Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “titanium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Metallic Environmentally Resistant Coating Rapid Innovation Initiative

Lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified for space systems to minimize mass while maintaining structural integrity [1,2]. Such alloys however, have poor tribological response (high friction and wear), especially in extreme space environments, which becomes worse with the additional presence of lunar regolith. This leads to short lifetimes and premature failures that will ultimately limit long term operations on the lunar surface [2]. This project is addressing this technology gap by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the life-time and sustainability of both lunar and Martian assets. Ceramics were considered for their high wear resistance, but were rejected because of their low fracture toughness, which would be especially problematic for structural components. The novel and existing coating technologies and deposition methods are being tested in this project. The coating materials are Boron Nitride-Aluminum (BN-Al), Nickle Titanium (NiTi), Aluminum Oxide (AlO3), Ti64 with hBN at 2 and 10 vol percent (Ti-2vol%hBN and Ti-10vol%hBN), and the deposition techniques are high pressure cold-spray (CS) and ambient and vacuum plasma-spray (APS and VPS) [3,4,5]. BN-Al, NiTi, Ti-2vol%hBN, and Ti-10vol%hBN were applied with all three deposition techniques, and AlO3 was applied only using the APS deposition technique. A tungstenite (WS2) film was applied to the NiTi VPS coating. The coating and deposition technique configurations are being tested against several key end-use performance parameters. The parameters include the capabilities of the coatings under wear environments such as regolith simulant, thermal cycling from high (120°C) to cryogenic (-173°C), high vacuum (~10-7 torr), and pre- and post-exposure to ionizing particle radiation. Wear tests include pin on disk, three-body abrasion, and surface erosion by high velocity regolith impacts. The initial down selection is being performed using on virgin and environmental exposure samples using pin on disk and three body abrasion wear tests. From preliminary assessment of this testing, a few configurations were eliminated. Ti-10vol%hBN could not be applied using CS application and NiTi could not be applied using APS or CS application so these configurations did not get tested. Early pin on disk wear tests showed poor wear performance of BN-Al so this coating was eliminated early in the testing process. AlO3 on Al substrate did not survive thermal cycling, but wear testing is continuing for AlO3 on Ti substrate. A more detailed analysis is being con-ducted to further reduce the number of configuration for phase II and III. Phase II testing will include conventionally and additively manufactured substrates with surface erosion testing. In phase III, the coatings will be applied to three mechanism types: channel and slot, ball and socket, and a hinge joint. Each will demonstrate a different type of wear incidence. The mechanisms and their base materials are of direct interest to the end users and infusion points: the Human Landing System (HLS) and the Lunar Surface Innovation Initiative (sustained lunar surface operations). The technology development project is based out of Marshall Space Flight Center, has partnered with Florida International University (Miami, FL) and Plasma Processes (Huntsville, Al), and is supported by a group of NASA mentors from different centers.

dust mitigation↗
DOE OSTI2026

Engineering Na‐Rich P2‐Type Layered Oxides Through Li/Ti Dual Doping for Oxygen Redox Activation and Superior Structural Stability

Sodium layered oxides Na x MO 2 (x ≤ 1 and M = transition metal ions) have gained significant interest as sodium-ion battery (NIB) cathodes owing to their high operating voltages and potential for higher energy density compared with polyanion and Prussian blue–type cathodes. However, their practical applications are often hindered by the irreversible structural transitions leading to capacity fading during cycling. The nature and substitution of transition metal ions define the material properties and electrochemical performance. In this study, through comprehensive electrochemical characterization combined with multi-scale structural and spectroscopical analyses, we demonstrate the synergistic impacts of Lithium and Titanium doping, which not only increases overall capacity by boosting cation and anion cooperative redox contributions but also improves the rate capability and cycling stability. Specifically, Li + doping enhances the available sodium inventory for extraction, while Ti 4+ disrupts Na + /vacancy ordering at lower voltages (< 4 V) and mitigates the detrimental P2→OP4/O2 phase transition during cycling. The combined effect of Lithium and Titanium doping promotes more charge localization on Oxygen, which activates reversible lattice oxygen redox reactions at elevated voltages, contributing additional capacity beyond conventional cationic redox. This work provides crucial insights into the design of high-performance, high-capacity P2-type layered cathode materials for sodium-ion batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In Situ Scattering Studies of Superconducting Vacancy‐Ordered Monoclinic TiO Thin Films

Abstract The structural and transport properties of vacancy‐ordered monoclinic superconducting titanium oxide (TiO) thin films grown by molecular beam epitaxy are investigated. The evolution of the crystal structure during growth is monitored by in situ synchrotron X‐ray diffraction. Long‐range ordering of Ti and O vacancies in the disordered cubic phase stabilizes the vacancy‐ordered monoclinic TiO phase. The reduced structural disorder arising from vacancy‐ordering is correlated with a superconductor‐metal transition (SMT) in contrast to the superconductor‐insulator transition (SIT) observed in cubic TiO, orthorhombic Ti 2 O 3 , and the Magneli γ − Ti 3 O 5 and γ − Ti 4 O 7 phase. Magnetoresistance measurements for the SIT phases indicate superconducting fluctuations persisting in the normal phase. These results confirm the role of disorder related to Ti and O vacancies and structural inhomogeneity in determining the electronic properties of the normal state of titanium oxide‐based superconductors.

Baksi, Merve↗
DOE OSTI2021

Hydrothermal catalysis of waste greases into green gasoline, jet, and diesel biofuels in continuous flow supercritical water

Production of green gasoline, jet, and diesel biofuels from waste greases was achieved using a novel hydrothermal, continuous-flow catalytic process operating under supercritical water conditions, with recycled water the only added chemical. Thermally and chemically stable catalysts were explored to optimize yields of liquid biofuels and to minimize production of gases and acidic compounds. A 50:50 mixture of brown and yellow waste greases converted into 76.6 wt% liquid biocrude (BC); the remainder converted to water and gases. Less than 0.2% of the FS formed carbon char (mainly amongst catalyst particles). Various tubular reactors (Inconel, ® Hastelloy®, titanium, stainless) showed no interior defects, erosion, or mass loss after runs. Here, the titanium catalyst was fully recovered and regenerated back to its original potency. The BC was further refined into 28%, 48%, 20%, and 4 wt%, respectively for green gasoline, jet, diesel, and bunker. Biofuels were analyzed for compound class compositions and reaction mechanisms were proposed. The hundreds of identified fuel products (C3-C35) from processing oleic acid as a pure model compound were identified. The neat green gasoline and diesel biofuels along with a 50% green jet blend (with petroleum Jet A) were tested in appropriate spark ignition, turbine, and diesel engines at University of MN Engine Labs. Biofuels achieved 107.7%, 97.2%, and 101.3% engine power performance levels relative to petroleum fuels (91-Octane, Jet A, #2 Diesel) along with lower CO and pollutant emissions. Biofuels passed ASTM fuel specifications (D4814, D7566, D975) including mandated corrosion and low sulfur limits of all three biofuels.

09 BIOMASS FUELS↗
DOE OSTI2023

Interfacial engineering via laser ablation for high-performing PEM water electrolysis

A rationalized interfacial design strategy was applied to tailor the porous transport layer (PTL)-catalyst layer (CL) contact and the PTL bulk-phase architecture. Particularly, at the PTL-CL interface, our results reveal that laser ablated sintered titanium power-based PTLs improve electrolyzer performance at both the H2NEW Consortium baseline catalyst loading of 0.4 mgIr cm -2 as well as at the ultra-low catalyst loading of 0.055 mgIr cm -2 . Under ultra-low catalyst loadings, the laser ablated PTL demonstrates maximum reduction of 230 mV compared to the commercial PTL at 4 A cm -2 , and reduces by 68 mV at 3.2 A cm -2 under H2NEW baseline loading. Laser ablation alters the titanium phase at the interface, so it forms more uniform structure like a microporous layer or a backing layer, leading to an increase in the surface area in contact with the catalyst layer while preventing the membrane from deforming into the PTL. Moreover, we reveal that bulk-phase architecture modification of the PTL by ablating patterned pores at the flow field-PTL interface improves mass transport without sacrificing contact at the CL-PTL interface. Overall, laser ablation of the PTL is an effective method to customize interfacial design to enhance proton exchange membrane electrolyzer performance.

08 HYDROGEN↗
DOE OSTI2022

Interaction mechanism of transition metal phthalocyanines on transition metal nitride supports

Here, we investigated the electronic interactions between transition metal phthalocyanine (TMPc’s) on a refractory transition metal nitride support, specifically copper phthalocyanine (CuPc) on titanium nitride (TiN). X-ray Photoelectron Spectroscopy (XPS) results suggest a presence of a few nanometer native oxide layer on the surface of the TiN nanoparticles, which consists of TiN, TiO 2 , and Titanium oxynitrides (Ti x O y N z ). A TiNCuPc nanocomposite was synthesized via a simple mixing method due to the strong binding between CuPc and TiN confirmed by density functional theory (DFT) calculations. Both XPS data and DFT calculations revealed an electron transfer from TiN substrate to CuPc molecule. The nature of charge transfer is not influenced by the presence of an oxide layer on the surface of TiN. Substantial deviations are however found between photoelectron emission microscopy (PEEM) measured work function for TiN (4.68 eV) and theoretically calculated work function for pristine stoichiometric TiN (2.63 eV). This behavior is attributed to the presence of an oxide layer on the TiN surface. TiNCuPc composite system has a work function value between those of TiN and CuPc. Our studies open up an opportunity to apply a new class of materials based on transition metal phthalocyanine/transition metal nitride composites to catalysis and optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Solvent effects on the heterogeneous growth of TiO 2 nanostructure arrays by solvothermal synthesis

One-dimensional titanium dioxide (TiO 2 ) nanostructure arrays (nanoarrays) are important metal oxide nanomaterials that can be synthesized via facile solvothermal methods. The properties of the organic solvents can impose significant effects on the microstructures and properties of the final products. However, the discussions were limited to the homogeneously nucleated TiO 2 nanomaterials in free-standing powder form, while the solvent effects are less understood during the heterogeneous growth of TiO 2 nanoarrays on a substrate surface. In this work, six organic compounds, namely 2-butanone, n-decane, n-hexane, toluene, ethylene glycol and ethanol, were selected as the solvents for the solvothermal synthesis of TiO 2 nanoarrays on the cordierite monolithic substrates. Special attentions are paid to the morphology, crystallinity, specific surface area, and porosity of the samples. The heterogeneous growth of TiO 2 nanoarrays on substrate surfaces is found to favor the solvents with moderate dielectric constants, which can be partially dissolved in the aqueous solution and modulate the reaction rate during the solvothermal synthesis. Organic solvents with low dielectric constants may result in a complete separation between the precursors and aqueous solution, and therefore slow down the overall reaction, causing the insufficient growth of the nanoarrays. The TiO 2 nanoarrays are obtained with optimum morphology from the combination of 2-butanone and titanium (IV) butoxide as solvent and precusor, respectively, with a high specific surface area up to 56 m 2 /g including cordierite substrate given a micron thickness. When loaded with Pt catalyst, the TiO 2 nanoarray-based monolithic catalysts show excellent low-temperature catalytic activity and hydrothermal stability for the CO and hydrocarbon oxidation under the simulated exhausted conditions. This article shall shed light on a better understanding of the growth mechanism and rational design of TiO 2 nanoarrays for high-performance catalytic converters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A systematic study of lanthanide titanates (A 2 Ti 2 O 7 ) chemical durability: corrosion mechanisms and control parameters

Dense lanthanide titanates ranging from La 2 Ti 2 O 7 to Yb 2 Ti 2 O 7 were synthesized by spark plasma sintering with similar micro-sized microstructure, and their chemical durability and degradation mechanisms were investigated by semi-dynamic leaching tests. Different corrosion mechanisms from incongruent to congruent dissolution were observed with preferential elemental releases of lanthanides in A 2 Ti 2 O 7 (A = La to Gd) and Ti in Er 2 Ti 2 O 7 and Yb 2 Ti 2 O 7 . Initial leaching was controlled by surface dissolution and long-term dissolution shifted to a diffusion-controlled mechanism for titanate pyrochlores from Sm 2 Ti 2 O 7 to Yb 2 Ti 2 O 7 . Both short-term and long-term leaching rates decreased from La 2 Ti 2 O 7 to Yb 2 Ti 2 O 7 , and materials became more corrosion resistant with decreasing ionic radius ratios of the rare-earth elements and titanium. Amorphous passivation films of several nm-thick enriched with Ti formed on the surfaces of the corroded materials, and the formation mechanisms were governed either by surface reorganization with preferential release of lanthanides or dissolution-precipitation from saturated bulk solutions with preferential release of titanium. Finally, these results demonstrate that the ionic size plays a dominant role in determining chemical durability of lanthanide titanates and a strong correlation is established among chemical composition/structural variation, passivation film formation and corrosion mechanisms, and materials chemical durability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A temperature profile diagnostic for radiation waves on OMEGA-60

Predicting and matching radiation wave propagation with computational models has proven difficult. Information provided by experiments studying radiation flow has been limited when only radiation breakout is measured. We have developed the COAX (co-axial) diagnostic platform to provide spatial temperature profiles of a radiation wave through low density foams as a more detailed constraint for simulations. COAX uses a standard, laser-driven OMEGA-60 halfraum to drive radiation down a titanium-laden silicon oxide foam. Point-projection X-ray absorption spectroscopy perpendicular to the radiation flow measures the spatial profile of titanium ionization. The spectroscopic measurement utilizes a broadband capsule backlighter. Imaging and streak spectroscopy are used to characterize the size and spectrum of this source. Radiography provides an additional constraint by capturing the developing shock as the radiation flow becomes subsonic. The DANTE diagnostic is used to measure the halfraum temperature. Here, we provide a spectroscopic analysis of COAX data to determine temperature, and we describe experimental sources of uncertainty. The temperature is obtained by comparison to multi-temperature synthetic spectra post-processed from radiation-hydrodynamics simulations. Quantitative comparison between data and synthetic spectra generated from temperature profiles at relevant simulation times enable determination of a peak temperature of 114 ± 8 eV at 265 ± 22.4 μm from the halfraum. This represents an improvement over the temperature uncertainties of previous radiation flow experiments. Further refinements to the spectroscopic analysis could achieve ±4 eV. The combination between space-resolved spectroscopy and radiography enables us to determine the distance from the halfraum of both the radiation front and the shock front at the time of measurement. For the example shown in this paper the radiation front position is 600–630 μm at 3.43 ± 0.16 ns and the shock front position is 633 μm at 3.3 ± 0.24 ns.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Variant selection in laser powder bed fusion of non-spherical Ti-6Al-4V powder

The presence of α/α' on prior β/β grain boundaries directly impacts the final mechanical properties of the titanium alloys. The β/β grain boundary variant selection of titanium alloys has been assumed to be unlikely owing to the high cooling rates in laser powder bed fusion (L-PBF). However, we hypothesize that powder characteristics such as morphology (non-spherical) and particle size (50–120 µm) could affect the initial variant selection in L-PBF processed Ti-6Al-4V alloy by locally altering the cooling rates. Despite the high cooling rate found in L-PBF, the results showed the presence of β/β grain boundary α' lath growth inside two adjacent prior β grains. Electron backscatter diffraction micrographs confirmed the presence of β/β grain boundary variant selection, and synchrotron X-ray high-speed imaging observation revealed the role of the “shadowing effect” on the locally decreased cooling rate because of keyhole depth reduction and the consequent β/β grain boundary α' lath growth. The self-accommodation mechanism was the main variant selection driving force, and the most abundant α/α boundary variant was type 4 (63.26°//[ $\bar{10}$ 5 5 $\bar{3}$ ]). The dominance of Category II α lath clusters associated with the type 4 α/α boundary variant was validated using the phenomenological theory of martensite transformations and analytical calculations, from which the stress needed for the β→α' transformation was calculated.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Statistical fracture behavior of doped UO 2 using a ball-on-ring equibiaxial flexure test method

Metal oxide dopants, such as titanium and chromium oxides, have garnered considerable attention for their potential to increase grain size (≥ 30 µm) in UO 2 fuel, purportedly enhancing fission gas retention during reactor operation. Fuel performance is significantly impacted by fuel fracture behavior, so it is important to understand the effects of enhanced grain size and dopant content on UO 2 fuel fracture. UO 2 pellets were doped with 0.1 wt% TiO 2 and 0.3 wt% Cr 2 O 3 to alter density and grain size. Inductively coupled plasma mass spectroscopy measured dopant levels pre- and post-sintering. X-ray diffraction revealed lattice changes and microstrain via Rietveld refinement. Field emission scanning electron microscopy determined grain sizes of approximately 30 µm for TiO 2 doping and 7 µm for Cr 2 O 3 doping. Transverse rupture strength tests were performed on over 30 samples per dataset to obtain characteristic strength and Weibull modulus. Results indicate no statistical difference in fracture strength between 0.1 wt% TiO 2 doped UO 2 and undoped UO 2 , while 0.3 wt% Cr 2 O 3 doped UO 2 exhibited a 20% decrease in fracture strength. Doped UO 2 samples also showed reduced Weibull modulus compared to undoped UO 2 , suggesting increased scatter in fracture strength. This study's findings suggest that titanium and chromium oxide doping in UO 2 , regardless of grain size, induce residual stresses, decreasing fracture strength and increasing variability in fracture behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Mass transport limitations in polymer electrolyte water electrolyzers using spatially-resolved current measurement

Here this work utilizes spatially-resolved current measurements to provide insight into mass transport limitations in electrolyzers that are not observable from traditional polarization measurement. In this study, two types of flow-fields (parallel and triple-serpentine) and two types of diffusion media (patterned porous thin titanium foil LGDLs and Ir-coated titanium felt PTLs) were examined. A non-uniform current distribution dominated by mass transport limitations was observed to be instigated by the restriction of liquid water transport to catalyst sites. Additionally, conditions are revealed which yield similar polarization performance but dissimilar current distributions. In such cases, the transport limitations for different architectures and porous media affect polarization in different regions of the active area. Furthermore, the triple-serpentine flow-field used in this study performs better than the parallel flow-field under mass transport limited operating conditions. This indicates that the parallel flow-field used in this study is more susceptible to starvation than the triple-serpentine flow-field for the electrolyzer studied.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Surface processing and discharge-conditioning of high voltage electrodes for the Ra EDM experiment

The Ra EDM experiment uses a pair of high voltage electrodes to search for the atomic electric dipole moment of 225 Ra. We use identical, plane–parallel electrodes with a primary high gradient surface of 200 mm 2 to generate reversible DC electric fields. Our statistical sensitivity is linearly proportional to the electric field strength in the electrode gap. We adapted surface decontamination and processing techniques from accelerator physics literature to chemical polish and clean a suite of newly fabricated large-grain niobium and grade-2 titanium electrodes. Three pairs of niobium electrodes and one pair of titanium electrodes were discharge-conditioned with a custom high voltage test station at electric field strengths as high as +52.5 kV/mm and –51.5 kV/mm over electrode gap sizes ranging from 0.4 mm to 2.5 mm. One pair of large-grain niobium electrodes was discharge-conditioned and validated to operate at ±20 kV/mm with steady-state leakage current ≤ 25 pA (1σ) and a polarity-averaged 98 ± 19 discharges per hour. These electrodes were installed in the Ra EDM experimental apparatus, replacing a copper electrode pair, and were revalidated to ±20 kV/mm. Here, the niobium electrodes perform at an electric field strength 3.1 times larger than the legacy copper electrodes and are ultimately limited by the maximum output of our 30 kV bipolar power supply.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Generation of a controllable TNSA deuteron beam using deuterated metal targets

This study investigated the feasibility of using deuterated titanium targets for the generation of a target normal sheath acceleration (TNSA) deuteron beam. Commercial 25-μm-thick titanium foil was cut into 500 x 500-μm 2 squares and subsequently deuterated using different approaches. The spectra and total yields of all emitted ions were measured using a Thomson parabola ion spectrometer. It was found that a 24-h exposure to 1 atm of D 2 gas at 400°C is the most-efficient deuteration method, producing yields in the mid-10 11 deuterons per shot. The deuteron energy spectra changed from an exponential shape at low ion yields to exponentially modified Gaussians at higher yields. Simulations suggest that this effect is due to increased Coulomb interactions between the ions, which suppress the low energies. Separate campaigns will utilize the presented approach to produce a TNSA triton beam. Furthermore, two such targets will be used in a pitcher/catcher configuration to study the tritium–tritium reaction T(t, 2n)α.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Understanding the impact of the gas diffusion layer structure on catalyst utilization in the PEM water electrolyzer

A multiphysics half-cell model of a polymer electrolyte membrane water electrolyzer (PEMWE) was developed to probe impacts of the detailed 3-dimensional pore structure of the gas diffusion layer (GDL) on performance characteristics. We show that pores in the titanium GDL mesh led to significant underutilization of the catalyst layer (CL), with only 45% of the catalyst effectively utilized. This contradicts the assumption of uniform electron flow across the CL, as shown in graphical abstract (a), as near-zero current was observed near GDL pore regions and the current distribution in CL was influenced by GDL structure, as shown in graphical abstract (b). Instead, oxygen generation was primarily concentrated under the solid titanium regions, diffusing out around the pore walls. High current density peaks were also noted at the GDL-catalyst contact, correlating with degradation hotspots that were directly observed in companion experiments, as shown in graphical abstract (c). Collectively, these findings point to the critical importance of the heterogeneous GDL porous architecture not only for PEMWE efficiency but also for uneven degradation of the CL.

COMSOL↗
DOE OSTI2020

Design optimization of semiconductor piezoresistors with Schottky diode contacts

A modeling theory is developed to predict the performance of piezoresistors which incorporate Schottky diode electrical contacts. This new theory allows the design of high performance gauges which can be fabricated using NonLithographically-Based Microfabrication (NLBM) techniques. These semiconductor piezoresistors can be designed in customizable sizes and fabricated in parallel in order to integrate position sensing into MEMS flexural positioners. Customizable nanopositioning platforms will enable advances in a range of nano-scale fabrication and metrology applications. A semiconductor piezoresistor with Schottky diode contacts was fabricated and attached to a titanium flexure. This device is shown to match predicted electrical performance within about 8% and to show a gauge factor of 116, within 2% of the predicted value. Performance limits for Schottky diode semiconductor piezoresistors are identified to be about 127dB full noise dynamic range for a quarter bridge over a 10kHz sensor bandwidth on a 600µm width titanium flexure, making them ideal for sensing on meso-/micro-scale flexural positioners. Methods of reaching these performance bound are suggested and their impact on the sensor dynamic range are studied.

42 ENGINEERING↗