Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “A. Microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Influence of the Si3N4 microstructure on its R-curve and fatigue behavior

The R-curve and fatigue behavior of a silicon nitride with large, highly elongated grains were compared to those of a silicon nitride with smaller, more equiaxed grains. The former was found to have higher toughness and a slightly rising R-curve which enhanced fatigue resistance, while the latter had constant toughness with crack length. The R-curve was attributed to crack deflection and grain pull-out. The microstructure did not influence the dynamic fatigue properties of the two ceramics, as both had good resistance to dynamic fatigue. The cyclic fatigue resistance of the large-grained Si3N4, however, was surprisingly low.

Tikare, Veena↗
NASA NTRS1991

Microstructural and strength stability of CVD SiC fibers in argon environments

The room temperature tensile strength and microstructure of three types of commercially available chemically vapor deposited silicon carbide fibers were measured after 1, 10, and 100 hour heat treatments under argon pressures of 0.1 to 310 MPa at temperatures to 2100 C. Two types of fiber had carbon-rich surface coatings and the other contained no coating. All three fiber types showed strength degradation beyond 1400 C. Time and temperature of exposure had greater influence on strength degradation than argon pressure. Recrystallization and growth of near stoichiometric SiC grains appears to be the dominant mechanism for the strength degradation.

Bhatt, Ramakrishna T.↗
NASA NTRS1992

Tribological and microstructural comparison of HIPped PM212 and PM212/Au self-lubricating composites

The feasibility of replacing the silver with the volumetric equivalent of gold in the chromium carbide-based self-lubricating composite PM212 (70 wt. percent NiCo-Cr3C2, 15 percent BaF2/CaF2 eutectic) was studied. The new composite, PM212/Au has the following composition: 62 wt. percent NiCo-Cr3C2, 25 percent Au, 13 percent BaF2/CaF2 eutectic. The silver was replaced with gold to minimize the potential reactivity of the composite with possible environmental contaminants such as sulfur. The composites were fabricated by hot isostatic pressing (HIPping) and machined into pin specimens. The pins were slid against nickel-based superalloy disks. Sliding velocities ranged from 0.27 to 10.0 m/s and temperatures from 25 to 900 C. Friction coefficients ranged from 0.25 to 0.40 and wear factors for the pin and disk were typically low 10(exp -5) cu mm/N-m. HIPped PM212 measured fully dense, whereas PM212/Au had 15 percent residual porosity. Examination of the microstructures with optical and scanning electron microscopy revealed the presence of pores in PM212/Au that were not present in PM212. Though the exact reason for the residual porosity in PM212/Au was not determined, it may be due to particle morphology differences between the gold and silver and their effect on powder metallurgy processing.

Bogdanski, Michael S.↗
NASA NTRS1990

Rheological Behavior and Microstructure of Ceramic Particulate/Aluminum Alloy Composites

The rheological behavior and microstructure were investigated using a concentric cylinder viscometer for three different slurries: semi-solid alloy slurries of a matrix alloy, Al-6.5wt percent Si: composite slurries, SiC (sub p) (8.5 microns)/Al-6.5wt percent Si, with the same matrix alloy in the molten state, and composite slurries of the same composition with the matrix alloy in the semi-solid state. The pseudoplasticity of these slurries was obtained by step changes of the shear rate from a given initial shear rate. To study the thixotropic behavior of the system, a slurry was allowed to rest for different periods of time, prior to shearing at a given initial shear rate. In the continuous cooling experiments, the viscosities of these slurries were dependent on the shear rate, cooling rate, volume fraction of the primary solid of the matrix alloy, and volume fraction of silicon carbide. In the isothermal experiments, all three kinds of slurries exhibited non-Newtonian behavior, depending on the volume fraction of solid particles.

Moon, Hee-Kyung↗
NASA NTRS1991

The effect of copper, chromium, and zirconium on the microstructure and mechanical properties of Al-Zn-Mg-Cu alloys

The present study evaluates the effect of the systematic variation of copper, chromium, and zirconium contents on the microstructure and mechanical properties of a 7000-type aluminum alloy. Fracture toughness and tensile properties are evaluated for each alloy in both the peak aging, T8, and the overaging, T73, conditions. Results show that dimpled rupture essentially characterize the fracture process in these alloys. In the T8 condition, a significant loss of toughness is observed for alloys containing 2.5 pct Cu due to the increase in the quantity of Al-Cu-Mg-rich S-phase particles. An examination of T8 alloys at constant Cu levels shows that Zr-bearing alloys exhibit higher strength and toughness than the Cr-bearing alloys. In the T73 condition, Cr-bearing alloys are inherently tougher than Zr-bearing alloys. A void nucleation and growth mechanism accounts for the loss of toughness in these alloys with increasing copper content.

Wagner, John A.↗
NASA NTRS1991

Microstructural and magnetic characterization of rapidly solidified and annealed Pt-Co-B alloys

Significant increases in intrinsic coercivity (Hic) of Pt-Co alloys have been obtained by the addition of boron and the application of rapid solidification processing. After rapid solidification by double anvil splat quenching with subsequent annealing at 650 C for 30 min, an alloy of Pt42Co45B13 exhibits an Hic as high as 14 kOe. Annealing of the Pt-Co-B influences the L1(0) superlattice structure and grain size of the matrix, the crystal structure and size of Co-boride precipitate, and the distribution of magnetic domain walls. A microstructural analysis shows that the maximum H(ic) occurs when Co borides, having the Co3B structure, are within the single magnetic domain size. The magnetic hardening mechanism in Pt-Co-B is believed to be a combination of inhibited magnetic domain nucleation and difficult reverse magnetic domain growth caused by the interaction of the magnetically anisotropic Co borides with the L1(0) Pt-Co matrix.

Qiu, N.↗
NASA NTRS1992

Sintering time and atmosphere influences on the microstructure and mechanical properties of tungsten heavy alloys

The present paper traces the microstructure and mechanical property variations vs sintering time under conditions where the atmosphere was adjusted to suppress pore generation. Attention is given to tracing the mechanical property links to the grain size under optimized sintering conditions. The optimal cycle is used to sinter two heavy alloy compositions (88 and 95 wt pct W) for times up to 600 minutes at 1480 C. The 88-pct-W samples slumped, but the 95-pct-W samples were fully densified and suitable for tensile testing. At long sintering times, the tungsten grains flattened and the tungsten contiguity decreased, indicating a transition to low-energy configurations for the solid-liquid interfaces. The cube of the mean grain size varied linearly with the isothermal sintering time. This allowed the determination of grain size effects on mechanical properties, showing a decreasing yield strength with increasing time in agreement with the Hall-Petch behavior. The tensile strength and elongation were highest for sintering times from 30 to 90 min, reflecting a minimum in the residual porosity.

German, R. M.↗
NASA NTRS1992

The influence of processing parameters on microstructural development of low-weight-percent primary, pro-eutectic, dendritic alloys during directional solidification

Alloy compositions centering about Sn- 5 to 15 wt pct Al and Pb- 4 to 20 wt pct Cu have been directionally solidified as a function of growth rate and orientation with respect to earth's gravity vector. The effect of these processing variables on macrosegregation is presented, and the consequence of a structural transition from primary columnar to equiaxed dendritic growth is examined. Effects detrimental to microstructure and attributed to density variations are shown to be minimized by a novel processing technique. In view of the ground-based results, some considerations follow regarding what might be gained by solidifying these alloys in a microgravity environment.

Grugel, R. N.↗
NASA NTRS1991

Microstructure and mechanical properties of a single crystal NiAl alloy with Zr or Hf rich G-phase precipitates

The possibility of producing NiAl reinforced with the G-phase (Ni16X6Si7), where X is Zr or Hf, has been investigated. The microstructure of these NiAl alloys have been characterized in the as-cast and annealed conditions. The G-phases are present as fine cuboidal precipitates (10 to 40 nm) and have lattice parameters almost four times that of NiAl. They are coherent with the matrix and fairly resistant to coarsening during annealing heat treatments. Segregation and nonuniform precipitate distribution observed in as-cast materials were eliminated by homogenization at temperatures near 1600 K. Slow cooling from these temperatures resulted in large plate shaped precipitates, denuded zones, and a loss of coherency in some of the large particles. Faster cooling produced a homogeneous fine distribution of cuboidal G-phase particles in the matrix. Preliminary mechanical properties for the Zr-doped alloy are presented and compared to binary single crystal NiAl. The presence of these precipitates appears to have an important strengthening effect at temperatures not less than 1000 K compared to binary NiAl single crystals.

Locci, I. E.↗
NASA NTRS1992

Ultrasonic evaluation of oxygen content, modulus, and microstructure changes in YBa2Cu3O(7-x) occurring during oxidation and reduction

Ultrasonic velocity measurement techniques were used to evaluate the effects of oxidation and reduction on the elastic properties, global microstructure and oxygen content of the YBa2Cu3O(7-x) ceramic superconductor for samples ranging from 70 to 90 pct of theoretical density. Bulk density, velocity, and elastic modulus generally increased with increasing oxygen content upon oxidation, and this behavior was reversible. Velocity image patterns were similar after oxidation and reduction treatments for a 90 pct. dense sample, although the velocity value at any given point on the sample was changed following the treatments. The unchanging pattern correlated with destructive measurements showing that the spatial pore distribution (fraction and size) was not measurably altered after the treatments. Changes in superconducting behavior, crystal structure, and grain structure were observed consistent with changes in oxygen content.

Roth, Don J.↗
NASA NTRS1992

Influence of Processing on the Microstructure and Mechanical Properties of a NbAl3-Base Alloy

Induction melting and rapid solidification processing, followed by grinding to 75-micron powder and P/M consolidation, have been used to produce a multiphase, NbAl3-based, oxidation-resistant alloy of Nb-67Al-7Cr-0.5Y-0.25W composition whose strength and ductility are significantly higher than those of the induction-melted alloy at test temperatures of up to 1200 K. Attention is given to the beneficial role of microstructural refinement; the major second phase, AlNbCr, improves both oxidation resistance and mechanical properties.

Hebsur, Mohan G.↗
NASA NTRS1991

Effect of microstructure and composition on the improvement of n-type SiGe/GaP material

Experimental and theoretical work has been conducted at the Jet Propulsion Laboratory to improve the thermoelectric properties of n-type SiGe materials. Particular emphasis has been placed upon the understanding of the differences in dopant solid solubilities when multidoping with both Ga and P instead of P alone, as in standard SiGe alloys. A set of various experimental techniques for obtaining heavily doped hot-pressed samples coupled with thermodynamic theoretical considerations was used to relate microstructure and composition to electrical and thermal transport properties. Application of these results to high-temperature heat treatments of several SiGe/GaP samples achieved substantial improvements of the thermoelectric figure of merit Z, with average values close to 1 x 10-3K-1 over the 600-1000 C temperature range. A set of systematic anneals on heavily doped SiGe/GaP materials is reported in an attempt to consistently reproduce the optimized thermoelectric properties.

Fleurial, Jean-Pierre↗
NASA NTRS1991

Nonlinear mechanics of composite materials with periodic microstructure

This report summarizes the result of research done under NASA NAG3-882 Nonlinear Mechanics of Composites with Periodic Microstructure. The effort involved the development of non-finite element methods to calculate local stresses around fibers in composite materials. The theory was developed and some promising numerical results were obtained. It is expected that when this approach is fully developed, it will provide an important tool for calculating local stresses and averaged constitutive behavior in composites. NASA currently has a major contractual effort (NAS3-24691) to bring the approach developed under this grant to application readiness. The report has three sections. One, the general theory that appeared as a NASA TM, a second section that gives greater details about the theory connecting Greens functions and Fourier series approaches, and a final section shows numerical results.

Jordan, E. H.↗
NASA NTRS1992

Use of cyclic current reversal polarization voltammetry for investigating the relationship between corrosion resistance and heat-treatment induced variations in microstructures of 400 C martensitic stainless steels

Software for running a cyclic current reversal polarization voltammagram has been developed for use with a EG&G Princeton Applied Research Model 273 potentiostat/galvanostat system. The program, which controls the magnitude, direction and duration of an impressed galvanostatic current, will produce data in ASCII spreadsheets (Lotus, Quattro) for graphical representation of CCRPV voltammograms. The program was used to determine differences in corrosion resistance of 440 C martenstic stainless steel produced as a result of changes in microstructure effected by tempering. It was determined that tempering at all temperatures above 400 F resulted in increased polarizability of the material, with the increased likelihood that pitting would be initiated upon exposure to marine environments. These results will be used in development of remedial procedures for lowering the susceptibility of these alloys toward the stress corrosion cracking experienced in bearings used in high pressure oxygen turbopumps used in the main engines of space shuttle orbiters.

Ambrose, John R.↗
NASA NTRS1992

Tribological and microstructural comparison of HIPped PM212 and PM212/Au self-lubricating composites

The feasibility of replacing the silver with the volumetric equivalent of gold in the chromium carbide-based self-lubricating composite PM212 (70 wt percent NiCo-Cr3C2, 15 percent BaF2/CaF2 eutectic) was studied. The new composite, PM212/Au has the following composition: 62 wt percent NiCo-Cr3C2, 25 percent Au, 13 percent BaF2/CaF2 eutectic. The silver was replaced with gold to minimize the potential reactivity of the composite with possible environmental contaminants such as sulfur. The composites were fabricated by hot isostatic pressing (HIPping) and machined into pin specimens. The pins were slid against nickel-based superalloy disks. Sliding velocities ranged from 0.27 to 10.0 m/s and temperatures from 25 to 900 C. Frictions coefficients ranged from 0.25 to 0.40 and wear factors for the pin and disk were typically low 10(exp -5) cu mm/N-m. HIPped PM212 measured fully dense, whereas PM212/Au had 15 percent residual porosity. Examination of the microstructures with optical and scanning electron microscopy revealed the presence of pores in PM212/Au that were not present in PM212. Though the exact reason for the residual porosity PM212/Au was not determined, it may be due to practice morphology differences between the gold and silver and their effect on powder metallurgy processing.

Bogdanski, Michael S.↗
NASA NTRS1992

In situ observations of temperature microstructure above and below the tropopause

The small-scale (less than 1 km) structure of temperature near the tropopause, as indicated by ozone concentration, is examined using data recorded during GALE from the NCAR Sabreliner. A systematic difference is observed in the temperature microstructure of the troposphere and stratosphere in qualitative agreement with evidence from VHF radar observations. Spectral distribution of the temperature variations also differs across the tropopause.

Salathe, Eric P., Jr.↗
NASA NTRS1992

High-temperature deformation and microstructural analysis for silicon nitride-scandium(III) oxide

It was indicated that Si3N4 doped with Sc2O3 may exhibit high temperature mechanical properties superior to Si3N4 systems with various other oxide sintered additives. High temperature deformation of samples was studied by characterizing the microstructures before and after deformation. It was found that elements of the additive, such as Sc and O, exist in small amounts at very thin grain boundary layers and most of them stay in secondary phases at tripple and multiple grain boundary junctions. These secondary phases are devitrified as crystalline Sc2Si2O7. Deformation of the samples was dominated by cavitational processes rather than movements of dislocations. Thus the excellent deformation resistance of the samples at high temperature can be attributed to the very small thickness of the grain boundary layers and the crystalline secondary phase.

Cheong, Deock-Soo↗
NASA NTRS1992

Effect of braze processing on the microstructure and mechanical properties of SCS-6/beta21S titanium matrix composites

An investigation is conducted of the effects of braze processing on the microstructure and tensile properties of SiC fiber-reinforced Ti-15Mo-2.7Nb-3Al-0.25Si-matrix composite (TMC) laminates; the brazing alloy was the commercial Ti-15Cu-15Ni, in both its conventional and metglass forms. Tensile tests conducted at room temperature, 1200 F, and 1500 F showed that the braze processes (1) had little effect on tensile properties, and (2) appeared to degrade neither the reinforcing fibers not the fiber/matrix interfacial bondline.

Hoffman, Eric K.↗