Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Characteristics of isopentanol as a fuel for HCCI engines.

Long chain alcohols possess major advantages over the currently used ethanol as bio-components for gasoline, including higher energy content, better engine compatibility, and less water solubility. The rapid developments in biofuel technology have made it possible to produce C{sub 4}-C{sub 5} alcohols cost effectively. These higher alcohols could significantly expand the biofuel content and potentially substitute ethanol in future gasoline mixtures. This study characterizes some fundamental properties of a C{sub 5} alcohol, isopentanol, as a fuel for HCCI engines. Wide ranges of engine speed, intake temperature, intake pressure, and equivalence ratio are investigated. Results are presented in comparison with gasoline or ethanol data previously reported. For a given combustion phasing, isopentanol requires lower intake temperatures than gasoline or ethanol at all tested speeds, indicating a higher HCCI reactivity. Similar to ethanol but unlike gasoline, isopentanol does not show two-stage ignition even at very low engine speed (350 rpm) or with considerable intake pressure boost (200 kPa abs.). However, isopentanol does show considerable intermediate temperature heat release (ITHR) that is comparable to gasoline. Our previous work has found that ITHR is critical for maintaining combustion stability at the retarded combustion phasings required to achieve high loads without knock. The stronger ITHR causes the combustion phasing of isopentanol to be less sensitive to intake temperature variations than ethanol. With the capability to retard combustion phasing, a maximum IMEP{sub g} of 5.4 and 11.6 bar was achieved with isopentanol at 100 and 200 kPa intake pressure, respectively. These loads are even slightly higher than those achieved with gasoline. The ITHR of isopentanol depends on operating conditions and is enhanced by simultaneously increasing pressures and reducing temperatures. However, increasing the temperature seems to have little effect on ITHR at atmospheric pressure, but it does promote hot ignition. Finally, the dependence of ignition timing on equivalence ratio, here called {phi}-sensitivity, is measured at atmospheric intake pressure, showing that the ignition of isopentanol is nearly insensitive to equivalence ratio when thermal effects are removed. This suggests that partial fuel stratification, which has been found effective to control the HRR with two-stage ignition fuels, may not work well with isopentanol at these conditions. Overall, these results indicate that isopentanol has a good potential as a HCCI fuel, either in neat form or in blend with gasoline.

02 PETROLEUM↗

Enhanced ionic conductivity in oxide heterostructures

Fuel cells are electrochemical devices used to generate energy out of hydrogen. In a fuel cell, two conducting electrodes are separated by an electrolyte that is permeable to ions (either hydrogen or oxygen, depending on the fuel-cell category) but not to electrons. An electrode catalytic process yields the ionic species, which are transported through the electrolyte, while electrons blocked by the electrolyte pass through the external circuit. Polymeric membrane (PEMFC) or phosphoric acid fuel cells (PAFC) operating at low temperatures are the preferred option for transportation because of their quite large efficiencies (50%), compared with gasoline combustion engines (25%). Other uses are also being considered, such as battery replacements for personal electronics and stationary or portable emergency power. Solid-oxide fuel cells (SOFCs), operating at high temperatures, are a better option for stationary power generation because of their scalability. Here O{sup 2-} ions are the mobile species that travel at elevated temperatures (800-1000 C) through a solid electrolyte material to react with H{sup +} ions in the anode to produce water (Fig. 1). The high operating temperatures of solid oxide fuel cells are a major impediment to their widespread use in power generation. Thus, reducing this operating temperature is currently a major materials research goal, involving the search for novel electrolytes as well as active catalysts for electrode kinetics (oxygen reduction and hydrogen oxidation). Among oxide-ion conductors, those of anion-deficient fluorite structures such as yttria-stabilized zirconia (YSZ), xY{sub 2}O{sub 3}:(1-x) ZrO{sub 2}, are extensively used as electrolytes in SOFCs. Doping with Y{sub 2}O{sub 3} is known to stabilize the cubic fluorite structure of ZrO{sub 2} and to supply the oxygen vacancies responsible for the ionic conduction. These materials are characterized by a large number of mobile oxygen vacancies, which are randomly distributed in the structure, and thus give rise to a completely disordered anion (oxygen) sublattice. Traditionally, the main strategy to reduce the operating temperature has been to search for novel electrolyte materials with larger oxide-ion conductivity values. Only recently has the use of artificial nanostructures appeared as a promising new direction for dramatically improved properties.

02 PETROLEUM↗

Preparation and Characterization of Nanocopper Ferrite and Its Green Catalytic Activity in Alcohol Oxidation Reaction

A new type of magnetic material copper ferrite (CuFe{sub 2}O{sub 4}) is successfully manufactured through microwave combustion method. Starch has been tested as a single fuel in this combustion-based synthesis of copper ferrite by using different fuel compositions and equivalence ratios (fuel/oxidant). The formed copper ferrite is characterized by X-ray diffraction analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. Magnetic properties of the prepared copper ferrite are analyzed by vibrating sample magnetometer (VSM). Surface area is measured by the nitrogen adsorption/desorption isotherms. A detailed examination of the morphology of the material in various microwave method-catalyzed processes shows that they provide an optimum catalytic activity due to a combination of lower crystal size and higher activity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effects of multi-component diffusion and heat release on laminar diffusion flame liftoff

Numerical simulations were conducted of the liftoff and stabilization phenomena of laminar jet diffusion flames of inert-diluted C{sub 3}H{sub 8} and CH{sub 4} fuels. Both non-reacting and reacting jets were investigated, including multi-component diffusivities and heat release effects (buoyancy and gas expansion). The role of Schmidt number for non-reacting jets was investigated, with no conclusive Schmidt number criterion for liftoff previously arrived at in similarity solutions. The cold-flow simulation for He-diluted CH{sub 4} fuel does not predict flame liftoff; however, adding heat release reaction lead to the prediction of liftoff, which is consistent with experimental observations. Including reaction was also found to improve liftoff height prediction for C{sub 3}H{sub 8} flames, with the flame base location differing from that in the similarity solution - the intersection of the stoichiometric and iso-velocity (equal to 1-D flame speed) is not necessary for flame stabilization (and thus liftoff). Possible mechanisms other than that proposed for similarity solution may better help to explain the stabilization and liftoff phenomena. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Survey Of CO{sub 2} Laser Ablation Propulsion With Polyoxymethylene Propellant

Polyoxymethylene (POM) has been widely studied as a laser propulsion propellant paired to CO{sub 2} laser radiation. POM is a good test case for studying ablation properties of polymer materials, and within limits, for study of general trends in laser ablation-induced impulse. Despite many studies, there is no general understanding of POM ablation that takes into account the ambient pressure, spot area, fluence, and effects from confinement and combustion. This paper reviews and synthesizes CO{sub 2} laser ablation propulsion research using POM targets. Necessary directions for future study are indicated to address incomplete regions of the various parameter spaces. Literature data is compared in terms of propulsion parameters such as momentum coupling coefficient and specific impulse, within a range of fluences from about 1-500 J/cm{sup 2}, ambient pressures from about 10{sup -2}-10{sup 5} Pa, and laser spot areas from about 0.01-10 cm{sup 2}.

42 ENGINEERING↗

Magnetic Studies of Mutiferroic Bi{sub 1-x}La{sub x}FeO{sub 3} Ceramics Synthesized By Solution Combustion Technique

Bi{sub 1-x}La{sub x}FeO{sub 3} (x = 0.0, 0.05, 0.10, 0.15) ceramic samples were prepared by solution combustion technique. X-ray diffraction patterns confirmed the formation of perovskite structured Bi{sub 1-x}La{sub x}FeO{sub 3} phase. Saturation magnetization (M{sub s}) increases with increasing La concentration from x = 0.0 to x = 0.15. Weak ferromagnetism is observed at room temperature in all the doped and undoped BFO samples. Mossbauer spectroscopy confirmed the presence of single-phase material for the doped compositions. Improvement in magnetic behavior appears to arise from a combination of the propensity of the samples to form pure phase material, partial destruction of spin cycloids and increased canting of spins.

36 MATERIALS SCIENCE↗

Structure, magnetic and complex impedance analysis of (1-x)BaTiO{sub 3}- xMgFe{sub 2}O{sub 4} composite

MgFe{sub 2}O{sub 4} was synthesized by using sol-gel auto-combustion technique and coupled with BaTiO{sub 3} using the conventional solid state reaction method with different weight fraction of x = 0.00, 0.02, 0.04, 0.06 and 0.08 to form (1-x)BaTiO{sub 3} - xMgFe{sub 2}O{sub 4} composite. The structure, magnetic properties and complex impedance analysis of the composite samples were studied using X-ray diffraction technique (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM) and High-frequency response analyzer (HFRA) respectively. XRD patterns showed a single phase tetragonal BaTiO{sub 3} for each composition due to the very small amount of MgFe{sub 2}O{sub 4}. The hysteresis loop confirmed that the composite has soft magnetic properties by addition of MgFe{sub 2}O{sub 4}. Small coercive field, HC has been recorded and it decreased with the increasing of MgFe{sub 2}O{sub 4} weight fraction. However, magnetization increased when the amount of MgFe{sub 2}O{sub 4} is increased. Impedance analysis conducted in range of 0.1 Hz to 10 MHz showed two depressed semicircle arcs for samples with MgFe{sub 2}O{sub 4} due to the resistive and capacitive behavior of the bulk and grain boundaries of the samples.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Computational and experimental study of laminar flames

During the past three years, our research has centered on an investigation of the effects of complex chemistry and detailed transport on the structure and extinction of hydrocarbon flames in coflowing axisymmetric configurations. We have pursued both computational and experimental aspects of the research in parallel on both steady-state and time-dependent systems. The computational work has focused on the application of accurate and efficient numerical methods for the solution of the steady-state and time-dependent boundary value problems describing the various reacting systems. Detailed experimental measurements were performed on axisymmetric coflow flames using two-dimensional imaging techniques. Previously, spontaneous Raman scattering, chemiluminescence, and laser-induced fluorescence were used to measure the temperature, major and minor species profiles. Particle image velocimetry (PIV) has been used to investigate velocity distributions and for calibration of time-varying flames. Laser-induced incandescence (LII) with an extinction calibration was used to determine soot volume fractions, while soot surface temperatures were measured with three-color optical pyrometry using a color digital camera. A blackbody calibration of the camera allows for determination of soot volume fraction as well, which can be compared with the LII measurements. More recently, we have concentrated on a detailed characterization of soot using a variety of techniques including time-resolved LII (TiRe-LII) for soot primary particles sizes, multi-angle light scattering (MALS) for soot radius of gyration, and spectrally-resolved line of sight attenuation (spec-LOSA). Combining the information from all of these soot measurements can be used to determine the soot optical properties, which are observed to vary significantly depending on spatial location and fuel dilution. Our goal has been to obtain a more fundamental understanding of the important fluid dynamic and chemical interactions in these flames so that this information can be used effectively in combustion modeling.

02 PETROLEUM↗

Diode laser absorption sensors for gas-dynamic and combustion flows

Recent advances in room-temperature, near-IR and visible diode laser sources for tele-communication, high-speed computer networks, and optical data storage applications are enabling a new generation of gas-dynamic and combustion-flow sensors based on laser absorption spectroscopy. In addition to conventional species concentration and density measurements, spectroscopic techniques for temperature, velocity, pressure and mass flux have been demonstrated in laboratory, industrial and technical flows. Combined with fibreoptic distribution networks and ultrasensitive detection strategies, compact and portable sensors are now appearing for a variety of applications. In many cases, the superior spectroscopic quality of the new laser sources compared with earlier cryogenic, mid-IR devices is allowing increased sensitivity of trace species measurements, high-precision spectroscopy of major gas constituents, and stable, autonomous measurement systems. The purpose of this article is to review recent progress in this field and suggest likely directions for future research and development. The various laser-source technologies are briefly reviewed as they relate to sensor applications. Basic theory for laser absorption measurements of gas-dynamic properties is reviewed and special detection strategies for the weak near-IR and visible absorption spectra are described. Typical sensor configurations are described and compared for various application scenarios, ranging from laboratory research to automated field and airborne packages. Recent applications of gas-dynamic sensors for air flows and fluxes of trace atmospheric species are presented. Applications of gas-dynamic and combustion sensors to research and development of high-speed flows aeropropulsion engines, and combustion emissions monitoring are presented in detail, along with emerging flow control systems based on these new sensors. Finally, technology in nonlinear frequency conversion, UV laser materials, room-temperature mid-IR materials and broadly tunable multisection devices is reviewed to suggest new sensor possibilities.

Non-NASA Center↗

Influence of the synthesis method on the porosity, microstructure and electrical properties of La{sub 0.7}Sr{sub 0.3}MnO{sub 3} cathode materials

Lanthanum strontium manganite (La{sub 1-x}Sr{sub x}MnO{sub 3}, LSM) has been studied as a promising material for application as a cathode in solid oxide fuel cells. In the present work La{sub 0.7}Sr{sub 0.3}MnO{sub 3} nanopowders were synthesized by three different methods (combustion, citrate and solid-state) and characterized by thermal analysis, X-ray diffraction, physical adsorption of N{sub 2} and scanning electron microscopy. All powders exhibited single LSM phase formation with crystallite sizes in the range of 12-20 nm. Nanopowders were sintered at 1100 deg. C to produce porous pellets. The porosity, particle size and microstructure of LSM sintered bodies are strongly dependent on the preparation methodology. The samples synthesized by combustion and citrate methods presented smaller particle sizes and higher porosity after sintering than that derived from solid-state synthesis. However, the electrical conductivity, measured by two-probe technique, was very similar for all three samples.

36 MATERIALS SCIENCE↗

A Bayesian approach to calibrating hydrogen flame kinetics using many experiments and parameters

First-principles Markov Chain Monte Carlo sampling is used to investigate uncertainty quantification and uncertainty propagation in parameters describing hydrogen kinetics. Specifically, we sample the posterior distribution for thirty-one parameters focusing on the H 2 O 2 and HO 2 reactions resulting from conditioning on ninety-one experiments. Established literature values are used for the remaining parameters in the mechanism as well as other thermodynamic and transport data needed to specify fluid properties. The samples are computed using an affine invariant sampler starting with broad, noninformative priors. Autocorrelation analysis shows that O(1M) samples are sufficient to obtain a reasonable sampling of the posterior. The resulting distribution identifies strong positive and negative correlations and several non-Gaussian characteristics. Using samples drawn from the posterior, we investigate the impact of parameter uncertainty on the prediction of two more complex flames: a 2D premixed flame kernel and the ignition of a hydrogen jet issuing into a heated chamber. The former represents a combustion regime similar to the target experiments used to calibrate the mechanism and the latter represents a different combustion regime. For the premixed flame, the net amount of product after a given time interval has a standard deviation of less than 2% whereas the standard deviation of the ignition time for the jet is more than 10%. The samples used for these studies are posted online. These results indicate the degree to which parameters consistent with the target experiments constrain predicted behavior in different combustion regimes. Finally, this process provides a framework for both identifying reactions for further study from candidate mechanisms as well as combining uncertainty quantification and propagation to, ultimately, tie uncertainty in laboratory flame experiments to uncertainty in end-use numerical predictions of more complicated scenarios.

97 MATHEMATICS AND COMPUTING↗

Replication of engine block cylinder bridge microstructure and mechanical properties with lab scale 319 Al alloy billet castings

In recent years, aluminum alloy gasoline engine blocks have in large part successfully replaced nodular cast iron engine blocks, resulting in improved vehicle fuel efficiency. However, because of the inadequate wear resistance properties of hypoeutectic Al–Si alloys, gray iron cylinder liners are required. These liners cause the development of large tensile residual stress along the cylinder bores and necessitate the maximization of mechanical properties in this region to prevent premature engine failure. The aim of this study was to replicate the engine cylinder bridge microstructure and mechanical properties following TSR treatment (which removes the sand binder to enable easy casting retrieval) using lab scale billet castings of the same alloy composition with varying cooling rates. Comparisons in microstructure between the engine block and the billet castings were carried out using optical and scanning electron microscopy, while mechanical properties were assessed using tensile testing. The results suggest that the microstructure at the top and middle of the engine block cylinder bridge was successfully replicated by the billet castings. However, the microstructure at the bottom of the cylinder was not completely replicated due to variations in secondary phase morphology and distribution. The successful replication of engine block microstructure will enable the future optimization of heat treatment parameters. - Highlights: • A method to replicate engine block microstructure was developed. • Billet castings will allow cost effective optimization of heat treatment process. • The replication of microstructure in the cylinder region was mostly successful. • Porosity was more clustered in the billet castings compared to the engine block. • Mechanical properties were lower in billet castings due to porosity and inclusions.

36 MATERIALS SCIENCE↗

Structural, morphological and optical investigations on BaMgAl{sub 10}O{sub 17}:Eu{sup 2+} elaborated by a microwave induced solution combustion synthesis

Graphical abstract: Graphical abstract (with Research highlights). This is a paragraph for graphical abstract. Research highlights: {yields} Synthesis of BAM:Eu{sup 2+} by MISCS using different fuel to oxidizer molar ratios. {yields} Both blue and red phosphors were obtained. {yields} Majority of blue phosphors was obtained for fuel-rich synthesis. {yields} A specific morphology was observed for each contribution. -- Abstract: Blue-emitting Eu{sup 2+}-doped barium magnesium aluminate (BaMgAl{sub 10}O{sub 17}:Eu{sup 2+}) for advanced displays and lighting devices was prepared by a microwave induced solution combustion synthesis using urea as combustion fuel and nitrates as oxidizer. Purity control of as-synthesized blue phosphor particles was undertaken by modifying the fuel to oxidizer molar ratio. X-ray diffraction, scanning electron microscopy and photoluminescence were used to investigate powders crystallinity, particles size, morphology and luminescent properties, respectively. Fuel-rich urea reactions preferentially lead to pure phases compared to the powders synthesized with a stoichiometric fuel to oxidizer ratio. In both cases, we produce a nearly pure well-crystallized and nanostructured BaMgAl{sub 10}O{sub 17}:Eu{sup 2+}. Photoluminescence measurements exhibit the characteristic blue emission of Eu{sup 2+} under UV light excitation however a weak red emission associated to Eu{sup 3+} is also detected.

36 MATERIALS SCIENCE↗

Exploitation of Unique Properties of Zeolites in the Development of Gas Sensors

The unique properties of microporous zeolites, including ion-exchange properties, adsorption, molecular sieving, catalysis, conductivity have been exploited in improving the performance of gas sensors. Zeolites have been employed as physical and chemical filters to improve the sensitivity and selectivity of gas sensors. In addition, direct interaction of gas molecules with the extraframework cations in the nanoconfined space of zeolites has been explored as a basis for developing new impedance-type gas/vapor sensors. In this review, we summarize how these properties of zeolites have been used to develop new sensing paradigms. There is a considerable breadth of transduction processes that have been used for zeolite incorporated sensors, including frequency measurements, optical and the entire gamut of electrochemical measurements. It is clear from the published literature that zeolites provide a route to enhance sensor performance, and it is expected that commercial manifestation of some of the approaches discussed here will take place. The future of zeolite-based sensors will continue to exploit its unique properties and use of other microporous frameworks, including metal organic frameworks. Zeolite composites with electronic materials, including metals will lead to new paradigms in sensing. Use of nano-sized zeolite crystals and zeolite membranes will enhance sensor properties and make possible new routes of miniaturized sensors.

36 MATERIALS SCIENCE↗

Preliminary studies of combustor sensitivity to alternative fuels

Combustion problems associated with using alternative fuels ground power and aeropropulsion applications were studied. Rectangular sections designed to simulate large annular combustor test conditions were examined. The effects of using alternative fuels with reduced hydrogen content, increased aromatic content, and a broad variation in fuel property characteristics were also studied. Data of special interest were collected which include: flame radiation characteristics in the various combustor zones; the correponding increase in liner temperature from increased radiant heat flux; the effect of fuel bound nitrogen on oxides of nitrogen (NO sub x) emissions; and the overall total effect of fuel variations on exhaust emissions.

Humenik, F. M.↗

Feasibility Study of SSTO Base Heating Simulation in Pulsed-Type Facilities

A laboratory simulation of the base heating environment of the proposed reusable Single-Stage-To-Orbit vehicle during its ascent flight was proposed. The rocket engine produces CO2 and H2, which are the main combustible components of the exhaust effluent. The burning of these species, known as afterburning, enhances the base region gas temperature as well as the base heating. To determine the heat flux on the SSTO vehicle, current simulation focuses on the thermochemistry of the afterburning, thermophysical properties of the base region gas, and ensuing radiation from the gas. By extrapolating from the Saturn flight data, the Damkohler number for the afterburning of SSTO vehicle is estimated to be of the order of 10. The limitations on the material strengths limit the laboratory simulation of the flight Damkohler number as well as other flow parameters. A plan is presented in impulse facilities using miniature rocket engines which generate the simulated rocket plume by electric ally-heating a H2/CO2 mixture.

Park, Chung Sik↗

Performance Evaluation of AG-1 FC HEPA Filters and Medium in Nuclear Complex Facilities - 20434

High Efficiency Particulate Air (HEPA) filters are credited as the final barrier against the release of radioactive aerosol contamination in nearly every operating U. S. Department of Energy (DOE) and National Nuclear Security Agency (NNSA) nuclear facility. The Institute for Clean Energy Technology (ICET) at Mississippi State University maintains a research program that studies various aspects of these components of containment systems and seeks to answer key questions from across the industry. This programmatic overview will include results from recent and ongoing studies, including a study on filter design and performance envelope, degradation due to aging or fatigue, fire event impact on HEPA filters, and accelerated aging of medium and component parts. ICET has completed a study helping to define the threshold for combined elevated temperature and relative humidity resistance of separator style and separator-less style HEPA filters that are used in DOE complexes. The study provides experimental data that considers elevated temperature, elevated relative humidity (RH), and target differential pressure (dP) in an attempt to gain a better understanding or more comprehensive insight into the operating envelope of different configurations of ASME (American Society for Mechanical Engineers) AG-1 Section FC filters. Test variables including air temperature ranges of 48.88 deg. C, 54.44 deg. C, or 60 deg. C (120, 130, or 140 deg. F); air RH ranges including 60-70%, 80%, or 90+% with initial filter dP of either 497.68 Pa, 746.52 Pa, or 995.36 Pa (2 inches water column (in. w. c.), 3 in. w. c., or 4 in. w. c.) included for full bracketing of each set of conditions. A study examining the effects of aging and fatigue on nuclear grade HEPA filters and medium elucidates the physical properties of media along with testing of new and aged ASME AG-1 HEPA filters. In addition to performing autopsies of the tested, aged filters to help better understand the service life of their performance, newly designed accelerated aging chambers allow new medium to undergo accelerated aging and exposure treatments. Evaluation of degradation in physical properties and functionality requires a high population of aged filters of different ages, designs, manufacturers, and operational histories. The limited availability of this population and the impropriety of looking solely at formulations and components from past years requires experimental design that will provide foresight into future filter performance. This undertaking therefore involves not only properties analysis of aged medium from different operational histories, ages, designs, and manufacturers, but also prescience in analytical goals via accelerated aging studies of newly manufactured media. A more complete understanding of the mechanisms of degradation from past formulations as well as current and future formulations is possible. Accelerated Aging of newly manufactured media utilizes exposure treatments based on the Arrhenius equation to artificially age medium and therefore glimpse into the future. Evaluation of current media properties This testing allows for the comparison of performance and durability of new filters under upset or design basis conditions with aged filters that were in service under ambient conditions and other aged filters retained in storage. Susceptibility of HEPA filters to the effects of combustion byproducts, heat, and water is also being studied in an attempt to gain understanding on the prevention of filter failures during fire events in nuclear facilities. ICET seeks to determine the effect of filter performance due to smoke loading using characterized smoke from variable fuel compositions, geometries, and loads; the smoke capacity of various filters with different burning conditions, heat release rates and transport, as well as mass transport from the air stream will be studied in low flow containment systems. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Microwave-assisted pyrolysis of hydrocarbons using iron-based alumina catalysts obtained via solution combustion synthesis

The demand for hydrogen is growing which makes the development of clean and efficient H2 synthesis technologies imperative. Microwave-assisted, thermocatalytic, dehydrogenation of hydrocarbons has demonstrated the ability to generate H2 with high yield and selectivity, leaving behind valuable solid carbon byproducts. However, this microwave-assisted process is unoptimized which prevents it from being utilized in industry. A critical component of optimization is the development of a catalyst that is catalytically active, a good microwave absorber, and can be regenerated for repeated dehydrogenation cycles. Previous studies that focused on plastic waste decomposition have used iron-based alumina (FeAlxOy) made via solution combustion synthesis (SCS). Unexplored is the effect of tuning SCS parameters on dehydrogenation performance, the use of these materials in hydrocarbon decomposition to H2, and the regeneration of these catalysts. This dissertation has three objectives: (1) characterize the relationship between SCS parameters and the material properties of FeAlxOy, (2) determine how differences in the material properties of FeAlxOy influence their performance as catalysts during microwave-assisted pyrolysis of fossil fuels, and (3) investigate the Boudouard reaction to regenerate the FeAlxOy post-dehydrogenation.

Chanoi, Zachary Aidan↗