Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INTERMEDIATE COUPLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Ammonia-fed reversible protonic ceramic fuel cells with Ru-based catalyst

Abstract The intermediate operating temperatures (~400–600 °C) of reversible protonic ceramic fuel cells (RePCFC) permit the potential use of ammonia as a carbon-neutral high energy density fuel and energy storage medium. Here we show fabrication of anode-supported RePCFC with an ultra-dense (~100%) and thin (4 μm) protonic ceramic electrolyte layer. When coupled to a novel Ru-(BaO) 2 (CaO)(Al 2 O 3 ) (Ru-B2CA) reversible ammonia catalyst, maximum fuel-cell power generation reaches 877 mW cm −2 at 650 °C under ammonia fuel. We report relatively stable operation at 600 °C for up to 1250 h under ammonia fuel. In fuel production mode, ammonia rates exceed 1.2 × 10 −8 NH 3 mol cm −2 s −1 at ambient pressure with H 2 from electrolysis only, and 2.1 × 10 −6 mol NH 3 cm −2 s −1 at 12.5 bar with H 2 from both electrolysis and simulated recycling gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2010

Light neutralinos with large scattering cross sections in the minimal supersymmetric standard model

Motivated by recent data from CoGeNT and the DAMA annual modulation signal, we discuss collider constraints on the minimal supersymmetric standard model neutralino dark matter with mass in the 5-15 GeV range. The lightest superpartner (LSP) would be a bino with a small Higgsino admixture. Maximization of the dark matter nucleon scattering cross section for such a weakly interacting massive particle requires a light Higgs boson with tan{beta} enhanced couplings. Limits on the invisible width of the Z boson, combined with the rare decays B{sup {+-}{yields}{tau}{nu},} and the ratio B{yields}D{tau}{nu}/B{yields}Dl{nu}, constrain cross sections to be below {sigma}{sub n} < or approx. 5x10{sup -42} cm{sup 2}. This indicates a higher local dark matter density than is usually assumed by a factor of roughly 6 necessary to explain the CoGeNT excess. This scenario also requires a light charged Higgs boson, which can give substantial contributions to rare decays such as b{yields}s{gamma} and t{yields}bH{sup +}. We also discuss the impact of Tevatron searches for Higgs bosons at large tan{beta}.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2010

Asymmetric left-right model and the top pair forward-backward asymmetry

The forward-backward asymmetry measurement in top-pair production at the Tevatron is about 2{sigma} from the standard model prediction. We propose an asymmetric left-right model, which includes a W{sup '} boson with a right-handed coupling of down to top quark, and a Z{sup '} boson with diagonal couplings to the up, top, and down quarks with M{sub W}{sup '{approx_equal}}175 GeV and M{sub Z}{sup '{approx_equal}}900 GeV. The model accounts for the asymmetry while remaining consistent with the top-pair total cross section and invariant mass distribution.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2011

Methods for studying the coherent 4D structural dynamics of free molecules and condensed state of matter

Studies in the coupled 4D spatial and temporal continuum are necessary for understanding the dynamic features of molecular systems with a complex profile of the potential energy surface. The introduction of time sweep into diffraction methods and the development of principles for studying coherent processes have revealed new approaches to the analysis of the dynamics of wave packets, the intermediate products and the transition state of the reaction center, and short-lived compounds in gaseous and condensed media. The use of picosecond and femtosecond electron probe pulses, synchronized with excitation laser pulses, determined the development of ultrafast electron crystallography, time-resolved X-ray diffraction, and dynamic transmission electron microscopy (DTEM). One of the most promising applications of the developed diffraction methods is the characterization and visualization of the processes occurring upon the photoexcitation of free molecules and biological objects and the analysis of surface and thin films. The whole set of spectral and diffraction methods based on different physical principles, which are complementary and make it possible to perform the photoexcitation of nuclei and electrons and carry out diagnostics of their dynamics at ultrashort time sequences, reveal new possibilities for studies with the necessary integration of the 'structure-dynamics-function' triad in chemistry, biology, and materials science.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Technique for enhancing the power output of an electrostatic generator employing parametric resonance

A circuit-based technique enhances the power output of electrostatic generators employing an array of axially oriented rods or tubes or azimuthal corrugated metal surfaces for their electrodes. During generator operation, the peak voltage across the electrodes occurs at an azimuthal position that is intermediate between the position of minimum gap and maximum gap. If this position is also close to the azimuthal angle where the rate of change of capacity is a maximum, then the highest rf power output possible for a given maximum allowable voltage at the minimum gap can be attained. This rf power output is then coupled to the generator load through a coupling condenser that prevents suppression of the dc charging potential by conduction through the load. Optimized circuit values produce phase shifts in the rf output voltage that allow higher power output to occur at the same voltage limit at the minimum gap position.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2014

Nonadiabatic dynamics of electron transfer in solution: Explicit and implicit solvent treatments that include multiple relaxation time scales

The development of efficient theoretical methods for describing electron transfer (ET) reactions in condensed phases is important for a variety of chemical and biological applications. Previously, dynamical dielectric continuum theory was used to derive Langevin equations for a single collective solvent coordinate describing ET in a polar solvent. In this theory, the parameters are directly related to the physical properties of the system and can be determined from experimental data or explicit molecular dynamics simulations. Herein, we combine these Langevin equations with surface hopping nonadiabatic dynamics methods to calculate the rate constants for thermal ET reactions in polar solvents for a wide range of electronic couplings and reaction free energies. Comparison of explicit and implicit solvent calculations illustrates that the mapping from explicit to implicit solvent models is valid even for solvents exhibiting complex relaxation behavior with multiple relaxation time scales and a short-time inertial response. The rate constants calculated for implicit solvent models with a single solvent relaxation time scale corresponding to water, acetonitrile, and methanol agree well with analytical theories in the Golden rule and solvent-controlled regimes, as well as in the intermediate regime. The implicit solvent models with two relaxation time scales are in qualitative agreement with the analytical theories but quantitatively overestimate the rate constants compared to these theories. Analysis of these simulations elucidates the importance of multiple relaxation time scales and the inertial component of the solvent response, as well as potential shortcomings of the analytical theories based on single time scale solvent relaxation models. This implicit solvent approach will enable the simulation of a wide range of ET reactions via the stochastic dynamics of a single collective solvent coordinate with parameters that are relevant to experimentally accessible systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Determination of Gas-Phase Ion Structures of Locally Polar Homopolymers Through High-Resolution Ion Mobility Spectrometry–Mass Spectrometry

The strong synergy arising from coupling two orthogonal analytical techniques such as ion mobility and mass spectrometry can be used to separate complex mixtures and determine structural information of analytes in the gas phase. A tandem study is performed using two systems with different gases and pressures to ascertain gas-phase conformations of homopolymer ions. Aside from spherical and stretched configurations, intermediate configurations formed by a multiply charged globule and a “bead-on-a-string” appendix are confirmed for polyethylene-glycol (PEG), polycaprolactone (PCL), and polydimethylsiloxane (PDMS). These intermediate configurations are shown to be ubiquitous for all charge states and masses present. For each charge state, configurations evolve in two distinctive patterns: an inverse evolution which occurs as an elementary charge attached to the polymer leaves the larger globule and incorporates itself into the appendage, and a forward evolution which reduces the globule without relinquishing a charge while leaving the appendix relatively constant. Forward evolutions are confirmed to form self-similar family shapes that transcend charge states for all polymers. Identical structural changes occur at the same mass over charge regardless of the system, gas or pressure strongly suggesting that conformations are only contingent on number of charges and chain length, and start arranging once the ion is at least partially ejected from the droplet, supporting a charge extrusion mechanism. Configurational changes are smoother for PDMS which is attributed to the larger steric hindrance caused by protruding pendant groups. This study has implications in the study of the configurational space of more complex homopolymers and heteropolymers. .

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2025

Tunable Stabilization of Cuprous Ions via Kinetic and Thermodynamic Control of Cu Electrodeposition in Non-Aqueous Media

In this work, significant stabilization of Cu + ions is achieved in non-aqueous electrolytes containing TFSI - and Cl - anions with diglyme as solvent. When Cl - is absent, stabilization of Cu + occurs due to the very low stability constant of Cu 2+ in diglyme. However, in the presence of relatively low Cl - concentrations (i.e., equimolar relative to Cu 2+ ), both Cu + and Cu 2+ form extremely stable Cu 2+ / + [Cl - ] complexes resulting in a similar to 1200 mV negative shift of the Cu + /0 redox couple relative to that of more easily reduced Cu + [TFSI - ][Cl - ] complexes. Furthermore, these results suggest that the lower solvation energies and wider electrochemical stability windows of non-aqueous solvents relative to water enable anions to play a much more significant role in guiding complexation behavior-providing new possibilities for (electro)chemical stabilization of reactive intermediates and highlighting the wealth of unexplored opportunities for electrolyte design in non-aqueous systems.

Anion Association↗
DOE OSTI2021

Copper-Catalyzed Oxidation of Hydrazones to Diazo Compounds Using Oxygen as the Terminal Oxidant

In this work, a mild method for accessing diazo compounds via aerobic oxidation of hydrazones is described. This catalytic transfor-mation employs a Cu(OAc) 2 /pyridine catalyst and molecular oxygen from ambient air as the terminal oxidant, generating water as the sole byproduct and affording the desired diazo compounds within minutes at room temperature. A broad array of electronically diverse aryldiazo esters, ketones and amides can be accessed. Pyridine dramatically enhances the rate of the reaction by solubilizing the copper catalyst and serving as Brønsted base in the turnover-limiting proton-coupled oxidation of hydrazone by copper(II). Insights gained from mechanistic studies led to expansion of the scope of this method to include diaryl hydrazones, delivering diaryl diazomethane derivatives, which cannot be accessed via established diazo transfer meth-ods. The products of this method may be employed in rhodium carbene catalysis without isolation of the diazo intermediate to afford cyclopropane products in good yield with high enantioselectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Clarifying the dehydrogenation pathway of catalysed Li4(NH2)3BH4-LiH composite

The effect of different metal oxides (Co3O4 and NiO) on the dehydrogenation reactions pathways of the Li4(NH2)3BH4-LiH composite was investigated. The additives were reduced to metallic species i.e. Co and Ni which act as catalysts by breaking the B-H bonds in the Li-B-N-H compounds. The onset desorption temperature was lowered 32 °C for the Ni-catalysed sample, which desorbed 8.8 wt% hydrogen below 275°C. It was demonstrated that the decomposition of the doped composite followed a mechanism via LiNH2 and Li3BN2 formation as the end product with a strong reduction of NH3 emission. The sample could be partially re-hydrogenated (~1.5 wt%) due to the lithium imide/amide transformation. To understand the LiH role, the Li4(NH2)3BH4-LiH-NiO and the Li4(NH2)3BH4-NiO composites were compared. The absence of LiH as a reactive forced the system to follow another path, which involved the formation of an intermediate phase of composition Li3BN2H2 at the early stages of dehydrogenation and the end desorption products LiNH2 and monoclinic Li3BN2. We showed evidence for the interaction between NiO and LiNH2 during heating and we propose that the presence of Li facilitates a NHx-rich environment and the Ni catalyst mediates the electron transfer to promote NHx coupling.

hydrogen storage materials, Lithium borohydride↗
DOE OSTI2015

Invariants in the Yukawa system's thermodynamic phase diagram

This paper shows that several known properties of the Yukawa system can be derived from the isomorph theory, which applies to any system that has strong correlations between its virial and potential-energy equilibrium fluctuations. Such “Roskilde-simple” systems have a simplified thermodynamic phase diagram deriving from the fact that they have curves (isomorphs) along which structure and dynamics in reduced units are invariant to a good approximation. We show that the Yukawa system has strong virial potential-energy correlations and identify its isomorphs by two different methods. One method, the so-called direct isomorph check, identifies isomorphs numerically from jumps of relatively small density changes (here 10%). The second method identifies isomorphs analytically from the pair potential. The curves obtained by the two methods are close to each other; these curves are confirmed to be isomorphs by demonstrating the invariance of the radial distribution function, the static structure factor, the mean-square displacement as a function of time, and the incoherent intermediate scattering function. Since the melting line is predicted to be an isomorph, the theory provides a derivation of a known approximate analytical expression for this line in the temperature-density phase diagram. The paper's results give the first demonstration that the isomorph theory can be applied to systems like dense colloidal suspensions and strongly coupled dusty plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Finite Element Modeling of Electrochemical Polishing of Niobium in Hydrofluoric-Sulfuric Acid Electrolyte

Niobium (Nb) used in superconducting radio-frequency cavities requires smooth surface to achieve optimal performance. In this work, a finite element model that coupled electrochemistry, heat transfer, and fluid dynamics was developed to investigate the electrochemical polishing mechanisms of Nb, using experimentally measured polarization results of coupon samples as validations. The current and potential distribution, oxide growth kinetics of Nb in a complex cavity geometry was investigated as a function of temperature and coolant flow. A low temperature coolant with intermediate flow rate was found to reduce surface current and ensure oxide uniformity. These results could shed light on the design of future particle accelerators.

SRF accelerator cavity↗
DOE OSTI2023

Biogeochemical Changes in Estuaries

The biogeochemical composition of materials suspended and dissolved in estuarine waters is substantially transformed by biological and abiotic processes as water from rivers and subterranean aquifers travels through estuaries to the coastal ocean, influencing the rate of storage and/or exchange of carbon with the atmosphere. Biogeochemical signatures in the upper reaches of estuaries (e.g., low salinity) generally reflect characteristics of the rivers and groundwater draining into the estuary. The composition of organic matter (OM) where rivers meet estuaries is a mixture of terrigenous signatures dependent on watershed landscape features, aquatic signatures dependent on the prominence of freshwater primary productivity, and intermediate metabolites (i.e., byproducts of in situ transformation) of these terrigenous and aquatic OM sources. The prominence of aquatic primary production-derived OM and products of microbial decomposition generally increases towards the lower reaches of estuaries where they meet the coastal ocean (i.e.., continental shelf). The nature of biogeochemical transformations occurring along estuarine gradients is closely coupled with factors that are poised to change under multiple compounding disturbances and stress factors related to both climate change and other anthropogenic global changes. This chapter describes the fundamental mechanisms that drive the transport, transformation, and storage of OM in estuaries and how these dynamics have and may continue to change in response to key disturbances and stressors related to climate change and other anthropogenic global changes including warming, intensifying hydrological extremes (e.g., droughts and floods), sea level rise, and acidification.

Ward, Nicholas D.↗
DOE OSTI2023

Future climate change in the Agulhas system and its associated impact on South African rainfall

South African climate variability has been linked to changes in both the Agulhas system and external forcing (i.e. CO 2 and ozone). We analysed future climate change in the Agulhas system volume transport and its associated impacts on South Africa’s precipitation using the Community Climate System Model version 4 as part of the Coupled Model Intercomparison Project, phase 5. Output from one historical and three future greenhouse gas emission scenarios were examined to project various climate storylines. We found that the Agulhas Current volume transport decreases across all three scenarios and that the current displays a strong baroclinic component with an increase in transport at the surface and decrease at intermediate depths. Agulhas leakage was found to increase with historical emissions. Additionally, an east-west dipole pattern for convective precipitation was found over South Africa, with an increase over the eastern region related to an increase in greenhouse gas emissions and a decrease in the western region linked to the location of Hadley cell edge latitude. Moving into the 21st century, future predictions in regional climate variability are shown to be dependent on the intensity of greenhouse gas emissions and are extremely important for South Africa, a region prone to drought and flooding and home to a large population dependent on rain-fed agriculture.Significance:Future climate variability in the Agulhas system and South African region is heavily dependent on changes in external forcing.The Agulhas Current volume transport decreases as the greenhouse gas emissions continue to increase and a strong baroclinic component is found with an increase in transport at the surface and a decrease at the intermediate depths.A strong east-west dipole precipitation pattern is found over South Africa with the increase in the eastern region related to the increase in greenhouse gas emissions and the decrease in the western region related to the location of the Hadley cell edge latitude.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Photoenzymatic Enantioselective Intermolecular Radical Hydroalkylation: Experimental Crystal Structure Determination

Enzymes are increasingly explored for use in asymmetric synthesis, but their applications are generally limited by the reactions available to naturally occurring enzymes. Recently, interest in photocatalysis has spurred the discovery of novel reactivity from known enzymes. However, so far photoinduced enzymatic catalysis has not been used for the cross-coupling of two molecules. For example, the intermolecular coupling of alkenes with α-halo carbonyl compounds through a visible-light-induced radical hydroalkylation, which could provide access to important γ-chiral carbonyl compounds, has not yet been achieved by enzymes. The major challenges are the inherent poor photoreactivity of enzymes and the difficulty in achieving stereochemical control of the remote prochiral radical intermediate. Here we report a visible-light-induced intermolecular radical hydroalkylation of terminal alkenes that does not occur naturally, catalysed by an ‘ene’ reductase using readily available α-halo carbonyl compounds as reactants. This method provides an efficient approach to the synthesis of various carbonyl compounds bearing a γ-stereocentre with excellent yields and enantioselectivities (up to 99 percent yield with 99 percent enantiomeric excess), which otherwise are difficult to access using chemocatalysis. Mechanistic studies suggest that the formation of the complex of the substrates (α-halo carbonyl compounds) and the ‘ene’ reductase triggers the enantioselective photoinduced radical reaction. Our work further expands the reactivity repertoire of biocatalytic, synthetically useful asymmetric transformations by the merger of photocatalysis and enzyme catalysis.

Huang, Xiaoqiang↗
NASA NTRS1985

Modelling of Laser-Enhanced Chemical Vapor Deposition

Research is directed at development of a detailed model of mass and heat transfer and chemical reaction in the pyrolysis of silane for the growth of thin amorphous silicon substrates incorporating laser heating of the gas phase above the film. The model will be the basis for evaluation of the relative importances of the decomposition of SiH4 in the vapor phase, mass transfer of the intermediate species, e.g., SiH2, and the evolution of hydrogen gas. Plans are also underway for developing a model for homogeneous nucleation of Si in the vapor phase to model the rate limitations observed at high gas-phase temperatures and high partial pressures of silane. Work was concentrated on an almost one-dimensional model for the coupling of the CO2 laser beam for heat transfer of the vapor phase with simple kinetic models for SiH4 decomposition and subsequent absorption of Si vapor on the substrate. Mass transfer in the vapor phase is assumed to be solely by diffusion. The role of convection in the vapor phase caused by the large changes in density in and around the center of the laser beam will be analyzed to evaluate the potential of microgravity experiments for increasing the uniformity of the film and the deposition rate.

Brown, R. A.↗
NASA NTRS2014

Characterization of MgB2 Superconducting Hot Electron Bolometers

Hot-Electron Bolometer (HEB) mixers have proven to be the best tool for high-resolution spectroscopy at the Terahertz frequencies. However, the current state of the art NbN mixers suffer from a small intermediate frequency (IF) bandwidth as well as a low operating temperature. MgB2 is a promising material for HEB mixer technology in view of its high critical temperature and fast thermal relaxation allowing for a large IF bandwidth. In this work, we have fabricated and characterized thin-film (approximately 15 nanometers) MgB2-based spiral antenna-coupled HEB mixers on SiC substrate. We achieved the IF bandwidth greater than 8 gigahertz at 25 degrees Kelvin and the device noise temperature less than 4000 degrees Kelvin at 9 degrees Kelvin using a 600 gigahertz source. Using temperature dependencies of the radiation power dissipated in the device we have identified the optical loss in the integrated microantenna responsible as a cause of the limited sensitivity of the current mixer devices. From the analysis of the current-voltage (IV) characteristics, we have derived the effective thermal conductance of the mixer device and estimated the required local oscillator power in an optimized device to be approximately 1 microwatts.

Superconducting Devices↗
NASA NTRS2025

PSE-Based Aerodynamic Flow Transition Prediction Using Automated Unstructured CFD Integration

Accurate, robust, and efficient prediction of transition in viscous flows is a significant challenge in computational fluid dynamics. We present a coupled, high-fidelity, iterative approach that leverages the FUN3D flow solver and the LASTRAC stability code to predict transition in low-disturbance environments, initiated by the linear growth of boundary-layer instability modes. Our method integrates the ability of FUN3D to compute mixed laminar-transitional-turbulent mean flows via transition-sensitized Reynolds-Averaged Navier-Stokes equations with the ability of LASTRAC to perform linear stability analysis, all within an automated framework that requires no intermediate user involvement. Unlike conventional frameworks that rely on classical stability theory or reduced-order metamodels, our approach employs the parabolized stability equations to provide more accurate and reliable estimates of disturbance growth for multiple instability mechanisms, including Tollmien-Schlichting, Kelvin-Helmholtz, and crossflow modes. By accounting for the effects of mean-flow nonparallelism as well as the surface curvature, this approach lays the foundation for improved N-factor correlations for transition onset prediction in a broad class of flows. We apply this method to three distinct flow configurations: 1) flow over a zero-pressure-gradient flat plate, 2) the NLF-0416 airfoil with both natural and separation-induced transitions, and 3) a 6:1 prolate spheroid, where transition is primarily driven by crossflow instability. For the two-dimensional cases, a formulated intermittency distribution is used to model the transition zone in between the laminar and fully turbulent flows. The results include comparisons with experimental measurements, similar numerical approaches, and transport-equations-based models, demonstrating good agreement in surface pressure coefficients, transition onset locations, and skin-friction coefficients for all three configurations. Besides contributing a couple of new insights into boundary-layer transition in these canonical cases, this study provides a powerful tool for transition modeling in both research and design applications in aerodynamics.

Transition Prediction↗