Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Investigation and Analysis of Dolomite Dissolution in Variable Strength Systems Relevant to the WIPP

The Waste Isolation Pilot Plant (WIPP) was opened in 1999 as a solution to the long-term disposal of the nation's nuclear defense-generated transuranic (TRU) waste. The salt beds were recommended as the ideal location because they are free from flowing fresh water, easily mined, impermeable, and geologically stable. However, for performance assessment modeling, release scenarios must be considered. The most likely release scenario was determined to be human intrusion leading to direct and/or long-term brine release (US DOE 1995, US DOE 1996, Perkins et al., 1999). The focus of this research is the Rustler formation because it is located above the WIPP and is the most transmissive layer (Perkins et al., 1999). Objective: To determine the effect of chelating ligands ( e.g. EDTA) on dissolution of dolomite in high ionic strength systems. Do brines impact dolomite dissolution and how is it affected by EDTA binding with cations? By varying the ionic strengths, different brine conditions can be simulated similar to those in and around the Culebra member and evaluate trends of dissolved Ca and Mg in the aqueous phase from the quantified data. Conclusions: <2% of dolomite dissolved over one week at pH 8.5. Greater dissolution occurred at higher ionic strength and in the presence of NaCl with approximately 0.4 vs. 0.9% of Mg removed from dolomite in 0.1 and 1.0 M Na. Further, 0.3 vs. 0.9% of Mg was removed from dolomite in 1.0 M IS CaCl{sub 2} versus NaCl. EDTA increased dissolution of dolomite at low ionic strength due to its strong complexation affinity for Ca/Mg with slightly greater removal of Ca than Mg. Significant differences were not observed at high ionic strength due to the presence of large concentrations of competing cations (Na, Ca, Mg). Slightly higher concentrations of Ca were removed from dolomite than Mg after one week, suggesting either incongruent dissolution or release through ion exchange of Ca from trace mineral impurities. Further, when EDTA was present, it may have increased Ca removal due to its greater complexation for Ca than Mg. Environmental Implications: High ionic strength brines and low ionic strength solutions with organic ligands increase dissolution of dolomite. Due to the long half-lives of radionuclides in the TRU waste, it may be important to consider the long term impact of dolomite dissolution for potential release scenarios.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Influence of Borate on Sorption of Strontium and Barium to Calcium Silicate Hydrate - 20148

Radioactive waste with the decommissioning process at the Fukushima Daiichi Nuclear Power Plant (FDNPP), contains borate with relatively high concentration. As with general low-level wastes, such waste is also assumed the solidification with cementitious materials which calcium silicate hydrate (C-S-H) is one of the main components. In this study, the sorption behavior of strontium (Sr) ions and barium (Ba) ions to C-S-H in the presence of borate was examined by the sorption experiments without drying process. In the sorption experiments, C-S-H was synthesized by the mixture of calcium oxide, fumed silica and a solution with setting the Ca/Si molar ratios to 0.4, 0.8, 1.2 and 1.6. The total amount of a solid phase was 1.5 g, and the total volume of the solution containing borate and adsorbed ions (Sr or Ba) was 30 mL. The concentration of borate was set to 0 M or 0.6 M and the sodium/boron (Na/B) ratios was set to 0.2 or 1.0 by mixing boric acid and sodium hydroxide. The concentration of Sr ions or Ba ions was adjusted to 1 mM. The sorption period was set to 7 days. In the results, the sorption ratios of Sr ions and Ba ions for C-S-H exceeded 80% under all experimental conditions, although the sorption competition of cations with Na ions and the inhibition of the C-S-H formation with generating borate compounds observed by Raman spectroscopy might slightly reduce the sorption of them. These suggest that cationic radionuclides will be immobilized by C-S-H contained in the cements even in the presence of borate. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Materials Design Directions for Solar Thermochemical Water Splitting

The sustainable, economical production of molecular hydrogen is a crucial component of a net zero-greenhouse-gas-emissions future. Solar thermochemical water splitting (STWS) offers a renewable route to hydrogen with the potential to help decarbonize several industries, including transportation, manufacturing, mining, metals processing, and electricity generation, as well as provide sustainable hydrogen as a chemical feedstock. STWS uses high temperatures generated from concentrated sunlight or other sustainable means for high-temperature heat to produce hydrogen and oxygen from steam. For example, in its simplest form of a two-step thermochemical cycle, a redox-active metal oxide is heated to ≈1700-2000 K, driving off molecular oxygen while producing oxygen vacancies in the material. The reduced metal oxide then cools (ideally with the extracted heat recuperated for re-use) and, in a separate step, comes into contact with steam, which reacts with oxygen vacancies to produce molecular hydrogen while recovering the original state of the metal oxide. Despite its promising use of the entire solar spectrum to split water thermochemically, the current estimated cost of hydrogen produced via STWS is ≈4-6× the U.S. Department of Energy (DOE) Hydrogen Shot target value of $1/kg. One contributing approach to bridging this cost gap is the design of new materials with improved thermodynamic properties to enable higher efficiencies. The state-of-the-art (SOA) redox-active metal oxide for STWS is ceria (CeO 2 ), due to its close to optimal, although too high, oxygen vacancy formation enthalpy and large configurational and electronic entropy of reduction. However, ceria requires high operating temperatures and its efficiency is insufficient. Therefore, efforts to increase the efficiency of STWS cycles have focused on further optimizing oxygen vacancy formation enthalpies and augmenting the reduction entropy via substitution or doping and materials discovery schemes. Examples of the latter include the perovskites BaCe 0.25 Mn 0.75 O 3 and (Ca,Ce)(Ti,Mn)O 3 . These efforts and others have revealed intuitive chemical principles for the efficient and systematic design of more effective materials, such as the strong correlation between the enthalpies of crystal bond dissociation and solid-state cation reduction with the enthalpy of oxygen vacancy formation, as well as configurational entropy augmentation via the coexistence of two or more redox-active cation sublattices. The purpose of this chapter is to prepare the reader with an up-to-date account of STWS redox-active materials, both the SOA and promising newcomers, as well as to provide chemically intuitive strategies for improving their cycle efficiencies through materials design – in conjunction with ongoing efforts in reactor engineering and gas separations – to reach the cost points for commercial viability. First, we will introduce the thermodynamics of STWS using a two-step, metal-oxide, thermochemical cycle with economics in mind. We also will compare the pros and cons of processes that do or do not involve phase changes. Second, we will describe the qualities that make ceria the SOA STWS redox-active material, as well as its limitations. Third, we will survey some of the most promising candidates to date in the search for materials to supplant ceria, emphasizing the post-ternary, metal-oxide-perovskite alloys. Lastly, we will enumerate and discuss the following materials design directions for STWS redox-active materials: crystal reduction potentials as a proxy for oxygen vacancy formation enthalpies, engineering the electronic and configurational entropy of reduction via f-shells and simultaneous redox, and vetting materials stability via temperature-dependent phase diagrams and melting-point prediction.

08 HYDROGEN↗
DOE OSTI2020

Identifying Photoinduced Dipolar Polarization and Orbit–Orbit Interaction between Excitons in Organic–Inorganic Hybrid Perovskites

Abstract Photoinduced polarization and orbit–orbit interaction are important issues in hybrid perovskites toward developing optoelectronic functionalities. This paper identifies that photoinduced polarization occurs in hybrid perovskites with mixed‐cation methylammonium (MA)/formamidinium (FA) (MA x FA (1− x ) PbI 3 ) by measuring bulk polarization at 1 MHz in a magnetic field. Interestingly, when the internal dipole moment is increased upon increasing the MA:FA ratio, the photoinduced dipolar polarization can be substantially enhanced, clarifying the controversial issue of whether photoexcitation can induce a dielectric polarization within dipolar polarization regime in hybrid perovskites. Furthermore, upon increasing photoinduced dipolar polarization, it is found that the intrinsic orbit–orbit interaction between excitons can be increased, revealed by monitoring photocurrent change (Δ J sc ) upon switching the photoexcitation between linear and circular polarizations. This presents that organic cations are directly involved in the orbit–orbit interaction within band structures. Clearly, the studies provide an insightful understanding of the dipole moment effects on photoinduced dipolar polarization and orbit–orbit interaction between excitons in hybrid perovskites toward controlling the optoelectronic properties.

Dou, Yixuan↗
DOE OSTI2021

Insight into the Solid Electrolyte Interphase Formation in Bis(fluorosulfonyl)Imide Based Ionic Liquid Electrolytes

The formation of the solid electrolyte interphase (SEI) in an ionic liquid electrolyte of 0.5 m lithium bis(fluorosulfonyl)imide (LiFSI) in 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide at high cell voltages (1.7–1.9 V) is investigated in ordered mesoporous carbon (OMC) based Li metal cells using an operando small-angle neutron scattering (SANS) technique coupled with electrochemical impedance spectroscopy and ex situ X-ray photoelectron spectroscopy (XPS). It is demonstrated that discharging the OMC Li metal cells to ≈2 V and holding the cell voltage constant induces a rapid current increase with time, confirming extensive reduction and SEI formation. XPS analysis reveals that LiF is formed at open cell voltage (OCV), which is attributed to the carbenes generated at the lithium negative electrode because of its reaction with EMIm cation diffusing to and initiating the reaction with FSI - anions at the carbon positive electrode. It is confirmed that the chemical reaction at OCV and electrochemical reduction at high cell voltage of the FSI - anion plays a protective role against EMIm cation co-intercalation into the carbon positive electrode during the initial discharge. Operando SANS studies also suggest that slight differences occur in the surface composition and reaction mechanism as a function of cell voltage.

1-ethyl-3- methylimidazolium bis(fluorosulfonyl)im↗
DOE OSTI2021

Ion Pair Uptake in Ion Gel Devices Based on Organic Mixed Ionic–Electronic Conductors

Abstract In organic mixed ionic–electronic conductors (OMIECs), it is critical to understand the motion of ions in the electrolyte and OMIEC. Generally, the focus is on the movement of net charge during gating, and the motion of neutral anion–cation pairs is seldom considered. Uptake of mobile ion pairs by the semiconductor before electrochemical gating (passive uptake) can be advantageous as this can improve device speed, and both ions can participate in charge compensation during gating. Here, such passive ion pair uptake in high‐speed solid‐state devices is demonstrated using an ion gel electrolyte. This is compared to a polymerized ionic liquid (PIL) electrolyte to understand how ion pair uptake affects device characteristics. Using X‐ray photoelectron spectroscopy, the passive uptake of ion pairs from the ion gel into the OMIEC is detected, whereas no uptake is observed with a PIL electrolyte. This is corroborated by X‐ray scattering, which reveals morphological changes to the OMIEC from the uptake of ion pairs. With in situ Raman, a reorganization of both anions and cations is then observed during gating. Finally, the speed and retention of OMIEC‐based neuromorphic devices are tuned by controlling the freedom of charge motion in the electrolyte.

Quill, Tyler J.↗
DOE OSTI2022

Investigating Particle Size‐Dependent Redox Kinetics and Charge Distribution in Disordered Rocksalt Cathodes

Abstract Understanding how various redox activities evolve and distribute in disordered rocksalt oxides (DRX) can advance insights into manipulating materials properties for achieving stable, high‐energy batteries. Herein, the authors present how the reaction kinetics and spatial distribution of redox activities are governed by the particle size of DRX materials. The size‐dependent electrochemical performance is attributed to the distinct cationic and anionic reaction kinetics at different sizes, which can be tailored to achieve optimal capacity and stability. Overall, the local charged domains in DRX particles display random heterogeneity caused by the isotropic delithiation pathways. Owing to the kinetic limitation, the micron‐sized particles exhibit a holistic “core‐shell” charge distribution, whereas sub‐micron particles show more uniform redox reactions throughout the particles and ensembles. Sub‐micron DRX particles exhibit increasing anionic redox activities yet inferior cycling stability. In summary, engineering particle size can effectively modulate how cationic and anionic redox activities evolve and distribute in DRX materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Benzimidazole Based Hole‐Transporting Materials for High‐performance Inverted Perovskite Solar Cells

Abstract Interfaces play a decisive role in perovskite solar cells’ power conversion efficiency and their long‐term durability. Small‐molecule hole‐transporting materials (HTMs) have grabbed enormous attention due to their structural flexibility, material properties, and stabilities, allowing for improved operational durability in perovskite photovoltaics. This study synthesizes and investigates a new class of benzimidazole‐based small molecules, named YJS001 and YJS003 , serving as the HTMs to enable high‐efficiency mixed‐cation mixed‐halide perovskite solar cells. The benzimidazole‐based materials are dopant‐free HTMs composed of donor and acceptor building blocks that are designed to engineer the energy level alignment near the HTM/perovskite interface. Mixed‐cation mixed‐halide perovskites can be grown uniformly on both HTMs with large crystalline grains. It is discovered that the donor‐rich YJS003 ‐based solar cell exhibits a high open‐circuit voltage of 1.09 V with a champion power conversion efficiency of over 20%. Power‐dependent current–voltage characteristics of the solar cells are analyzed, from which the high performance of YJS003's excellent hole mobility and well‐aligned energy level is attributed. This work introduces a new class of benzimidazole‐based small molecules as HTMs, that paves the path for dopant free interface material development for commercialization of perovskite solar cells.

14 SOLAR ENERGY↗
DOE OSTI2022

Structural Damage and Recrystallization Response of Garnet Crystals to Intense Electronic Excitation

Here, the susceptibility to irradiation-induced damage, the fundamental mechanism of the relaxation kinetics, and the corresponding recrystallization effect related to the cation radius ratio are comprehensively investigated for Y 3 Al 5 O 12 and Gd 3 Ga 5 O 12 garnet crystals under 645 MeV Xe 35+ irradiation with different fluences of 5 × 10 11 –3 × 10 12 ions cm –2 . Regarding different lattice distortion and swelling levels, the observed microstructure transformations to disordered and amorphous phases, and corresponding hillock dimensions, consistently confirm that Gd 3 Ga 5 O 12 has a higher susceptibility to radiation damage than Y 3 Al 5 O 12 . Combined with iTS model calculations, although Y 3 Al 5 O 12 has higher atomic temperature and energy deposition than Gd 3 Ga 5 O 12 under the same ion velocity and electronic energy loss, the relatively high thermal conductivity and specific heat coefficient of Y 3 Al 5 O 12 crystals enhance the conduction and dissipation of deposition energy, and Gd 3 Ga 5 O 12 , with a higher cation-radius-ratio (r A /r B ), is more easily damaged to amorphous phase due to the less favorable kinetics of ordering and recovery of a melted track region to the crystalline phase. Additionally, the significant bandgap modification in spectral ranges of 5.88–6.75 eV for Y 3 Al 5 O 12 and 4.83–5.41 eV for Gd 3 Ga 5 O 12 , and the enhancement of defect-assisted-related luminescence are achieved, providing a basis to design novel optoelectronic devices in microelectronics fields.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhanced Optical Contrast and Switching in Near‐Infrared Electrochromic Devices by Optimizing Conjugated Polymer Oligo(Ethylene Glycol) Sidechain Content and Gel Electrolyte Composition

Abstract A detailed investigation addressing the effects of functionalizing conjugated polymers with oligo(ethylene glycol) (EG n ) sidechains on the performance and polymer‐electrolyte compatibility of electrochromic devices (ECDs) is reported. The electrochemistry for a series of donor‐acceptor copolymers having near‐infrared (NIR)‐optical absorption, where the donor fragment is 3,4‐ethylenedioxythiophene (EDOT) or an EG n functionalized bithiophene (g2T) and the acceptor fragment is diketopyrrolopyrrole (DPP) functionalized with branched alkyl or EG n sidechains, is extensively probed. ECDs are next fabricated and it is found that EG n sidechain incorporation must be finely balanced to promote polymer‐electrolyte compatibility and provide efficient ion exchange. Proper electrolyte‐cation pairing and polymer structural tuning affords a 2x increase in optical contrast (from 12% to 24%) and >60x reduction in switching time (from 20 to 0.3 s). Atomic force microscopy (AFM)/grazing incidence wide‐angle X‐ray scattering (GIWAXS) characterization of the polymer film morphology/microstructure reveals that an over‐abundance of EG n sidechains generates large polymer crystallites, which can suppress ion exchange. Lastly, time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) indicates sidechain/electrolyte identity does not influence the electrolyte penetration depth into the films, and EG n sidechain inclusion increases electrolyte cation uptake. The material structural design insight and guidelines regarding the polymer‐electrolyte ion insertion/expulsion dynamics reported here should be of significant utility for developing next‐generation mixed ionic‐electronic conducting materials.

Chemistry↗
DOE OSTI2020

Low Current and Analog Memristor with Ru as Mobile Species

The switching parameters and device performance of memristors are predominately determined by their mobile species and matrix materials. Devices with oxygen or oxygen vacancies as the mobile species usually exhibit a great retention but also need a relatively high switching current (e.g., >30 mu A), while devices with Ag or Cu as cation mobile species do not require a high switching current but usually show a poor retention. Here, Ru is studied as a new type of mobile species for memristors to achieve low switching current, fast speed, good reliability, scalability, and analog switching property simultaneously. An electrochemical metallization-like memristor with a stack of Pt/Ta2O5/Ru is developed. Migration of Ru ions is revealed by energy-dispersive X-ray spectroscopy mapping and in situ transmission electron microscopy within a sub-10 nm active device area before and after switching. The results open up a new avenue to engineer memristors for desired properties.

analog switching↗
DOE OSTI2020

Quasi‐Binary Transition Metal Dichalcogenide Alloys: Thermodynamic Stability Prediction, Scalable Synthesis, and Application

Abstract Transition metal dichalcogenide (TMDCs) alloys could have a wide range of physical and chemical properties, ranging from charge density waves to superconductivity and electrochemical activities. While many exciting behaviors of unary TMDCs have been demonstrated, the vast compositional space of TMDC alloys has remained largely unexplored due to the lack of understanding regarding their stability when accommodating different cations or chalcogens in a single‐phase. Here, a theory‐guided synthesis approach is reported to achieve unexplored quasi‐binary TMDC alloys through computationally predicted stability maps. Equilibrium temperature–composition phase diagrams using first‐principles calculations are generated to identify the stability of 25 quasi‐binary TMDC alloys, including some involving non‐isovalent cations and are verified experimentally through the synthesis of a subset of 12 predicted alloys using a scalable chemical vapor transport method. It is demonstrated that the synthesized alloys can be exfoliated into 2D structures, and some of them exhibit: i) outstanding thermal stability tested up to 1230 K, ii) exceptionally high electrochemical activity for the CO 2 reduction reaction in a kinetically limited regime with near zero overpotential for CO formation, iii) excellent energy efficiency in a high rate Li–air battery, and iv) high break‐down current density for interconnect applications. This framework can be extended to accelerate the discovery of other TMDC alloys for various applications.

Hemmat, Zahra↗
DOE OSTI2020

Unraveling the Crystallization Kinetics of 2D Perovskites with Sandwich-Type Structure for High-Performance Photovoltaics

2D perovskite solar cells with high stability and high efficiency have attracted significant attention. A systematical static and dynamic structure investigation is carried out to show the details of 2D morphology evolution. A dual additive approach is used, where the synergy between an alkali metal cation and a polar solvent leads to high-quality 2D perovskite films with sandwich-type structures and vertical phase segregation. Such novel structure can induce high-quality 2D slab growth and reduce internal and surface defects, resulting in a high device efficiency of 16.48% with enhanced continuous illumination stability and improved moisture (55-60%) and thermal (85°C) tolerances. Transient absorption spectra reveal the carrier migration from low n to high n species with different kinetics. An [PbI 6 ] 4- octagon coalescence transformation mechanism coupled with metal and organic cations wrapped is proposed. By solvent vapor annealing, a recrystallization and reorientation of the 2D perovskite slabs occurs to form an ideal structure with improved device performance and stability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stabilizing Anionic Redox Chemistry in a Mn-Based Layered Oxide Cathode Constructed by Li-Deficient Pristine State

Li-rich cathode materials are of significant interest for coupling anionic redox with cationic redox chemistry to achieve high-energy-density batteries. However, lattice oxygen loss and derived structure distortion would induce serious capacity loss and voltage decay, further hindering its practical application. Herein, a novel Li-rich cathode material, O3-type Li 0.6 [Li 0.2 Mn 0.8 ]O 2 , is developed with the pristine state displaying both a Li excess in the transition metal layer and a deficiency in the alkali metal layer. Benefiting from stable structure evolution and Li migration processes, not only can high reversible capacity (≈329 mAh g -1 ) be harvested but also irreversible/reversible anionic/cationic redox reactions are comprehensively assigned via the combination of in/ex situ spectroscopies. Furthermore, irreversible lattice oxygen loss and structure distortion are effectively restrained, resulting in long-term cycle stability (capacity drop of 0.045% per cycle, 500 cycles). Altogether, tuning the Li state in the alkali metal layer presents a promising way for modification of high-capacity Li-rich cathode candidates.

anionic redox reactions↗
DOE OSTI2021

Quantifying Anionic Diffusion in 2D Halide Perovskite Lateral Heterostructures

Anionic diffusion strongly impacts the stability of halide perovskite materials, but it is still not well understood. Here, a quantitative investigation of in-plane thermally driven anionic inter-diffusion in a series of novel 2D and quasi-2D halide perovskites lateral heterostructures is reported. The calculated diffusion coefficients (D) reveal the inhibition of Br–I inter-diffusion with bulky π-conjugated organic cations compared with short-chain aliphatic organic cations. Furthermore, halide diffusion is found to be faster in quasi-2D (n > 1) than 2D perovskites (n = 1). The increment becomes less apparent as the “n” number increases, akin to the quantum confinement effect observed for band gaps. These trends are rationalized by molecular dynamics simulations of free energy barriers for halide diffusion that reveal mechanisms for suppressing diffusion. We report this work provides important fundamental insights on the anionic migration and diffusion process in halide perovskite materials.

2D materials↗
DOE OSTI2022

Gradient Doping in Sn–Pb Perovskites by Barium Ions for Efficient Single-Junction and Tandem Solar Cells

Narrow bandgap tin-lead (NBG Sn-Pb) perovskites generally have a high density of unintentional p-type self-doping, which reduces the charge carrier lifetimes, diffusion lengths and device efficiencies. Here, we demonstrate a p-n homojunction across the Sn-Pb perovskite resulted from a gradient doping by Ba 2+ . We report that 0.1 mol% Ba 2+ can effectively compensate the p-doping of Sn-Pb perovskites or even turns it to n-type without changing its bandgap. Ba 2+ cations are found to stay at the interstitial sites and work as shallow electron donor. In addition, Ba 2+ cations show a unique heterogeneous distribution in perovskite film. Most of the barium ions stay in the top 600 nanometer region of the perovskite films and turn it into weakly n-type, while the bottom portion of the film remains to be p-type. The gradient doping forms of a homojunction from top to bottom of the perovskite films with a built-in field that facilitates extraction of photogenerated carriers, resulting an increased carrier extraction length. Furthermore, this strategy enhanced the efficiency of Sn-Pb perovskite single-junction solar cells to over 21.0% and boosted the efficiencies of monolithic perovskite-perovskite tandem solar cells to 25.3% and 24.1%, for active areas of 5.9 mm2 and 0.94 cm 2 , respectively.

14 SOLAR ENERGY↗
DOE OSTI2022

Atomically Thin, Ionic–Covalent Organic Nanosheets for Stable, High–Performance Carbon Dioxide Electroreduction

The incorporation of charged functional groups is effective to modulate the activity of molecular complexes for the CO 2 reduction reaction (CO 2 RR), yet long-term heterogeneous electrolysis is often hampered by catalyst leaching. Herein, an electrocatalyst of atomically thin, cobalt-porphyrin-based, ionic–covalent organic nanosheets (CoTAP-iCONs) is synthesized via a post-synthetic modification strategy for high-performance CO 2 -to-CO conversion. The cationic quaternary ammonium groups not only enable the formation of monolayer nanosheets due to steric hindrance and electrostatic repulsion, but also facilitate the formation of a *COOH intermediate, as suggested by theoretical calculations. Consequently, CoTAP-iCONs exhibit higher CO 2 RR activity than other cobalt-porphyrin-based structures: an 870% and 480% improvement of CO current densities compared to the monomer and neutral nanosheets, respectively. Additionally, the iCONs structure can accommodate the cationic moieties. In a flow cell, CoTAP-iCONs attain a very small onset overpotential of 40 mV and a stable total current density of 212 mA cm –2 with CO Faradaic efficiency of >95% at –0.6 V for 11 h. Further coupling the flow electrolyzer with commercial solar cells yields a solar-to-CO conversion efficiency of 13.89%. Finally, this work indicates that atom-thin, ionic nanosheets represent a promising structure for achieving both tailored activity and high stability.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Revealing the Anion–Solvent Interaction for Ultralow Temperature Lithium Metal Batteries

Anion solvation in electrolytes can largely change the electrochemical performance of the electrolytes, yet has been rarely investigated. Herein, three anions of bis(trifluoromethanesulfonyl)imide (TFSI), bis(fluorosulfonyl)imide (FSI), and derived asymmetric (fluorosulfonyl)(trifluoro-methanesulfonyl)imide (FTFSI) are systematically examined in a weakly Li + cation solvating solvent of bis(3-fluoropropyl)ether (BFPE). In-situ liquid secondary ion mass spectrometry demonstrates that FTFSI - and FSI - anions are associated with BFPE solvent, while weak TFSI - /BFPE cluster signals are detected. Molecular modeling further reveals that the anion–solvent interaction is accompanied by the formation of H-bonding-like interactions. Further, anion solvation enhances the Li + cation transfer number and reduces the organic component in solid electrolyte interphase, which enhances the Li plating/stripping Coulombic efficiency at a low temperature of -30 °C from 42.4% in TFSI-based electrolytes to 98.7% in 1.5 m LiFTFSI and 97.9% in LiFSI-BFPE electrolytes. The anion–solvent interactions, especially asymmetric anion solvation also accelerate the Li + desolvation kinetics. The 1.5 m LiFTFSI-BFPE electrolyte with strong anion–solvent interaction enables LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811)||Li (20 µm) full cell with stable cyclability even under -40 °C, retaining over 92% of initial capacity (115 mAh g -1 , after 100 cycles). The anion–solvent interactions insights allow to rational design the electrolyte for lithium metal batteries and beyond to achieve high performance.

25 ENERGY STORAGE↗