SEARCH · Engineering Papers

Results for “test bed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Development of an integrated set of research facilities for the support of research flight test

The Ames-Dryden Flight Research Facility (DFRF) serves as the site for the conduct of high-risk flight research on many one-of-a-kind test vehicles like the X-29A advanced technology demonstrator, F-16 advanced fighter technology integration (AFTI), AFTI F-111 mission adaptive wing, and F-18 high-alpha research vehicle (HARV). Ames-Dryden is on a section of the historic Muroc Range. The facility is oriented toward the testing of high-performance aircraft, as shown by its part in the development of the X-series aircraft. Given the cost of research flight test and the complexity of today's systems-driven aircraft, an integrated set of ground support experimental facilities is a necessity. In support of the research flight test of highly advanced test beds, the DFRF is developing a network of facilities to expedite the acquisition and distribution of flight research data to the researcher. This network consists of an array of experimental ground-based facilities and systems as nodes and the necessary telecommunications paths to pass research data and information between these facilities. This paper presents a status of the current network, an overview of current developments, and a prospectus on future major enhancements.

Moore, Archie L.↗

NASA NTRS1988

Rotating disk transition due to isolated roughness with intense acoustic irradiation

The low transition Reynolds numbers associated with boundary-layers which exhibit crossflow instability have made them an important area of study in fluid mechanics. An excellent test bed for the study of this flow is a flat disk rotating in still fluid. An experimental investigation of stability and transition of a rotating disk boundary-layer has been conducted. The effects of isolated roughness elements and acoustic forcing, both alone and in combination, were considered. The flow showed no receptivity to intense monochromatic acoustic forcing except in the presence of sizable roughness. A case was investigated where the growth of the primary instability, seeded by an isolated roughness element, was positively altered in the presence of sound, leading to a downstream movement of transition. In agreement with the work of several investigators, the results of this study suggest that receptivity to long wavelength phenomena, such as traveling sound waves, is contingent upon the presence of strong localized pressure gradients (such as those introduced by roughness) to reduce the length scales of the disturbance to those which are consistent with unstable wavelengths in the flow field.

Waitz, Ian A.↗

NASA NTRS1986

Mass flow measurement of liquid cryogens using the triboelectric effect

A cross correlator technique using triboelectric technology has been shown to be a feasible method to measure liquid flow rate for liquid nitrogen and JP4 jet fuel. This technology, invented and pioneered by Auburn International, Inc., is also expected to be suitable for use with all other insulating liquids and cryogens. The technology described is particularly well suited for cryogenic use, since the sensor is non-contacting and non-intrusive, and therefore, causes no additional pressure drop within the flow stream. Further development of the in-line sensor is required to produce a prototypical version for the test purposes under SSME fuel flow conditions. However, with the knowledge gained from this feasibility study, it is very likely that an acceptable sensor design for a full test bed evaluation could be produced.

Dechene, Ronald L.↗

NASA NTRS1988

Design and implementation of a microcomputer-based user interface controller for bursted data communications satellite ground terminals

The NASA Lewis Research Center is developing a laboratory-based satellite communications test bed for evaluation of state-of-the-art communications hardware and systems. Most of the digital components of the ground terminals are being constructed in-house at NASA Lewis. One of the ground terminal subsystems, the user interface controller, controls the connection and disconnection of all users to the communication network. The role of the user interface controller in the ground terminal is described and the design and implementation of the microcomputer-based subsystem is discussed.

Shalkhauser, Mary Jo W.↗

NASA NTRS1988

The 25 kWe solar thermal Stirling hydraulic engine system: Conceptual design

The conceptual design and analysis of a solar thermal free-piston Stirling hydraulic engine system designed to deliver 25 kWe when coupled to a 11 meter test bed concentrator is documented. A manufacturing cost assessment for 10,000 units per year was made. The design meets all program objectives including a 60,000 hr design life, dynamic balancing, fully automated control, more than 33.3 percent overall system efficiency, properly conditioned power, maximum utilization of annualized insolation, and projected production costs. The system incorporates a simple, rugged, reliable pool boiler reflux heat pipe to transfer heat from the solar receiver to the Stirling engine. The free-piston engine produces high pressure hydraulic flow which powers a commercial hydraulic motor that, in turn, drives a commercial rotary induction generator. The Stirling hydraulic engine uses hermetic bellows seals to separate helium working gas from hydraulic fluid which provides hydrodynamic lubrication to all moving parts. Maximum utilization of highly refined, field proven commercial components for electric power generation minimizes development cost and risk.

White, Maurice↗

NASA NTRS1986

Extending the granularity of representation and control for the MIL-STD CAIS 1.0 node model

The Common APSE (Ada 1 Program Support Environment) Interface Set (CAIS) (DoD85) node model provides an excellent baseline for interfaces in a single-host development environment. To encompass the entire spectrum of computing, however, the CAIS model should be extended in four areas. It should provide the interface between the engineering workstation and the host system throughout the entire lifecycle of the system. It should provide a basis for communication and integration functions needed by distributed host environments. It should provide common interfaces for communications mechanisms to and among target processors. It should provide facilities for integration, validation, and verification of test beds extending to distributed systems on geographically separate processors with heterogeneous instruction set architectures (ISAS). Additions to the PROCESS NODE model to extend the CAIS into these four areas are proposed.

Rogers, Kathy L.↗

NASA NTRS1986

The TAVERNS emulator: An Ada simulation of the space station data communications network and software development environment

The Space Station DMS (Data Management System) is the onboard component of the Space Station Information System (SSIS) that includes the computers, networks and software that support the various core and payload subsystems of the Space Station. TAVERNS (Test And Validation Environment for Remote Networked Systems) is a distributed approach for development and validation of application software for Space Station. The TAVERNS concept assumes that the different subsystems will be developed by different contractors who may be geographically separated. The TAVERNS Emulator is an Ada simulation of a TAVERNS on the ASD VAX. The software services described in the DMS Test Bed User's Manual are being emulated on the VAX together with simulations of some of the core subsystems and a simulation of the DCN. The TAVERNS Emulator will be accessible remotely from any VAX that can communicate with the ASD VAX.

Howes, Norman R.↗

NASA NTRS1989

Free-piston Stirling technology for space power

An overview is presented of the NASA Lewis Research Center free-piston Stirling engine activities directed toward space power. This work is being carried out under NASA's new Civil Space Technology Initiative (CSTI). The overall goal of CSTI's High Capacity Power element is to develop the technology base needed to meet the long duration, high capacity power requirements for future NASA space missions. The Stirling cycle offers an attractive power conversion concept for space power needs. Discussed here is the completion of the Space Power Demonstrator Engine (SPDE) testing-culminating in the generation of 25 kW of engine power from a dynamically-balanced opposed-piston Stirling engine at a temperature ratio of 2.0. Engine efficiency was approximately 22 percent. The SPDE recently has been divided into two separate single-cylinder engines, called Space Power Research Engine (SPRE), that now serve as test beds for the evaluation of key technology disciplines. These disciplines include hydrodynamic gas bearings, high-efficiency linear alternators, space qualified heat pipe heat exchangers, oscillating flow code validation, and engine loss understanding.

Slaby, Jack G.↗

NASA NTRS1989

Evaluation of the ride quality of a light twin engine airplane using a ride quality meter

A ride quality meter was used to establish the baseline ride quality of a light twin-engine airplane planned for use as a test bed for an experimental gust alleviation system. The ride quality meter provides estimates of passenger ride discomfort as a function of cabin noise and vibration (acceleration) in five axes (yaw axis omitted). According to the ride quality meter, in smooth air the cabin noise was the dominant source of passenger discomfort, but the total discomfort was approximately the same as that for the smooth-air condition. The researcher's subjective opinion, however, is that the total ride discomfort was much worse in the moderate turbulence than it was in the smooth air. The discrepancy is explained by the lack of measurement of the low-frequency accelerations by the ride quality meter.

Stewart, Eric C.↗

NASA NTRS1989

Design, fabrication and test of the RL10 derivative II chamber/primary nozzle

The design, fabrication and test of the RL10-II chamber/primary nozzle was accomplished as part of the RL10 Product Improvement Program (PIP). The overall goal of the RL10 PIP was to gain the knowledge and experience necessary to develop new cryogenic upper stage engines to fulfill future NASA requirements. The goal would be reached by producing an RL10 engine designed to be reusable, operate at several thrust levels, and have increased performance. The goals for the chamber/primary nozzle task were: (1) to design a reusable assembly capable of operation at increased mixture ratio and low thrust; (2) to fabricate three assemblies using new or updated techniques where possible; and (3) to test one assembly to verify the design and construction. The design and fabrication phases produced an assembly having improved features such as single piece reinforcing band segments (i.e., Mae West segments) and relocated tube exit braze joints (i.e., hooked tube exit). In addition, a computer program was developed to design the chamber tubes to meet both performance and heat transfer requirements. The test phase showed the specific impulse of the test bed engine system to be as predicted. These results, along with the heat transfer data obtained, sufficiently proved the overall design of the RL10-II recontoured and shortened chamber/primary nozzle assembly.

Marable, R. W.↗

NASA NTRS1989

The experiments of LIPS 3

LIPS 3 is a member of the Living Plume Shield series of spacecraft. In each LIPS project, the plume shield, a simple sheet metal cone, was structurally stiffened, and an active satellite was then built around it. The original purpose of the plume shield was to prevent the plume from solid propellent engines, which are fired outside the atmosphere after the aerodynamic shroud is jettisoned, from reaching the primary payload. The surface of LIPS 3 facing the plume also functioned in this manner, but the anterior surfaces were unaffected, and it was there that all solar arrays, sensors, and experiments were mounted. The purpose of LIPS 3 was to provide a test bed for new space power sources. With the long delays projected for schedules of the STS and other major launch systems, it appeared that a decade might pass before long term flight data could be obtained on many new and innovative power sources. The fact that a launch scheduled for early in 1987 required a plume shield was seen as a unique opportunity to obtain some of this data in a timely manner. The LIPS 3 system, the experiments placed aboard, and the experiment data acquisition subsystem are described. Various problems were encountered during integration and after launch; those which appear to effect the accuracy of experimental results are discussed. A preliminary description is given of the accuracy of the flight experiment data.

Severns, J. G.↗

NASA NTRS1988

Power components for the Space Station 20-kHz power distribution system

Since 1984, NASA Lewis Research Center was developing high power, high frequency space power components as part of The Space Station Advanced Development program. The purpose of the Advanced Development program was to accelerate existing component programs to ensure their availability for use on the Space Station. These components include a rotary power transfer device, remote power controllers, remote bus isolators, high power semiconductor, a high power semiconductor package, high frequency-high power cable, high frequency-high power connectors, and high frequency-high power transformers. All the components were developed to the prototype level and will be installed in the Lewis Research Center Space Station power system test bed.

Renz, David D.↗

NASA NTRS1989

Free-piston Stirling technology for space power

Slaby, Jack G.↗

NASA NTRS1989

Grain metamorphism in polar nitrogen ice on Triton

The rate of nitrogen grain growth on putative N2-rich polar caps on Triton is calculated. For most plausible assumptions of independent variables, mean grain sizes in polar N2 are meter-scale. Triton's polar caps should constitute the definitive solar-system test bed for the process of ice grain metamorphism. Interpretation of data already in hand may require long path length through condensed N2, possibly due to grain growth. Upcoming Voyager data may clarify the situation, although possible complications in detecting a glaze of N2 ice exist.

Zent, Aaron P.↗

NASA NTRS1989

Definition of avionics concepts for a heavy lift cargo vehicle, appendix A

The major objective of the study task was to define a cost effective, multiuser simulation, test, and demonstration facility to support the development of avionics systems for future space vehicles. This volume provides the results of the main simulation processor selection study and describes some proof-of-concept demonstrations for the avionics test bed facility.

Source record↗

NASA NTRS1989

Advanced Turbine Technology Applications Project (ATTAP)

Work to develop and demonstrate the technology of structural ceramics for automotive engines and similar applications is described. Long-range technology is being sought to produce gas turbine engines for automobiles with reduced fuel consumption and reduced environmental impact. The Advanced Turbine Technology Application Project (ATTAP) test bed engine is designed such that, when installed in a 3,000 pound inertia weight automobile, it will provide low emissions, 42 miles per gallon fuel economy on diesel fuel, multifuel capability, costs competitive with current spark ignition engines, and noise and safety characteristics that meet Federal standards.

Source record↗

NASA NTRS1989

Preliminary design document: Ground based testbed for avionics systems

The design and interface requirements for an avionics Ground Based Test bed (GBT) to support Heavy Lift Cargo Vehicles (HLCV) is presented. It also contains data on the vehicle subsystem configurations that are to be supported during their early, pre-PDR developmental phases. Several emerging technologies are also identified for support. A Preliminary Specification Tree is also presented.

Source record↗

NASA NTRS1989

Support trusses for large precision segmented reflectors: Preliminary design and analysis

Precision Segmented Reflector (PSR) technology is currently being developed for a range of future applications such as the Large Deployable Reflector. The structures activities at NASA-Langley are outlined in support of the PSR program. Design concepts are explored for erectable and deployable support structures which are envisioned to be the backbone of these precision reflectors. Important functional requirements for the support trusses related to stiffness, mass, and surface accuracy are reviewed. Proposed geometries for these structures and factors motivating the erectable and deployable designs are discussed. Analytical results related to stiffness, dynamic behavior, and surface accuracy are presented and considered in light of the functional requirements. Results are included for both a 4-meter-diameter prototype support truss which is currently being designed as the Test Bed for the PSR technology development program, and for two 20-meter support structures.

Collins, Timothy J.↗