Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Noise characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Detection and Perception of Sound by Eagles and Surrogate Raptors

One overarching objective of this program of study was the accumulation of objective, scientifically valid information relating to auditory performance of bald and golden eagles that may be used to guide the development of acoustic alerting/deterrence technologies intended to discourage encroachment into wind energy air spaces. To that end, analyses aimed at the characterization of sensitivity to sound in bald and golden eagles, along with findings in the supra-threshold, dynamic frequency spaces related to response latencies and amplitudes, leads us to conclude that bald, and golden eagles navigate the same basic working auditory space, as in other known and thus far characterized members of the diurnal raptor family. Specifically, bald and golden eagles, along with other raptor species within the group, operate in an auditory space characterized by a frequency band at least four octaves wide and centered on 2 kHz, with an upper frequency limit between 6 and 10 kHz at 80 dB SPL and a lower frequency limit that almost certainly extends below 0.2 kHz. Consequently, we recommend that signal designers use these data as a guideline in efforts to design effective and efficient acoustic alerting/deterrent systems. It is important to note that signal energy broadcast outside of this frequency band at moderate levels will not contribute to the efficacy of a deterrent but will add an unnecessary fraction to the overall acoustic pollution budget. The importance of this consideration is heightened by contemporaneous concerns related to the transmission of noise broadcast by wind energy farms. In addition, based on analyses of data acquired from red-tailed hawks using the same experimental paradigm and data acquisition system, we conclude that auditory function in the red-tailed hawk is sufficiently like that observed in bald and golden eagles to permit its use as a surrogate species. Response waveforms, threshold-frequency curves, and input-output characteristics match those of eagles closely. It should be noted however, that differences in sensitivity and slightly extended high-frequency limits of hearing should be taken into account when extrapolating findings from one species to the others. Although the inclusion of behavioral tests of red-tailed hawks to acoustic stimuli was beyond the scope of this investigation, future efforts to assess response parameters like signal-type preference and habituation rate will further elucidate their suitability to serve as eagle surrogates in behavioral studies; nonetheless, the species in question are well matched with respect to basic auditory performance. A second essential objective of this program of study was the acoustic characterization of a subset of calls comprising the vocal repertoires of bald and golden eagles that may be used to supplement auditory performance findings in the effort to guide the development of acoustic alerting signals. With regard to that objective, the vocal repertoires of both bald and golden eagle species are rich and varied. While similar in spectrographic structure, distinctive differences are also clear. Generally, golden eagles produce some calls with shorter durations, and similar “sounding” calls exhibit distinctively different spectrographic patterns than those of bald eagles. Both species produce calls that contain a wide variety of nonlinear elements that operate to enhance the rich and varied nature of commonly observed vocal products. Comparison of the average power spectra of commonly observed bald and golden eagle calls with threshold-frequency curves leads to the conclusion that call energies fall within the frequency bounds of hearing. Further, the acoustic energy of calls considered in this report tend to fall into overlapping, but different frequency ranges of the acoustic sensitivity curve. This condition may encourage signal designers to vary the frequency content of acoustic deterrence signals in the field. Finally, preliminary observations relating to the tendencies and proclivities of bald eagles to attend to the acoustic landscape lead to the conclusion that eagles monitor their immediate sound environment assiduously. Individuals respond to a variety of natural and synthetic sound signals reliably and, perhaps most relevant in the context of the engineering of acoustic alerting/deterrence technologies, habituation to most sounds considered in this effort was minimal. These preliminary results, while calling for extended behavioral testing, are promising and set the stage for the exportation of behavioral studies into real world scenarios.

17 WIND ENERGY↗
DOE OSTI2021

Radio frequency mixing modules for superconducting qubit room temperature control systems

As the number of qubits in nascent quantum processing units increases, the connectorized RF (radio frequency) analog circuits used in first generation experiments become exceedingly complex. The physical size, cost, and electrical failure rate all become limiting factors in the extensibility of control systems. We have developed a series of compact RF mixing boards to address this challenge by integrating I/Q quadrature mixing, intermediate frequency/LO (local oscillator)/RF power level adjustments, and direct current bias fine tuning on a 40 × 80 mm 2 four-layer printed circuit board with electromagnetic interference shielding. The RF mixing module is designed to work with RF and LO frequencies between 2.5 and 8.5 GHz. The typical image rejection and adjacent channel isolation are measured to be ~27 dBc and ~50 dB. By scanning the drive phase in a loopback test, the module short-term amplitude and phase linearity are typically measured to be 5 ×10 -4 (V pp /V mean ) and 1 ×10 -3 radian (pk-pk). The operation of the RF mixing board was validated by integrating it into the room temperature control system of a superconducting quantum processor and executing randomized benchmarking characterization of single and two qubit gates. We measured a single-qubit process infidelity of 9.3(3) × 10 -4 and a two-qubit process infidelity of 2.7(1) × 10 -2 .

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

A Coincident CdTe Detector Array for Enhanced Nuclear Process Monitoring

Nuclear fuel cycle aqueous separation processes desire improved real-time material characterization and process monitoring techniques; gamma coincidence spectroscopy has the potential to meet this need in these high throughput and high radiation environments based on its ability to reduce background noise, thereby enhancing detection limits and improving isotopic identification accuracy. A detector array composed of three CdTe detectors was designed to surround a chemical processing pipe in a reprocessing facility and evaluate the feasibility of passively assaying the nuclear materials flowing though this measurement point. This array uses commercial off the shelf components that are radiation hard and highly efficiency at low energies relevant to actinide photon signatures. Detector efficiency characterizations, coincidence detection, and potential configuration improvements are presented here.

Good, Erin C.↗
DOE OSTI2021

Post-landing major element quantification using SuperCam laser induced breakdown spectroscopy

The SuperCam instrument on the Perseverance Mars 2020 rover uses a pulsed 1064 nm laser to ablate targets at a distance and conduct laser induced breakdown spectroscopy (LIBS) by analyzing the light from the resulting plasma. SuperCam LIBS spectra are preprocessed to remove ambient light, noise, and the continuum signal present in LIBS observations. Prior to quantification, spectra are masked to remove noisier spectrometer regions and spectra are normalized to minimize signal fluctuations and effects of target distance. In some cases, the spectra are also standardized or binned prior to quantification. To determine quantitative elemental compositions of diverse geologic materials at Jezero crater, Mars, we use a suite of 1198 laboratory spectra of 334 well-characterized reference samples. The samples were selected to span a wide range of compositions and include typical silicate rocks, pure minerals (e.g., silicates, sulfates, carbonates, oxides), more unusual compositions (e.g., Mn ore and sodalite), and replicates of the sintered SuperCam calibration targets (SCCTs) onboard the rover. For each major element (SiO 2 , TiO 2 , Al 2 O 3 , FeO T , MgO, CaO, Na 2 O, K 2 O), the database was subdivided into five “folds” with similar distributions of the element of interest. One fold was held out as an independent test set, and the remaining four folds were used to optimize multivariate regression models relating the spectrum to the composition. We considered a variety of models, and selected several for further investigation for each element, based primarily on the root mean squared error of prediction (RMSEP) on the test set, when analyzed at 3 m. In cases with several models of comparable performance at 3 m, we incorporated the SCCT performance at different distances to choose the preferred model. Shortly after landing on Mars and collecting initial spectra of geologic targets, we selected one model per element. Subsequently, with additional data from geologic targets, some models were revised to ensure results that are more consistent with geochemical constraints. The calibration discussed here is a snapshot of an ongoing effort to deliver the most accurate chemical compositions with SuperCam LIBS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Consensus Equilibrium for Subsurface Delineation

Heterogeneity and insufficient site characterization limit our knowledge of the subsurface. Inversion techniques, which minimize the mismatch between observations and model predictions, have become an essential tool of subsurface characterization. Most optimization-based approaches fail to incorporate various implicit priors and capture the geological complexity. We overcome these limitations by deploying the plug-and-play and consensus equilibrium (CE) strategies, which provide a flexible framework for image reconstruction. Our CE methodology for spatial delineation of geologic formations consists of an image denoiser and a variational auto-encoder (deep learning-based emulator). The former ameliorates the reconstruction noise, yielding well-defined geological structures; its mathematical equivalence with the proximal operator allows the deployment of advanced denoisers (e.g., CNN-based denoiser) that do not correspond to a regularization objective. The latter defines a geology prior that imposes a geological constraint, for example, continuity and shape of geological features, onto the reconstructed image. Here, we conduct a series of numerical experiments dealing with transient two-dimensional flow driven by a pumping well and natural hydraulic head gradient. They demonstrate the CE framework's ability to delineate, both probabilistically and deterministically, complex subsurface environments with sufficient quality.

42 ENGINEERING↗
DOE OSTI2021

Origin of mechanical and dielectric losses from two-level systems in amorphous silicon

Amorphous silicon contains tunneling two-level systems, which are the dominant energy loss mechanisms for amorphous solids at low temperatures. These two-level systems affect both mechanical and electromagnetic oscillators and are believed to produce thermal and electromagnetic noise and energy loss. However, it is unclear whether the two-level systems that dominate mechanical and dielectric losses are the same; the former relies on the coupling between phonons and two-level systems, with an elastic field coupling constant γ while the latter depends on a two-level systems dipole moment p0, which couples to the electromagnetic field. Mechanical and dielectric loss measurements as well as structural characterization were performed on amorphous silicon thin films grown by electron beam deposition with a range of growth parameters. Samples grown at 425 °C show a large reduction of mechanical loss (34 times) and a far smaller reduction of dielectric loss (2.3 times) compared to those grown at room temperature. Additionally, mechanical loss shows lower loss for thicker films, while dielectric loss shows lower loss for thinner films. Overall, analysis of these results indicate that mechanical loss correlates with atomic density, while dielectric loss correlates with dangling-bond density, suggesting a different origin for these two energy dissipation processes in amorphous silicon.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Towards Three-Dimensional Neutron Imaging with Light-field Technology

A broad range of applications in nuclear safeguards and security can benefit from compact, fast neutron imagers with large angular acceptance. However, accurate 3D multi-vertex reconstruction in a monolithic detector remains a significant barrier to realization. Current approaches, such as the centroiding approach and the use of shadow masks, have not yet resulted in a successful demonstration in a light-starved environment. This project explored the use of cutting-edge technology—a light field camera—which inherently preserves both the spatial and directional information of incident light. Such technology can, in principle, resolve multi-vertex events and offer accurate position reconstruction in 3D with relatively simple readout electronics. Since the project's inception in May 2023, we have built an experimental setup to calibrate and characterize a commercial light-field camera (Lytro Illum). We assessed its 3D event reconstruction capability in a relatively low-light intensity environment by analyzing the cross-correlation of a series of 2D images of a characterized tunable light source taken at various distances. A sub-cm resolution, lower than typical neutron interaction separations in a compact scintillator volume, was observed with the LED light source, suggesting the promising capability of its nominal optics design to provide the adequate resolution required for a compact monolithic neutron directional detector. However, using a light-field-based readout for a neutron camera requires incorporating an ultra-low-noise light sensor, which is beyond the scope of this project. We also initiated the development of a 3D light-field-based reconstruction algorithm tailored to sparse scenes, as expected from particle interactions in a scintillator medium. Additionally, we demonstrated the capability of the algorithm to replicate the ground truth. Finally, we began the development of a neutron directional detector simulation to determine the performance criteria for light-field-based reconstruction that allows for good neutron directional reconstruction. This Feasibility Study has led to a successful follow-up project under the DNN R&D innovation portfolio starting May 2024.

42 ENGINEERING↗
NASA NTRS1991

Coherent Doppler lidar for automated space vehicle rendezvous, stationkeeping and capture

The inherent spatial resolution of laser radar makes ladar or lidar an attractive candidate for Automated Rendezvous and Capture application. Previous applications were based on incoherent lidar techniques, requiring retro-reflectors on the target vehicle. Technology improvements (reduced size, no cryogenic cooling requirement) have greatly enhanced the construction of coherent lidar systems. Coherent lidar permits the acquisition of non-cooperative targets at ranges that are limited by the detection capability rather than by the signal-to-noise ratio (SNR) requirements. The sensor can provide translational state information (range, velocity, and angle) by direct measurement and, when used with any array detector, also can provide attitude information by Doppler imaging techniques. Identification of the target is accomplished by scanning with a high pulse repetition frequency (dependent on the SNR). The system performance is independent of range and should not be constrained by sun angle. An initial effort to characterize a multi-element detection system has resulted in a system that is expected to work to a minimum range of 1 meter. The system size, weight and power requirements are dependent on the operating range; 10 km range requires a diameter of 3 centimeters with overall size at 3 x 3 x 15 to 30 cm, while 100 km range requires a 30 cm diameter.

Bilbro, James A.↗
NASA NTRS1999

Application Focused Schlieren to Nozzle Ejector Flowfields

The motivation of the testing was to reduce noise generated by eddy Mach wave emission via enhanced mixing in the jet plume. This was to be accomplished through the use of an ejector shroud, which would bring in cooler ambient fluid to mix with the hotter jet flow. In addition, the contour of the mixer, with its chutes and lobes, would accentuate the merging of the outer and inner flows. The objective of the focused schlieren work was to characterize the mixing performance inside of the ejector. Using flow visualization allowed this to be accomplished in a non-intrusive manner.

Mitchell, L. Kerry↗
NASA NTRS2018

Smartphone scene generator for efficient characterization of visible imaging detectors

Full characterization of imaging detectors involves subjecting them to spatially and temporally varying illumination patterns over a large dynamic range. Here we present a scene generator that fulfills many of these functions. Based on a modern smartphone, it has a number of good features, including high spatial resolution (13 um), high dynamic range (∼104), near-Poisson limited illumination stability over time periods from 100 ms to many days, and no background noise. The system does not require any moving parts and may be constructed at modest cost. We present the optical, mechanical, and software design, test data validating the performance, and application examples.

Demers, Richard T.↗
DOE OSTI2021

Case Study of High-Throughput Drug Screening and Remote Data Collection for SARS-CoV-2 Main Protease by Using Serial Femtosecond X-ray Crystallography

Since early 2020, COVID-19 has grown to affect the lives of billions globally. A worldwide investigation has been ongoing for characterizing the virus and also for finding an effective drug and developing vaccines. As time has been of the essence, a crucial part of this research has been drug repurposing; therefore, confirmation of in silico drug screening studies have been carried out for this purpose. Here we demonstrated the possibility of screening a variety of drugs efficiently by leveraging a high data collection rate of 120 images/second with the new low-noise, high dynamic range ePix10k2M Pixel Array Detector installed at the Macromolecular Femtosecond Crystallography (MFX) instrument at the Linac Coherent Light Source (LCLS). The X-ray Free-Electron Laser (XFEL) is used for remote high-throughput data collection for drug repurposing of the main protease (Mpro) of SARS-CoV-2 at ambient temperature with mitigated X-ray radiation damage. We obtained multiple structures soaked with nine drug candidate molecules in two crystal forms. Although our drug binding attempts failed, we successfully established a high-throughput Serial Femtosecond X-ray crystallographic (SFX) data collection protocol.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1976

Simulated performance of coded PCM/FM modem on Rician fading channel

This paper describes a simulation approach to characterizing the performance of a coded PCM/FM modem operating on the classical Rician fading channel. In particular, we consider the performance of short constraint length convolutional codes in conjunction with Viterbi maximum likelihood decoding. The receiver consists of a narrowband filter followed by an ideal limiter/discriminator. Primary interest is in the bit error probability performance parameterized by both the fading channel and receiver parameters. Particular attention is given to simulating the impulse noise appearing at the discriminator output. This is the 'click' noise caused by encirclements of the origin by the instantaneous signal-plus-noise phasor. Results include the effects of channel memory and narrowband receiver filtering effects on overall bit error probability.

Modestino, J. W.↗
NASA NTRS1988

Preliminary analysis of Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) for mineralogic mapping at sites in Nevada and Colorado

Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data for sites in Nevada and Colorado were evaluated to determine their utility for mineralogical mapping in support of geologic investigations. Equal energy normalization is commonly used with imaging spectrometer data to reduce albedo effects. Spectra, profiles, and stacked, color-coded spectra were extracted from the AVIRIS data using an interactive analysis program (QLook) and these derivative data were compared to Airborne Imaging Spectrometer (AIS) results, field and laboratory spectra, and geologic maps. A feature extraction algorithm was used to extract and characterize absorption features from AVIRIS and laboratory spectra, allowing direct comparison of the position and shape of absorption features. Both muscovite and carbonate spectra were identified in the Nevada AVIRIS data by comparison with laboratory and AIS spectra, and an image was made that showed the distribution of these minerals for the entire site. Additional, distinctive spectra were located for an unknown mineral. For the two Colorado sites, the signal-to-noise problem was significantly worse and attempts to extract meaningful spectra were unsuccessful. Problems with the Colorado AVIRIS data were accentuated by the IAR reflectance technique because of moderate vegetation cover. Improved signal-to-noise and alternative calibration procedures will be required to produce satisfactory reflectance spectra from these data. Although the AVIRIS data were useful for mapping strong mineral absorption features and producing mineral maps at the Nevada site, it is clear that significant improvements to the instrument performance are required before AVIRIS will be an operational instrument.

Kruse, Fred A.↗
NASA NTRS1994

Multi-Flight-Phase GPS Navigation Filter Applications to Terrestrial Vehicle Navigation and Positioning

A candidate onboard space navigation filter demonstrated excellent performance (less than 8 meter level RMS semi-major axis accuracy) in performing orbit determination of a low-Earth orbit Explorer satellite using single-frequency real GPS data. This performance is significantly better than predicted by other simulation studies using dual-frequency GPS data. The study results revealed the significance of two new modeling approaches evaluated in the work. One approach introduces a single-frequency ionospheric correction through pseudo-range and phase range averaging implementation. The other approach demonstrates a precise axis-dependent characterization of dynamic sample space uncertainty to compute a more accurate Kalman filter gain. Additionally, this navigation filter demonstrates a flexibility to accommodate both perturbational dynamic and observational biases required for multi-flight phase and inhomogeneous application environments. This paper reviews the potential application of these methods and the filter structure to terrestrial vehicle and positioning applications. Both the single-frequency ionospheric correction method and the axis-dependent state noise modeling approach offer valuable contributions in cost and accuracy improvements for terrestrial GPS receivers. With a modular design approach to either 'plug-in' or 'unplug' various force models, this multi-flight phase navigation filter design structure also provides a versatile GPS navigation software engine for both atmospheric and exo-atmospheric navigation or positioning use, thereby streamlining the flight phase or application-dependent software requirements. Thus, a standardized GPS navigation software engine that can reduce the development and maintenance cost of commercial GPS receivers is now possible.

Park, Young W.↗
NASA NTRS1999

Fractal Characterization of Hyperspectral Imagery

Two Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) hyperspectral images selected from the Los Angeles area, one representing urban and the other, rural, were used to examine their spatial complexity across their entire spectrum of the remote sensing data. Using the ICAMS (Image Characterization And Modeling System) software, we computed the fractal dimension values via the isarithm and triangular prism methods for all 224 bands in the two AVIRIS scenes. The resultant fractal dimensions reflect changes in image complexity across the spectral range of the hyperspectral images. Both the isarithm and triangular prism methods detect unusually high D values on the spectral bands that fall within the atmospheric absorption and scattering zones where signature to noise ratios are low. Fractal dimensions for the urban area resulted in higher values than for the rural landscape, and the differences between the resulting D values are more distinct in the visible bands. The triangular prism method is sensitive to a few random speckles in the images, leading to a lower dimensionality. On the contrary, the isarithm method will ignore the speckles and focus on the major variation dominating the surface, thus resulting in a higher dimension. It is seen where the fractal curves plotted for the entire bandwidth range of the hyperspectral images could be used to distinguish landscape types as well as for screening noisy bands.

Qiu, Hon-Iie↗
NASA NTRS2004

Digital communication constraints in prior space missions

Digital communication is crucial for space endeavors. Jt transmits scientific and command data between earth stations and the spacecraft crew. It facilitates communications between astronauts, and provides live coverage during all phases of the mission. Digital communications provide ground stations and spacecraft crew precise data on the spacecraft position throughout the entire mission. Lessons learned from prior space missions are valuable for our new lunar and Mars missions set by our president s speech. These data will save our agency time and money, and set course our current developing technologies. Limitations on digital communications equipment pertaining mass, volume, data rate, frequency, antenna type and size, modulation, format, and power in the passed space missions are of particular interest. This activity is in support of ongoing communication architectural studies pertaining to robotic and human lunar exploration. The design capabilities and functionalities will depend on the space and power allocated for digital communication equipment. My contribution will be gathering these data, write a report, and present it to Communications Technology Division Staff. Antenna design is very carefully studied for each mission scenario. Currently, Phased array antennas are being developed for the lunar mission. Phased array antennas use little power, and electronically steer a beam instead of DC motors. There are 615 patches in the phased array antenna. These patches have to be modified to have high yield. 50 patches were created for testing. My part is to assist in the characterization of these patch antennas, and determine whether or not certain modifications to quartz micro-strip patch radiators result in a significant yield to warrant proceeding with repairs to the prototype 19 GHz ferroelectric reflect-array antenna. This work requires learning how to calibrate an automatic network, and mounting and testing antennas in coaxial fixtures. The purpose of this activity is to assist in the set-up of phase noise instrumentation, assist in the process of automated wire bonding, assist in the design and optimization of tunable microwave components, especially phase shifters, based on thin ferroelectric films, and learn how to use commercial electromagnetic simulation software.

Yassine, Nathan K.↗
NASA NTRS2007

Design and Fabrication Highlights Enabling a 2 mm, 128 Element Bolometer Array for GISMO

The Backshort-Under-Grid (BUG) superconducting bolometer array architecture is intended to be highly versatile, operating in a large range of wavelengths and background conditions. We have undertaken a three-year program to develop key technologies and processes required to build kilopixel arrays. To validate the basic array design and to demonstrate its applicability for future kilopixel arrays, we have chosen to demonstrate a 128 element bolometer array optimized for 2 mm wavelength using a newly built Goddard instrument, GISMO (Goddard /RAM Superconducting 2-millimeter Observer). The arrays are fabricated using batch wafer processing developed and optimized for high pixel yield, low noise, and high uniformity. The molybdenum-gold superconducting transition edge sensors are fabricated using batch sputter deposition and are patterned using dry etch techniques developed at Goddard. With a detector pitch of 2 mm 8x16 array for GISMO occupies nearly one half of the processing area of a 100 mm silicon-on-insulator starting wafer. Two such arrays are produced from a single wafer along with witness samples for process characterization. To provide thermal isolation for the detector elements, at the end of the process over 90% of the silicon must be removed using deep reactive ion etching techniques. The electrical connections for each bolometer element are patterned on the top edge of the square grid supporting the array. The design considerations unique to GISMO, key fabrication challenges, and laboratory experimental results will be presented.

Allen, Christine↗
DOE OSTI2025

Syncopated dynamical decoupling to suppress crosstalk in quantum circuits

Theoretically understanding and experimentally characterizing and modifying the underlying Hamiltonian of a quantum system is of utmost importance in achieving high-fidelity quantum gates for quantum computing. Here, in this work, we explore the use of dynamical decoupling (DD) in characterizing and suppressing undesired two-qubit couplings as well as the underlying single-qubit decoherence, both significant hurdles to achieving precise quantum control and realizing quantum computing on many hardware prototypes. Through discrete search of DD sequences, we identify sequences that protect against decoherence and selectively target unwanted two-qubit interactions of general form. On a transmon-qubit-based superconducting quantum device, we identify separate white and 1/𝑓 noise components underlying the single-qubit decoherence and a static ZZ coupling between pairs of qubits. A family of syncopated DD sequences is found and their efficiency is demonstrated in two-qubit benchmarking experiments. The syncopated decoupling technique significantly boosts performance in a realistic algorithmic quantum circuit.

97 MATHEMATICS AND COMPUTING↗