SEARCH · Engineering Papers

Results for “Land Use Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Shuttle navigation overview

Space Shuttle onboard navigation system tasks are related to position and velocity determination, attitude determination, sensor management, sensor Redundancy Management (RM), and navigation-related functions such as transformations, timing system utilization, and user processing for displays, guidance, and flight control. It is pointed out that Shuttle navigation is different in at least two areas from previous manned space flight navigation. The differences are related to the use of multiple units to provide protection from increased risk of failure of off-the-shelf-type equipment used for more than one flight, and the need to land at a runway. Attention is given to the navigation sensor system, the Shuttle Inertial Measurement Units, the Shuttle Star Tracker, the Crew Optical Alinement Sight, the Shuttle Tacan, the Air Data Subsystem, and aspects of navigation system mechanization.

Savely, R. T.↗

NASA NTRS1992

Piloted simulator investigations of a civil tilt-rotor aircraft on steep instrument approaches

NASA-Ames has used its Vertical Motion Simulator to investigate steep-glideslope instrument approaches for a civil transport tilt-rotor aircraft in two different cases: (1) where pilots used raw glideslope and localized error data for 6-25 deg slopes, terminating in slow roll-on landings, and (2) where a flight director commanded manual conversion from fixed-wing to helicopter modes and a deceleration on the glideslope led to a vertical landing on a small urban helipad. In the former, there occurred control problems directly ascribable to the slow approach speed; in the latter, the four-cue flight director's cockpit augmentation furnished adequate pilot ratings up to 15-deg glideslope.

Decker, William A.↗

NASA NTRS1998

Upper Limits of Predictability in Long-Range Climate/Hydrologic Forecasts

The accurate forecasting of el nino or la nina conditions in the tropical Pacific can potentially lead to valuable predictions of hydrological anomalies over land at seasonal to interannual timescales. Even with highly accurate earth system models, though, our ability to generate these continental forecasts will always be limited by the chaotic nature of the atmospheric circulation. The nature of this fundamental limitation is explored through the use of 16-member ensembles of multi-decade GCM simulations. In each simulation of the first ensemble, sea surface temperatures (SSTs) are given the same realistic interannual variations over a 45-year period, and land surface state is allowed to evolve with that of the atmosphere. Analysis of the results shows that the SSTs control the temporal organization of continental precipitation anomalies to a significant extent in the tropics and to a much smaller extent in midlatitudes. In each simulation of the second ensemble, we prescribe SSTs as before, but we also prescribe interannual variations in the low frequency component of evaporation efficiency over land. Thus, in the second ensemble, we effectively make the extreme assumption that surface boundary conditions across the globe are perfectly predictable, and we quantify the consistency with which the atmosphere (particularly precipitation) responds to these boundary conditions. The resulting "absolute upper limit" on the predictability of precipitation is found to be quite high in the tropics yet only moderate in many midlatitude regions.

Koster, R. D.↗

NASA NTRS2002

Robosphere1: Building A Self-Sustaining Robotic Ecology for Mars Exploration

Robotic exploration of Mars has been a "one shot" approach where each surface mission is planned typically with a rover that will perform a series of experiments for a few weeks or months, until the robot becomes unable to operate in the harsh Mars conditions and simply "dies". It would clearly be desirable to have robots on Mars that can last for much longer periods of time, I propose that there is an approach to sustained robotic exploration that can also pave the way to future human presence. The idea is to continue building a robotic infrastructure with every mission we send. The approach is to built a team of modular robots that could repair individual members when they break down. We could "seed" areas of interest with sturdy power stations (solar, chemical) that teams of robots could use to recharge themselves. We could also seed parts and modules the robots could access for self-repair. No mission could really "fail" if we simply keep adding to and maintaining the existing infrastructure. Simply landing a package of parts will be a success. In time we create a loose infrastructure that can be controlled and augmented from earth on a continuing basis, and which could eventually pave the way for human exploration. I propose that we could begin to build this infrastructure from relatively simple modular robots. Imagine 2 "spider-like" robots built out of small modular snap-in pieces, a bin of these pieces and a bin of snap-in end effectors. One of the spiders breaks down, i.e. one of its modules needs to be replaced. The second spider comes to the rescue and helps the first one replace the broken module. Assuming the input of fresh modules, this process can continue indefinetly. Now start separating robotic explorers from robotic "mechanics", start adding, a category of mechanics that are able to fix at least some of the broken modules (and which in turn can be fixed by the original mechanics), The need for a fresh influx of modules is thus reduced. I submit that we could bootstrap a robotic ecology until it needs very little material from earth and can rely mostly on in-situ resources., We can experiment with this concept in an earthbound facility that can also simulate Mars conditions. I propose that we call this facility Robosphere1.

Colombano, Silvano P.↗

NASA NTRS1961

Subsonic Longitudinal Aerodynamic Characteristics of Disks with Elliptic Cross Sections and Thickness-Diameter Ratios from 0.225 to 0.425

General interest in manned space flight has provided a stimulus for the investigation of shapes which appear to be attractive for application to re-entry vehicles. Such vehicles can be classed as either nonlifting or lifting. Nonlifting types, such as used in Project Mercury, have certain advantages which include structural simplicity, no requirement for an elaborate flight-control system, ease of mating with the booster, and short exposure times to high heating rates during entry. Advantages of lifting types, by comparison, include lower peak heating rates and decelerations, the possibility for a conventional horizontal landing, and the ability to maneuver, thus providing control over longitudinal and lateral range and a wider entry corridor on return from planetary or lunar missions. A lifting shape which appears attractive in terms of the considerations is a thick disk. At high attitudes, the weight to drag ratio is low and the radius of curvature of the surface exposed to the airstream is large, a combination of parameters which results in reduced convective heating rates. The low-speed lift-drag ratios associated with this type of shape appear sufficiently high to permit a conventional horizontal landing. The investigation reported herein was undertaken to assess the effects of thickness on the aerodynamic characteristics of disk shapes suitable for lifting re-entry into the earth's atmosphere and potentially capable of conventional horizontal landing. The models had elliptic cross sections which varied in thickness from 0.225 to 0.425 diameter. The tests were conducted in the Ames 12-Foot Pressure Wind Tunnel over a Mach number range from 0.25 to 0.90 at a Reynolds number of 3.3x10 (exp 6) and at Reynolds numbers to 16x10 (exp 6) at a Mach number of 0.25. Tests on similar shapes have been conducted at subsonic, transonic, and supersonic speeds and the results have been presented.

Demele, Fred A.↗

NASA NTRS2010

The ICESat-2 Laser Altimetry Mission

Satellite and aircraft observations have revealed that remarkable changes in the Earth s polar ice cover have occurred in the last decade. The impacts of these changes, which include dramatic ice loss from ice sheets and rapid declines in Arctic sea ice, could be quite large in terms of sea level rise and global climate. NASA's Ice, Cloud and Land Elevation Satellite-2 (ICESat-2), currently planned for launch in 2015, is specifically intended to quantify the amount of change in ice sheets and sea ice and provide key insights into their behavior. It will achieve these objectives through the use of precise laser measurements of surface elevation, building on the groundbreaking capabilities of its predecessor, the Ice Cloud and Land Elevation Satellite (ICESat). In particular, ICESat-2 will measure the temporal and spatial character of ice sheet elevation change to enable assessment of ice sheet mass balance and examination of the underlying mechanisms that control it. The precision of ICESat-2's elevation measurement will also allow for accurate measurements of sea ice freeboard height, from which sea ice thickness and its temporal changes can be estimated. ICESat-2 will provide important information on other components of the Earth System as well, most notably large-scale vegetation biomass estimates through the measurement of vegetation canopy height. When combined with the original ICESat observations, ICESat-2 will provide ice change measurements across more than a 15-year time span. Its significantly improved laser system will also provide observations with much greater spatial resolution, temporal resolution, and accuracy than has ever been possible before.

Abdalati, Waleed↗

NASA NTRS2012

Acoustic Surveys of a Scaled-Model CESTOL Transport Aircraft in Static and Forward Speed Conditions

An 11% scale-model of a Cruise-Efficient Short Take-off and Landing (CESTOL) scalemodel test was recently completed. The test was conducted in the AEDC National Full-Scale Aerodynamic Complex (NFAC) 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The model included two over-wing pod-mounted turbine propulsion simulators (TPS). The hybrid blended wing-body used a circulation control wing (CCW) with leadingand trailing-edge blowing. The bulk of the test matrix included three forward velocities (40 kts, 60 kts, and 100kts), angle-of-attack variation between -5 and 25 , and CCW mass flow variation. Seven strut-mounted microphones outboard of the left wing provided source directivity. A phased microphone array was mounted outboard of the right wing for source location. The goal of this paper is to provide a preliminary look at the acoustic data acquired during the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) test for 0 angle-of-attack and 0 sideslip conditions. Data presented provides a good overview of the test conditions and the signal-to-noise quality of the data. TPS height variation showed a difference of 2 dB to 3 dB due to wing shielding. Variation of slot mass flow showed increases of 12 dB to 26 dB above the airframe noise and the TPS increased the overall levels an additional 5 dB to 10 dB.

Burnside, Nathan↗

NASA NTRS2015

Overview of Stirling Technology Research at NASA Glenn Research Center

Stirling Radioisotope Power Systems (RPS) are under development to provide power on future space science missions where robotic spacecraft will orbit, flyby, land or rove using less than a quarter of the plutonium the currently available RPS uses to produce about the same power. Glenn Research Center's (GRC's) newly formulated Stirling Cycle Technology Development Project (SCTDP) continues development of Stirling-based systems and subsystems, which include a flight-like generator and related housing assembly, controller, and convertors. The project also develops less mature technologies under Stirling Technology Research, with a focus on demonstration in representative environments to increase the technology readiness level (TRL). Matured technologies are evaluated for selection in future generator designs. Stirling Technology Research tasks focus on a wide variety of objectives, including increasing temperature capability to enable new environments, reducing generator mass and/or size, improving reliability or system fault tolerance, and developing alternative designs. The task objectives and status are summarized.

robotics↗

NASA NTRSDate not supplied

X-57 High-Lift Propeller Control Schedule Development

The NASA X-57 distributed electric propulsion flight demonstrator uses a high-lift propeller system to maintain low-speed capability with a highly loaded, cruise-efficient wing. Previous research showed that the control scheme for the high-lift propellers was a crucial factor to enable an adequate balance between stabilized glideslope control and appropriate lift margin during the approach-to-landing phase of flight. This paper expands the high-lift propeller control considerations to include all phases of low-speed flight, including preflight, taxi, takeoff, initial climb, approach, and landing. Two control modes, termed airspeed and fixed mode, are developed in this paper. The airspeed mode varies propeller torque based on equivalent airspeed to account for different phases of ground and flight operations. The fixed mode operates the high-lift propeller system at a fixed rotational speed to account for failures in the air data system, preflight checkout, and high-performance takeoff operations. Modeling of the high-lift propellers within the X-57 low-speed flight envelope shows that (1) the structural rotational speed limit of the propeller blades limits their effectiveness at higher altitudes and airspeeds, (2) the speed setting of the fixed mode is set by the maximum torque of the airspeed mode, and (3) minimizing the potential for windmilling in non-standard conditions sets the torque schedule at higher speeds. Additionally, the fixed mode is shown to provide an increased climb rate during normal takeoff operations.

Nicholas K. Borer↗

NASA NTRSDate not supplied

Modified Cascading Generalized Inverse Control Allocation

The current aviation revolution towards electric propulsion aircraft (e.g., electric vertical takeoff-and-landing) brings unique control challenges. These vehicles are typically over-actuated (more effectors than desired control outcomes), may require control strategies for the three phases of flight (hover, transition and cruise), and currently have limited electric power availability. These vehicle challenges bring the need for optimal control allocation to the forefront of research. A leading control allocation algorithm, used in current flight vehicles, is the Cascading Generalized Inverse (CGI). Unfortunately, the Cascading Generalized Inverse algorithm is unable to achieve some desired outcomes, it intermittently provides non-optimal allocations, and it may fail to preserve moment direction near maximal achievable outcomes. In this research, the shortcomings of the Cascading Generalized Inverse algorithm are addressed by augmenting the algorithm with Scalar Difference Quadratic unsaturation identification and location at each iteration. Rigorous theory is shown that the Modified Cascading Generalized Inverse performs better at obtaining optimal allocations for all attainable outcomes. Numerical case studies for over-actuated vehicles demonstrate resolution to the aforementioned deficiencies.

Control Allocation↗

NASA NTRSDate not supplied

Modified Cascading Generalized Inverse Control Allocation

Control Allocation↗

NASA NTRS2023

X-57 Mod IV Avionics Power Analysis

The X-57 Mod IV Avionics Power Analysis was developed to provide the design requirements for the X-57 Mod IV Avionics Power System. In the Mod IV configuration, twelve 13kW high lift motors and motor controllers are distributed along the leading edge of the Mod III carbon fiber wing to assist with lift during takeoff and landing. These motors are turned off during the cruise phase of the flight. A high voltage traction battery (460 VDC nominal) supplies power for the high lift motors. The Mod IV avionics power design uses the Mod II and Mod III power architecture as a baseline. Please see the Mod II Avionics Power Analysis (ANLYS-CEPT-020) for a description of the Mod II and Mod III avionics power design.

Franklin Harris↗

DOE OSTI2022

Patterns and controls on island-wide aboveground biomass accumulation in second-growth forests of Puerto Rico

This dataset includes two products from Martinuzzi et al. (2022): "biomass.tif" is a 26-m resolution forest biomass (AGB) map for Puerto Rico derived from NASA G-LiHT lidar data and forest inventory data (FIA plots), in raster format. "input_multivariate_v2.shp" is a point shapefile with information on forest age, substrate, past land use, topographic wetness, slope, and precipitation, for each forest pixel. These two datasets can be used to evaluate spatial patterns of AGB in second-growth forests across transects of lidar data in humid forests of Puerto Rico, and to analyze relationship(s) between AGB and environmental variables. Additional information on these products can be found on the supporting file called "Readme.txt" included within the data archive, as well as in the original manuscript by Martinuzzi et al (2022).

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1987

STOL landing thrust: Reverser jet flowfields

Analysis tools and modeling concepts for jet flow fields encountered upon use of thrust reversers for high performance military aircraft are described. A semi-empirical model of the reverser ground wall jet interaction with the uniform cross flow due to aircraft forward velocity is described. This ground interaction model is used to demonstrate exhaust gas ingestion conditions. The effects of control of exhaust jet vector angle, lateral splay, and moving versus fixed ground simulation are discussed. The Adler/Baron jet-in-cross flow model is used in conjunction with three dimensional panel methods to investigate the upper surface jet induced flow field.

Kotansky, D. R.↗

NASA NTRS2019

Regolith Particle Erosion of Material in Aerospace Environments

This paper studies the effect of exposing thermal control S13GP:6N/LO-I white paint, Kapton flex cable, fiber optic cable, HEPA filter, and M55J graphite composite to high-velocity regolith environment that spacecraft landing on Mars are commonly exposed to. Due to the similarity between the Mars 2020 Rover design and Mars Science Laboratory design, it is expected that the Mars 2020 rover will be exposed to a similar high-speed regolith environment that the Mars Science Laboratory was exposed to. This environment is replicated to test the survivability of susceptible materials. The testing is performed at the University of Dayton Research Institute in Dayton, Ohio. The experiments expose different materials to basaltic–like particles ranging in size from approximately 40 μm to 2 cm, at velocities ranging from 19 m/s to 250 m/s, with varied particle fluxes (measured in mg/cm2). Depending on the size of the particle used, the particles can either embed in or erode the material. Posttest analysis shows that all materials tested will survive the expected environment observed during the Mars 2020 landing event. Some materials are tested to failure in order to better characterize material response. Materials that fail in some test scenarios include the paint, fiber optic cable, and the graphite composite. After being exposed to regolith, the α/ε ratio of the paint increased by ~37% due to particles embedding in the paint. Darkening of the paint can negatively affect thermal control of the rover. With high particle mass fluxes, the paint eventually degraded enough to expose the aluminum substrate. When impacted by a 1.5 cm particle traveling at 20 m/s, the fiber optic cable did not sever, but the impact did cause the cable to deform enough to crack the glass, which resulted in a significant increase in attenuation, rendering the cable unable to transmit data. The graphite composite also failed when exposed to high particle fluxes. All of the observed failures occurred for test cases above the expected landing environment with significant margin. Tests performed beyond the requirements help characterize how well these materials will survive in even more extreme environments for future missions.

Abid, Mohamed↗

DOE OSTI2015

Identifying multiscale zonation and assessing the relative importance of polygon geomorphology on carbon fluxes in an Arctic tundra ecosystem

Abstract We develop a multiscale zonation approach to characterize the spatial variability of Arctic polygonal ground geomorphology and to assess the relative controls of these elements on land surface and subsurface properties and carbon fluxes. Working within an ice wedge polygonal region near Barrow, Alaska, we consider two scales of zonation: polygon features (troughs, centers, and rims of polygons) that are nested within different polygon types (high, flat, and low centered). In this study, we first delineated polygons using a digital elevation map and clustered the polygons into four types along two transects, using geophysical and kite‐based landscape‐imaging data sets. We extrapolated those data‐defined polygon types to all the polygons over the study site, using the polygon statistics extracted from the digital elevation map. Based on the point measurements, we characterized the distribution of vegetation, hydrological, thermal, and geochemical properties, as well as carbon fluxes, all as a function of polygon types and polygon features. Results show that nested polygon geomorphic zonation—polygon types and polygon features—can be used to represent distinct distributions of carbon fluxes and associated properties, as well as covariability among those properties. Importantly, the results indicate that polygon types have more power to explain the variations in those properties than polygon features. The approach is expected to be useful for improved system understanding, site characterization, and parameterization of numerical models aimed at predicting ecosystem feedbacks to the climate.

Wainwright, Haruko M.↗

DOE OSTI2014

Regionalization of subsurface stormflow parameters of hydrologic models: Derivation from regional analysis of streamflow recession curves

Not Available

Ye, Sheng↗

DOE OSTI2015

Leaf respiration ( GlobResp ) - global trait database supports Earth System Models

Here we detail how Atkin and his colleagues compiled a global database (GlobResp) that details rates of leaf dark respiration and associated traits from sites that span Arctic tundra to tropical forests. This compilation builds upon earlier research (Reich et al., 1998; Wright et al., 2006) and was supplemented by recent field campaigns and unpublished data.In keeping with other trait databases, GlobResp provides insights on how physiological traits, especially rates of dark respiration, vary as a function of environment and how that variation can be used to inform terrestrial biosphere models and land surface components of Earth System Models. Although an important component of plant and ecosystem carbon (C) budgets (Wythers et al., 2013), respiration has only limited representation in models. Seen through the eyes of a plant scientist, Atkin et al. (2015) give readers a unique perspective on the climatic controls on respiration, thermal acclimation and evolutionary adaptation of dark respiration, and insights into the covariation of respiration with other leaf traits. We find there is ample evidence that once large databases are compiled, like GlobResp, they can reveal new knowledge of plant function and provide a valuable resource for hypothesis testing and model development.

54 ENVIRONMENTAL SCIENCES↗