Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FRACTURE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Evaluation of high strength, high conductivity CuNiBe alloys for fusion energy applications

The unirradiated tensile properties for several different heats and thermomechanical treatment conditions of precipitation strengthened Hycon 3HPTM CuNiBe (Cu-2%Ni-0.35%Be in wt.%) have been measured over the temperature range of 20-500 C for longitudinal and long transverse orientations. The room temperature electrical conductivity has also been measured for several heats, and the precipitate microstructure was characterized using transmission electron microscopy. The CuNiBe alloys exhibit very good combination of strength and conductivity at room temperature, with yield strengths of 630-725 MPa and electrical conductivities of 65-72% International Annealed Copper Standard (IACS). The strength remained relatively high at all test temperatures, with yield strengths of 420-520 MPa at 500 C. However, low levels of ductility (<5% uniform elongation) were observed at test temperatures above 200-250 C, due to flow localization near grain boundaries (exacerbated by having only 10-20 grains across the gage thickness of the miniaturized sheet tensile specimens). Scanning electron microscopy observation of the fracture surfaces found a transition from ductile transgranular to ductile intergranular fracture with increasing test temperature. Fission neutron irradiation to a dose of ~0.7 displacements per atom (dpa) at temperatures between 100 and 240 C produced a slight increase in strength and a significant decrease in ductility. The measured tensile elongation increased with increasing irradiation temperature, with a uniform elongation of ~3.3% observed at 240 C. The electrical conductivity decreased slightly following irradiation, due to the presence of defect clusters and Ni, Zn, Co transmutation products. Considering also previously published fracture toughness data, this indicates that CuNiBe alloys have irradiated tensile and electrical properties comparable or superior to CuCrZr and oxide dispersion strengthened copper at temperatures <250 C, and may be an attractive candidate for certain fusion energy structural applications. Conversely, CuNiBe may not be preferred at intermediate temperatures of 250-500 C due to the poor ductility and fracture toughness of CuNiBe alloys at temperatures >250 C. The potential deformation mechanisms responsible for the transition from transgranular to intergranular fracture are discussed. The possible implications for other precipitation hardened alloys such as nickel based superalloys are briefly discussed.

Zinkle, Steven J↗

Development of Laser Powder Bed Fusion NASA HR-2 for Hydrogen Sensitive Liquid Rocket Engine Applications

The National Aeronautics and Space Administration (NASA) has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the late 2000’s. AM has provided new design and manufacturing opportunities to reduce cost and schedule, consolidate parts, and optimize performance. Laser Powder Bed Fusion (L-PBF) is one of the most commonly used AM processes to fabricate components that have complex shape and need fine feature resolution. Due to exposure to high pressure gaseous hydrogen, mechanical property degradation caused by hydrogen environment embrittlement (HEE) is a critical concern for many materials in liquid hydrogen propulsion systems. NASA has identified the need to develop and advance new materials in unique engine applications using liquid hydrogen as a propellant. One such material being developed at NASA Marshall Space Flight Center is L-PBF NASA HR-2 (Hydrogen Resistant-2), a high-strength Fe-Ni-based superalloy resistant to HEE. The chemistry of NASA HR-2 was formulated to meet requirements for key liquid rocket engine (LRE) components that operate in high-pressure hydrogen environments. Initial development and material characterization found NASA HR-2 has excellent L-PBF printability and its microstructure evolves well after heat treatment. This new alloy has undergone fundamental metallurgical evaluations, heat treatment studies, detailed microstructure characterization, and mechanical testing across a range of temperatures. Tensile testing was performed in pressurized gaseous hydrogen (GH2) environment to assess its resistance to HEE. L-PBF NASA HR-2 has an average yield stress of 95 ksi, ultimate tensile stress of 165 ksi, and very high fracture elongation at 34 - 36% when tested in a 5 ksi high pressure hydrogen environment. The tensile property data confirms hydrogen has little influence on its ductility, strength, and fracture behavior. L-PBF NASA HR-2 is a promising option for many hydrogen sensitive LRE components that require exceptional resistance to HEE. The development of L-PBF NASA HR-2 is funded under the grants provided by Jacobs TIPI program and the Liquid Engine Office at NASA Marshall Space Flight Center. This paper will provide an overview of the L-PBF process development, material characterization, mechanical and thermophysical properties, and LRE hardware development for NASA HR-2.

NASA HR-2↗

Development of Laser Powder Bed Fusion NASA HR-2 for Hydrogen Sensitive Liquid Rocket Engine Applications

The National Aeronautics and Space Administration (NASA) has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the late 2000’s. AM has provided new design and manufacturing opportunities to reduce cost and schedule, consolidate parts, and optimize performance. Laser Powder Bed Fusion (L-PBF) is one of the most commonly used AM processes to fabricate components that have complex shape and need fine feature resolution. Due to exposure to high pressure gaseous hydrogen, mechanical property degradation caused by hydrogen environment embrittlement (HEE) is a critical concern for many materials in liquid hydrogen propulsion systems. NASA has identified the need to develop and advance new materials in unique engine applications using liquid hydrogen as a propellant. One such material being developed at NASA Marshall Space Flight Center is L-PBF NASA HR-2 (Hydrogen Resistant-2), a high-strength Fe-Ni-based superalloy resistant to HEE. The chemistry of NASA HR-2 was formulated to meet requirements for key liquid rocket engine (LRE) components that operate in high-pressure hydrogen environments. Initial development and material characterization found NASA HR-2 has excellent L-PBF printability and its microstructure evolves well after heat treatment. This new alloy has undergone fundamental metallurgical evaluations, heat treatment studies, detailed microstructure characterization, and mechanical testing across a range of temperatures. Tensile testing was performed in pressurized gaseous hydrogen (GH2) environment to assess its resistance to HEE. L-PBF NASA HR-2 has an average yield stress of 95 ksi, ultimate tensile stress of 165 ksi, and very high fracture elongation at 34 - 36% when tested in a 5 ksi high pressure hydrogen environment. The tensile property data confirms hydrogen has little influence on its ductility, strength, and fracture behavior. L-PBF NASA HR-2 is a promising option for many hydrogen sensitive LRE components that require exceptional resistance to HEE. The development of L-PBF NASA HR-2 is funded under the grants provided by Jacobs TIPI program and the Liquid Engine Office at NASA Marshall Space Flight Center. This paper will provide an overview of the L-PBF process development, material characterization, mechanical and thermophysical properties, and LRE hardware development for NASA HR-2.

NASA HR-2↗

Wear resistance and microstructural properties of Ni–Al/h-BN/WC–Co coatings deposited using plasma spraying

Hexagonal boron nitride (h-BN) and tungsten carbide cobalt (WC–Co) were added to nickel aluminum alloy (Ni–Al) and deposited as plasma sprayed coatings to improve their tribological properties. The microstructure of the coatings was analyzed using a scanning electron microscope (SEM). Following wear test, the worn surface morphologies of the coatings were analyzed using a SEM to identify their fracture modes. The results of this study demonstrate that the addition of h-BN and WC–Co improved the properties of the coatings. Ni–Al/h-BN/WC–Co coatings with high hardness and favorable lubrication properties were deposited. - Highlights: • We mixed Ni–Al, h-BN and WC–Co powders and deposited them as composite coatings. • Adding WC–Co was found to increase the hardness and reduce the wear volume loss. • Adding h-BN was found to decrease the hardness and reduce the friction coefficient. • This composite coating was shown to have improved wear properties at 850 °C.

36 MATERIALS SCIENCE↗

High temperature fracture toughness of single-layer CrAlN and CrAlSiN hard coatings

Hardness and toughness are among of the most important physical properties of hard coatings and it is important to analyze them at temperatures present during coating applications. CrAlN and CrAlSiN are hard coating materials frequently used in high temperature applications. Here, while both possess high oxidation resistance and thermal stability, they differ in their microstructure. In this work, the fracture toughness of magnetron-sputtered single-layer CrAlN and CrAlSiN hard coatings was determined up to 700 °C by in-situ scanning electron microscopy micro-cantilever deflection tests. The results show a decreasing trend of the fracture toughness with increasing temperature. While both coatings' fracture toughness trends are similar up to 400 °C, they diverge at higher temperatures. In general, the evolution of the fracture toughness with increasing temperature shows similarities to the observed changes in hardness in the same temperature range.

36 MATERIALS SCIENCE↗

Investigation of dynamic fracture behavior of additively manufactured Al-10Si-Mg using high-speed synchrotron X-ray imaging

The dynamic tensile properties of additively manufactured (AM) and cast Al-10Si-Mg alloy were disccused using high-speed synchrotron X-ray imaging coupled with a modified Kolsky bar apparatus. A controlled tensile loading (strain rate &approx; 750 s -1 ) was applied using the Kolsky bar apparatus and the deformation and fracture behavior were recorded using the high-speed X-ray imaging setup. The CT and high-speed imaging results worked together to identify the location of the critical flaw and to capture the dynamics of crack propagation. In all experiments, the critical flaw was located on the surface of each specimen. The AM specimens displayed significantly higher crack propagation speed, yield strength, ultimate tensile strength, strain hardening coefficient, and yet lower ductility compared to the cast specimens under dynamic tension. Although the strength values were higher for the AM specimens, the critical mode I stress intensity factors were comparable for both specimens. The microstructures of the samples were characterized by synchrotron X-ray computed tomography (CT) and scanning electron microcopy. The correlation between the dynamic fracture behavior of the samples and the microstructure of the samples is analyzed and discussed.

36 MATERIALS SCIENCE↗

Surface modification of bamboo fiber with sodium hydroxide and graphene oxide in epoxy composites

Bamboo fibers (BFs) have high mechanical properties and are candidate reinforcement for epoxy matrix composites. However, to improve performance, good fiber-matrix interaction is required. In this work, unidirectional long BF reinforced epoxy composites at fiber volume content of 22%, 40%, and 50% were made by compression molding. The 40 v% untreated BF reinforced composites exhibited 107% and 439% increase for flexural strength and modulus, respectively, compared to neat epoxy. Sodium hydroxide (NaOH) treatment was used to modify the surface of the BFs, and then the NaOH modified BFs were coated with graphene oxide (GO). The 40 v% NaOH modified BF composites showed an improvement from 259.9 to 327.5 MPa for flexural strength and from 16.7 to 21.5 GPa for flexural modulus, compared to 40 v% untreated BF composites. Slight improvement in properties up to 334.6 MPa for flexural strength and up to 23.8 GPa for flexural modulus was achieved for composites made of 40 v% NaOH/GO modified BF. Surface modification of BF after the NaOH and NaOH/GO treatment was confirmed by X-ray photoelectron spectroscopy and by scanning electron microscopy, which showed differences on the fiber surface morphology and on the composite fracture surface. This BF surface modification approach with GO has potential to impart other properties beyond mechanical to produce multifunctional composite and lead to the use of sustainable plant fibers as alternatives to synthetic fibers.

36 MATERIALS SCIENCE↗

Computational modeling of coupled mechanical damage and electrochemistry in ternary oxide composite electrodes

Performance degradation of ternary layered oxide cathodes largely originates from their loss of structural integrity in cyclic usage. Mechanical damage, such as intergranular fracture of the active particles, is not only a mechanical cleavage process but also interferes with electrochemical kinetics such as infiltration of liquid electrolyte, surface corrosion of the constituent primary particles, and may eventually isolate the primary grains from the electron conducting network. Here, in this work, we develop a computational framework that integrates electrochemistry of a LiNi x Mn y Co 1−x−y O 2 (NMC) composite cathode with mechanical damage of the active particles. To fully examine the intricate chemomechanical behavior of the electrode, we evaluate the effects of the anisotropic material properties, the influence of mechanical potential on Li transport, and the concurrent intergranular fracture and electrolyte penetration along the grain boundaries upon multiple cycles. Electrolyte infiltration benefits capacity retention but aggravates further mechanical damage by corrosion. Structural failure mostly occurs in the first charging due to the anisotropic mechanical strain between the primary grains, while the resulting damage remains stable in the later few cycles. The results are consistent with experimental observations and the integration of electrochemistry and mechanical failure enables a step further understanding of the complex mechanism of battery degradation.

Battery degradation↗

AERoBOND Project Summary

Under NASA’s Convergent Aeronautics Solutions (CAS) project, the Adhesive-Free Bonding of Complex Composites (AERoBOND) project investigated off-stoichiometric epoxy polymers for fast, reliable assembly of epoxy matrix composite structures. The project goal was to demonstrate feasibility of the AERoBOND joining method by demonstrating mechanical properties greater than 80% of conventional co-cured materials while reducing structure weight by 1%. The project consisted of three convergent research areas: material and process development, systems analysis, and material and process modeling. Material and process development was the largest component of AERoBOND with approximately 6 FTE and 1WYE of support to formulate and characterize new resins, prepare carbon fiber prepregs, fabricate laminates, measure mechanical properties, analyze failure results, and select material and process improvements. The systems analysis activity estimated the potential reduction in part count and aircraft weight by comparing models of composite wing boxes with no fasteners (co-cured structure), fasteners in major joints (co-cured stringers), and fasteners in all joints. The materials and process modeling activity included a molecular model of the AERoBOND materials system to predict mechanical properties of resins with offset stoichiometry and a process model to predict the effect of resin formulation and processing conditions on the extent of mixing and degree of cure in a finished joint. As the number of airline passenger trips doubles in the next 20 years (IATA/Tourism Economics Air Passenger Forecasts, April 2019), the increased demand for new commercial aircraft is now the single greatest technical challenge to the airframe manufacturing industry. To meet efficiency requirements, new aircraft must be fabricated primarily from high performance structural composites, but manufacturing processes are inherently slow with the largest bottleneck attributed to assembly and installation of fasteners (NASA/TM–2019-220428). Manufactures of commercial transport aircraft are compelled to install more than 100,000 redundant fasteners into bonded joints to prevent failures due to unpredictable weak bonds. In structural adhesive bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination, which can cause weak bonds. Currently, bond strength assessment is only possible through destructive testing (i.e., breaking the joint). For these reasons, regulatory organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to alleviate concerns with bond performance. The AERoBOND process enables reflow of matrix resin during assembly to eliminate the material discontinuity at the interface, thereby eliminating the dependence of mechanical performance on interfacial adhesion. The AERoBOND joint is equivalent to the interlaminar region obtained during a co-cure process, so joint performance depends on the cohesive properties of the matrix resin. Conventional co-cured structures, although too costly and complex for large-scale manufacturing, are trusted by manufacturers and regulators, and are certified for flight with few or no redundant fasteners.Systems analysis performed on a composite wing model at the scale of a single-aisle commercial transport aircraft indicated that >20,000 redundant fasteners per wing could be eliminated by implementing the AERoBOND joining method. A total weight reduction of 15% was predicted in a wing box by eliminating fasteners and thinning components that must no longer support localized fastener loads and accommodate fastener dimensions. Interlaminar shear fracture toughness measured by the end-notched flexure test was greater than 1 kJ/m2 (nearly 140% of the co-cured benchmark property), which is greatly in excess of the project goals for mechanical properties. Testing was planned to measure interlaminar tensile fracture toughness as well as interlaminar tensile and shear strengths using the same AERoBOND configuration, but was delayed due to closure of LaRC facilities during the COVID-19 pandemic. The AERoBOND process model is partially validated and available for experimental use. It allows the user to input AERoBOND process parameters such as material composition, laminate configuration, and cure cycle to predict the final cure state of the AERoBOND joint. A preliminary, multi-scale material model was developed to predict AERoBOND joint mechanical properties (stiffness and strength) based on the cure state of the joint provided by the process model. The timing for transition of this technology within NASA is excellent as NASA initiates new enduring projects to address composites manufacturing rate challenges. AERoBOND technology is well suited to AAVP/AATT objectives for rapid manufacturing of a composite wing. A minimal effort (1 FTE/$15k procurement/0 WYE) is proposed in FY21 to continue a minor mechanical testing effort and maintain a SAA with ASX composites to develop commercial quality prepreg material. An RFI with the composites industry is suggested to quantify the technology gap between the current TRL and the TRL needed for transition to industry. A moderate effort [3-4 FTE/$150k/1 WYE (~$115k)] is proposed in FY22 for the “high rate composites manufacturing” project currently in planning. The partnership with ASX Composites will be expanded to produce material for sub-element/element-scale “panel-off” activities. Industry partnerships with airframe manufacturers is an expected component to explore damage tolerance and environmental stability. Further development of multi-scale modeling tools (process model, meso-scale model, and molecular model) is planned to enhance and deliver tools for rapid manufacturing infusion.

Frank Louis Palmieri↗

FY17 CAES LDRD Annual Report

Metallic alloys are widely used or planned for use as structural and cladding materials in current and future reactors. Under irradiation, grain boundary (GB) cohesion strength decreases due to interaction with defects and impurities, leading to intergranular fracture and embrittlement of alloys. The objective of this project is to develop a technique for quantifying GB cohesion and its impact on fracture behavior in irradiated alloys, by utilizing transmission electron microscopic (TEM) in situ cantilever testing in concert with multi-scale modeling. The TEM in situ cantilever testing is a novel approach for studying the real-time mechanical response of materials. It will be used in this work for studying intergranular fracture behavior in several irradiated iron-based ferritic alloys and providing key information to link atomistic level events with mesoscale/macroscopic mechanical properties. The Multi-Physics Object-Oriented Simulation Environment (MOOSE)-based cohesive zone model (CZM) and extended finite element method (XFEM) for intergranular fracture of irradiated ferritic alloys will be developed in this work by utilizing atomistic results as inputs and experimental results for validation.

36 MATERIALS SCIENCE↗

Molecular dynamics simulations of intergranular fracture in UO2 with nine empirical interatomic potentials

The intergranular fracture behavior of UO2 was studied using molecular dynamics simulations with a bicrystal model. The anisotropic fracture behavior due to the different grain boundary characters was investigated with the View the MathML source symmetrical tilt S5 and the View the MathML source symmetrical tilt S3 ({1 1 1} twin) grain boundaries. Nine interatomic potentials, seven rigid-ion plus two core–shell ones, were utilized to elucidate possible potential dependence. Initiating from a notch, crack propagation along grain boundaries was observed for most potentials. The S3 boundary was found to be more prone to fracture than the S5 one, indicated by a lower energy release rate associated with the former. However, some potential dependence was identified on the existence of transient plastic deformation at crack tips, and the results were discussed regarding the relevant material properties including the excess energies of metastable phases and the critical energy release rate for intergranular fracture. In general, local plasticity at crack tips was observed in fracture simulations with potentials that predict low excess energies for metastable phases and high critical energy release rates for intergranular fracture.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FRACTURE RESISTANCE OF CAST AUSTENITIC STAINLESS STEELS

Cast austenitic stainless steels (CASS) possess excellent corrosion resistance and mechanical properties and are used alongside with wrought stainless steels (SS) in light water reactors for primary pressure boundaries and reactor core internal components. In contrast to an austenitic microstructure of wrought SS, CASS alloys consist of a dual-phase microstructure of delta ferrite and austenite. While the delta ferrite is critical for the service performance of CASS alloys, it is also vulnerable to embrittlement when exposed to reactor service temperatures and fast neutron irradiations. In this study, the combined effect of thermal aging and neutron irradiation on the degradation of CASS alloys was investigated. Static casts of CF-3 and CF-8 grades with > 23% delta ferrite were selected for the study, and specimens with and without prior thermal aging were irradiated at ~320°C to about 0.08 dpa. Crack growth rate and fracture toughness J-integral resistance curve tests were performed in simulated light water reactor environments with low corrosion potential. While no elevated crack propagation rates were detected, significant reductions in fracture toughness were observed after either thermal aging or neutron irradiation. The loss of fracture toughness due to neutron irradiation seemed more evident in the samples without prior thermal aging. Transmission electron microscope (TEM) examination showed that both neutron irradiation and thermal aging affect the microstructural evolution of delta ferrite. A high density of G-phase precipitates was observed in both thermally aged and irradiated specimens The evolution of the precipitate microstructure is more extensive in the samples subjected to both thermal aging and neutron irradiation. The similarity of precipitate microstructures resulting from thermal aging and neutron irradiation are consistent with the fracture toughness results, suggesting a common microstructural origin of the observed embrittlement among the tested specimens.

cast austenitic stainless steels↗

Mechanical measurements on lithium phosphorous oxynitride coated silicon thin film electrodes for lithium-ion batteries during lithiation and delithiation

The development of large stresses during lithiation and delithiation drives mechanical and chemical degradation processes (cracking and electrolyte decomposition) in thin film silicon anodes that complicate the study of normal electrochemical and mechanical processes. To reduce these effects, lithium phosphorous oxynitride (LiPON) coatings were applied to silicon thin film electrodes. Applying a LiPON coating has two purposes. First, the coating acts as a stable artificial solid electrolyte interphase. Second, it limits mechanical degradation by retaining the electrode's planar morphology during cycling. The development of stress in LiPON-coated electrodes was monitored using substrate curvature measurements. LiPON-coated electrodes displayed highly reproducible cycle-to-cycle behavior, unlike uncoated electrodes which had poorer coulombic efficiency and exhibited a continual loss in stress magnitude with continued cycling due to film fracture. The improved mechanical stability of the coated silicon electrodes allowed for a better investigation of rate effects and variations of mechanical properties during electrochemical cycling.

36 MATERIALS SCIENCE↗

Effect of vanadium oxide addition on thermomechanical behaviors of borosilicate glasses: Toward development of high crack resistant glasses for nuclear waste disposal

The effect of of V2O5 additions (up to 8 mol%) on the physical properties (e.g., density, glass transition temperature and refractive indices) and mechanical behaviors (e.g., hardness, fracture toughness, elastic modulus) of a soda-lime borosilicate glass with a composition of 60.2SiO(2)-16.0B(2)O(3)-12.6Na(2)O-3.8Al(2)O(3)-5.7CaO-1.7ZrO(2) (mol%) have been investigated systematically. It was found that introducing V2O5 decreases the glass transition temperature and hardness while increases the refractive index and crack initiation load. Composition-property relationships, especially on mechanical properties, were examined in order to provide insights for the development of new glass materials with outstanding mechanical properties. The results show that V2O5 can be a glass component for engineering and insuring high crack resistant glasses and glasses with long-term stability. Additionally, elastic properties as a function of temperature were studied using Brillouin light scattering and temperature-independent elastic moduli behaviors were observed.

Lu, Xiaonan↗

Continuous-Discontinuous Model for Ductile Fracture

In this contribution, a continuum-dicontinuum model for ductile failure is presented. The degradation of material properties trough deformation is described by Continuum Damage Mechanics in a non-local integral formulation to avoid mesh dependence. In the final stage of failure, the damaged zone is replaced by a cohesive macro crack and subsequent traction-free macro crack for a more realistic representation of the phenomenon. The inclusion of the discontinuity surfaces is performed by the XFEM and Level Set Method and avoids the spurious damage growth typical of this class of models.

36 MATERIALS SCIENCE↗

Mechanical Properties of Plasma-Sprayed ZrO2-8 wt% Y2O3 Thermal Barrier Coatings

Mechanical behavior of free standing, plasma-sprayed ZrO2-8 wt% Y2O3 thermal barrier coatings, including strength, fracture toughness, fatigue, constitutive relation, elastic modulus, and directionality, has been determined under various loading-specimen configurations. This report presents and describes a summary of mechanical properties of the plasma-sprayed coating material to provide them as a design database.

Choi, Sung R.↗

CoCrMo cellular structures made by Electron Beam Melting studied by local tomography and finite element modelling

The work focuses on the structural and mechanical characterization of Co-Cr-Mo cellular samples with cubic pore structure made by Electron Beam Melting (EBM). X-ray tomography was used to characterize the architecture of the sample. High resolution images were also obtained thanks to local tomography in which the specimen is placed close to the X-ray source. These images enabled to observe some defects due to the fabrication process: small pores in the solid phase, partially melted particles attached to the surface. Then, in situ compression tests were performed in the tomograph. The images of the deformed sample show a progressive buckling of the vertical struts leading to final fracture. The deformation initiated where the defects were present in the strut i.e. in regions with reduced local thickness. The finite element modelling confirmed the high stress concentrations of these weak points leading to the fracture of the sample. - Highlights: • CoCrMo samples fabricated by Electron Beam Melting (EBM) process are considered. • X-ray Computed Tomography is used to observe the structure of the sample. • The mechanical properties are tested thanks to an in situ test in the tomograph. • A finite element model is developed to model the mechanical behaviour.

36 MATERIALS SCIENCE↗

Micromechanics, Fracture Mechanics and Gas Permeability of Composite Laminates for Cryogenic Storage Systems

A micromechanics method is developed to investigate microcrack propagation in a liquid hydrogen composite tank at cryogenic temperature. The unit cell is modeled using square and hexagonal shapes depends on fiber and matrix layout from microscopic images of composite laminates. Periodic boundary conditions are applied to the unit cell. The temperature dependent properties are taken into account in the analysis. The laminate properties estimated by the micromechanics method are compared with empirical solutions using constituent properties. The micro stresses in the fiber and matrix phases based on boundary conditions in laminate level are calculated to predict the formation of microcracks in the matrix. The method is applied to an actual liquid hydrogen storage system. The analysis predicts micro stresses in the matrix phase are large enough to cause microcracks in the composite. Stress singularity of a transverse crack normal to a ply-interface is investigated to predict the fracture behavior at cryogenic conditions using analytical and finite element analysis. When a transverse crack touches a ply-interface of a composite layer with same fiber orientation, the stress singularity is equal to 1/2. When the transverse crack propagates to a stiffer layer normal to the ply-direction, the singularity becomes less than 1/2 and vice versa. Finite element analysis is performed to predict the fracture toughness of a laminated beam subjected to fracture loads measured by four-point bending tests at room and cryogenic temperatures. As results, the fracture load at cryogenic temperature is significantly lower than that at room temperature. However, when thermal stresses are taken into consideration, for both cases of room and cryogenic temperatures, the difference of the fracture toughness becomes insignificant. The result indicates fracture toughness is a characteristic property, which is independent to temperature changes. The experimental analysis is performed to investigate the effect of cryogenic cycling on permeability for various composite material systems. Textile composites have lower permeability than laminated composites even with increasing number of cryogenic cycle. Nano-particles dispersed in laminated composites do not show improvement on permeability. The optical inspection is performed to investigate the microcrack propagation and void content in laminated composites and compared the microscopic results before and after cryogenic cycling.

Choi, Sukjoo↗