Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Quantifying Properties for a Mechanistic, Predictive Understanding of Aqueous Impact on Aging of Medium and Low Voltage AC and DC Cabling in Nuclear Power Plants

To address the gap in knowledge in understanding degradation in relevant service conditions, this project aimed to develop a mechanistic, predictive model of medium and low voltage cable failure based on the primary environmental degradation parameters of aqueous immersion time, temperature, and the oxidation extent. To do so, we took a two-fold approach toward evaluating degradation as related to the aqueous condition. First, we evaluated the chemical, mechanical, and electrical properties of polymers that comprise the cabling insulation under varied aqueous conditions at different temperatures. Secondly, we evaluated the performance of insulation materials under similar accelerated aging conditions in addition to the dielectric breakdown of the cabling under submersion conditions. Thermal oxidation and immersion of LDPE thin films were done using a Parr vessel and the extent of oxidation was monitored using the carbonyl index from ATR-FTIR spectrum, a ratio quantifying the carbonyl functionality produced on the LDPE film surface. Increasing the temperature, oxidation time, and oxygen pressure increased the water-vapor permeability and the carbonyl content. Thermogravimetric analysis of the films confirmed that there is indeed an initial weight loss of the smaller molecular weight molecules and volatiles. At higher temperatures, there is a secondary mass loss. Up to 70°C, the mass loss curves were similar until 80°C, when the aged films decreased at a much greater rate with respect to increasing temperature. This was seen in the 10, 50, 90% weight loss temperatures. The mechanical properties of sheet PP and HDPE as well as injection molded LDPE, HDPE, HDPP dog bones were plotted with respect to the time spent in the Parr vessel during thermal oxidation. For the sheet PP and HDPE, the UTS and the modulus of elasticity decreased while the elongation increased. The injection-molded LDPE, HDPE, and HDPP dog bones experienced a similar trend where the changes in the properties were within experimental uncertainty. This analysis of LDPE in dry and immersive oxygen-rich environments is an important baseline for future experiments looking at other degradation mechanisms. A predictive aging model for low-density polyethylene insulative cable housings was developed. This model revealed a combination of physical and chemical processes which lead to an increase in permeability and a decrease in strength of the insulator. In creating this predictive model, a gap of knowledge in the literature was revealed in two areas: understanding how the crystallinity of a polymer changes with time and visualizing the predicted pores formed through the insulator which leads to failure. Developing and using an adapted ATR-FTIR method, crystallinity was monitored and compared to bulk crystallinity found via DSC. Inhomogeneity in crystallinity changes were observed but the FTIR method but was found to be less reliable. Pore visualization was found utilizing electrical impedance spectroscopy saturated aged polyethylene films with synthesized citrate-capped gold nanoparticles, and chloroauric acid precursor. results indicate a decreasing impedance of the polyethylene films caused by the transport of ions through the film. SEM imaging was then performed for elemental analysis of the films and counter electrodes for the presence of ions. Chloride and gold ions were detected; however, no nanoparticles were found. This gives an estimated pore size of at least 0.3 nm through the aged film. Cyclic submergence of polyethylene and polypropylene in aqueous solutions of copper sulfate and Harrison’s solution were examined. It was discovered that aging in these mixed conditions and at 90°C did cause a small, yet significant increase to tensile strength for both unaged polyethylene and polypropylene. The PE and PP in cycled and submerged conditions did not have tensile strengths significantly different from dry-aged after 16 weeks. For both solutions, it was determined that capacitance increases with both water tree depth and cable temperature and is relatively independent of changing water tree AR. As for resistance, there is no apparent change between depth percentages of 10 and 80 for both solutions. This is because the water tree has not yet entered the conductor and thus there is no shorting current flowing through the tree yet. Between 80 and 100% water tree depth, it is observed that for both solutions there is a rapid decrease in resistance because the tree is now impacting the conductor shield and allowing shorting current to flow through it. The relationship between resistance and temperature was found to be inversed. As temperature increases, resistance decreases for both water tree solutions with distilled water having the most apparent difference across the range of temperatures simulated. With regards to water tree AR, resistance was found to be relatively independent at depth percentages of 10, 50, and 70, but there was some relationship at 100% depth for both solutions. At this depth, as water tree AR increased, resistance was found to also increase. Through the examination of voltage and electric field distribution plots, it was confirmed for EPR cables that increasing water tree depth leads to increasing distortion. The increase in shorting current at 100% depth for aqueous copper sulfate compared to distilled water was also visualized. Lastly, the relationship between shorting current and temperature for narrow water trees was visualized and validated using the distribution plots. This study has led to a better understanding of the effect of cable temperature, water tree solution, and geometry of the tree region on cable degradation. Furthermore, this study has documented simulation results of water tree degradation in EPR MV cables, which had been previously lacking in information. Future work in this area will add frequency into the mix and examine what effect it has on the rate of cable degradation as a result of water treeing. To compliment the work being carried by UMD on different polymer chemistries, harvested medium voltage (MV) cables were selected for accelerated aging study at ORNL. These medium voltage cables are representative of the vintages and materials that are currently in use at existing nuclear power plants (NPPs). These cables were immersed in water at 90°C and energized for a period of two years at elevated voltage. Partial discharge was measured during this period of time to track potential degradation. Unfortunately, due to the absence of failure, the extent of integration between the UMD techniques and the harvested MV insulation was limited. However, based on the findings and from the UMD research in the previous sections on polyethylene and polypropylene, follow-on characterization for harvested MV cable insulation should focus on sample preparation to take advantage of the UMD techniques to better understand mechanistic degradation in MV cable insulations. This would include: 1.) Utilization of solutions and impedance measurement insulation to track permeability in harvested and accelerated aging insulation samples, 2.) Adaptation of gold nanoparticle synthesis for electrical impedance spectroscopy with supporting SEM characterization to study pore formation in harvested and accelerated aged insulation samples, & 3.) ATR-FTIR crystallinity with multiple temperature dependent harvested MV cable insulation under different air and submerged accelerated aging. In addition, low voltage dielectric spectroscopy and high voltage dissipation factor, tan δ, could be implemented as a condition monitoring tool for harvested MV cable insulation in submerged environments.

24 POWER TRANSMISSION AND DISTRIBUTION↗

A SIMPLIFIED ENERGY MODELING APPROACH FOR BUILDINGS

This paper introduces simplified energy modeling (SEM) approaches using DOE2 and EnergyPlus and proposes a validation method for simplified energy modeling. Simplified energy modeling can allow more design teams and owners to leverage the power of energy modeling to inform their designs and lead to greater energy savings and a lower first cost because the technologies and design strategies can be thoroughly tested against models before the decisions are made. By starting a discussion on how to develop simplified energy modeling approaches and methods to validate results, we hope to increase innovation in energy modeling software while decreasing variation between modelers. Simplified modeling is not yet widely accepted because it is unclear if the simplifications reduce the accuracy of the results. By starting an industry dialogue on a testing method for these modeling approaches, we hope to aid adoption of more streamlined tools when they can be shown to provide similar accuracy to more detailed tools. This paper proposes a method to test simplified energy modeling programs against the DOE prototype buildings. It builds on the testing procedure established for simulation engines by ASHRAE Standard 140. By comparing whole building and end use results from the accepted prototype buildings to any simplified modeling approach across multiple building types and climate zones we can determine if the simplifications create unwarranted error. We will present the SEM approach and results for a case study validation for a sample building types in 16 US climate zones from two such simplified energy modeling tools.

Energy Modeling, 90.1 Appendix G, Asset Score Tool↗

A Study on Surface Texture and Wettability of Femtosecond Laser Treated Aluminum Alloys

This research aims to study the effects of femtosecond laser treatment on surface texture and wettability properties. The first portion of this research studies 2024-T3 aluminum alloy concerning surface texture (e.g., roughness), wettability, and surface free energy. SEM images help aid the researchers in detecting minuscule changes in surface texture. Profilometry extracts topographical data from the surface. A contact angle goniometer measures contact angle, which follows the sessile drop method. Owens, Wendt, Rabel, and Kaelble's method calculates the surface free energy in conjunction with the contact angle. Femtosecond laser modification produces relatively uniform surface morphology at the macroscale. When looking at the microscale, surface morphology differs depending on the interplay between material melting and self-assembly, where the surface becomes rougher after laser treatment. Contact angle results show that all but the control sample and sample 7 exhibit hydrophobic behavior, i.e., contact angle >90°, with Sample 1 having the most significant angle of 115°. The effects of laser parameters on surface energy is apparent. More work is needed to establish correlations among these three quantities: contact angle, surface energy, and laser parameters. The second portion of this research studies aluminum alloy 6061 as the subject material with the primary goal of creating a superhydrophobic surface. A central composite design creates the laser surface texturing design of experiments. SEM images help aid the researchers in detecting minuscule changes in surface texture. A 3D optical profiler extracts topographical data from the surface. The sessile drop method incorporates a contact angle goniometer to measure the contact angle. The response surface method builds a second-order polynomial model for the contact angle and obtains optimized parameters to maximize the contact angle. This research shows that laser surface texturing can generate a wide range of surface profiles and roughness values with geometric features ranging from hundreds of μm to submicron. All three laser parameters (pulse energy, pulse duration, repetition rate) affect surface roughness and contact angle to some degree. To quantify the relationship between the contact angle, pulse energy, and pulse repetition rate, a response surface model for Al 6061 is identified and used to find the optimal conditions of E=214 μJ, tp=10 ps, and fp=2427 Hz with a predicted maximum contact angle of 161°. A confirmation experiment produces a contact angle of 168°, in good agreement with the predicted value.

Angell, Dakota↗

Differences in gasification behaviors and related properties between entrained gasifier fly ash and coal char

In the study, two fly ash samples from Texaco gasifiers were compared to coal char and the physical and chemical properties and reactivity of samples were investigated by scanning electron microscopy (SEM), SEM-energy-dispersive spectrometry (EDS), X-ray diffraction (XRD), N{sub 2} and CO{sub 2} adsorption method, and isothermal thermogravimetric analysis. The main results were obtained. The carbon content of gasified fly ashes exhibited 31-37%, which was less than the carbon content of 58-59% in the feed coal. The fly ashes exhibited higher Brunauer-Emmett-Teller (BET) surface area, richer meso- and micropores, more disordered carbon crystalline structure, and better CO{sub 2} gasification reactivity than coal char. Ashes in fly ashes occurred to agglomerate into larger spherical grains, while those in coal char do not agglomerate. The minerals in fly ashes, especial alkali and alkaline-earth metals, had a catalytic effect on gasification reactivity of fly ash carbon. In the low-temperature range, the gasification process of fly ashes is mainly in chemical control, while in the high-temperature range, it is mainly in gas diffusion control, which was similar to coal char. In addition, the carbon in fly ashes was partially gasified and activated by water vapor and exhibited higher BET surface area and better gasification activity. Consequently, the fact that these carbons in fly ashes from entrained flow gasifiers are reclaimed and reused will be considered to be feasible. 15 refs., 7 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Novel electrochemical technique: Grain control in preparation of polycrystalline BaMoO{sub 4} film

BaMoO{sub 4} films have been prepared by a novel electrochemical technique without impressed current on molybdenum substrates at room temperature in barium hydroxide aqueous solution. In order to form desired surface morphology and grain size, the BaMoO{sub 4} crystal grains have been controlled effectively by adjusting ion-concentration and adding adequate surfactant. The as-prepared BaMoO{sub 4} films have been characterized by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). SEM and XRD results indicate that the morphology, grain size, phase and crystallinity were significantly developed.

36 MATERIALS SCIENCE↗

Synthesis, characterization and catalytic activity of ordered macroporous silicas functionalized with organosulfur groups

Hybrid three-dimensionally ordered macroporous (3DOM) SiO{sub 2}-SO{sub 3}H materials with different S/Si ratio have been prepared by colloidal crystal templating method. The process involved preparation of 3DOM SiO{sub 2}-SH materials by co-condensation of (3-mercaptopropyl)triethoxysilane and tetraethoxysilane via sol-gel transformation, and following oxidation of -SH group to -SO{sub 3}H group by H{sub 2}O{sub 2}. Materials were characterized by scanning electron microscopy (SEM), Fourier transform infra-red spectrometer (FTIR), thermogravimetric analysis (TGA), and nitrogen adsorption measurement. SEM observation shows that the macropores are highly ordered with a typical 'surface-templated' structure. The surface area of 3DOM SiO{sub 2}-SH material is 25.1 m{sup 2}/g and SiO{sub 2}-SO{sub 3}H material is 18.6 m{sup 2}/g. Catalytic activity test shows that 3DOM SiO{sub 2}-SO{sub 3}H materials possess a high activity for the esterification of acetic acid and n-butanol, and the activity is increased with the amount of sulfur in the materials. This study provided significant results for developing new application of 3DOM materials.

36 MATERIALS SCIENCE↗

Shape controlled synthesis of Cu{sub 2}O and its catalytic application to synthesize amorphous carbon nanofibers

Octahedral Cu{sub 2}O particles and Cu{sub 2}O nanowires were synthesized by a simple solution-phase route using N{sub 2}H{sub 4}.H{sub 2}O as reducing agent at room temperature. Amorphous carbon nanofibers were synthesized using octahedral Cu{sub 2}O particles and an acetylene gas source at atmospheric pressure. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy and thermogravimetric (TG) analysis. SEM and TEM images indicated that most of the obtained octahedral Cu{sub 2}O particles had an edge length of 400-700 nm. The obtained nanowires had uniform diameters of about 15 nm, and the length of the nanowires ranged from 5 to 10 {mu}m. The XRD result revealed the amorphous feature of the nanofibers. IR spectrum revealed that the nanofibers consist of -CH, -CH{sub 2,} -C=C- and -CH{sub 3} groups. The concentrations of N{sub 2}H{sub 4}.H{sub 2}O and NaOH played important roles in controlling the geometric shape of the Cu{sub 2}O.

36 MATERIALS SCIENCE↗

Facile sonochemical synthesis and photoluminescent properties of lanthanide orthophosphate nanoparticles

Uniform lanthanide orthophosphate LnPO{sub 4} (Ln=La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho) nanoparticles have been systematically synthesized via a facile, fast, efficient ultrasonic irradiation of inorganic salt aqueous solution under ambient conditions without any surfactant or template. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), photoluminescence (PL) spectra as well as kinetic decays were employed to characterize the samples. The SEM and the TEM images show that the hexagonal structured lanthanide orthophosphate LnPO{sub 4} (Ln=La, Ce, Pr, Nd, Sm, Eu, Gd) products have nanorod bundles morphology, while the tetragonal LnPO{sub 4} (Ln=Tb, Dy, Ho) samples prepared under the same experimental conditions are composed of nanoparticles. HRTEM micrographs and SAED results prove that these nanostructures are polycrystalline in nature. The possible formation mechanism for LnPO{sub 4} (Ln=La-Gd) nanorod bundles is proposed. Eu{sup 3+}-doped LaPO{sub 4} and Tb{sup 3+}-doped CePO{sub 4} samples were also prepared by using the same synthetic process, which exhibit an orange-red (Eu{sup 3+}:{sup 5}D{sub 0}-{sup 7}F{sub 1,2,3,4}) and green (Tb{sup 3+}, {sup 5}D{sub 4}-{sup 7}F{sub 3,4,5,6}) emission, respectively. - Graphical Abstract: Hexagonal LnPO{sub 4} (Ln=La, Ce, Pr, Nd, Sm, Eu, Gd) and tetragonal LnPO{sub 4} (Ln=Tb, Dy, Ho) nanoparticles have been synthesized by a simple and facile sonochemical method.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preparation and luminescence properties of Ce{sup 3+} and/or Tb{sup 3+} doped LaPO{sub 4} nanofibers and microbelts by electrospinning

Ce{sup 3+} and/or Tb{sup 3+} doped LaPO{sub 4} nanofibers and microbelts have been prepared by a combination method of sol-gel process and electrospinning. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), photoluminescence (PL), low voltage cathodoluminescence (CL) and time-resolved emission spectra as well as kinetic decays were used to characterize the resulting samples. SEM and TEM results indicate the as-formed precursor fibers and belts are smooth, and the as-prepared nanofibers and microbelts consist of nanoparticles. The doped rare-earth ions show their characteristic emission under ultraviolet excitation, i.e. Ce{sup 3+} 5d-4f and Tb{sup 3+5}D{sub 4}-{sup 7}F{sub J} (J=6-3) transitions, respectively. The energy transfer process from Ce{sup 3+} to Tb{sup 3+} in LaPO{sub 4}:Ce{sup 3+}, Tb{sup 3+} nanofibers was further studied by the time-resolved emission spectra. Under low-voltage electron beam excitation, LaPO{sub 4}:Ce{sup 3+}, Tb{sup 3+} microbelt phosphors have a higher intensity than that of nanofiber phosphors. - Graphical Abstract: Ce{sup 3+} and/or Tb{sup 3+} LaPO{sub 4} nanofibers and microbelts have been prepared by electrospinning. A systematic study on the optical properties of LaPO{sub 4}:Ce{sup 3+}, Tb{sup 3+} samples has shown that they are good green-emitting phosphors in fluorescent lamps and field emission displays. The energy transfer process from Ce{sup 3+} to Tb{sup 3+} in LaPO{sub 4}:Ce{sup 3+}, Tb{sup 3+} nanofibers is further studied by the time-resolved emission spectra.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synthesis of mesoporous zeolite single crystals with cheap porogens

Mesoporous zeolite (silicalite-1, ZSM-5, TS-1) single crystals have been successfully synthesized by adding soluble starch or sodium carboxymethyl cellulose (CMC) to a conventional zeolite synthesis system. The obtained samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen sorption analysis, {sup 27}Al magic angle spinning nuclear magnetic resonance ({sup 27}Al MAS NMR), temperature-programmed desorption of ammonia (NH{sub 3}-TPD) and ultraviolet-visible spectroscopy (UV-vis). The SEM images clearly show that all zeolite crystals possess the similar morphology with particle size of about 300 nm, the TEM images reveal that irregular intracrystal pores are randomly distributed in the whole crystal. {sup 27}Al MAS NMR spectra indicate that nearly all of the Al atoms are in tetrahedral co-ordination in ZSM-5, UV-vis spectra confirm that nearly all of titanium atoms are incorporated into the framework of TS-1. The catalytic activity of meso-ZSM-5 in acetalization of cyclohexanone and meso-TS-1 in hydroxylation of phenol was also studied. The synthesis method reported in this paper is cost-effective and environmental friendly, can be easily expended to prepare other hierarchical structured zeolites. - Graphical abstract: Mesoporous zeolite single crystals were synthesized by using cheap porogens as template. Highlights: > Mesoporous zeolite (silicalite-1, ZSM-5, TS-1) single crystals were synthesized. > Soluble starch or sodium carboxymethyl cellulose (CMC) was used as porogens. > The mesoporous zeolites had connected mesopores although closed pores existed. > Higher catalytic activities were obtained.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An alternative solid-state method to prepare pyrochlore-free KTaO{sub 3} at low temperature

Perovskite-type KTaO{sub 3} powder was synthesized by an alternative solid-state method at low temperature. Stoichiometric ammonium tantalum hydroxide, K{sub 2}C{sub 2}O{sub 4} and KF were mixed in water and then dried at room temperature. The crude product was formed by calcining the dried mixture at different temperatures. Pyrochlore-free KTaO{sub 3} powder was successfully synthesized after treating the crude product with water. KF plays an important role to inhibit the formation of pyrochlore K{sub 2}Ta{sub 2}O{sub 6} during the calcination process of ammonium tantalum hydroxide/K{sub 2}C{sub 2}O{sub 4}/KF mixture. X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy, UV-vis diffuse reflectance (UV-vis) spectroscopy and thermogravimetric (TG) analysis were used to characterize the precursor compound and as-prepared samples. XRD results show that pyrochlore-free KTaO{sub 3} powder can be obtained at 600 deg. C. SEM results reveal that the as-prepared products are agglomerated and each of the agglomerations consists of many small grains with 10-30 nm in diameter. - Graphical abstract: Pyrochlore-free KTaO{sub 3} powder was prepared at 600 deg. C using tantalum hydroxide/K{sub 2}C{sub 2}O{sub 4}/KF raw materials. Pyrochlore K{sub 2}Ta{sub 2}O{sub 6} and perovskite KTaO{sub 3} coexist at 600 deg. C using tantalum hydroxide/K{sub 2}C{sub 2}O{sub 4} raw materials. Highlights: > In-situ degradation of TaO{sub x}(OH){sub 5-x}(NH{sub 4}){sub x}, K{sub 2}C{sub 2}O{sub 4} and KF promotes the reaction. > Synthesis of KTaO{sub 3} displayed a two-step reaction path with the intermediate formation of K{sub 2}TaO{sub 3}F. > Formation of intermediate K{sub 2}TaO{sub 3}F benefits to prepare pyrochlore-free KTaO{sub 3} at low temperature. > Pyrochlore-free KTaO{sub 3} is prepared at 600 deg. C, which is the lowest temperature reported so far by hard chemistry method. > Synthetic method is a facile, rapid, low price and environment friendly route.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Advanced electron microscopic techniques applied to the characterization of irradiation effects and fission product identification of irradiated TRISO coated particles from the AGR-1 experiment

Preliminary electron microscopy of coated fuel particles from the AGR-1 experiment was conducted using characterization techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), and wavelength dispersive spectroscopy (WDS). Microscopic quantification of fission-product precipitates was performed. Although numerous micro- and nano-sized precipitates observed in the coating layers during initial SEM characterization of the cross-sections, and in subsequent TEM diffraction patterns, were indexed as UPd{sub 2}Si{sub 2}, no Ag was conclusively found. Additionally, characterization of these precipitates highlighted the difficulty of measuring low concentrations of Ag in precipitates in the presence of significantly higher concentrations of Pd and U. The electron microscopy team followed a multi-directional and phased approach in the identification of fission products in irradiated TRISO fuel. The advanced electron microscopy techniques discussed in this paper, not only demonstrate the usefulness of the equipment (methods) as relevant research tools, but also provide relevant scientific results which increase the knowledge about TRISO fuel particles microstructure and fission products transport.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Three-dimensional FIB/EBSD characterization of irradiated HfAl{sub 3}-Al composite

A thermal neutron-absorbing composite comprised of 28.4 vol.% HfAl{sub 3} intermetallic particles in an Al matrix, developed for use in a conduction-cooled thermal neutron filter, will enable fast flux irradiation of materials and fuels in an existing pressurized water test reactor. In this paper, an EBSD-FIB characterization approach is used to observe the microstructural changes of the HfAl{sub 3}-Al composite in response to simulated long-term neutron irradiation. Using a focused ion beam (FIB), the sample was fabricated to 25 μm x 25 μm x 20 μm and mounted on a transmission electron microscopy (TEM) grid. A series of operations were carried out repeatedly on the sample's top surface to prepare it for scanning electron microscopy (SEM). First, a ∼ 100-nm layer was removed by high voltage FIB milling. Then, several cleaning passes were performed on the newly exposed surface using low voltage FIB milling to improve the SEM image quality. The surface was then scanned by Electron Backscattering Diffraction (EBSD) to obtain a two-dimensional image. After 50 to 100 two-dimensional images were collected, the images were stacked to reconstruct a three-dimensional model using DREAM.3D software. Two such reconstructed three dimensional models were obtained from samples of the original and post-irradiation HfAl{sub 3}-Al composite, from which the most significant microstructural change caused by neutron irradiation appears to be the size reduction of both HfAl{sub 3} and Al grains. Possible causes include thermal expansion and related thermal strain from thermal neutron capture. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

In-Pile testing of CrN, TiAIN, and AlCrN coatings on Zircaloy cladding in the Halden reactor - 2016-0011

CrN coating came out as superior and remained completely intact after the irradiation, as evidenced by SEM analysis. Based on these promising results, an in-pile experiment with coated Zircaloy claddings (containing fuel) was performed in the Halden reactor in PWR conditions in 2014. The experimental rig contained four Zircaloy-4-clad fuel rods-three coated (CrN, TiAlN, and AlCrN) and one uncoated. Due to a mechanical deformation of tubes for cooling water within the rig, the fuel rods were insufficiently cooled, resulting in a higher-than-normal cladding temperature. Nevertheless, an SEM examination showed that the CrN coating largely remained intact apart from several local spots where the coating had cracked or disappeared. Underneath the cracked coating, oxide formation was observed in the Zircaloy-4 cladding. The TiAlN and AlCrN coatings both disappeared after the irradiation. (authors)

36 MATERIALS SCIENCE↗

Understanding the influence of iron on crystallization kinetics of nepheline based glasses - 15472

Hanford site in Washington is home to 55 million US gallons of high level radioactive waste rich in sodium, alumina and iron. The strategy is to vitrify this waste in borosilicate glasses. Crystallization of nepheline/carnegeite (NaAlSiO{sub 4}) in glass melts during vitrification and canister cooling is a big challenge as it severely deteriorates the chemical durability of the glass. As the HLW borosilicate glasses are similar to basalt glass on a borate-free basis and as no borate phase crystallize on the liquidus, the crystallization chemistry of waste glasses can be described by the known phase relations of the geochemical basalt quaternary Na{sub 2}O-Al{sub 2}O{sub 3}-Fe{sub 2}O{sub 3}-SiO{sub 2} system. The objective of this study is to understand the influence of iron on the thermal stability and crystallization kinetics of model sodium- and alumina- rich simplified silicate glasses in the Na{sub 2}O-Al{sub 2}O{sub 3}-Fe{sub 2}O{sub 3}-SiO{sub 2} system designed in the primary crystallization field of nepheline. The results obtained from this study will form the baseline for understanding the nucleation and crystallization kinetics of multicomponent complex nuclear waste glasses in future. A series of glasses with compositions 25Na{sub 2}O-(25-z) Al{sub 2}O{sub 3}-zFe{sub 2}O{sub 3} -50SiO{sub 2} (mol.%) where z varies between 0 -5% has been prepared by melt-quench technique. Glasses have been labelled in reference to their Fe{sub 2}O{sub 3} content, i.e. Fe-z. We could not obtain amorphous glasses with Fe{sub 2}O{sub 3} > 5 mol.% . Glass batches comprising oxides and carbonates were melted at 1650 deg. C in Pt-Rh crucibles for 2 h. The melts were quenched in cold water to yield ∼90 g of glass. Thermal stability and crystallization kinetics of glasses was studied using differential thermal analysis (DTA). Thermal scans (30-1580 deg. C) were collected on glass particles (particle size: 0.5 mm-1 mm) at four different heating rates: 5, 10, 15 and 20 K min{sup -1} in air and inert (N{sub 2}) atmosphere. Non-isothermal crystallization kinetics of the glasses was studied using the Augis-Bennett method and Ozawa method. In accordance with the crystallization data obtained from DTA, glasses were heated in the crystallization temperature range and air quenched. Glasses were also heated from 30 deg. C to 800, 900 and 1000 deg. C for 1 h, respectively, in air and inert (N{sub 2}) atmospheres, at heating rate of 10 K min{sup -1}. Resulting glass-ceramics were characterized for their crystalline phase evolution by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Conversion of melt -to glass-ceramic during cooling DTA data was also collected for all the glasses during their conversion from melt -to -glass-ceramic during cooling at different cooling rates, in air and inert (N{sub 2}) atmosphere. In accordance with the DTA data, conversion of melt to glass-ceramic during cooling was studied by re-melting the glass frit in Pt-Rh crucibles at 1650 deg. C. The melt was allowed to cool at 10 K min{sup -1} and was air quenched at different temperatures (as per DTA data). The as obtained glass-ceramics were characterized by XRD and SEM Incorporation of Fe{sub 2}O{sub 3} in glasses decreases their crystallization temperature and increases their crystallization tendency. Parent glass (stoichiometric nepheline composition) is prone to surface crystallization. Incorporating 5 mol.% Fe{sub 2}O{sub 3} in these glasses transforms the crystallization kinetics from surface to volume nucleation. Crystallization kinetics of glass Fe-2.5 is affected by the environment (N{sub 2} vs. Air) while no significant impact of environment could be seen for glass Fe-5. Devitrification in all the glasses begins with the crystallization of carnegeite (NaAlSiO{sub 4}, orthorhombic) (∼1200 deg. C). Prolonged heat treatments leads to the crystallization of nepheline (NaAlSiO{sub 4}, hexagonal) (∼1200 deg. C) as a secondary phase. Fe{sub 2}O{sub 3} promotes the crystallization of nepheline over carnegeite via formation of magnetite as nucleation site. Iron incorporation pre-nucleates the glasses which upon heat treatment result in the formation of magnetite phase as nucleation sites, thus, shifting the mechanism of crystallization from surface to volume. Unlike carnegeite, the crystal structure of nepheline allows partial substitution of Fe{sup 3+}/Al{sup 3+}. This promotes the crystallization of nepheline over carnegeite in iron-containing glasses. Iron incorporation in nepheline-based sodium aluminosilicate glasses shifts crystallization mechanism from surface to bulk. Our results indicate that atmosphere does affect the crystallization kinetics of iron-containing aluminosilicate glasses but only when Fe{sub 2}O{sub 3} concentration is low. Since nepheline crystal structure can easily accommodate iron in comparison to carnegeite, iron seems to promote nepheline formation in these glasses at the expense of carnegeite through formation of Fe{sub 3}O{sub 4} phase as nucleation site. Future work will be focused on adding compositional complexity to these glasses and studying them further for their nucleation and crystallization behavior.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Characterization of the Uranium-Bearing Products of the Ammonia Injection Remediation Method - 15707

Commissioned in 1943, the Hanford Site is the home of the world's first full-scale nuclear production facility. After more than 40 years of processing, improper discharge and failed storage tanks have resulted in the contamination of the Hanford vadose zone with radiologically contaminated waste. Remediation methods considered for the area include sequestration of the mobile uranium by injection of ammonia (NH{sub 3}) gas. Injection of this reactive gas increases the pore water pH, promoting the dissolution of soil minerals; a subsequent re-establishment of natural conditions is believed to result in the recrystallization of those soil minerals and the co-precipitation of uranium phases. Characterization of the precipitates formed when the ammonia (NH{sub 3}) injection method, proposed for the Hanford vadose zone, is applied to synthetic pore water on a laboratory scale. This involves: Identification of the uranium-bearing phases; A study of the effect of pore water constitution on the phases produced. Synthetic pore water solutions were prepared to mimic selected constituents of the pore water from the Hanford 200 Area: Varying constituent concentrations; Observations led to modifications to increase relative uranium content: 200 ppm → 500 ppm U; Substituted sodium silicate for silicic acid. Dried samples were analyzed by SEM-EDS and powder X-ray diffraction (XRD). A suspension in ethanol was prepared and analyzed by Transmission Electron Microscope (TEM) with Selective Area Electron Diffraction (SAED). Studied and applied geochemical modeling software (Visual Minteq and Geo-chemist's Workbench) for speciation and prediction of potential species formed. Discussion/Conclusions: - SEM-EDS Analysis: Scanning electron microscopy revealed areas of high average atomic weight which would be confirmed to be uranium-rich by energy dispersive spectroscopy analysis. The samples prepared with a more than two-fold increase in uranium concentration did not show the crystal-like forms spotted in the lower [U] samples. The samples prepared with silicic acid substituted in showed little to no uranium precipitation [not shown]. - Diffraction Analysis: Powder XRD analysis of the low [U] samples confirmed the presence of repeating crystalline patterns in the precipitate samples. Nitratine (NaNO{sub 3}) showed a massive presence, potentially obscuring significant peaks in the low [U] samples. Though it was not predicted, there was a tentative match for cejkaite (Na{sub 4}(UO{sub 2})(CO{sub 3}){sub 3}). Elevated uranium samples showed none of the needle-like crystalline shapes [diffraction data pending]. TEM - SAED confirmed the presence of a polycrystalline phase. Data analysis is complex but a comparison of average d-spacings with those of reference minerals could further support a match with cejkaite. - Geochemical Modeling: The system conditions were input into geochemical modeling software to predict the forms present throughout the reaction process. The model was used to demonstrate that the pH of the system could be increased using [NH{sub 4}{sup +}] in solution to better represent the system. Using the [NH{sub 4}{sup +}] increase, the changes in significant species with increasing pH were observed. Future Work: Repeat samples will be prepared and analyzed to bolster any potential identification. Promising samples will be submitted to the PNNL's EMSL facility, which is better equipped to perform the required analyses. An expanded study on the impact of carbonate (CO{sub 3}{sup 2-}) on the phases produced.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Radiation Tolerance Studies of Commercial Strippable Coatings and Fixatives used for Decontamination - 18642

A number of commercially available products, designed for use as strippable coating and fixatives for decontamination purposes, were tested to determine their tolerability to high radiation fields and how they potentially degrade. Each product was cured and exposed to γ-radiation from a Co-60 source, up to a total dose of 500 kGy. Obvious physical colour changes and deformities were detected by visual inspection, and images captured by scanning electron microscope (SEM) showed major differences post-irradiation in some coatings. Other physical changes to the coatings were measured using Fourier-transform infrared spectroscopy (FT-IR), Raman spectroscopy, and energy-dispersive X-ray spectroscopy (EDS); both pre- and post-irradiation. FT-IR suggested that some chemical changes were taking place in the coatings, in particular the C-H bonds and the fingerprint region appeared to be drastically altered in some coatings. EDS data indicated an increase in surface oxygen content as a result of irradiation in the majority of the samples. Additionally, coating samples were subjected to analysis by gas chromatography mass spectrometry (GCMS) in order to determine the evolved gases. The GC-MS results show that short chain hydrocarbons are produced to some degree in all the coatings during irradiation. Finally, three of the best performing coatings were selected and were irradiated using an ion beam, mimicking Pu alpha particles (with energy of around 5.25 MeV). Using the Dalton Cumbrian Facility's 5 MV tandem accelerator, coating samples were irradiated by ∼5.25 MeV He{sup 2+} particles to total dose of approximately 500 kGy. Samples were analysed using SEM, FT-IR, Raman and EDS, as was done for the gamma irradiated samples, allowing a comparison to be made between α-particle and γ-ray damage. Results from the alpha and gamma irradiations showed many similarities for the comparable assessments. A number of spectral changes observed in the FT-IR analysis were consistent across both γ-ray and α-particle irradiated samples. While there were some differences, these may be attributed to the conditions under which the irradiations were carried out. The observed similarities may allow for the inference of alpha degradation by Co-60 gamma irradiation as a more easily accessible method for determining the extent of radiolytic damage. Furthermore, gamma irradiation allows for additional analysis that is currently otherwise not possible to achieve with ion-beam exposure. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Advancing Core Safety of Gen IV and Gen IV + Reactors by Encompassing High-Temperature Resistant Materials - 18673

The paper focuses on the development of materials for Gen IV/IV+ reactor core. It discusses the advancement of materials studied and their application in different components of the reactor core and other auxiliary components which will help in the development of future generation reactors. The paper summarizes the material study showing the characteristic behavior of different materials (coated with FeB and FeB{sub 2}), towards irradiation at near high temperatures and high energy neutron flux condition. The project includes different materials which are coated on the boundaries with varied thickness of FeB and FeB{sub 2}. The samples included Carbon steel, Stainless steel 310, Stainless steel 316, Inconel 718. All above-mentioned samples were received by Prof. J. Szpunar, through an industry with coatings of FeB and FeB{sub 2} with varied thickness along with a bare sample of each material. The samples were irradiated at the University of Saskatchewan reactor, with fast neutron flux of 1.1x10{sup 11} n.cm{sup -2}.sec{sup -1}. I worked on all the samples but the paper particularly focuses on, two carbon steel samples results, received so far. The methodology for the project been followed for all the samples is as follow: 1. Received samples were first polished. 2. Vickers Hardness Test. 3. Mirror polished. 4. Etched with the appropriate etchant for the material. 5. Microscopic study of the etched surface. 6. SEM imaging. 7. Sent for irradiation. 8. The same set of material testing done after irradiation, with an EBSD run on the boundary and main surface. The two Carbon Steel samples (sample 21 and 19) analyzed, were irradiated for 14 hrs. Sample 21 was a bare sample and sample 19 had a coating of FeB, FeB{sub 2} with a ∼0.0010'' thickness. The methodology was followed for material testing before and after the irradiation. The advantage of FeB and FeB{sub 2} coatings are: 1. Higher hardness - 10 times (FeB-1775 and FeB{sub 2}-1450), 2. High-stress capacity, 3. Lower abrasion, 4. Low corrosion. Through the test results obtained before and after the irradiation, I was able to get a view of coating damage at the boundaries of sample 19. The bare sample don't show any difference after irradiation but the coated sample do show cracks in the FeB layer. Which can be seen in the SEM images of sample 19. The hardness results are promising, as hardness didn't change significantly. The hardness test was done on the substrate as the coating was significantly narrow to perform the test. Though the hardness test on coatings was performed by the possessor company which show hardness higher by a factor of 10 when compared to uncoated surfaces. The XRD results, reveal irradiation effect on the crystal lattice, making it deformed, which though is usual during irradiation. The overall analysis along with EBSD done on the two samples are favorable and promising. Though it still needs to be cleared out, whether the cracks on the coating were due to irradiation or due to etching after the samples were irradiated.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗