Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DOPPLER EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

The structure of a separating turbulent boundary layer. IV - Effects of periodic free-stream unsteadiness

Measurements were obtained of the sinusoidal unsteadiness of the free stream velocity during the separation of the turbulent boundary layer. Data were gathered by single wire and cross-wire, anemometry upstream of flow detachment, by laser Doppler velocimetry to detect the movement of the flow in small increments, and by a laser anemometer in the detached zone to measure turbulence and velocities. The study was restricted to a sinusoidal instability frequency of 0.61 and a ratio of oscillation amplitude to mean velocity of 0.3. Large amplitude and phase variations were found after the detachment, with unsteady effects producing hysteresis in the relationships between flow parameters. The detached shear layer decreased in thickness with increasing free-stream velocity and increases in the Reynolds shear stress. Deceleration of the free stream velocity caused thickening in the shear layer and upstream movement of the flow reversal location. The results are useful for studies of compressor blade and helicopter rotors in transition.

Simpson, R. L.↗

The motional Stark effect diagnostic on NSTX

This work describes the implementation and recent results from the motional Stark effect (MSE) collisionally induced fluorescence diagnostic on NSTX. Due to the low magnetic field on NSTX the MSE diagnostic requires a new approach for the viewing optics and spectral filter. This has been accomplished with a novel optical design that reduces the geometric Doppler broadening, and a high throughput, high resolution spectral filter to optimize signal-to-noise ratio. With these improvements the polarization fraction is {approx}30%-40% and, combined with the large throughput, a time resolution of {approx}5 ms. The MSE diagnostic presently has 16 sight lines operating, providing measurements of the magnetic field line pitch from the plasma center to near the outboard edge of the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Stationary light in cold-atomic gases

We discuss stationary light created by a pair of counterpropagating control fields in {lambda}-type atomic gases with electromagnetically induced transparency for the case of negligible Doppler broadening. In this case, the secular approximation used in the discussion of stationary light in hot vapors is no longer valid. We discuss the quality of the effective light-trapping system and show that in contrast to previous claims it is finite even for vanishing ground-state dephasing. The dynamics of the photon loss is in general nonexponential and can be faster or slower than in hot gases.

74 ATOMIC AND MOLECULAR PHYSICS↗

EFFECTS OF THE NON-RADIAL MAGNETIC FIELD ON MEASURING MAGNETIC HELICITY TRANSPORT ACROSS THE SOLAR PHOTOSPHERE

It is generally believed that the evolution of magnetic helicity has a close relationship with solar activity. Before the launch of the Solar Dynamics Observatory (SDO), earlier studies had mostly used Michelson Doppler Imager/SOHO line of sight (LOS) magnetograms and assumed that magnetic fields are radial when calculating the magnetic helicity injection rate from photospheric magnetograms. However, this assumption is not necessarily true. Here we use the vector magnetograms and LOS magnetograms, both taken by the Helioseismic and Magnetic Imager on SDO, to estimate the effects of the non-radial magnetic field on measuring the magnetic helicity injection rate. We find that: (1) the effect of the non-radial magnetic field on estimating tangential velocity is relatively small; (2) when estimating the magnetic helicity injection rate, the effect of the non-radial magnetic field is strong when active regions are observed near the limb and is relatively weak when active regions are close to disk center; and (3) the effect of the non-radial magnetic field becomes minor if the amount of accumulated magnetic helicity is the only concern.

79 ASTRONOMY AND ASTROPHYSICS↗

Influence of the line-shape model on the spectroscopic determination of the Boltzmann constant

Recent high-resolution spectroscopic experiments demonstrated the possibility of measuring the Boltzmann constant directly from the Doppler width of atomic or molecular lines; however, both experimental setups and data analysis methods still need to be improved to compete with the best acoustic methods. In this paper, the influence of choice of spectral line-shape model for data analysis on systematical error of the Doppler-width determination is analyzed on the example of the oxygen line near {lambda}=687 nm. Profile simulations were performed for many different models at pressures ranging from 0.012 Pa to 120 kPa, taking into account such line-shape effects as the speed dependence of collisional broadening and Dicke narrowing. We discuss limitations of an applicability of the Voigt profile for purposes of the Boltzmann constant determination. The influence of the model line-shape profile and the gas pressure range on the Doppler width extrapolated to the zero-pressure value is investigated.

74 ATOMIC AND MOLECULAR PHYSICS↗

HST/COS detection of the spectrum of the subdwarf companion of KOI-81

KOI-81 is a totally eclipsing binary discovered by the Kepler mission that consists of a rapidly rotating B-type star and a small, hot companion. The system was forged through large-scale mass transfer that stripped the mass donor of its envelope and spun up the mass gainer star. We present an analysis of UV spectra of KOI-81 that were obtained with the Cosmic Origins Spectrograph on the Hubble Space Telescope that reveal for the first time the spectral features of the faint, hot companion. We present a double-lined spectroscopic orbit for the system that yields mass estimates of 2.92 M{sub ⊙} and 0.19 M{sub ⊙} for the B-star and hot subdwarf, respectively. We used a Doppler tomography algorithm to reconstruct the UV spectra of the components, and a comparison of the reconstructed and model spectra yields effective temperatures of 12 and 19–27 kK for the B-star and hot companion, respectively. The B-star is pulsating, and we identified a number of peaks in the Fourier transform of the light curve, including one that may indicate an equatorial rotation period of 11.5 hr. The B-star has an equatorial velocity that is 74% of the critical velocity where centrifugal and gravitational accelerations balance at the equator, and we fit the transit light curve by calculating a rotationally distorted model for the photosphere of the B-star.

79 ASTRONOMY AND ASTROPHYSICS↗

Ionization effects due to solar flare on terrestrial ionosphere

Sudden frequency deviation ionospheric disturbances related to the flares of May 18 and 19, 1973 were observed from the NASA/MSFC high frequency Doppler sounder array system in Huntsville, Alabama. The results are compared with those observed at Table Mountain near Boulder, Colorado and at the University of Hawaii.

Wu, S. T.↗

First results of a study on turbulent boundary layers in oscillating flow with a mean adverse pressure gradient

The development of a turbulent unsteady boundary layer with a mean pressure gradient strong enough to induce separation, in order to complete the extend results obtained for the flat plate configuration is presented. The longitudinal component of the velocity is measured using constant temperature hot wire anemometer. The region where negative velocities exist is investigated with a laser Doppler velocimeter system with BRAGG cells. The boundary layer responds by forced pulsation to the perturbation of potential flow. The unsteady effects observed are very important. The average location of the zero skin friction point moves periodically at the perturbation frequency. Average velocity profiles from different instants in the cycle are compared. The existence of a logarithmic region enables a simple calculation of the maximum phase shift of the velocity in the boundary layer. An attempt of calculation by an integral method of boundary layer development is presented, up to the point where reverse flow starts appearing.

Houdeville, R.↗

Saturn gravity results obtained from Pioneer 11 tracking data and earth-based Saturn satellite data

Improved gravity coefficients for Saturn, its satellites and rings are calculated on the basis of a combination of Pioneer 11 spacecraft Doppler tracking data and earth-based determinations of Saturn natural satellite apse and node rates. Solutions are first obtained separately from the coherent Doppler tracking data obtained for the interval from August 20 to September 4, surrounding the time of closest approach, with the effects of solar plasma on radio signal propagation taken into account, and from secular rates for Mimas, Enceladus, Tethys, Dione, Rhea and Titan determined from astrometric data by Kozai (1957, 1976) and Garcia (1972). Combination of the data by the use of the Pioneer solution and corresponding unadjusted covariance matrix as a priori information for a secular rate analysis results in values for the total ring mass of essentially zero at a standard error level of 1.7 x 10 to the -6th Saturn masses, a ratio of solar mass to that of the Saturn system of 3498.09 + or - 0.22, masses of Rhea, Titan and Iapetus of 4.0 + or - 0.9, 238.8 + or - 3, and 3.4 + or - 1.3 x 10 to the -6th Saturn masses, respectively, and second and fourth zonal harmonics of 16,479 + or - 18 and -937 + or - 38, respectively. The harmonic coefficients are noted to be important as boundary conditions in the modeling of the Saturn interior.

Null, G. W.↗

IUE spectra of the hot close binary V Puppis

Low- and high-dispersion ultraviolet spectra obtained by the IUE of the early B-type close binary V Puppis are reported. The continuum derived from the low-dispersion images is consistent with a solar abundance model of effective temperature 25,000 K and log surface gravity 4.0. The high-dispersion spectra show shallow double lines, representing Doppler-resolved stellar lines, which are broadened as expected for the fast rotational velocities given by Levato (1974). The equivalent widths of the silicon lines, however, do not agree with the temperature derived for the star, while the silicon and carbon absorptions indicate a disordered photosphere in the presence of circumstellar gas. Several interstellar lines are also observed for the first time.

Koch, R. H.↗

Performance evaluation of the JPL interim digital SAR processor

The performance of the Interim Digital SAR Processor (IDP) was evaluated. The IDP processor was originally developed for experimental processing of digital SEASAT SAR data. One phase of the system upgrade which features parallel processing in three peripheral array processors, automated estimation for Doppler parameters, and unsupervised image pixel location determination and registration was executed. The method to compensate for the target range curvature effect was improved. A four point interpolation scheme is implemented to replace the nearest neighbor scheme used in the original IDP. The processor still maintains its fast throughput speed. The current performance and capability of the processing modes now available on the IDP system are updated.

Wu, C.↗

Emission line region kinematics in selected Seyfert galaxies

The kinematic state of the emission line regions of active galactic nuclei (AGN) is a fundamental problem which addresses the very nature of these objects. The currently popular model of the energy source of the latter is accretion onto the supermassive black hole which is believed to reside in the nuclear regions of galaxies. If this picture is correct then the emission line gas may be expected to be infalling, and may eventually provide the fuel to power them. It is very difficult to determine the kinematic state of the emission line gas because of the technical problems associated with their small apparent sizes, as seen from the earth. One can only observe the net emission from a large ensemble of clouds, so the emission lines are by necessity composite. Several very long exposures of NGC 1068, one of the very nearest Seyfert galaxies, were obtained. Because of its proximity, it is expected to have the best resolved emission line regions as seen from earth. The La emission line of neutral hydrogen will radiate preferentially in the direction of the central object because of the effects of emission line gas opacity on the transfer of radiation out of the clouds. By obtaining high dispersion observations of Doppler broadening of the line through the small entrance aperture of the IUE one can determine whether this material is in a state of outflow (expected if explosions power the central engine), inflow (expected for accretion onto a massive black hole), or rotation (expected for gas with significant angular momentum near the central regions of a galaxy).

Ferland, G. J.↗

Comparison of FFP predictions with measurements of a low-frequency signal propagated in the atmosphere

An experimental study of low-frequency propagation over a distance of 770 m was previously reported (J. Acoust. Soc. Am. Suppl. 1 86, S120 (1989)). For that study, sound speed profiles were reconstructed entirely from surface-layer micrometeorological data. When the acoustic data were compared with theoretical predictions from a fast field program (FFP), it was found that the FFP underpredicted sound levels measured in a shadow zone. Here, the effect on the predictions of including meteorological data for heights greater than the surface layer, i.e., wind profiles measured by a Doppler sodar, is discussed. Vertical structure of turbulence is simulated by stochastically perturbing the mean profiles, and the agreement between the acoustic data and FFP predictions is improved.

Wilson, K. Keith↗

Adaptive optics in coherent lidar wind measurements: A feasibility study

Laser Doppler radar (lidar) is widely used for remote sensing of wind velocities. Usable wavelengths for the laser are limited by the effects of atmospheric turbulence. An adaptive optical system is proposed to compensate for turbulence effects on signal power. The feasibility of an adaptive system is considered in light of the effects of speckle from the aerosol target. It is concluded that adaptive optics is a promising technique for improving the performance of a 2 micron lidar wind measurement system. The chief technical challenges are a laser that will give the required output and pulse repetition rate, a combined Hartmann sensor and heterodyne detector, and a suitable reconstruction algorithm.

Leland, Robert P.↗

High-resolution OH LIF velocity measurement technique for high-speed reacting flows

A nonintrusive optical technique was developed for the quantitative study of velocity fields in steady, high-speed, reacting flows. A narrow-linewidth laser source was tuned through an isolated OH absorption line to measure the Doppler-shifted linecenter frequency relative to an iodine reference line. A counterpropagating beam approach was used to eliminate collisional impact shift effects. Pointwise measurements of velocity were made in a unique reacting underexpanded jet facility as an extensive calibration of the technique over a wide range of flow conditions. The extension of the technique to planar measurements is also discussed.

Klavuhn, K. G.↗

Evaluation of single and multiple Doppler lidar techniques to measure complex flow during the XPIA field campaign

Abstract. Accurate three-dimensional information of wind flow fields can be an important tool in not only visualizing complex flow but also understanding the underlying physical processes and improving flow modeling. However, a thorough analysis of the measurement uncertainties is required to properly interpret results. The XPIA (eXperimental Planetary boundary layer Instrumentation Assessment) field campaign conducted at the Boulder Atmospheric Observatory (BAO) in Erie, CO, from 2 March to 31 May 2015 brought together a large suite of in situ and remote sensing measurement platforms to evaluate complex flow measurement strategies. In this paper, measurement uncertainties for different single and multi-Doppler strategies using simple scan geometries (conical, vertical plane and staring) are investigated. The tradeoffs (such as time–space resolution vs. spatial coverage) among the different measurement techniques are evaluated using co-located measurements made near the BAO tower. Sensitivity of the single-/multi-Doppler measurement uncertainties to averaging period are investigated using the sonic anemometers installed on the BAO tower as the standard reference. Finally, the radiometer measurements are used to partition the measurement periods as a function of atmospheric stability to determine their effect on measurement uncertainty. It was found that with an increase in spatial coverage and measurement complexity, the uncertainty in the wind measurement also increased. For multi-Doppler techniques, the increase in uncertainty for temporally uncoordinated measurements is possibly due to requiring additional assumptions of stationarity along with horizontal homogeneity and less representative line-of-sight velocity statistics. It was also found that wind speed measurement uncertainty was lower during stable conditions compared to unstable conditions.

17 WIND ENERGY↗

The effect of a transducer’s spatial averaging on an elastodynamic guided wave’s wavenumber spectrum

Elastodynamic guided waves propagate in an elastic solid which makes it difficult, if not impractical, to place a receiving transducer in the direct path of the propagating wave (as one would for an acoustic wave in a fluid medium). Thus, to account for this, receiving transducers are often placed on the surface of the solid waveguide such that the transducer surface is parallel to the wave propagation direction. This transducer orientation introduces spatial averaging, which causes the received signal to have an altered signal amplitude and mode bias. We investigate both of these effects and present a simple model from which we derive a scaling-ratio expression that describes the effects of spatial averaging. Furthermore, we then test its performance using finite-element simulations that incorporate “real-world” assumptions (e.g., transient waves, piezoelectric effects, etc.). The results from the simulations demonstrate that the scaling-ratio can characterize the effects resulting from spatial averaging. The scaling-ratio expression will be particularly useful when designing experiments involving high frequency (small wavelength) guided waves. Lastly, the proposed scaling-ratio expression could be applied to other sensing methods, like Laser Doppler Vibrometry (LDV) or piezoelectric waveguides with inter-digitated transducers, because of its generality. However, the authors are careful to note that the scaling-ratio expression is not intended as a replacement of multi-physics analysis or good experimental design, and the effects of spatial averaging should be avoided whenever possible.

2DFFT↗

Right Ventricular Tissue Doppler Assessment in Space During Circulating Volume Modification using the Braslet-M Device

This joint U.S. - Russian work aims to establish a methodology for assessing cardiac function in microgravity in association with manipulation of central circulating volume. Russian Braslet-M occlusion cuffs were used to temporarily increase the volume of blood in the lower extremities, which effectively reduces the volume returning to the heart in the central circulation. A novel methodology was tested on the International Space Station (ISS) to assess the volume status of crewmembers by evaluating the responses to application and release of the Braslet-on-occlusion cuffs, as well as to modified Valsalva and Mueller maneuvers. Baseline echocardiographic tissue Doppler imaging (TDI) of the right ventricular free wall with no Braslet applied shows early diastolic E' (16 cm/sec), late diastolic A' (14 cm/sec), and systolic (12 cm/sec) velocities compatible with normal subjects on Earth. TDI of the RV free wall with Braslet applied shows that early diastolic E' decreased by 50% (8 cm/sec), late diastolic A' increased by 45%, and systolic S' remains unchanged. TDI of the RV free wall approximately 8 beats after the Braslet was released shows early diastolic E' (8 cm/sec), late diastolic A' (12 cm/sec), and systolic S' (13 cm/sec) velocities. During this portion of the release, early diastolic E' did not recover to baseline values but late diastolic A' and systolic S' recovered to pre-Braslet values. The pre-systolic cross-sectional area of the internal jugular vein with Braslet off was 1.07 cm(sup 2) and 1.13 cm(sup 2) 10 min after the Braslet was applied. The presystolic cross-sectional area of the common femoral vein with Braslet off was 0.50 cm(sup 2), and was 0.54 cm(sup 2) 10 min after the Braslet was applied. The right ventricular myocardial performance Tei index also was calculated for comparison with typical values found in healthy subjects on Earth. Baseline and Braslet-on values for Tei index were 0.25 and 0.22 respectively. Braslet Tei indices are within normal ranges found in healthy subjects and temporarily become greater than 0.4 during the dynamic Braslet release portion of this study. Tissue Doppler imaging of the right ventricle revealed that the Braslet influenced cardiac preload and that fluid was sequestered in the lower-extremity interstitial and vascular space after only 10 minutes of application. This report demonstrates that Braslet application affects right ventricular physiology in long-duration space flight based on TDI and that this effect is in part due to venous hemodynamics.

Hamilton, D. R.↗