Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “difficult”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Crystallographic ordering of Al and Sn in α-Ti

Increasing attention is being paid to α (2) Ti 3 (Al,Sn) precipitation from the α phase of titanium alloys owing to its effect on slip band formation, localisation and the implications for fatigue performance in jet engine titanium. However, the early stages of α 2 precipitation have historically been difficult to observe by electron microscopy, neutron diffraction or atom probe analysis. Here, small angle X-ray scattering is used to reexamine the phase boundary in binary Ti-Al and Ti-Sn alloys with around 500 ppmw O. It is found that the phase boundaries in the literature are approximately correct, at 6.2 wt.% Al and 16.9 wt.% Sn, and that this favours the use of Al as a solid solution strengthener over Sn for ambient temperature applications. However, once O content and phase partitioning in α + β alloys are taken into account, this implies that Al eq limits for future alloy design of critical rotating parts should be lowered substantially.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Surface oxygen exchange kinetics of mixed conducting oxides: Dilatometric vs electrical conductivity relaxation study

The surface oxygen exchange kinetics of mixed ionic-electronic conducting (MIEC) oxides play a crucial role in a variety of applications, including solid oxide fuel/electrolysis cells (SOFCs/SOECs), permeation membranes and sensors. To date, a variety of methods, including isotope exchange, electrical conductivity, optical absorptivity and thermogravimetry relaxation, and impedance spectroscopy have been used to measure the oxygen exchange coefficient of MIEC oxides. Each of these methods have their advantages and limitations, depending on the physical and chemical properties of the investigated materials and their sample dimensions and densities. Here, we demonstrate the ability to precisely measure the surface oxygen exchange coefficient (k chem ) of MIEC model material Pr 0.1 Ce 0.9 O 2-δ (PCO) by use of dilatometric relaxation measurements, particularly of interest for materials that exhibit larger chemical expansion coefficients. This is achieved by use of porous bulk specimens to ensure that the contribution of oxygen exchange to the overall kinetics is dominant. We demonstrate that k chem values extracted from chemical expansion relaxation measurements on PCO are nearly identical to those derived from electrical conductivity relaxation measurements. As a result, this provides the opportunity to precisely investigate the oxygen exchange and chemical expansion kinetics of a wide range of materials used in high-temperature applications, particularly where more conventional methods are difficult or inappropriate to apply.

(Pr,Ce)O2-x↗
DOE OSTI2025

Shining light on nanoscale ‘vine-on-stick’ eutectic structures in the Al-Ce-Ni system

Multiphase eutectics often comprise entangled solid phases with nanoscale periodicity, making it difficult to unravel their 3D connectivity using conventional 2D techniques. Among such systems, the three-phase eutectic Al-Al 11 Ce 3 -Al 3 Ni stands out for its ultrafine (∼100 nm) interphase spacing and promising creep resistance, yet its microstructure remains relatively unexplored despite its potential for high-temperature applications. Here, we use scanning hard X-ray microscopy with an unprecedented ∼10 nm pixel size to resolve its 3D morphology. Reconstructions reveal a novel “vine-on-stick” motif, wherein Al 11 Ce 3 wraps around Al 3 Ni pillars. Analysis of phase tortuosities confirms that Al 11 Ce 3 exhibits more convoluted morphologies than Al 3 Ni. No orientation relationship was observed between the two intermetallics, suggesting that growth is controlled by local solute gradients rather than epitaxy. Fragmentation of intermetallics along their longitudinal axis suggests a Rayleigh-type breakup mechanism in solid state. The “vine-on-stick” pattern may generalize to other alloy systems with variable interfacial anisotropies and low mutual solubilities.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Induction ultrafast sintering

This study proposes and demonstrates induction ultrafast sintering (IUS), which enables rapid densification of refractory and other materials via two contactless modalities: direct IUS (d-IUS), where heating occurs through electromagnetic coupling with the sample, and susceptor IUS (s-IUS), where heating is achieved indirectly via an induction-heated metal case. Ultrahigh heating rates of ∼75 to >450 °C/s and temperatures exceeding 2500 °C are readily achieved. Both d-IUS and s-IUS densify molybdenum to high densities within 120 s, with only ∼1–3 % porosity observed by image analysis. Similarly, 3 mol % yttria-stabilized zirconia (3YSZ) reaches ∼97 % relative density in 30 s via s-IUS. This study further demonstrates ultrafast reactive sintering of two difficult-to-sinter materials: a refractory compositionally complex alloy–carbide (RCCA–CCC) composite, NbMoTaW–(Nb 0.37 Mo 0.11 Ta 0.39 W 0.13 ) 2 C, using d-IUS, and a compositionally complex silicide (CCS), (Mo 1/3 Nb 1/3 Zr 1/3 )Si 2 , using s-IUS. This IUS platform offers a versatile route for high-throughput materials discovery and energy-efficient fabrication of bulk refractory materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Dynamic security assessment of systems powered only by grid-forming power plants with uncertain dispatch using polynomial vectors

A modern challenge in power engineering is to perform the dynamic security assessment (DSA) of grids that are 100% powered by inverter-based resources (IBRs). Addressing this challenge is difficult because: (i) the dispatch of IBRs can be uncertain as a result of the variability of renewable resources and (ii) they have hard current control limits that cannot be neglected, contrasting synchronous machines. To address this problem, this paper sets forth a framework to conduct DSA of bulk power systems that are 100% powered by grid-forming IBRs. Furthermore, the framework considers that IBR operational conditions are unknown but bounded by a zonotope which is also expressed as a polynomial vector for uncertainty propagation via Dormand–Prince integration. The framework is applied to modified versions of the WSCC 9-bus and IEEE 39-bus grids.

14 SOLAR ENERGY↗
DOE OSTI2025

Developing aqueous solubilizing agents as an alternative to solvent extraction

Here, advancing separations science is important for the entire field of chemistry. One partitioning technique that would benefit from improvement is solvent extraction. Despite its effective and widespread use, the method suffers from some problems: generation of flammable organic waste, lengthy process times, and safety concerns associated with contacting organic solvents with acidic aqueous solutions. We developed an alternative separation method inspired by solvent extraction that side-steps those issues. Toward this end, we identified that the functionality of an extractant (an agent used in solvent extraction to pull analytes from the aqueous phase into the organic phase) would change if it was modified for water solubility. In this alternative scenario, the extractant transforms into an “aqueous solubilizing agent.” We discovered that adding this aqueous solubilizing agent alongside a precipitating agent caused the contaminants to precipitate, but not the analyte. This separation concept was demonstrated within the bounds of one of the most difficult partitioning problems, separating minor actinides (Am 3+ ) from lanthanides (Ln 3+ ). We discovered that the (HSO 3 Ph) 4 BTP (aq) aqueous solubilizing agent prevented Am 3+ (aq) from precipitating with Ln 3+ (aq) when f-element precipitating agents (NaF (aq) or HF (aq) ) were added. This separation boasts impressive Am 3+ (aq) recovery yield (90 ± 2 %), near quantitative Ln 3+ (aq) removal, and high separation factors [>3000, Am 3+ (aq) vs. Nd 3+ (aq) ]. It seems likely – given the large number of candidate extractants that could be modified for aqueous solubility and the numerous combinations of existing solubilizing and precipitating agents – that this alternative approach could be used broadly in place of solvent extraction and solve other important separation problems.

(HSO3Ph)4BTP(aq)↗
DOE OSTI2026

Full-scale validation gaps and opportunities for low-head hydropower: a review and perspective

Hydropower is undergoing technological innovation as future development increasingly targets low-head sites (<10 m), primarily through retrofits, rehabilitation, and upgrades of existing infrastructure. This shift toward smaller systems creates a timely opportunity: unlike conventional large projects, many emerging low-head technologies may be small enough for direct full-scale validation. Full-scale testing is particularly important for environmental mitigation technologies, including fish passage, sediment continuity, and water-quality improvements, whose performance is difficult to assess reliably using reduced-scale models. Yet adoption remains constrained by the limited risk-bearing capacity of small hydropower owners, discouraging manufacturers from bringing unvalidated technologies to market. This review and perspective paper examines hydropower trends driving innovation, selected emerging technologies, conventional testing methods, and current U.S. testing capabilities as a case study. We then evaluate the gap between existing capabilities and the needs of low-head powertrains and environmental mitigation measures. Many technologies exceed existing facility flow capacities; in the U.S., the highest combined head–flow capability is limited to 5.66 m3/s, compared with median and 90th-percentile low-head turbine-unit flows of 14.3 and 60 m3/s. To mitigate this gap, we advocate repurposing large, retired, or underused hydraulic infrastructure as full-scale testing facilities to reduce first-adoption risk and support sustainable low-head hydropower deployment.

Tseng, Chien-Yung [Colorado State University, Fort↗
DOE OSTI2025

Generation of a fluorescent short-lifetime oxygen nanosensor by coupling of an exciplex forming dye pair

Typical oxygen-sensitive dyes have lifetimes in the μs-ms regime for sensitive oxygen detection based on molecular quenching. Due to the long triplet-state lifetimes and poor quenching efficiency of these probes, it has been difficult to develop short lifetime probes. We have developed oxygen sensors using a short-lifetime dye (∼30–60 ns) that forms an anthracene-aniline exciplex, which is quenched by molecular oxygen through an excited-state charge transfer mechanism. To achieve measurements in aqueous systems, we have tethered the dyes together via a C3 alkyl linker to facilitate greater exciplex formation at low dye concentration (20 μg mL −1 ) and encapsulated the resulting compound into polymeric nanoparticles to form an aqueous-dispersible short-lifetime oxygen nanosensor. The sensors emit at 420 nm (unfolded dye) and 500 nm (exciplex), and the ratiometric Stern-Volmer Constant is 1.52 ± 0.02 L mol −1 , showing good sensitivity from 0 % to 40 % dissolved oxygen without the tradeoff of a long lifetime needed for direct molecular quenching. In this paper, we characterize this sensor for both lifetime-based measurements using time-correlated single-photon counting and ratiometric intensity-based measurements using the unfolded dye emission as an internal reference peak.

Biological and medical sciences↗
DOE OSTI2021

Measurement of Poly-Si Film Thickness on Textured Surfaces by X-Ray Diffraction in Poly-Si/SiOx Passivating Contacts for Monocrystalline Si Solar Cells

Polycrystalline Silicon on tunneling silicon oxide (poly-Si/SiOx) passivating contacts have shown great potential for the next-generation monocrystalline Si (c-Si) industrial photovoltaic technology. However, these cells typically suffer from strong parasitic absorption in the thick front poly-Si layer, which is designed to reduce metal-induced recombination. In previous work, we demonstrated an improved short-circuit current density, Jsc, by thinning the front poly-Si film in an SF6 plasma using the front metal grids as a self-aligned mask, but the sub - 100 nm thick poly-Si film is difficult to measure on an alkaline textured surface. Conventional optical techniques such as spectroscopic ellipsometry cannot be used due to the high scattering nature of the random pyramids. At poly-Si thicknesses below 50 nm, secondary electron microscopy (SEM) has difficulty distinguishing the poly-Si from the underlying c-Si substrate. Here, we demonstrate X-ray diffraction as an effective method to quantitatively measure the front poly-Si thickness. The thickness calculated from the diffraction peak height of the Si(111) crystallographic plane agrees well with the cross-section SEM analysis and simulations using SunSolve. We show that by thinning the front poly-Si from 200 to 60 nm, Jsc increased by 2.4 mA/cm2, while maintaining the same Voc. This led to an absolute efficiency gain of 1.73%. In addition, we also discuss possible reasons for the premature loss of passivation before the removal of all poly-Si, which prevented an even higher gain in Jsc.

light/electron beam induced current↗
DOE OSTI2022

Setting boundaries on the recipe for a successful RbF post-deposition treatment of CIGS

RbF post-deposition treatments have been explored in the literature for increasing the open-circuit voltage, fill factor, and hence the efficiency of Cu(In,Ga)Se 2 solar cells. However, given the few papers documenting the experimental steps, it was difficult to quickly reproduce the results. This contribution describes some of the optimization steps that led to a successful RbF PDT based on device performance. Here we present results that put boundaries on the temperatures of the RbF cell and the lamp (for sample heating) setpoint. The best recipe for our specific growth process is documented in detail so that others may copy the procedure and possibly arrive at a successful RbF PDT in a reasonable time.

14 SOLAR ENERGY↗
DOE OSTI2022

Effects of Absorber Near-Interface Compensation on Cd(Se,Te) Solar Cell Performance

Arsenic (As) has been shown to be an effective p-type dopant for CdTe, although high performance in As-doped devices remains difficult to achieve. Arsenic is prone to self-compensation in CdTe, as evidenced by the accumulation of dopant atoms in CdTe/Cd(Se,Te) near the interface with MgxZn1-xO (MZO). In this study, we use SCAPS 1D modeling software to investigate the effect of near-interface compensation, helping elucidate loss pathways in present-day As-doped devices and informing future growth directions. We consider three possible results of As accumulation: shallow donors, deep recombination centers, and a thin layer of excess acceptor accumulation. The reduction in near-interface carrier concentration caused by shallow donors is shown to improve open-circuit voltages (VOC), whereas deep levels are detrimental to all performance parameters. The thin charge layer affects capacitance-voltage (CV) measurements by reducing the depletion width while maintaining the same carrier concentration, replicating CV behavior that has been observed in actual devices. These results illustrate the importance of monitoring dopant accumulation within 100 nm of the interface, and suggest that reducing or eliminating the As concentration in this region would be beneficial. An undoped Cd(Se,Te) layer at the interface is suggested as a possible device structure to boost performance.

absorber↗
DOE OSTI2023

Global fire modelling and control attributions based on the ensemble machine learning and satellite observations

Contemporary fire dynamics is one of the most complex and least understood land surface phenomena. Global fire controls related to climate, vegetation, and anthropogenic activity are usually intertwined, and difficult to disentangle in a quantitative way. Here, we leveraged an ensemble of five machine learning (ML) models and multiple satellite-based observations to conduct global fire modeling for three fire metrics (burned area, fire number, and fire size), and quantified driving mechanisms underlying annual fire changes in a spatially resolved manner for the period 2003–2019. Ensemble learning is a meta-approach that combines multiple ML predictions to improve accuracy, robustness, and generalization performance. We found that the optimized ensemble ML well reproduced annual dynamics of global burned area (R 2 = 0.90, P < 0.001), total fire numbers (R 2 = 0.86, P < 0.001), and averaged fire size (R 2 = 0.70, P < 0.001). Additionally, the ensemble ML captured key spatial patterns of multi-year mean magnitudes, annual variabilities, anomalies, and trends for different fire metrics. Our ML-based fire attributions further highlighted the dominant role of enhanced anthropogenic activity in reducing global burned area (–1.9 Mha/yr, P < 0.01), followed by climate control (–1.3 Mha/yr, P < 0.01) and insignificant positive vegetation control (0.4 Mha/yr, P = 0.60). Spatially, climate dominated a much larger burned area (53.7%) than human (23.4%) or vegetation control (22.9%); however, the counteracting effects from regional wetting and drying trends weakened the net climate impacts on global burned area. The fire number and fire size exhibited similar spatial control patterns with burned area; globally, however, fire number tended to be more affected by climate while fire size more influenced by human activities. Overall, our study confirmed the feasibility and efficiency of ensemble ML in global fire modeling and subsequent control attributions, providing a better understanding of contemporary fire regimes and contributing to robust fire projections in a changing environment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Thermodynamics, local structure, and transport of protons in triple-conducing oxide, BaCo 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3-δ (BCFZY4411)

Triple-conducting oxides (TCOs) are an emerging class of mixed ionic and electronically conducting materials that show great promise for oxygen reduction/oxygen evolution (ORR/OER) electrocatalysis—primarily in high-temperature ceramic electrochemical cells— but also in aqueous alkaline environments. Their high activity is attributed, at least in part, to their ability to incorporate and transport three mobile charge carriers: protons, oxygen vacancies, and electron-holes Despite their promise, fundamental studies of TCOs are challenging, as transport dynamics from three charge carriers cannot be fully disentangled via traditional electrical measurement techniques. Characterizing proton dynamics in TCOs is particularly difficult as protons are generally the minority carrier, and their conduction response is typically obscured by the oxygen vacancies and electron holes. Here, we demonstrate successful isolation of the proton behavior in an archetypal TCO, BaCo 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3-δ (BCFZY4411), using a combination of non-electrical techniques. We determine proton uptake and oxygen non-stoichiometry (δ) using thermogravimetric analysis (TGA). X-ray absorption near edge structure (XANES) and neutron diffraction (ND) are used to validate the oxidation state of Co and the δ values obtained through TGA. We apply 1H solid-state magic-angle-spinning (MAS) nuclear magnetic resonance (NMR) to provide insights into local structure, dynamics, and proton kinetics. Finally, the proton transport properties are further quantified using tracer isotope exchange with time-of-flight secondary ion mass spectrometry (ToF-SIMS). Despite the very low proton concentrations in BCFZY4411 (<0.2% under most conditions), our analysis suggests that the oxygen Manuscript File Click here to view linked References 2 reduction and evolution reactions are nevertheless limited by the oxygen ion kinetics (e.g., oxygen surface exchange) rather than the proton kinetics at the reduced operating temperatures (<500 °C) that are targeted for electrochemical cell applications. These findings provide a comprehensive understanding of proton behavior in BCFZY4411 and pave the way for advancing the fundamental study of TCOs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Phase-sensitive γ-encoded recoupling of heteronuclear dipolar interactions and 1 H chemical shift anisotropy

γ-encoded recoupling sequences are known to produce strong amplitude modulations that lead to sharp doublets when Fourier transformed. These doublets depend very little on the recoupled tensor asymmetry and thus enable for the straightforward determination of dynamic order parameters. It can, however, be difficult to measure small anisotropies, or small order parameters, using such sequences; the resonances from the doublet may overlap with each other, or with the zero-frequency glitch. This limitation has prevented the widespread use of 1 H chemical shift anisotropy (CSA) for the measurement of dynamics, particularly for CH protons which typically have CSAs of only a few ppm when immobile. In this work, we introduce a simple modification to the traditional 1 H CSA and proton-detected local field pulse sequences that enables the acquisition of a hypercomplex dataset and the removal of the uncorrelated magnetization that results in the zero-frequency glitch. These new sequences then yield a frequency shift in the indirect dimension, rather than a splitting, which is easily identifiable even in cases of weak interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Synchrotron infrared nano-spectroscopy and -imaging

Infrared (IR) spectroscopy has evolved into a powerful analytical technique to probe molecular and lattice vibrations, low-energy electronic excitations and correlations, and related collective surface plasmon, phonon, or other polaritonic resonances. In combination with scanning probe microscopy, near-field infrared nano-spectroscopy and -imaging techniques have recently emerged as a frontier in imaging science, enabling the study of complex heterogeneous materials with simultaneous nanoscale spatial resolution and chemical and quantum state spectroscopic specificity. Here, we describe synchrotron infrared nano-spectroscopy (SINS), which takes advantage of the low-noise, broadband, high spectral irradiance, and coherence of synchrotron infrared radiation for near-field infrared measurements across the mid- to far-infrared with nanometer spatial resolution. This powerful combination provides a qualitatively new form of broadband spatio-spectral analysis of nanoscale, mesoscale, and surface phenomena that were previously difficult to study with IR techniques, or even any form of micro-spectroscopy in general. We review the development of SINS, describe its technical implementations, and highlight selected examples representative of the rapidly growing range of applications in physics, chemistry, biology, materials science, geology, and atmospheric and space sciences.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

The surface chemistry of cuprous oxide

The chemical and electronic properties of copper combined with its large natural abundance lend this material to impact a wide range of technological applications, including heterogeneous catalysis. The reactivity of copper in its Cu 1+ oxidation state makes this specific configuration relevant in various chemical reactions, but the facile redox properties of copper make the isolation of individual states for fundamental studies difficult. Here, in this study, we review three Cu 2 O model systems used to study the interaction of Cu 1+ with small molecules making use of surface science techniques: Cu 2 O/Cu(111), thin polycrystalline Cu 2 O films on Cu foil, and bulk Cu 2 O crystals. Advantages and disadvantages of each system are discussed and exemplified through case studies of chemical adsorption and reactivity studies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Alternative Ratemaking in the US: A Prerequisite for Grid Modernization or an Unwarranted Shift of Risk to Customers?

With increasing frequency, investor-owned electric utilities are requesting preferred cost recovery for "grid modernization" in multiple forms, from multi-year rate plans to riders. Utilities' claims that massive grid investment is necessary, and that exceptional investment requires exceptional cost recovery, are typically accepted by policymakers with little challenge. It is difficult for policymakers to resist the siren call of grid modernization's perceived outcomes, from improved reliability and resilience to reduced risks to safety and new customer technology adoption (electric vehicles, distributed energy resources, and more). This paper provides a contrarian viewpoint that is virtually absent as policymakers consider alternative ratemaking practices. It introduces the possibility that excess grid investment in the name of modernization is not only possible, and economically harmful, but has already occurred, encouraged by alternative ratemaking. It provides examples of common grid modernization expenditures the authors have identified as cost-ineffective in the course of their work. It also describes traditional grid planning practices with proven ability to address changing requirements over time, calling into question the need for exceptional grid modernization investment plans. Most important, the paper explains the moral hazard inherent in alternative ratemaking, and the fundamental shift in ratemaking risks and responsibilities from utilities to customers that results. The perspectives this paper presents are critical for policymakers to understand before adopting, extending, or expanding alternative ratemaking practices in their respective jurisdictions.

ENERGY PLANNING, POLICY, AND ECONOMY,POWER TRANSMI↗