the cavity. A method was presented to calculate the RCS of any arbitrarily shaped structure in order to study the shaping problem. The limitations of this method were also addressed. The modal attenuation was studied in a multilayered coated waveguide. It was shown that by employing two layers of coating, it was possible to achieve an increase in both the magnitude of attenuation and the frequency band of effectiveness. The numerical method used in finding the roots of the characteristic equation breaks down when the coating thickness is very lossy and large in terms of wavelength. A new method of computing the RCS of an arbitrary cavity was applied to study the effects of longitudinal bending on RCS reduction. The ray and modal descriptions for the fields in a parallel plate waveguide were compared. To extend the range of validity of the Shooting and Bouncing Ray (SBR) method, the simple ray picture must be modified to account for the beam blurring.

Chou, R.↗

Shape design sensitivity analysis using domain information

A numerical method for obtaining accurate shape design sensitivity information for built-up structures is developed and demonstrated through analysis of examples. The basic character of the finite element method, which gives more accurate domain information than boundary information, is utilized for shape design sensitivity improvement. A domain approach for shape design sensitivity analysis of built-up structures is derived using the material derivative idea of structural mechanics and the adjoint variable method of design sensitivity analysis. Velocity elements and B-spline curves are introduced to alleviate difficulties in generating domain velocity fields. The regularity requirements of the design velocity field are studied.

Seong, Hwal-Gyeong↗

Fixed order compensator design based on frequency shaped cost functionals

This paper treats the design of fixed order compensators using frequency shaped cost functionals. The formulation is done in an output feedback setting which exploits an observer canonical form to represent the compensator dynamics. The major advantages of the design approach are that the order of the compensator is fixed by the design process, and it is not necessary to realize the frequency shaping dynamics as an integral part of the compensator design. This avoids the two-step approach of full state feedback design followed by the design of an observer, which in the case of a full order observer requires a compensator of order n + nf where n is the order of the plant and nf is the order of the frequency shaping realization. The formulation also precludes the use of direct feedback of the plant output, thus reducing the effect of sensor noise and improving the robustness to high frequency unmodeled dynamics. A structural vibration model describing the fast dynamics of a lightweight flexible arm is used as an example to illustrate the design procedure.

Calise, Anthony J.↗

Design modeling for shape optimization

Some important aspects of design modeling for shape optimization are discussed for both stamped sheet metal components and cast solid components. For stamped components the basis for the modeling approach is a boundary design function. Design parameters control the shape of 2-D regions. For more complex, folded plate components, the 2-D regions can be assembled using translation and rotation operations. The analysis model is automatically created using a mesh generation procedure requiring only boundary data. For less complex solid components, it was found that this approach is not suitable. For these structures, the finite element models are typically created using very sophisticated graphical modeling systems. A new approach which overlays a parameterized surface design model on an existing analysis model is described. To summarize, the future needs for solid shape design is described in terms of an extension of the previously described 2-D capability.

Botkin, M. E.↗

Structural shape optimization in multidisciplinary system synthesis

Structural shape optimization couples with other discipline optimization in the design of complex engineering systems. For instance, the wing structural weight and elastic deformations couple to aerodynamic loads and aircraft performance through drag. This coupling makes structural shape optimization a subtask in the overall vehicle synthesis. Decomposition methods for optimization and sensitivity analysis allow the specialized disciplinary methods to be used while the disciplines are temporarily decoupled, after which the interdisciplinary couplings are restored at the system level. Application of decomposition methods to structures-aerodynamics coupling in aircraft is outlined and illustrated with a numerical example of a transport aircraft. It is concluded that these methods may integrate structural and aerodynamic shape optimizations with the unified objective of the maximum aircraft performance.

Sobieszczanski-Sobieski, Jaroslaw↗

Shape sensitivity analysis of wing static aeroelastic characteristics

A method is presented to calculate analytically the sensitivity derivatives of wing static aeroelastic characteristics with respect to wing shape parameters. The wing aerodynamic response under fixed total load is predicted with Weissinger's L-method; its structural response is obtained with Giles' equivalent plate method. The characteristics of interest include the spanwise distribution of lift, trim angle of attack, rolling and pitching moments, wind induced drag, as well as the divergence dynamic pressure. The shape parameters considered are the wing area, aspect ratio, taper ratio, sweep angle, and tip twist angle. Results of sensitivity studies indicate that: (1) approximations based on analytical sensitivity derivatives can be used over wide ranges of variations of the shape parameters considered, and (2) the analytical calculation of sensitivity derivatives is significantly less expensive than the conventional finite-difference alternative.

Barthelemy, Jean-Francois M.↗

Experimental measurements in a large separation bubble due to a simulated glaze ice shape

The effect of a simulated glaze ice accretion on the aerodynamic performance of a NACA 0012 airfoil was studied experimentally. Two ice shapes were tested, one from an experimentally measured accretion and one from an accretion predicted using a computer model given the same icing conditions. Lift, drag and moment coefficients were measured for the airfoil with both ice shapes, smooth and rough. The aerodynamic performance of the two shapes compared well at positive, but not negative, angles of attack. Split hot-film probe velocity data were presented in the upper surface boundary layer and in the wake. Boundary layer parameters were presented for the separation bubble and in the reattached turbulent boundary layer.

Bragg, M. B.↗

Shape sensitivity analysis of wing static aeroelastic characteristics

A method is presented to calculate analytically the sensitivity derivatives of wing static aeroelastic characteristics with respect to wing shape parameters. The wing aerodynamic response under fixed total load is predicted using Weissinger's L-method; its structural response is obtained with Giles' equivalent plate method. The characteristics of interest in this study include the spanwise distribution of lift, trim angle of attack, rolling and pitching moments, wing induced drag as well as the divergence dynamic pressure. The shape parameters considered are the wing area, aspect ratio, taper ratio, sweep angle and tip twist angle. Results of sensitivity studies indicate that (1) approximations based on analytical sensitivity derivatives can be used for wide ranges of variations of the shape parameters considered and (2) the analytical calculation of sensitivity derivatives is significantly less expensive than the conventional finite difference alternative.

Barthelemy, Jean-Francois M.↗