Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COPPER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Compositional and Thermal Characterization of Potential Nano-Carbon Copper Composite

Covetic materials have been claimed to be new types of metal matrix nano-composite materials. These materials are formed from face-centered-cubic metals which are alleged to be super-saturated with up to ~ 10 wt pct of activated nano-carbon. The focus of this study was to characterize the chemical composition of copper covetic materials of varying nano-carbon concentrations, and characterize the thermal properties of these materials in order to determine if these materials exhibit enhanced material properties.

36 MATERIALS SCIENCE↗

Study of the Influence of Xanthate Derivative Structures on Copper Sulfide Mineral Adsorption Under Acidic Conditions

Adsorption of commercial xanthate derivatives on copper sulfide mineral (covellite, CuS) was studied by kinetics and isotherm adsorption experiments. The adsorption of xanthate derivatives was confirmed by FTIR (Fourier transform infrared spectroscopy) and XPS (X-ray photoelectron spectroscopy) results. Experiments were performed with two different xanthate derivatives, C-4410 (O-pentyl S-2-propenyl ester) and C-4940 (isobutyl xanthogen ethyl formate), on individual doses of 0.05 g of powdered covellite. It was found that the equilibrium times at pH 2, 4, and 6 were different for both xanthate derivatives. The shortest times were achieved at pH 2 and 4. The results suggest that C-4110 can be used as collector in a wide range of pH, while C-4940 is limited to lower pH values. Pseudo first- and pseudo second-order kinetics models were thus applied to the experimental data for pH 2. The information obtained from the kinetics models combined with XPS allowed proposing the adsorption mechanism for the covellite-xanthate derivative pair. The adsorption takes place through a non-covalent interaction for C-4410 and chemisorption process for C-4940. The best-fitting isotherm models for C-4410 and C-4940 adsorption were Redlich–Peterson and Freundlich, respectively, which yield a maximum adsorption capacity of 57.07 mg g{sup −1} for C-4410 and 44.62 mg g{sup −1} for C-4940.

36 MATERIALS SCIENCE↗

Accelerated Oxygen Mass Transfer in Copper and Vanadium Oxide-Based MIEC-Redox Membrane

Mixed ionic-electronic conducting (MIEC) membranes have a great potential for use in gas separation technology in the production of pure oxygen for metallurgy, micro- and nanoelectronics, biotechnology, pharmaceutics, etc. Before this happens, an important issue has to be addressed. This issue involves the design of novel MIEC membranes with enhanced oxygen transport. Recently, a concept of thick two-layer solid/liquid composite MIEC-Redox membranes with accelerated diffusion-bubbling oxygen transfer was proposed (see Belousov and Fedorov in ACS Appl Mater Interfaces 10:21794–21798, 2018). These diffusion-bubbling membranes could serve for efficient oxygen separation from air. However, there is no enough fundamental understanding of the mass transport processes involved. This understanding is important for evaluating the potential of MIEC-Redox membranes for practical application. The presented article gives a theory of oxygen mass transfer in two-layer copper and vanadium oxide-based MIEC-Redox membranes. The theory describes both the transport of oxygen ions in the outer layer of the membrane and the nucleation, growth, and transport of oxygen gas bubbles in the inner layer of the membrane. Kinetic regularities of oxygen mass transfer are established. The ways to enhance the productivity of MIEC-Redox membranes are outlined.

36 MATERIALS SCIENCE↗

Microstructure Evolution and Failure Analysis of an Aluminum–Copper Cathode Conductive Head Produced by Explosive Welding

In this paper, microstructure evolution and failure analysis of the aluminum-copper interface of cathode conductive heads during their use were studied. The interface morphologies, compositions, conductivity and mechanical properties were investigated and analyzed. Obvious corrosion was found on the surface of the contact interface, which was more prevalent on an Al matrix. The crack increased sharply in the local metallurgical bonding areas on the interface, with the compound volume having no significant change. The phase transformation occurred on the interface during use, which was investigated using the elemental composition and x-ray diffraction pattern. The microhardness near the interface increased accordingly. An obvious electrical conductivity decrease appeared on the Al/Cu interface of the cathode conductive head after use over a specific time interval. Therefore, the deterioration of the microstructures and corrosion are the primary factors that affect the electrical conductivity and effective bonding, which will lead to eventual failure.

36 MATERIALS SCIENCE↗

Fiber Laser Welding–Brazing Characteristics of Dissimilar Metals AZ31B Mg Alloys to Copper with Mg-Based Filler

Fiber laser welding–brazing of 1-mm-thick AZ31B Mg alloys to 1.5-mm-thick copper (T2) with Mg-based filler was performed in a lap configuration. The weld appearance, interfacial microstructure and mechanical properties were investigated with different heat inputs. The results indicated that processing windows for optimizing appropriate welding parameters were relatively narrow in this case. Visually acceptable joints with certain strength were achieved at appropriate welding parameters. The maximum tensile-shear fracture load of laser-welded-brazed Mg/Cu joint could reach 1730 N at the laser power of 1200 W, representing 64.1% joint efficiency relative to AZ31Mg base metal. The eutectic structure (α-Mg + Mg{sub 2}Cu) and Mg-Cu intermetallic compound was observed at the Mg/Cu interface, and Mg-Al-Cu ternary intermetallic compound were identified between intermetallics and eutectic structure at high heat input. All the joints fractured at the Mg-Cu interface. However, the fracture mode was found to differ. For laser power of 1200 W, the surface was characterized by tearing edge, while that with poor joint strength was almost dominated by smooth surface or flat tear pattern.

36 MATERIALS SCIENCE↗

Design and Performance Evaluation of Al{sub 2}O{sub 3}-SiC Composite for Direct-Bonded Copper Substrate

A computational material design approach is applied to propose a novel ceramic material for direct-bonded copper (DBC) substrate with enhanced thermal and structural performance. The material design inherently consists of many competing requirements that require careful decisions regarding key trade-offs in terms of material composition, inclusion size, shape, and distribution to achieve the target properties. The alumina-silicon (Al{sub 2}O{sub 3}-SiC) composite, as compared to commercial alumina, used in DBC is found to be the most suitable design among other candidates with improved thermal and structural properties. In order to study the performance characteristics and the effects of the new ceramic composite with improved properties in terms of structural behavior and fatigue life of the DBC substrate, the normal working and extreme thermal cycling conditions were simulated and analyzed using finite element method. The temperature, strain, and localized stress distribution within the substrate at a steady-state condition were analyzed, and the improved Coffin–Manson law was used to calculate the fatigue life of the substrate under extreme thermal cycling conditions. The proposed Al{sub 2}O{sub 3}-SiC composite is found to be more robust than the commercial alumina as DBC substrates considering the thermal–mechanical performance. The fatigue life cycle of the DBC substrate with the proposed material is predicted to be about two times longer than the commercial alumina DBC ceramic under transient thermal cycling test.

36 MATERIALS SCIENCE↗

Investigation of Current Parameters and Size Effects on Mechanical Properties During Pulsed Electrically Assisted Uniaxial Tension in T2 Red Copper Sheets

It has been found that the electrically assisted (EA) forming can alleviate size effects due to the electroplastic effect. Size effects exist in the manufacture of tiny workpieces and severely affect material performances because the grain boundary hardening effect and strong anisotropy of the mechanical properties of the grains will lead to a strong variation in the forming properties of the sheet. In order to investigate the influences of current parameters and size effects on mechanical properties in EA forming, EA uniaxial tension tests with varying grain size and thickness were conducted on T2 red copper sheets. The small temperature rise shows the thermal effect is slight; the flow stress decreases with the increase in pulse frequency, pulse duty ratio and current density; the finer grains still result in higher strength and better plasticity; Moreover, the fluctuations of tensile strength, maximum uniform strain and fracture strain decrease with the increase in the ratio of thickness to grain size (N) at constant current density, which means pulsed current can weaken size effects.

36 MATERIALS SCIENCE↗

Dynamic Frictional Characteristics of TP2 Copper Tubes during Hydroforming under Different Loading and Fluid Velocities

Tube hydroforming (THF) experiments were performed on TP2 copper tubes under different loading velocities and fluid velocities using a self-developed measurement system to investigate dynamic frictional characteristics in the guiding zone. The results show that the coefficient of friction (COF) dynamically changes during forming experiments and decreases with tube deformation. The average descending rate and amplitude of the COF increase with increasing loading velocity. Microscopically, the micro-protrusions on the tubular surface are flattened, and the surface scratches are finer and more uniform, as the loading velocity increases, resulting in a decrease in COF. At the same external loading velocity, the COF increases with increasing fluid velocity and is also extremely sensitive to it. Moreover, improving and predicting the formability of such tubes by accurately adjusting and controlling fluid velocity in THF is valuable and critical for the future.

36 MATERIALS SCIENCE↗

Effects of Transition Layer on Bending Resistance in Copper-Clad Aluminum Composite Casting

The performance of the transition layer in a Cu/Al composite casting directly affects the quality of subsequent plastic deformation processing; however, there are no universal or standardized measurement indices for the performance of the transition layer. In this study, Cu/Al composite castings were prepared using the pouring aluminum method, and the resulting solidification microstructures on the bending resistance were investigated. The results of this study lay a theoretical foundation for the development of the plastic processing technologies of these composite castings. A thinner transition layer in the Cu/Al composite casting led to improved bending resistance. In addition, for a fixed total thickness of the transition layer, the bending resistance was mainly controlled by the γ/β interface and β + eutectic (α + β) microstructure, and the thickness of the γ phase had a negligible effect on the bending resistance. The γ/β interface cracked first when the transition layer bore the tensile and shear stress during the bending process, which resulted in the transition layer easily separating from the copper. The bending resistance of the transition layer can be feasibly judged by measuring the bending angle of the specimen tip, which can be easily performed when the specimen bends toward the aluminum direction, suggesting that our proposed method has considerable practical significance.

36 MATERIALS SCIENCE↗

Nickel-Coated Super-Aligned Carbon Nanotube Reinforced Copper Composite for Improved Strength and Conductivity

Nickel (Ni)-coated super-aligned carbon nanotube (SACNT) films-reinforced copper (Cu) matrix composites were fabricated by electrodeposition. The microstructure, mechanical property and electrical conductivity of the prepared composites have been studied systematically. The results show that the mechanical properties of SACNT/Cu were significantly improved by coating SACNT with Ni. When the volume fraction of SACNT is 10.0%, the tensile strength and yield strength of the composite can reach 477.8 and 295.5 MPa, respectively, corresponding to 147 and 170% improvement compared to pure Cu prepared by the same method. Meanwhile, due to the super-aligned arrangement of SACNTs and the homogeneous distribution of Ni, which is not mixing or dissolving with Cu, the conductivities of all the Ni-coated SACNT-reinforced Cu composites are above 58% IACS, which is about 4 times higher than the results in previous research. The enhancement of the strength of the SACNT/Cu composites comes from the combined contribution of load transfer and grain refinement strengthening.

36 MATERIALS SCIENCE↗

Deformation Behavior of Pure Copper Castings with As-Cast Surfaces for Electrical Parts

Herein, the tensile deformation behavior of pure copper castings with as-cast surfaces was investigated. It was found that small and sufficiently large uniform elongation types corresponded, respectively, to the presence or absence of a Cu-Cu{sub 2}O eutectic phase in the microstructure. Fissure defects were observed near the as-cast surfaces when the eutectic phase was present, probably leading to stress concentration. On the other hand, surface pinholes were observed when the eutectic phase was absent, and these were not prevented by directional solidification. Although the as-cast specimens (non-directionally solidified) exhibited a slightly reduced uniform elongation compared to the machined specimens in the absence of the eutectic phase, the directionally solidified as-cast samples exhibited a uniform elongation that was similar to that of the machined specimens. In addition, micropore arrays were formed along the grain boundaries inside the castings when the eutectic phase was absent, whereas almost no micropores were observed inside the directionally solidified as-cast specimens because the solidification process involved a faster cooling rate and/or higher temperature gradient. These results do not only suggest the existence of surface pinholes but also indicate that microporosity can reduce the cross-sectional area of the specimens, thus, affecting their uniform elongation.

36 MATERIALS SCIENCE↗

Correlations Between Spall Damage Mode Preference and Microstructure in Shocked Polycrystalline Copper: A 3-D X-Ray Tomography Study

Nondestructive characterization techniques are essential for maximizing the amount of high fidelity data obtained from post mortem mechanically tested materials, particularly for the complex experimental techniques used for shock loading. Polycrystalline copper samples of varying thermomechanical histories were shock loaded to induce incipient spall damage conditions via plate impacts at low pressures. Electron backscattering diffraction (EBSD) and 3-D X-ray tomography (XRT) were utilized to obtain microstructural and void volume data, respectively. Voids were fit to ellipsoids using their inertia tensors obtained from the 3-D XRT data, and the results compared to EBSD data. This, in turn, enabled establishing quantitative correlations between void shapes and preferential damage mode, either inter- or trans-granular, for each thermomechanical history. Greater than 60 % of voids present in heat-treated samples were spherical, indicative of transgranular damage preference. Greater than 90 % of voids present in as-received rolled samples were flat sheetlike voids or unsymmetrical oblate ellipsoids, indicative of intergranular and coalesced damage modes. Analyzing grain boundary damage statistics in conjunction with global damage mode distributions indicate that boundaries become less dominant as preferential void nucleation sites within the spall plane as the bulk strength of the material decreases from heat treatments.

Microstructure↗

A study of the interactive effects of strain, strain rate and temperature in severe plastic deformation of copper

The deformation field in machining was controlled to access a range of deformation parameters—strains of 1–15, strain rates of 10–100,000 s –1 and temperatures of up to 0.4 T m —in the severe plastic deformation (SPD) of copper. This range is far wider than has beenaccessed to date in conventional SPD methods, enabling a study of the interactive effects of the parameters on microstructure andstrength properties. Nano-twinning was demonstrated at strain rates as small as 1000 s –1 at 196 °C and at strain rates of ≥10,000 s –1 even when the deformation temperature was well above room temperature. Bi-modal grain structures were produced ina single stage of deformation through in situ partial dynamic recrystallization. Furthermore, the SPD conditions for engineering specific microstructuresby deformation rate control are presented in the form of maps, both in deformation parameter space and in terms of the Zener–Hollomon parameter. 20

36 MATERIALS SCIENCE↗

Disordered long-range internal stresses in deformed copper and the mechanisms underlying plastic deformation

The strength of wavy glide metals increases dramatically during deformation as dislocations multiply and entangle, forming dense dislocation wall structures. Numerous competing models have been proposed for this process but experimental validation and guidance for further model development require new experimental approaches capable of resolving local stresses within the dislocation microstructure. We use three-dimensional X-ray microscopy combining submicrometer spatial resolution with diffracted-beam masking to make direct measurements of axial elastic strain (and thus stress) in individual dislocation cell walls and their adjacent cell interiors in heavily deformed copper. These spatially resolved measurements show broad, asymmetric distributions of dipolar stresses that directly discriminate between long-standing deformation models and demonstrate that the distribution of local stresses is statistically connected to the global behavior through simple rules.

36 MATERIALS SCIENCE↗

Effect of ZrO 2 , Al 2 O 3 and La 2 O 3 on cobalt–copper catalysts for higher alcohols synthesis

In this work three cobalt–copper catalysts singly promoted with La, Zr, or Al were studied for catalytic conversion of syngas to higher alcohols. The properties of the promoted catalysts have been characterized by TPR, XRD, XPS and BET. CO hydrogenation was carried out in a plug-flow reactor under 30 bar, GHSV = 36000 scc/g cat /h, H 2 /CO = 2, and 250 °C at differential conversions. The catalyst activity and selectivity to higher alcohols are greatest on CuCoLa 2 O 3 :ethanol selectivity 10.5% at a conversion of 0.76%. During 9 h of time-on-stream, CO conversion decreased on CuCoLa 2 O 3 while methanol and higher alcohol selectivity increased. The behaviors on CuCoZrO 2 and CuCoAl 2 O 3 were different. On these two catalysts, CO conversion and selectivity reached a near-steady state much more quickly than CuCoLa 2 O 3 . These results suggest changes on CuCoLa 2 O 3 that increase the selectivity for oxygenates continue with time, at least over the time scale investigated here.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Aerobic oxidative coupling of amines to imines by mesoporous copper aluminum mixed metal oxides via generation of Reactive Oxygen Species (ROS)

We report a mesoporous, monomodal copper aluminum mixed metal oxide (MMO) (average pore size 9.63 nm, surface area 140 m 2 /g) synthesized via a modified inverse micelle method, efficiently catalyzes aerobic oxidative coupling of amines to imines. This material exhibits excellent conversion (> 99%) and selectivity (> 99%) towards imine synthesis under mild, solvent free, green conditions utilizing atmospheric air as the sole oxidant. Catalytic activity is observed for a diverse range of amine substrates. The aerobic oxidation of amines to imines follows a unique mechanistic pathway which involves Reactive Oxygen Species (ROS).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Laser-induced digital oxidation for copper-based flexible photodetectors

Copper oxide compounds (Cu x O) with bandgaps of 1.3–2.1 eV (CuO) and 2.1–2.6 eV (Cu 2 O) have been investigated as promising p-type semiconducting materials. Cu x O is generally obtained by deposition or thermal oxidation, but those methods are not optimal for flexible substrates. Furthermore, additional patterning steps are required to fabricate devices. In this work, we present an easy, controllable method to fabricate a metal-semiconductor-metal (MSM) photodetector using laser-induced oxidation of a thin Cu film. After laser irradiation, the Cu film is heated under ambient conditions, and this leads to a thermal oxidation reaction, in which Cu oxide is monolithically formed in the Cu film and a Cu-Cu x O-Cu MSM structure is produced. Since the laser offers localized heating, an arbitrary CuxO pattern can be written in the Cu film by spatially controlled heating. In addition, by optimizing the heating time, the laser-induced oxidation can be successfully performed even on a flexible substrate. To study the laser-induced oxidation, we examined the correlation between laser parameters and the oxidation pattern and analyzed the composition using scanning electron microscopy, Raman spectroscopy, and X-ray photoemission spectroscopy. Furthermore, we measured the transient photoresponse and employed scanning photocurrent microscopy to investigate the mechanism of carrier transport behavior.

36 MATERIALS SCIENCE↗

Characterization of Virgin, Re-used, and Oxygen-reduced Copper Powders processed by the Plasma Spheroidization Process

We report that fabrication of parts with high mechanical properties heavily depend on the quality of powder deployed in the fabrication process. Copper powder in three different powder types were spheroidized using radio-frequency inductively coupled plasma (ICP) spheroidization process (TekSphero-15 system). The characterized powders include virgin powder as purchased from the powder manufacturer, powder used in electron beam powder bed fusion (EB-PBF) process, and reconditioned powder, which was used powder that underwent an oxygen-reduction treatment. The goal of spheroidizing these powder types was to evaluate the change in powder morphology, the possibility of enhancing the powder properties back to their as-received conditions, and assess oxygen reduction of the powder lots given their initial oxygen contents. Also, to investigate the impact of re-spheroidization on powder properties, the second round of spheroidization was performed on the already used-spheroidized powder. The impact of powder type on powder sphericity and particle size distribution was evaluated using the image analysis of scanning electron microscope (SEM) micrographs and laser diffraction, respectively. The spheroidized powder showed higher sphericity and more uniform particle size distribution overall. Depending on the powder collection bin, second round of spheroidization affected the powder sphericity differently. The possibility of deploying the plasma spheroidization process as an alternative oxygen-reduction technique was also investigated through tracking the powders’ oxygen content using inert gas fusion method before and after the spheroidization. The plasma spheroidized powder showed less oxygen content than the hydrogen-treated powder. The second round of spheroidization caused no change in oxygen content. The correlation between oxygen-reduction and created cracks was discussed and compared between plasma spheroidization and hydrogen-treatment. The plasma spheroidization process created a powder with higher sphericity, uniform particle size, and less oxygen content.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗