Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Investigation at High Subsonic Speeds of the Static Longitudinal and Lateral Stability Characteristics of Two Canard Airplane Configurations

The present investigation was conducted in the Langley high-speed 7-by 10-foot tunnel to determine the static longitudinal and lateral stability characteristics at high subsonic speeds of two canard airplane configurations previously tested at supersonic speeds. The Mach number range of this investigation extended from 0.60 to 0.94 and a maximum angle-of-attack range of -2dewg to 24deg was obtained at the lowest test Mach number. Two wing plan forms of equal area were studied in the present tests; one was a 60deg delta wing and the other was a trapezoid wing having an aspect ratio of 3, taper ratio of 0.143, and an unswept 80-percent-chord line. The canard control had a trapezoidal plan form and its area was approximately 11.5 percent of the wing area. The model also had a low-aspect-ratio highly swept vertical tail and twin ventral fins. The longitudinal control characteristics of the models were consistent with past experience at low speed on canard configurations in that stalling of the canard surface occurred at moderate and high control deflections for moderate values of angle of attack. This stalling could impose appreciable limitations on the maximum trim-lift coefficient attainable. The control effectiveness and maximum value of trim-lift was significantly increased by addition of a body flap having a conical shape and located slightly behind the canard surface on the bottom of the body. Addition of the canard surface at 0deg deflection had relatively little effect on overall directional stability of the delta-wing configuration; however, deflection of the canard surface from 0deg to 10deg had a large favorable effect on directional stability at high angles of attack for both the trapezoid- and delta-wing configurations.

Sleeman, William C., Jr.↗
NASA NTRS2002

Numerical Simulations for Landing Gear Noise Generation and Radiation

Aerodynamic noise from a landing gear in a uniform flow is computed using the Ffowcs Williams -Hawkings (FW-H) equation. The time accurate flow data on the surface is obtained using a finite volume flow solver on an unstructured and. The Ffowcs Williams-Hawkings equation is solved using surface integrals over the landing gear surface and over a permeable surface away from the landing gear. Two geometric configurations are tested in order to assess the impact of two lateral struts on the sound level and directivity in the far-field. Predictions from the Ffowcs Williams-Hawkings code are compared with direct calculations by the flow solver at several observer locations inside the computational domain. The permeable Ffowcs Williams-Hawkings surface predictions match those of the flow solver in the near-field. Far-field noise calculations coincide for both integration surfaces. The increase in drag observed between the two landing gear configurations is reflected in the sound pressure level and directivity mainly in the streamwise direction.

Morris, Philip J.↗
NASA NTRS1991

Transonic shock-induced dynamics of a flexible wing with a thick circular-arc airfoil

A simple flexible wing model with an 18-percent circular arc airfoil was constructed and tested in the Langley Transonic Dynamics Tunnel to investigate the dynamic characteristics that a wing might have under these conditions. In the region of shock-boundary layer oscillations, buffeting of the first bending mode was obtained. This mode was well separated in frequency from the shock boundary layer oscillations. A limit cycle oscillation was also measured in a 'third bending-like' mode, involving wing vertical bending and splitter plate motion, which was in the frequency range of the shock-boundary layer oscillations. Several model configurations were tested, and a few potential fixes were investigated.

Bennett, Robert M.↗
NASA NTRS1999

X-33 Hypersonic Aerodynamic Characteristics

Lockheed Martin Skunk Works, under a cooperative agreement with NASA, will build and fly the X-33, a half-scale prototype of a rocket-based, single-stage-to-orbit (SSTO), reusable launch vehicle (RLV). A 0.007-scale model of the X-33 604B0002G configuration was tested in four hypersonic facilities at the NASA Langley Research Center to examine vehicle stability and control characteristics and to populate an aerodynamic flight database in the hypersonic regime, The vehicle was found to be longitudinally controllable with less than half of the total body flap deflection capability across the angle of attack range at both Mach 6 and Mach 10. At these Mach numbers, the vehicle also was shown to be longitudinally stable or neutrally stable for typical (greater than 20 degrees) hypersonic flight attitudes. This configuration was directionally unstable and the use of reaction control jets (RCS) will be necessary to control the vehicle at high angles of attack in the hypersonic flight regime. Mach number and real gas effects on longitudinal aerodynamics were shown to be small relative to X-33 control authority.

Murphy, Kelly J.↗
NASA NTRS1999

X-33 Hypersonic Aerodynamic Characteristics

Lockheed Martin Skunk Works, under a cooperative agreement with NASA, will build and fly the X-33, a half-scale prototype of a rocket-based, single-stage-to-orbit (SSTO), reusable launch vehicle (RLV). A 0.007-scale model of the X-33 604B0002G configuration was tested in four hypersonic facilities at the NASA Langley Research Center to examine vehicle stability and control characteristics and to populate an aerodynamic flight database in the hypersonic regime. The vehicle was found to be longitudinally controllable with less than half of the total body flap deflection capability across the angle of attack range at both Mach 6 and Mach 10. At these Mach numbers, the vehicle also was shown to be longitudinally stable or neutrally stable for typical (greater than 20 degrees) hypersonic flight attitudes. This configuration was directionally unstable and the use of reaction control jets (RCS) will be necessary to control the vehicle at high angles of attack in the hypersonic flight regime. Mach number and real gas effects on longitudinal aerodynamics were shown to be small relative to X-33 control authority.

Murphy, Kelly J.↗
NASA NTRS1999

X-33 Hypersonic Aerodynamic Characteristics

Lockheed Martin Skunk Works, under a cooperative agreement with NASA, will design, build, and fly the X-33, a half-scale prototype of a rocket-based, single-stage-to-orbit (SSTO), reusable launch vehicle (RLV). A 0.007-scale model of the X-33 604BOO02G configuration was tested in four hypersonic facilities at the NASA Langley Research Center to examine vehicle stability and control characteristics and to populate the aerodynamic flight database for the hypersonic regime. The vehicle was found to be longitudinally controllable with less than half of the total body flap deflection capability across the angle of attack range at both Mach 6 and Mach 10. Al these Mach numbers, the vehicle also was shown to be longitudinally stable or neutrally stable for typical (greater than 20 degrees) hypersonic flight attitudes. This configuration was directionally unstable and the use of reaction control jets (RCS) will be necessary to control the vehicle at high angles of attack in the hypersonic flight regime. Mach number and real gas effects on longitudinal aerodynamics were shown to be small relative to X-33 control authority.

Murphy, Kelly J.↗
NASA NTRS1985

Heating rate distributions at Mach 10 on a circular body earth-to-orbit transport vehicle

A 0.0055-scale model of a single-stage-to-orbit transport vehicle with a circular body configuration was tested at Mach 10 to obtain heat transfer measurements and surface flow patterns. Phase-change paint and oil-flow tests were performed in the Langley 31-Inch Mach-10 Tunnel at angles of attack from 20 through 40 deg in 5-deg increments. Heat-transfer coefficient data are given for all angles of attack, and detailed oil-flow photographs are presented for windward and leeward surfaces at 25 and 40 deg angle of attack. Heating was found to similar to that previously determined for the Space Shuttle Orbiter, so that existing thermal protection systems would appear to be adequate for the proposed circular-body configurations.

Wells, W. L.↗
NASA NTRS1999

X-33 Hypersonic Aerodynamic Characteristics

Lockheed Martin Skunk Works, under a cooperative agreement with NASA, will build and fly the X-33, a half-scale prototype of a rocket-based, single-stage-to-orbit (SSTO), reusable launch vehicle (RLV). A 0.007-scale model of the X-33 604B0002G configuration was tested in four hypersonic facilities at the NASA Langley Research Center to examine vehicle stability and control characteristics and to populate an aerodynamic flight database i n the hypersonic regime. The vehicle was found to be longitudinally controllable with less than half of the total body flap deflection capability across the angle of attack range at both Mach 6 and Mach 10. At these Mach numbers, the vehicle also was shown to be longitudinally stable or neutrally stable for typical (greater than 20 degrees) hypersonic flight attitudes. This configuration was directionally unstable and the use of reaction control jets (RCS) will be necessary to control the vehicle at high angles of attack in the hypersonic flight regime. Mach number and real gas effects on longitudinal aerodynamics were shown to be small relative to X-33 control authority.

Murphy, Kelly J.↗
NASA NTRS1976

Results of an investigation of Reynolds effects on integrated vehicle elevon hinge moments and wing panel loads obtained with 0.010 scale model 72 OTS in the Rockwell trisonic wind tunnel (IA141)

Wind tunnel investigations were conducted on an 0.010-scale representation of the VL70-000140C Integrated Space Shuttle Launch Vehicle. The primary test objective was to obtain Reynolds number effects on orbiter elevon hinge moments and wing bending/torsional moments. Launch vehicle aerodynamic force data were also recorded. The elevon hinge moments, wing bending/torsional moments, and vehicle force data were recorded over an angle of attack range of -6 deg to +6 deg, an angle of sideslip range of -6 deg to +6 deg, at Mach numbers of 0.6, 0.975, 1.05 and 1.25. The Reynolds number was varied from a minimum of 4.5 million/foot to a maximum of 11.5 million/foot. The complete integrated configuration was tested with the orbiter elevons set at 0 deg and deflected to 9 deg on the outboard elevon and 10 deg on the inboard elevon. Testing was conducted in the TWT 19.7% porous transonic test section with the model sting mounted through the orbiter base. All aerodynamic force data were obtained from internal strain gage balance located in the orbiter.

Mennell, R. C.↗
NASA NTRS2012

Supersonic Retropropulsion Experimental Results from the NASA Ames 9- x 7-Foot Supersonic Wind Tunnel

Supersonic retropropulsion was experimentally examined in the Ames Research Center 9x7-Foot Supersonic Wind Tunnel at Mach 1.8 and 2.4. The experimental model, previously designed for and tested in the Langley Research Center Unitary Plan Wind Tunnel at Mach 2.4, 3.5 and 4.6, was a 5-in diameter 70-deg sphere-cone forebody with a 9.55-in long cylindrical aftbody. The forebody was designed to accommodate up to four 4:1 area ratio nozzles, one on the model centerline and the other three on the half radius spaced 120-deg apart. Surface pressure and flow visualization were the primary measurements, including high-speed data to investigate the dynamics of the interactions between the bow and nozzle shocks. Three blowing configurations were tested with thrust coefficients up to 10 and angles of attack up to 20-deg. Preliminary results and observations from the test are provided

Berry, Scott A.↗
NASA NTRS1990

A test fixture for measuring high-temperature hypersonic-engine seal performance

A test fixture for measuring the performance of several high temperature engine seal concepts was installed at the NASA Lewis Research Center. The test fixture was developed to evaluate seal concepts under development for advanced hypersonic engines such as those being considered for the National Aerospace Plane. The fixture can measure static seal leakage performance from room temperature up to 1500 F and air pressure differentials up to 100 psi. Performance of the seals can be measured while sealing against flat or engine simulated distorted walls, where distortions can be as large as 0.150 in. in only an 18 in. span. The fixture is designed to evaluate seals 3 feet long, a typical engine panel length. The seal channel can be configured to test square, circular, or rectangular seals that are nominally 0.5 in. high. The sensitivity of leakage performance to lateral or axial loading can also be measured using specially designed high temperature lateral and axial bellows preload systems. Leakage data for a candidate ceramic wafer engine seal is provided by way of example to demonstrate the test fixture's capabilities.

Steinetz, Bruce M.↗
NASA NTRS1982

QCSEE under-the-wing engine acoustic data

Both an over-the-wing (OTW) and an under-the-wing (UTW) experimental engine are discussed. The UTW engine had a variable-geometry fan exhaust nozzle and a variable-pitch fan that provided quick-response reverse thrust capability. An automatic digital control enabled optimal engine operation under all steady-state conditions as well as during forward and reverse thrust transient operation. The engine was tested at the Engine Noise Test Facility alone and with wind and flap segments to simulate an installation on a short-haul transport aircraft. The engine acoustic configuration was varied to give 14 test configurations. All of the acoustic test results from the UTW program at Lewis are presented as 1/3-octave-band sound pressure level (SPL) tabulations for all of the test points and some narrow-band spectra and 1/3-octave-band data plots for selected conditions.

Bloomer, H. E.↗
NASA NTRS2003

High Voltage Solar Array ARC Testing for a Direct Drive Hall Effect Thruster System

The deleterious effects of spacecraft charging are well known, particularly when the charging leads to arc events. The damage that results from arcing can severely reduce system lifetime and even cause critical system failures. On a primary spacecraft system such as a solar array, there is very little tolerance for arcing. Motivated by these concerns, an experimental investigation was undertaken to determine arc thresholds for a high voltage (200-500 V) solar array in a plasma environment. The investigation was in support of a NASA program to develop a Direct Drive Hall-Effect Thruster (112HET) system. By directly coupling the solar array to a Hall-effect thruster, the D2HET program seeks to reduce mass, cost and complexity commonly associated with the power processing in conventional power systems. In the investigation, multiple solar array technologies and configurations were tested. The cell samples were biased to a negative voltage, with an applied potential difference between them, to imitate possible scenarios in solar array strings that could lead to damaging arcs. The samples were tested in an environment that emulated a low-energy, HET-induced plasma. Short duration "trigger" arcs as well as long duration "sustained" arcs were generated. Typical current and voltage waveforms associated with the arc events are presented. Arc thresholds are also defined in terms of vo!tage, (current and power. The data will be used to propose a new, high-voltage (>300 V) solar array design for which the likelihood of damage from arcing is minimal.

Schneider, T.↗
NASA NTRS2004

High Voltage Solar Array Arc Testing for a Direct Drive Hall Effect Thruster System

The deleterious effects of spacecraft charging are well known, particularly when the charging leads to arc events. The damage that results from arcing can severely reduce system lifetime and even cause critical system failures. On a primary spacecraft system such as a solar array, there is very little tolerance for arcing. Motivated by these concerns, an experimental investigation was undertaken to determine arc thresholds for a high voltage (200-500 V) solar array in a plasma environment. The investigation was in support of a NASA program to develop a Direct Drive Hall-Effect Thruster (D2HET) system. By directly coupling the solar array to a Hall-effect thruster, the D2HET program seeks to reduce mass, cost and complexity commonly associated with the power processing in conventional power systems. In the investigation, multiple solar array technologies and configurations were tested. The cell samples were biased to a negative voltage, with an applied potential difference between them, to imitate possible scenarios in solar array strings that could lead to damaging arcs. The samples were tested in an environment that emulated a low-energy, HET-induced plasma. Short duration trigger arcs as well as long duration sustained arcs were generated. Typical current and voltage waveforms associated with the arc events are presented. Arc thresholds are also defined in terms of voltage, current and power. The data will be used to propose a new, high-voltage (greater than 300 V) solar array design for which the likelihood of damage from arcing is minimal.

Schneider, Todd↗
NASA NTRS1974

Effects of the six engine air breathing propulsion system on space shuttle orbiter subsonic stability and control characteristics

Experimental aerodynamic investigations were conducted on a 0.0405 scale representation of the -89B space shuttle orbiter in the 7.75 x 11.00 foot low speed wind tunnel during the time period September 4 - 14, 1973. The primary test objective was to optimize the air breathing propulsion system nacelle cowl-inlet design and to determine the aerodynamic effects of this design on the orbiter stability and control characteristics. Nacelle cowl-inlet optimization was determined from total pressure - static pressure measurements obtained from pressure rakes located in the left hand nacelle pod at the engine face station. After the optimum cow-inlet design, consisting of a 7 deg cowl lip angle, short cowl, 7 deg short diverter, and a nacelle toe-in angle of 5 deg was selected, the aerodynamic effects of various locations of this design were investigated. The 3 pod - 6 Nacelle configuration was tested both underwing and overwing in three different longitudinal locations. Orbiter control effectiveness, both with and without Nacelles, was investigated at elevon deflections of 0 deg, -10 deg and +15 deg and at aileron deflections of 0 deg and +10 deg about 0 deg elevon.

Mennell, R. C.↗
NASA NTRS1978

Effect of camber on the trimmed lift capability of a close-coupled canard-wing configuration

A close-coupled canard-wing configuration was tested in the Langely high-speed 7 by 10 foot tunnel at a Mach number of 0.30 to determine the effect of changing wing camber on the trimmed lift capability. Trimmed lift coefficients of near 2.0 were attained; however, the data indicated that the highest buffet-free trimmed lift coefficient attainable was approximately 1.30. The buffet used in this investigation were qualitative in nature and gave no indication of buffet intensity. Thus, the trimmed lift coefficient of near 2.0 might be attainable if the buffet intensity was not too high. The data showed that there was approximately a 10 percent variation in drag coefficient, for different model configurations, at a given trimmed lift coefficient. Large increases in wing lift had only small effects on canard lift.

Gloss, B. B.↗
NASA NTRS2005

Structural Benchmark Tests of Composite Combustion Chamber Support Completed

A series of mechanical load tests was completed on several novel design concepts for extremely lightweight combustion chamber support structures at the NASA Glenn Research Center (http://www.nasa.gov/glenn/). The tests included compliance evaluation, preliminary proof loadings, high-strain cyclic testing, and finally residual strength testing of each design (see the photograph on the left). Loads were applied with single rollers (see the photograph on the right) or pressure plates (not shown) located midspan on each side to minimize the influence of contact stresses on corner deformation measurements. Where rollers alone were used, a more severe structural loading was produced than the corresponding equal-force pressure loading: the maximum transverse shear force existed over the entire length of each side, and the corner bending moments were greater than for a distributed (pressure) loading. Failure modes initiating at the corner only provided a qualitative indication of the performance limitations since the stress state was not identical to internal pressure. Configurations were tested at both room and elevated temperatures. Experimental results were used to evaluate analytical prediction tools and finite-element methodologies for future work, and they were essential to provide insight into the deformation at the corners. The tests also were used to assess fabrication and bonding details for the complicated structures. They will be used to further optimize the design of the support structures for weight performance and the efficacy of corner reinforcement.

Krause, David L.↗