SEARCH · Engineering Papers

Results for “MOLD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

All sources NASA NTRS DOE OSTI

NASA NTRS2023

Structural Design and Aeromechanical Analysis of Unconventional Blades for Future Mars Rotorcraft

The structural design for rotor blades with thin, unconventional airfoils for Earth-based testing is obtained using three-Dimensional (3D) aeromechanical analysis in support of the NASA ROAMX project. The outer mold line was provided by NASA, but the internal structural design was developed at the University of Maryland and is presented here along with a thorough aeromechanical analysis. The main objectives are to verify the structural integrity of the design and understand the unique aeroelastic behavior of the non-conventional airfoils designed for low-Reynolds number and high subsonic Mach number. Four different blade models are considered, with the pitch axis varied from quarter-chord to mid-chord to determine the effect of C.G. offset on natural frequencies, blade deformations, root loads, and 3D stresses. First, torsional stability is calculated for each of the designs – especially important due to the low Lock number on Mars. All four blade designs are studied under rotation in vacuum, and significant reductions in root loads and 3D stresses are achieved by moving the pitch axis closer to mid-chord to reduce the C.G. offset. Based on the vacuum analysis, the blade design with the pitch axis at 40% chord is selected for aeromechanical analysis. The blade control load, airloads, deformations, and 3D stresses are studied for steady hover. Dynamic control load and dynamic 3D stresses are studied for unsteady hover achieved using cyclic. Significant elastic twist is observed due to the trapeze effect and propeller moment, affecting the spanwise distribution of aerodynamic loads on the blades. The dynamic control load is found to increase significantly due to inertial coupling from the C.G. offset. The dynamic stresses also increase, although still have factors of safety greater than two for both tensile and compressive stress.

Structural Design↗

NASA NTRS2023

Subsonic Ultra Green Aircraft Research: Phase IV Final Report – Volume I Mach 0.80 Transonic Truss-Braced Wing High-Speed Design Report

This design report summarizes work performed by the Boeing Subsonic Ultra-Green Aircraft Research (SUGAR) team from December 2016 through June 2018. In Phase IV of the SUGAR program, Boeing is working to improve the productivity of a TTBW configuration by updating the Mach 0.745 vehicle concept to operate efficiently at Mach 0.80. Due to the aerodynamic and structural design challenges associated with adapting the design to a higher speed, design tasks have been broken into several subtasks. The information in this report (Volume I) documents the development of a Mach 0.80 vehicle outer mold line, maturation of TTBW structural concepts, and presents a preliminary high-liftsystem assessment. Results from these studies were integrated into an aircraft-level performance code that estimates the benefits of TTBW technology, both on its own and as a part of the SUGAR integrated technology suite. The aerodynamic performance results presented herein detail the high cruise efficiency of the TTBW concept operating at M=0.80. Results from the RANS code OVERFLOW indicate that the TTBW is aerodynamically well suited for operation at the design M=0.80 transonic cruise Mach number. Aircraft-level performance predictions show that the TTBW offers a 7.2% improvement in fuel burn (per seat) for an economic mission of 900nm, and a 9.0% improvement in fuel burn (per seat) for a 3500nm mission with full passenger payload, relative to an aspect ratio 13 conventional tube and wing configuration of equivalent technology. Integration of the TTBW performance benefits into the SUGAR technology suite shows a 55.9% reduction in fuel burn (for the economic mission) relative to the reference (SUGAR Free) aircraft, which is a consistently sized traditional cantilever wing, single-aisle transport typical of the 2008 fleet. This benefit does not include the performance improvement potential of hybrid-electric systems studied in earlier phases of the SUGAR program Structural concept development work completed in Phase IV has identified several strut attachment concepts that are worth additional development activity – an inboard strut attachment swivel joint concept (which enables the strut to carry axial loads while avoiding strut bending induced by wing twist during flight) significantly simplifies the construction of the main strut. An outboard offset strut attachment concept holds significant potential for further reductions in wing-strut interference drag. Based on work performed to date on Phase IV and the previous phases of the SUGAR program, the TTBW concept continues to remain a viable concept for significantly improving the performance of future aircraft. High-fidelity aerodynamic analysis of the Mach 0.80 TTBW aircraft has shown fuel burn improvement that has exceeded initial expectations despite the increase in cruise Mach number. Structural concept maturation has continued to refine the TTBW structure, and has found no obvious ‘show-stoppers’ to date. Therefore, the potential benefit of improved performance through the use of a very high aspect ratio strut-braced wing continues to warrant additional study

SUGAR↗

NASA NTRSDate not supplied

Heatshield for Extreme Entry Environment Technology (Heeet) and 3D Woven TPS Readiness for Outer Planet Probe Missions

Recent mission studies have shown entry at Uranus or at Neptune will require 3-D Woven TPS, either the two-layer HEEET or the single layer 3MDCP, with 3MDCP being more mass efficient. The 3MDCP capability being developed to support MSR EES is sufficient for the Ice Giants if the probe size is 1.25 m or less. [The Uranus Orbiter Probe (UOP) Flagship study for the Decadal used a 1.26m diameter probe.] For larger diameters, dual layer HEEET is easily scalable and is already at TRL 6. It is possible to develop a seam approach that would allow the use of 3MDCP; the resultant mass savings could warrant such a development. Ames is already working on a concept towards this. If aerocapture becomes part of the mission design for Uranus, delivery of the probe from orbit will be easier. Whether or not the probe is delivered from orbit, 3-D Woven (HEEET or 3MDCP) is the only TPS qualified to enable Ice Giant in situ probes. In addition to UOP, Saturn probe mission concepts will be enabled by 3-D Woven, either HEEET or 3MDCP. Launch periods for the UOP flagship or a Saturn probe mission in the early to mid 2030s requires the community to ensure that the 3D woven capability does not atrophy. Currently other than MSR EES, no other mission requires 3-D wovens, and the manufacturing for MSR will be completed by 2023. A gap in production of 5 or more years requires careful monitoring of the industrial base. In addition, manufacturing of 3-D woven TPS, from procurement and weaving to molding and infusion, is a minimum 2-year activity. In response to the threat of atrophy and the time critical and intensive nature of restarting weaving, advocacy from OPAG to NASA SMD for a sustainability effort would ensure in situ exploration of the outer planets in the decades to come.

M Gasch↗

NASA NTRSDate not supplied

Parametric Study of the Forward Attachment Geometry for the Space Launch System Next Generation Booster

Launch vehicle transonic buffet environments can generate large dynamic structural loads and vibratory responses. For the Space Launch System (SLS) vehicle, the highest transonic buffet environments have been observed in the multibody region between the core and solid rocket boosters, particularly downstream of the booster forward attachment. The buffet environment is particularly sensitive to the outer mold line (OML) of the forward attachment, and even relatively minor geometry changes can have large impacts on buffet and other aerodynamic environments. The SLS program is redesigning the booster for the Block 2 vehicle to support updated mission goals. This redesign necessitated changes in the forward attachment geometry, which raised concerns about the buffet and vibroacoustic environments. A preliminary study was conducted that developed multiple forward attachment geometries that satisfied the programmatic requirements, but the aerodynamic environment impacts were unclear. In March 2022, a wind-tunnel test was conducted at the NASA Ames 11- by 11-foot Transonic Wind Tunnel to study these environments generated from each of the configurations in order to select the most viable candidate. This paper will discuss this test campaign, the results from the parametric study, as well as general observations regarding OML features that impact the buffet environment. Buffet environments will be presented and compared for each configuration and comparisons presented where applicable.

buffet↗

NASA NTRSDate not supplied

Parametric Study of the Forward Attachment Geometry for the Space Launch System Next Generation Booster

buffet↗

NASA NTRS2022

Solid-State Ultracapacitor Polymer Composite

An ultracapacitor made from a polymer loaded with ceramic powder would have several advantages over current ultracapacitors and batteries. First is the possibility of it being printable, which would allow for printing the energy storage device along with the circuit instead of having to find a way to add one later without damaging the rest of the components. When not printed in a specific design for use on a printed wiring board, this type of ultracapacitor could still be cured via a mold to a shape suitable to specific applications. Many polymers maintain some flexibility even after curing, such as the silicone used in this study. The manufacturing process would also be far simpler than that of conventional ultracapacitors.In this work, solid-state ultracapacitors were made by adding the dielectric powder to a two-part polymer (resin and hardener) at the same time. The mixture was then cured in the desired shape at a low temperature until completely set. The addition of the powder to the polymer increased its dielectric properties while leaving most of its physical properties unaltered. At higher powder loading percentages, there were some physical changes as the maximum loading point was approached. To determine the efficiency of these solid-state ultracapacitors, their capacitances were tested, and their dielectric constants (DCs) were measured and compared.

energy storage↗

NASA NTRSDate not supplied

Validation of Cryogenic Propellant Tank Self-Pressurization

NASA’s near-future long-term space missions necessitate advancements in cryogenic fluid management (CFM), which includes safe and reliable long-term propellant storage. Consequently, NASA STMD (Space Technology Mission Directorate) has established the CFM Portfolio Project to improve CFM technologies for upcoming missions. As a part of CFM Modeling Portfolio, NASA Marshall Space Flight Center’s (MSFC) Fluid Dynamics branch within the Propulsion Systems Department is tasked with assessing and improving computational tools used to support flight projects such as Human Lander System and Commercial Lunar Payload Services. One of the challenging modeling problems is that of self-pressurization of propellant tank due to heat leakage over long time periods. Reduced order and nodal tools find it extremely difficult to accurately predict self-pressurization under transient conditions or where complex flow patterns or thermal gradients exist, and application of 3-D CFD (computational fluid dynamics) simulations is necessary to characterize these problems. Until recently, CFD simulations for these long-term processes (order of hours or days) have been too impractical to conduct due to prohibitive wall time and computational resource requirements. The requisite CFD tool need to be efficient, computationally scalable, modular with ability to incorporate various physics models, and robust enough to not accumulate conservation errors over several hours of simulated time. NASA MSFC’s Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. In this paper, we validate Loci-Stream for predicting self-pressurization of a flight scale propellant tank so it can serve as a reliable design and analysis tool for NASA’s CFM application needs. Liquid hydrogen tank pressurization tests carried out at the K-site testing facility provide a reliable data set for this purpose. These tests were simulated using Loci-Stream solver with VOF module as well as a hybrid approach which uses a lumped model for the ullage gas domain and CFD simulation of the liquid propellant. Both are shown to have very good predictive capabilities over multiple K-site experiments.

Hong Q. Yang↗

NASA NTRSDate not supplied

Validation of Cryogenic Propellant Tank Self-Pressurization

NASA's near-future long-term space missions necessitate advancements in cryogenic fluid management (CFM), which includes safe and reliable long-term propellant storage. Consequently, NASA STMD (Space Technology Mission Directorate) has established the CFM Portfolio Project to improve CFM technologies for upcoming missions. As a part of CFM Modeling Portfolio, NASA Marshall Space Flight Center's (MSFC) Fluid Dynamics branch within the Propulsion Systems Department is tasked with assessing and improving computational tools used to support flight projects such as Human Lander System and Commercial Lunar Payload Services. One of the challenging modeling problems is that of self-pressurization of propellant tank due to heat leakage over long time periods. Reduced order and nodal tools find it extremely difficult to accurately predict self-pressurization under transient conditions or where complex flow patterns or thermal gradients exist, and application of 3-D CFD (computational fluid dynamics) simulations is necessary to characterize these problems. Until recently, CFD simulations for these long-term processes (order of hours or days) have been too impractical to conduct due to prohibitive wall time and computational resource requirements. The requisite CFD tool need to be efficient, computationally scalable, modular with ability to incorporate various physics models, and robust enough to not accumulate conservation errors over several hours of simulated time. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. In this paper, we validate Loci-Stream for predicting self-pressurization of a flight scale propellant tank so it can serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the K-site testing facility provide a reliable data set for this purpose. These tests were simulated using Loci-Stream solver with VOF module as well as a hybrid approach which uses a lumped model for the ullage gas domain and CFD simulation of the liquid propellant. Both are shown to have very good predictive capabilities over multiple K-site experiments.

cryogenic fluid management↗

NASA NTRSDate not supplied

Automated Reconfigurable Mission Adaptive Digital Assembly Systems (ARMADAS): Robotically Assembled Sustainable Lunar Infrastructure

Introduction: The Automated Reconfigurable Mission Adaptive Digital Assembly Systems (ARMADAS) project at NASA Ames Research Center is developing autonomous infrastructure, instrumentation, and spacecraft assembly and manufacturing capabilities for next generation exploration and science missions, with a goal to change the cost scaling of these missions relative to mission size and duration. Using a building-block approach with a 'kit of parts' composed of ultra-light, high-performance mechanical metamaterials, simplified robots leverage the period environment to achieve high levels of autonomy and reliability for in-space and surface assembly of large-scale apertures, solar-arrays, towers, habitats, and other infrastructure. Robots and structure break down into a compact form factor for launch. By leveraging economies of scale and achieving high-packing ratios, ARMADAS technology can revolutionize possible space missions by breaking the tyranny of the launch shroud, decreasing development times, decreasing mission costs for transformative science capability, and providing a scalable and versatile space infrastructure strategy. Capabilities: To date, the ARMADAS project has demonstrated autonomous assembly of large numbers of structural modules into a meters-scale structure in an earth gravity environment. The mechanical performance is on par with conventional space structures, at a fraction of the cost. By using highly repeatable manufacturing processes (injection molding carbon fiber reinforced space-rated polymers), the structures are both cost effective and highly precise. The ARAMADAS system carefully designs parts for high-precision assembly–the simple and cost-effective robots build structures much larger and more precise than themselves. While maintaining structural efficiency, the ARMADAS system encompasses many functional module types, including for solar power, comm/power routing, etc., that will enable entire infrastructure systems to be engineered and autonomously assembled with modular parts. With well-defined interfaces, custom instrumentation modules can easily be added to fit many mission objectives. Lunar Infrastructure Vision: At the LSIC spring meeting, ARMADAS will present a vision for a general-purpose lunar construction kit capable of meeting a wide variety of lunar surface infrastructure needs (Figure 1). Investing in an ecosystem of reconfigurable, discretely repairable parts and robots enables systems than can expand their capability, reconfigure to meet emergency or unforeseen needs, self-repair and reduce spare-part needs. With a small set of parts (module types), a wide variety of infrastructure needs can be met. Footing modules will allow infrastructure construction at locations with no surface preparation. Footer, primary structure, and rail modules can create reconfigurable rail systems. These rail systems can be used to reduce cost-of-transport between frequently accessed sites, provide dust mitigation, and convey power and communications. High-performance structure modules combined with power-routing and solar modules can create tall towers for power and communication. Concepts for habitats and garages encompass a structure to support regolith cover for a pre-integrated module to an entirely ARMADAS system-based structure. This system can be leveraged by many in-situ resource utilization (ISRU) technologies to simplify processes and augment capabilities.

C. E. Gregg↗

NASA NTRS2016

Passive Water Assurance Delivery System

This report provides an analysis and evaluation of proposed design improvements to the internal water delivery system of NASA’s passive vegetable growing system. The VEGGIE system is designed to provide fresh vegetables and psychological benefits for astronauts aboard the International Space Station. Preliminary testing conducted by NASA for the VEGGIE system revealed flaws in the water delivery system. In these tests, the interface between the plants and the water reservoir failed to provide passive water delivery through the system both in microgravity experiments and experiments conducted on Earth. Our team’s goal was to fix this interface such that water can be passively delivered from the water reservoir to the plant rooting pillows to grow vegetative crops from seed to harvest. The system requirements outlined by NASA include: minimal total mass, on-demand passive water delivery, same dimensions as existing fixtures, minimal pressure on system to prevent leaking, zero mold growth, minimal swelling or clogging for non-flammable capillary materials, pressure stabilization between the water reservoir and plant pillow bags, even dispersal of water during initial priming, minimal bubble obstruction of capillary interface, maximum gas availability to plant roots, growth in a mixed artificial media (50:50 Arcillite:Fafard #2), and to avoid overwatering and drought conditions for plants. The major proposed design improvements are to use a single-interface capillary cord design to directly connect the water reservoir to the plant-rooting pillows, and to alter the water reservoir to model a propellant management device (PMD) in order to ensure consistent and long term watering for the VEGGIE system. The plant rooting pillow required minimal changes outside of replacing the capillary mat on the bottom of the pillow with O-ring insertion points the single-interface capillary system. - Research was conducted to determine which materials are able to uptake water through capillary action to grow Outredgeous Lettuce plants from seed to harvest. The primary requirements to be met by the team's design and evaluation of the capillary interface were: continuous passive watering for 90 days using non-flammable capillary materials and a peak water delivery rate of 30 mL/hr./0.15 m 2 . The results of the team's experimentation showed that the capillary material Nomex displayed the highest capillary water delivery potential with a maximum flow rate of 3.6 mL/hr. The Nomex capillary systems were the only capillary material to consistently grow Outredgeous Lettuce plants from seed to harvest, and displayed the highest average flow rate for multiple experiment sets. The Nomex material was previously incorporated into the VEGGIE system using a matted version of the capillary material, though the team recommends using a cord configuration in the single-interface capillary system for greater system stability. Nomex has proven to be a promising material, as it has passed both health and fire standards for use aboard the International Space Station. PMDs are made of materials that utilize surface tension and adhesive forces to overcome adverse accelerations to improve stability and ensure fluid delivery. PMDs are typically used in fuel tanks to ensure fuel delivery. The team recommends using a sponge PMD in order to mitigate bubble obstruction, decrease system weight, and ensure reliable water delivery to the capillary interface. The PMD water reservoir requires a rigid water reservoir and a vent tube for pressure stabilization. Since PMD’s cannot be tested in 1-G (Earth conditions), further theoretical modeling and testing is required for the proposed water reservoir design. The intent of this proposed system is to passively water plants in microgravity, though the technology is not limited to microgravity applications. The testing at The Ohio State University has proven that the design is highly effective on Earth, demonstrating that it could serve as a simple water delivery system in home and office applications. This would make vegetative crops more accessible in all indoor applications, thereby improving indoor air quality and occupant comfort. Additionally, this technology has great potential to be utilized in greenhouse plant production, cutting back on more sophisticated watering system energy and time requirements.

Alexandria Jensen↗

NASA NTRS2018

Food Sanitation Device for Use in Microgravity

EDEN is a transportation/orbital habitat that carries large amounts of crew members, food, and supplies from Earth to Mars and back, but can also act as a permanent, simulated-1g-environment space station in Martian orbit. The focus of the project is to create a temporary, but long-term living environment that focuses on human health and food production. The project is composed of four major habitable parts (in addition to other major components). Moving from the center out, the first is a central core that acts as a hub that connects to the structural spokes, the main propulsion rockets and serves as a place for other spacecraft to dock onto, in addition to housing some of the basic station control, navigation and automated computer systems. The second set of parts are the spokes that connect the ring to the central core; these are the primary structural components with elevators in the middle carrying people from the ring to the core. The ‘lower’ portions, near the ring and it’s 1g environment, also act as storage centers. The third part is the 2-story outer ring This project served as an engineering senior design project at Temple University, and as part of NASA’s eXploration and Habitation (X-Hab) 2018 Academic Innovation Challenge. The goal of the project was to design, construct, and test a device which would be used in microgravity to sanitize produce. This is part of a NASA’s effort to grow and sanitize fresh produce on the International Space Station (ISS), in order to provide more nutritious meal options to the astronauts. Our team designed a 3-D printed spherical device with UV-C LEDs lining the interior. The designed device consists of an 8” spherical chamber, 10 UV-C LEDs, and a touchscreen user interface to control the device. Our design meets the project requirements by offering several features: a simple user interface, minimal crew time to operate, no waste produced, and the ability to sanitize multiple types of produce. The main reductions in Salmonella bacteria and Aspergillus Flavus mold were not verified. However, the aerobic plate count requirement was greatly exceeded and validated. Testing of the device resulted in visual results confirming significant decrease in E. coli activity with increased UV-C exposure, as well as quantitative results confirming significant reduction in CFU/g for the aerobic plate count. These reductions achieved from 1.464 x 10 7 to 2 x 10 4 CFU/g (2.86 log reduction) after 5 minutes, were significantly more than the requirements given by NASA ( of the craft, which holds all of the food production along with medical bays, a control center and a few parks. This ring also integrates the rigid keystone modules, which are the interface between the spokes, the expandable-construction portions of the ring and the habitation pods. The keystone modules also incorporate redundant, distributed ECLSS systems, medical storage, airlocks, and other integral station functions. The last parts are the habitation pods; these hold the sleeping quarters along with the bathrooms, showers, kitchen space and lounge areas. These expandable modules latch onto the keystone modules of the ring, which serves as a circulatory link between the different habitation pods.

Damien Gordon↗

NASA NTRS2023

Propulsion-Airframe Integration for Conceptual Redesign of a Low-Boom Supersonic Transport

A low-boom supersonic transport was generated in a previous low-boom multidisciplinary optimization (MDO) study that used computational fluid dynamics (CFD) off-body pressure to compute the undertrack sonic boom ground signature and calibrated low-fidelity aerodynamics analyses to compute the mission performance metrics. This low-boom aircraft, referred to as the Mach 1.7 40-PAX concept, can carry 40 passengers for a low-boom overland mission with cruise Mach 1.7 for the airport pairs over the continental US and has the potential to achieve an undertrack sonic boom ground noise level below 70 perceived level of decibels at the start of overland cruise (SOC). The engine for the Mach 1.7 40-PAX concept was designed using the Numerical Propulsion System Simulation (NPSS) for the mission analysis and modeled as a flow-through nacelle for CFD-based sonic boom analysis. To understand how the engine plume affects the undertrack ground signature, the Mach 1.7 40-PAX concept is redesigned in this paper after replacing the flow-through nacelles by CFD engines for sonic boom analysis using aeropropulsive CFD simulation. A process is developed for approximation of the NPSS engine at SOC by a CFD engine for aeropropulsive CFD simulation. The generated CFD engine has the identical nozzle boundary conditions and approximately the same mass flow and thrust as those of the NPSS engine at SOC. Then, the outer mold line of the configuration with the CFD engines is redesigned to approximately restore the low-boom characteristics of the Mach 1.7 40-PAX concept at SOC. Finally, the CFD simulation data for the redesigned concept with the CFD engines is used to calibrate the low-fidelity aerodynamic analyses for mission analysis of this concept. The cyclic dependency of the involved disciplinary analyses is resolved using an iteration method for a consistent coupling of the mission analysis, NPSS engine analysis, and low-boom redesign using the aeropropulsive CFD simulation. This low-boom redesign study is used as an example to demonstrate how the propulsion-airframe integration could be implemented for conceptual design of supersonic transports that satisfy both the low-boom and mission performance requirements.

Low-boom supersonic transport↗

NASA NTRSDate not supplied

Design and Technology Maturation of the Stratospheric Projectile Experiment of Entry Dynamics

The supersonic and transonic dynamic stability of blunt-body reentry vehicles currently poses large risks in all of NASA’s ongoing entry missions (MSR SRL, MSR EES, and Dragonfly). These projects have allocated millions of dollars to testing and modeling efforts to buy down risk by using the current state-of-the-art (SoA) facilities at NASA’s disposal. While these facilities have heritage in supplying dynamics data to reentry missions, their availability is severely limited – particularly with the high number of concur-rent projects requesting simultaneous testing– and are costly when considering the science density per dollar. None of the current SoA facility methodologies allow the test model to have the dynamics fully develop through a flight relevant free-stream profile and as such require extrapolations with resultant high uncertainties in order to relate the test dynamics to flight expectations. SPEED is a NASA Ames Center Innovation Fund (CIF) project that is developing a highly tailorable and cost-effective test methodology to better assess the dynamic stability of blunt-body reentry vehicles via a stratospheric balloon flight. This is accomplished by dropping a suite of instrumented capsules from a stratospheric balloon to gain a statistically relevant dataset of scaled reentry vehicles in mission relevant free-flight conditions. This presentation will walk through how the test methodology is being implemented specifically for the Mars Sample Return (MSR) Earth Entry System (EES) geometry in an awarded Flight Opportunities Program (FOP) test flight in early CY24. SPEED Application to MSR: SPEED consists of three main mechanical systems: the Drop Platform, the Projectile, and the test Capsule. SPEED is being developed as a set of guidelines and recommendations for how to test with the proposed Concept of Operations (Conops) since the specific design parameters will vary depending on the specific project’s reference trajectory and entry vehicle design. As such, this presentation will walk through the development time-line as shown in Fig. 2. This is meant to serve as a blueprint for further missions as desired. Mechanical and Avionics Design. The SPEED test platform designed for the MSR-EES capsule geometry with nominal entry parameters has the ability to carry 10 Capsules to altitude instrumented with: 1. 3-Axis Accelerometer 2. IMU 3. Gyroscope 4. Magnetometer 5. Pressure Transducer cruciform 6. Uplook and Horizon Cameras To package the avionics/instrumentation suite, the capsule is approximately 1’ in diameter with the Outer Mold Line (OML) centroid-scaled from the full EES design. The internal volume is gutted and custom-shaped to fit the desired instrumentation suite, as well as to allow for the positioning of ballast mass such that the Center of Gravity is analogous to the flight vehicle. All structural components in the Capsule and Projectile are 3D printed, which significantly reduces the cost of each flight unit to around $1500 including all instrumentation, avionics, and structural components. Flight Conops. The test Capsule is accelerated to the desired altitude and Mach number while stowed in the Projectile, a missile-like vehicle consisting of steel ballast in the nose, a low-drag OML, and an Ejection Mechanism to reliably release the Capsule into the free-flow supersonic conditions. For the MSR-EES design, the capsule employs ~3kg of ballast mass at the nose to accelerate the 1.25kg test Capsule to ~Mach 1.7 at 23km altitude. This requires an initial release altitude of 40km, the quoted limit of a 80kg payload by the FOP-contracted balloon provider. Once the Ejection Mechanism avionics detect the proper conditions, the spring-loaded Ejection Mechanism will release and – guided by the sabot – expose the test Capsule to the desired test conditions for ~5 seconds of free-flight in the supersonic/transonic regimes. Dynamics in the subsonic regime will also be captured with the instrumentation suite with post-flight recovery operations aimed at recovering the high-G-load capable SD cards after the planned hard impact landings. Testing and Development: In the few months the SPEED project has worked the development of MSR-EES flight test, the team has performed lab and drone based testing which this presentation will overview. After the first design phase, the team fabricated Engineering Demonstration Units (EDUs) of all subsystems to perform validation testing shown in Fig. 5. After validation was completed on the subsystem level, a drone-drop test was performed at the recreational flight ceiling of 400ft altitude to assess the SPEED systems in a flight environment. Parameters such as in-flight stability, hard impact landing performance, and avionics performance were quantified and qualified. The FY23 CIF will culminate in a helicopter drop test aboard an Air National Guard Blackhawk. This will prepare the team for the CY24 FOP stratospheric balloon flight that should provide the final verification to begin offering the test platform for mission support. Focus of Presentation: This presentation will outline the technology maturation path of the SPEED implementation to the MSR-EES capsule baseline as well as the details regarding the mechanical system, avionics and instrumentation, and flight operations. Note that a complementary presentation is being submitted for a methodology overview of the SPEED test platform, introducing the testing technique and benefits as well as the full application space of the technology.

pitch damping coefficient↗

NASA NTRSDate not supplied

Overview of Additively Manufactured TPS Proposed Flight Test and Earth Re-Entry Capsule Design

A flight mechanics overview is presented of an Earth flight test designed to investigate a novel, 3D printed thermal protection system (TPS) that is currently in development at NASA as part of the Additive Manufacturing of Thermal Protection Systems project. The project is pioneering a method to print a thermal protection system onto an entry vehicle forebody one layer at a time. This method reduces labor and complexity as compared to traditional manufacturing methods while increasing mission-dependent customization of through-depth materials properties. The flight test has three objectives. First, subject the forebody stagnation point of a capsule equipped with additively manufactured TPS (AMTPS) material to peak heat fluxes in excess of 100 $W/cm^2$. Second, capture in-flight data to enable flight reconstruction and AMTPS material thermal response model improvement. Third, recover the capsule with data storage and forebody AMTPS intact to enable post-flight inspection and analysis of AMTPS performance. The flight test trajectory is designed to achieve a peak stagnation point, cold-wall, entry heat flux of 135~$W/cm^2$. Flight mechanics simulations are performed using the Program to Optimize Simulated Trajectories II (POST2) and Monte-Carlo analysis yields statistical percentiles on vehicle performance at key points along the trajectory. Based on the flight mechanics analysis presented in this paper, a prototype capsule was designed, partially fabricated, and underwent preliminary component stress testing in preparation for fabrication of the flight unit capsule. The capsule outer mold line is a modified version of the heritage Mars Microprobe geometry. The capsule has a 0.356~m diameter, a 30~kg mass, and a hypersonic ballistic coefficient of 300~$kg/m^2$. Sensor selection is guided by flight dynamics simulations with the goal of resolving the re-entry heating pulse. On-board instrumentation include forebody and aftbody pressure sensors and thermocouples, a 9-axis IMU, a GPS receiver, and an Iridium satellite modem, all of which collect and store data throughout flight via on-board avionics systems. A two-stage parachute system is designed to decelerate the capsule to touchdown velocities that will not result in significant fracture or deformation of the charred AMTPS material at ground impact.

Flight Mechanics↗

NASA NTRSDate not supplied

Strategies for Determining Safety of Fermented Foods Produced in Space

The BioNutrients experiments examine the feasibility of using microbially produced foods – yogurt, kefir, fermented food products– to supplement the current prepackaged food system to provide freshly synthesized nutrients and genetically engineered protein therapeutics to support crew health for sustainable and long duration crewed exploration. Safety of the products must be established as direct consumption of such products is a risk due to potential contamination with pathogenic organisms. Identifying pathogen contamination is particularly challenging as the fermenting cultures can mask the presence of contaminating organisms. Here we consider current methods of detecting coliforms, aerobic colonies, non-lactic acid bacteria, molds (yeasts), and specific pathogens including Staphylococcus aureus and salmonella. We also consider alternate and additional testing including sequencing and quantitative PCR. We investigate the use of the E-Nose developed by NASA Ames Research Center. This portable device senses volatile organic compounds in real time and can be trained to recognize “good” uncontaminated products from contaminated ones as a means of predicting food safety. Finally, we consider methods of in-flight pasteurization to increase safety and decrease overall microbial load of these products. This presentation will summarize testing status and outline the strategy that will be employed in the BioNutrients-3 ISS fermented foods experiment.

Natalie Ball↗

NASA NTRS2024

Evaluating Liftoff Debris for NASA’s Space Launch System (SLS) Prior to the Artemis I Launch

The SLS Artemis I launch vehicle is the first of several planned Artemis launch vehicles, with a number of design differences from earlier NASA missions that incur liftoff debris risk to the mission. As a test vehicle, the Artemis I hardware also endured environments and tests not planned for future missions, which led to several additional factors contributing to an evolving liftoff debris risk to the SLS vehicle. This paper will summarize these risk factors and address the processes used to evaluate and communicate the risks to support a successful Artemis I launch. It will discuss how the evolving risks that were quantified and evaluated by a Cross-Program team of debris Subject Matter Experts to mitigate liftoff debris hazards and communicate updated risk to the SLS vehicle. This process was performed through the inaugural use of an SLS debris day-of-launch (DOL) standard operating procedure that will be used for subsequent Artemis missions. This paper addresses the risk of liftoff debris, debris released by the vehicle or from the launch pad during liftoff through vehicle tower clear. Expected liftoff debris is well understood from previous NASA programs’ experience and from tests of materials, processes and functions that are known to release liftoff debris. These expected sources were assessed and cleared well ahead of launch day. However, given the ever-changing schedules and environments, processes were in place to evaluate any additional potential liftoff debris risks identified during launch countdown. Although many of the Artemis vehicle hardware components are similar to those on the NASA Shuttle Program, there are important differences in the architecture of the Artemis I vehicle which require new assessments of liftoff debris risk for the Artemis missions. The more favorable Artemis crew module location and surfaces are far less vulnerable to debris impacts; however, the longer vehicle can result in higher liftoff debris impact energies to those components on the aft end of the vehicle. Additionally, the positional change of the RS-25 liquid engines to nearer the Booster nozzle exit plane along with the change in Booster throat plug design is a disadvantage to the overall liftoff debris risk which resulted in additional test and analysis efforts for evaluating the integrated vehicle debris risk. In spite of the comprehensive tests and analyses of Artemis I expected liftoff debris, a number of additional tests/processes were completed prior to the Artemis I mission that were required to support a complete understanding of a new launch vehicle, but increased the risk of releasing liftoff debris. The hardware endured several additional cryogenic loading cycles, including the Green Run tests at Stennis Space Center, Wet Dress Rehearsals at Kennedy Space Center, and multiple launch attempts. Each of these cycles induced stresses in the thermal protection system (TPS) materials, increasing the risk of damage to and release of the TPS. Additionally, induced and weather environmental factors that could increase the likelihood of debris release were significant. Vibrations and stresses in the TPS were induced by a required roll-back to the Vehicle Assembly Building before Hurricane Ian to protect the vehicle from damage by high winds. Wind damage and potential internal stresses to several outer mold line materials on the integrated SLS vehicle and mobile launcher were caused by weathering Hurricane Nicole at Pad 39B the week before launch. A thorough imagery scan of the vehicle was performed after each event and the damage observed was repaired, removed, or assessed and the risk to the mission evaluated. Mitigation of debris risk can occur by tests and analyses to show debris impacted components as damage tolerant, by new/improved processes for prevention of debris availability, or redesign. Risk mitigation processes for Artemis I-specific liftoff debris events and the development and use of the SLS debris day of launch (DOL) procedures that will be used for subsequent Artemis missions will be described.

Space Launch System↗

NASA NTRSDate not supplied

Development of Subsonic Single Aft Engine (SUSAN) Attritable Research Vehicle (SARV) Wing Structure

This paper introduces a high-level overview of the design and development of the SUbsonic Single Aft eNgine (SUSAN) Attritable Research Vehicle (SARV) wing structure. Unique design considerations were made for the structural layout of the wing to include storage for batteries, distributed electric engines, and the requirement for the wing to be shippable in a cargo box. The wing structure development process will be discussed including the wing internal structure design evolution, the fabrication of the manufacturing demonstration vehicle, wing outer mold line design, integration of wing internal structure and wing skins, and finally integration of the wing with the fuselage structure. Additionally, the development of the wing skin design will be discussed while highlighting the wing skin manufacturing demonstration panels as well as composite testing for material characterization purposes.

wing structure↗

NASA NTRSDate not supplied

XRF Characterization of MMOD Impact Damage

Introduction The Hypervelocity Impact Technology (HVIT) Group at the NASA Johnson Space Center (JSC) has performed over 150 post flight MMOD inspections on returned space-ex-posed hardware and collected over 1,600 samples. Determination of the impactor source typically requires an analysis of the projectile residue in the damage feature. At this time, about 20% of the samples have been processed. Types of Samples Samples in the HVIT group collection can be classified into two types. Indirect (non-destructive) samples are produced when a pliable material (e.g., adhesive tape or dental mold) is inserted into an impact feature. With this type of sampling technique, crater material and (hopefully) projectile residue material is embedded in the sample media and can detected using further chemical characterizing techniques. Direct (destructive) sampling involves the in-tact extraction of material from the spacecraft and is done in a manner that the entire impact feature can be excised intact. This technique provides the greatest chance of successfully determining impactor source due to the entirety of the projectile remnants being present within the collected sample. Updated Projectile Residue Detection Techniques Previous assessments of projectile provenance have involved the use of samples that are first mounted in epoxy, sectioned to expose the crater interior, imaged with a scanning electron microscope (SEM), then any observed impactor residue was then analyzed using an energy dispersive spectrometer (EDS). This technique, while proven, may be supplemented with other types of elemental analysis techniques that can observe major element chemistry, in order to improve throughput of sample analysis. The Astromaterials Research and Exploration Science (ARES) Division at JSC, for example, operates a Bruker M4 Tornado micro-X-Ray fluorescence (XRF) spectrometer, capable of creating elemental maps of areas around these small impact features in a couple of hours, with a spot size <20 μm. The potential advantage with this technique lies in sample preparation, as no polishing or conductive coatings are needed. Early trials attempted to deter-mine impactor composition by collecting spectra from intact samples by aiming the X-Rays directly into the impact feature, but the signal:noise ratio was too low for confident material identification. Sample preparation for XRF then relies on sectioning the samples parallel to the impactor trajectory in order to expose the largest area of subsurface damage possible, thus maximizing the signal from any small impactor remnants. Complementary to the use of XRF for sample analysis, ARES also houses a Nikon XTH 320 micro-X-Ray computed tomography (XCT). This instrument can be used to create 3D visualizations of impact damage for the determination of crater volumes and dimensions, as well as for the determination of the best place to section each sample for the subsequent XRF analysis.

J L Hyde↗