SEARCH · Engineering Papers

Results for “graphitization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

All sources NASA NTRS DOE OSTI

NASA NTRS1984

Free edge strain concentrations in real composite laminates: Experimental-theoretical correlation

The magnitude of the maximum shear strain at the free edge of axially loaded theta (2)/-theta(2)(s) and (+ or - theta(2) (s) composite laminates was investigated experimentally and numerically to ascertain the actual value of strain concentration in resin matrix laminates and to determine the accuracy of finite element results. Experimental results using moire interferometry show large, but finite, shear strain concentrations at the free edge of graphite-epoxy and graphite-polyimide laminates. Comparison of the experimental results with those obtained using several different finite element representations showed that a four node isoparametric finite element provided the best and most trouble free numerical results. The results indicate that the ratio of maxium shear strain at the free edge to applied axial strain varies with fiber orientation and does not exceed nine for the most critical angle which is 15 deg.

Herakovich, C. T.↗

NASA NTRS1984

Dual ion beam deposition of carbon films with diamondlike properties

A single and dual ion beam system was used to generate amorphous carbon films with diamond like properties. A methane/argon mixture at a molar ratio of 0.28 was ionized in the low pressure discharge chamber of a 30-cm-diameter ion source. A second ion source, 8 cm in diameter was used to direct a beam of 600 eV Argon ions on the substrates (fused silica or silicon) while the deposition from the 30-cm ion source was taking place. Nuclear reaction and combustion analysis indicate H/C ratios for the films to be 1.00. This high value of H/C, it is felt, allowed the films to have good transmittance. The films were impervious to reagents which dissolve graphitic and polymeric carbon structures. Although the measured density of the films was approximately 1.8 gm/cu cm, a value lower than diamond, the films exhibited other properties that were relatively close to diamond. These films were compared with diamondlike films generated by sputtering a graphite target.

Mirtich, M. J.↗

NASA NTRS1984

Evaluation of thermobarometers for garnet peridotites

Twenty-one geothermometers and six geobarometers are evaluated for accuracy and precision for garnet lherzolites, with a suite of well-equilibrated xenoliths from kimberlites of northern Lesotho. Accuracy was tested by comparison of P-T estimates for a diamond-bearing and a graphite-bearing xenolith with the experimentally determined diamond-graphite univariant curve and by comparison of P-T estimates for phlogopite-bearing xenoliths to the high-temperature stability limit of phlogopite. Precision was evaluated by measuring the scatter of P-T estimates for each of four xenoliths from a wide range of P and T when many point analyses of the constituent minerals are used for P-T estimation. Most satisfactory is a thermobarometer composed of the uncorrected diopside-enstatite miscibility gap of Lindsley and Dixon (1976), combined with the uncorrected isopleths for aluminum in enstatite coexisting with pyrope of MacGregor (1974). The inflection observed in the northern Lesotho paleogeotherm cannot be an artifact of the method of temperature estimation.

Finnerty, A. A.↗

NASA NTRS1984

Processing and flammability parameters of bismaleimide and some other thermally stable resin matrices for composites

The effect of processing variables on the flammability and mechanical properties of state-of-the-art and advanced resin matrices for graphite composites were studied. Resin matrices which were evaluated included state-of-the-art epoxy, phenolic-novolac, phenolic-Xylok, two types of bismaleimides, benzyl, polyethersulfone, and polyphenylsulfone. Comparable flammability and thermochemical data on graphite-reinforced laminates prepared with these resin matrices are presented, and the relationship of some of these properties to the anaerobic char yield of the resins is described.

Kourtides, D. A.↗

NASA NTRS1986

Stiffness Study of Wound-Filament Pressure Vessels

Report presents theoretical and experimental study of stiffness of lightweight, jointed pressure vessels made of wound graphite fibers and epoxy. Specimens fabricated from layers of graphite fibers, wet with epoxy, on aluminum mandrel. Segment ends thickened with interspersed layers of axially oriented fibers to reduce pinhole bearing stresses and local deformations. Segments cured at 390 degrees F (199 degrees C). Report presents results of vibrational tests of one-quarter-scale models of wound-filament pressure vessels.

Verderaime, V.↗

NASA NTRS1984

Effects of Constituent Properties on Compression Failure Mechanisms

Compression failure mechanisms were investigated through the analysis of matrix-embedded fiber bundles. The use of fiber bundle specimens can provide much needed information on compression failure mechanisms because failure of the bundle is well contained and can be monitored during testing. The method can clearly distinguish between buckling-induced failure and shear-induced failure. The results indicate that WY and T300 graphite fibers and E-glass fiber fail in buckling while the high-modulus P75S graphite fiber fails in shear. Buckling-induced failure becomes more evident with low-modulus fiber in softer epoxy.

Hahn, H. T.↗

NASA NTRS1985

Effect of substituted phenylnadimides on processing and properties of PMR polyimide composites

Three nitrophenylnadimide cure initiators and two phenylnadimides (without nitros) were evaluated as additives to PMR-15 resins and Celion 6000 graphite fiber composites. The results of a resin screening study eliminated all of the additives except 3-nitrophenylnadimide (NO2PN) for use as a low temperature curing additive for PMR-15. Thus, NO2PN and the two control additives were investigated in PMR-15 formulations from which Celion 6000 graphite fiber/PMR-15 composites were processed both with low temperature (274 C) and normal (316 C) cure cycles. Comparisons of the two processing cycles, the resultant glass transition temperatures (Tg), the ambient, 274 and 316 C composite mechanical properties determined before and after 316 C postcure, the 316 C thermo-oxidative weight losses and the retention of 316 C composite mechanical properties are presented. Empirical correlations of the type and amount of nadimide additives with processing parameters, Tg, composite mechanical properties, composite thermo-oxidative stability and long term retention of 316 C composite mechanical properties are also presented.

Alston, W. B.↗

NASA NTRS1984

Automated assembly of Gallium Arsenide and 50-micron thick silicon solar cell modules

The TRW automated solar array assembly equipment was used for the module assembly of 300 GaAs solar cells and 300 50 micron thick silicon solar cells (2 x 4 cm in size). These cells were interconnected with silver plated Invar tabs by means of welding. The GaAs cells were bonded to Kapton graphite aluminum honeycomb graphite substrates and the thin silicon cells were bonded to 0.002 inch thick single layer Kapton substrates. The GaAs solar cell module assembly resulted in a yield of 86% and the thin cell assembly produced a yield of 46% due to intermittent sticking of weld electrodes during the front cell contact welding operation. (Previously assembled thin cell solar modules produced an overall assembly yield of greater than 80%).

Mesch, H. G.↗

NASA NTRS1985

Nonlinear response and failure characteristics of internally pressurized composite cylindrical panels

Results of an experimental and analytical study of the nonlinear response and failure characteristics of internally pressurized 4- to 16-ply-thick graphite-epoxy cylindrical panels are presented. Specimens with clamped boundaries simulating the skin between two frames and two stringers of a typical transport fuselage were tested to failure. Failure results of aluminum specimens are compared with the graphite-epoxy test results. The specimens failed at their edges where the local bending gradients and interlaminar stresses are maximum. STAGS nonlinear two-dimensional shell analysis computer code results are used to identify regions of the panels where the response is independent of the axial coordinate. A geometrically nonlinear one-dimensional cylindrical panel analysis was derived and used to determine panel response and interlaminar stresses. Inclusion of the geometric nonlinearity was essential for accurate prediction of panel response. The maximum stress failure criterion applied to the predicted tensile stress in the fiber direction agreed best with the experimentally determined first damage pressures.

Boitnott, R. L.↗

NASA NTRS1984

A morphological study of silicon carbide prepared by chemical vapor deposition

Surface morphologies of SiC deposits obtained via chemical vapor deposition (CVD) were studied as functions of substrate surface temperature and the concentration of the silicon and carbon source material, methyltrichlorosilane. Substrates of graphite and alpha-SiC crystals were used. Explanations of the observed morphologies on graphite substrates and their marked changes with temperature are given in terms of chemical kinetics and mass transport arguments. The results of thermodynamic calculations were used to help explain the observed morphologies of the deposits on alpha-SiC substrates.

Tsui, P.↗

NASA NTRS1984

A thermoplastic polyimidesulfone

A polymer system has been prepared which has the excellent thermoplastic properties generally associated with polysulfones, and the solvent resistance and thermal stability of aromatic polyimides. This material, with improved processability over the base polyimide, can be processed in the 260-325 C range in such a manner as to yield high quality, tough unfilled moldings; strong, high-temperature-resistant adhesive bonds; and well consolidated, graphite-fiber-reinforced moldings (composites). The unfilled moldings have physical properties that are similar to aromatic polysulfones which demonstrates the potential as an engineering thermoplastic. The adhesive bonds exhibit excellent retention of initial strength levels even after thermal aging for 5000 hours at 232 C. The graphite-fiber-reinforced moldings have mechanical properties which makes this polymer attractive for the fabrication of structural composites.

St. Clair, T. L.↗

NASA NTRS1984

Rheological characterization of addition polyimide matrix resins and prepregs

Although graphite-reinforced polyimide matrix composites offer outstanding specific strength and stiffness, together with high thermal oxidative stability, processing problems connected with their rheological behavior remain to be addressed. The present rheological studies on neat polyimide resin systems encountered outgassing during cure. A staging technique has been developed which can successfully handle polyimide samples, and novel methods were applied to generate rheological curves for graphite-reinforced prepregs. The commercial graphite/polyimide systems studied were PRM 15, LARC 160, and V378A.

Maximovich, M. G.↗

NASA NTRS1985

Electron emission and acoustic emission from the fracture of graphite/epoxy composites

In past studies it has been shown that the fracture of materials leads to the emission of a variety of species, including electrons, ions, neutral molecules, and photons, all encompassed by the term 'fractoemission' (FE). In this paper, electron emission (EE) from the fracture of single graphite fibers and neat epoxy resin is examined. Measurements of EE are also combined with the detection of acoustic emission (AE) during the testing of graphite-epoxy composite specimens with various fiber orientation. The characteristics of these signals are related to known failure mechanisms in fiber-reinforced plastics. This study suggests that by comparing data from AE and FE measurements, one can detect and distinguish the onset of internal and external failure in composites. EE measurements are also shown to be sensitive to the locus of fracture in a composite material.

Dickinson, J. T.↗

NASA NTRS1986

Monitoring Prepregs As They Cure

Quality IR spectra obtained in dynamic heating environment. New technique obtains quality infrared spectra on graphite-fiber-reinforced, polymeric-matrix-resin prepregs as they cure. Technique resulted from modification of diffuse reflectance/Fourier transform infrared (DR/FTIR) technique previously used to analyze environmentally exposed cured graphite composites. Technique contribute to better understanding of prepreg chemistry/temperature relationships and development of more efficient processing cycles for advanced materials.

Young, P. R.↗

NASA NTRS1986

Carbon Shields for Intercalated Fiber Conductors

Stability in air increased by depositing amorphous carbon. Initially graphite fibers intercalated (insertion of atoms or molecules between graphite layers). Next, conductor coated with diamondlike amorphous carbon. Coating applied in same chamber as intercalation reaction or alternate deposichamber is used. Deposition of carbon accomplished by any number of techniques. tion Ion-beam sputter-deposition and RF plasma techniques have been used, but dc plasma and others work also. Potential uses include conductive epoxy composites, tether conductors, signal wire, and power cables.

Banks, B. A.↗

NASA NTRS1986

Lightweight Ceramic Insulation

Fiber burnout process yields low densities. Low density attained by process of sacrificial burnout. Graphite or carbon fibers mixed into slurry of silica, alumina, and boron-compound fibers in amounts ranging from 25 to 75 percent of total fiber content by weight. Mixture formed into blocks and dried. Blocks placed in kiln and heated to 1,600 degrees F(870 degrees C) for several hours. Graphite or carbon fibers slowly oxidize away, leaving voids and reducing block density. Finally, blocks heated to 2,350 degrees F (1,290 degrees C) for 90 minutes to bond remaining ceramic fibers together. Developed for use on Space Shuttle and other spacecraft, rigid insulation machined to requisite shape and bonded in place.

Wheeler, W. H.↗

NASA NTRS1986

Reinforcing the Separators for Lithium/Carbon Cells

Fabrication of lithium/carbon batteries simplified by attachment of perforated nickel-foil, graphite-cloth, or graphite-paper backings to glass-fiber separators. Both nickel and carbon backings appear viable. Because perforated nickel foil already manufactured by electroforming, no obstacle to creation of very thin, very porous nickel foil to serve as backing: Thicknesses of 20 micrometers with porosities above 50 percent practicable.

Du Fresne, E. R.↗

NASA NTRS1985

Metallic Foams

The formation of metallic foams by use of a blowing agent in the melt was investigated. It was attempted to produce a metallic foam by melting a mixture of Cu powder and graphite in a SPAR rocket. The graphite combines with the oxide on the copper to form Co and acts as a blowing agent. No foam was formed, and it could not be determined whether the foam fails to form, forms but was lost to surface tension instabilities, or is destroyed by incomplete solidification before reentry.

Pond, R. B.↗