Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “device engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Isolation of Single Donors in ZnO

The shallow donor in zinc oxide (ZnO) is a promising semiconductor spin qubit with optical access. Single indium donors are isolated in a commercial ZnO substrate using plasma focused ion beam (PFIB) milling. Quantum emitters are identified optically by spatial and frequency filtering. The indium donor assignment is based on the optical bound exciton transition energy and magnetic dependence. The emission stability of these single donors in terms of both intensity and frequency, alongside their transition linewidths less than twice the lifetime limit, highlight the promise of single In donors as optically accessible spin qubits. Here, the optical stability of single donors after FIB fabrication is promising for optical device integration required for scalable quantum technologies based on single donors in direct band gap semiconductors.

42 ENGINEERING↗
DOE OSTI2022

Demonstration of Spectral Selectivity of Efficient and Ultrafast GaN/AlGaN-Based Metal–Semiconductor–Metal Ultraviolet Photodiodes

Efficient and ultrafast (aluminum)-gallium-nitride-based metal-semiconductor-metal (Al x )Ga 1–x N ultraviolet photodiodes were implemented to investigate the spectral properties of GaN/AlGaN-based photodetectors. Al composition of the GaN templates were varied from 0-% to 30% to demonstrate the impact of Al mole fraction on the cutoff wavelength of these UV photodiodes. Asymmetric metal contact electrodes were fabricated to optimize the external quantum efficiency without compromising their ultrafast photoresponse. Here, the best performing devices exhibited a peak response of 4 V and an oscilloscope limited temporal pulse width of 61 ps at a 20-V bias with a peak spectral responsivity of 36.5 mA/W at 280 nm.

42 ENGINEERING↗
DOE OSTI2022

Single DC Source Based Cascaded Multilevel Inverter

The objective of this project is to develop a high-efficiency solid-state transformer that converts a fixed DC voltage to a medium-voltage AC for utility distribution network connections without having the conventional low-frequency bulky transformers and switch gears. The initial target of 99% efficiency was achieved with the use of wide bandgap semiconductor devices using a proposal novel multilevel inverter. The medium-voltage was successfully tested at 7.2/12.47 kV phase/line voltage level for a 100-kW three-phase inverter.

14 SOLAR ENERGY↗
DOE OSTI2024

ASIC Scoping Study Final Report

This report documents the results and findings of a one-year scoping study investigating multichannel readout application specific integrated circuits (ASICs) for interfacing to, and processing data from, silicon photomultiplier (SiPM) arrays. We document ASIC desired and required specifications for four applications supporting national security mission areas: neutron radiography, associated particle imaging, and two versions of kinematic neutron imaging cameras. While each application has a few unique requirements that stress capability, there is generally good agreement among most. Two recently developed ASIC devices were evaluated in a system-like configuration by interfacing these to scintillator crystals exposed to gamma and neutron sources. The 64-channel ORNL device delivered functional capability while meeting most mission requirements for neutron radiography. The Nalu Scientific device, a 32-channel full waveform digitizer, did not demonstrate reliable neutron / gamma separation but it is unclear if this was an ASIC issue or problems with test setup or firmware. A literature survey of other commercial and academic ASICs was undertaken to with the conclusion that existing devices do not meet all requirements.

42 ENGINEERING↗
DOE OSTI2025

Materials for Energy Management across the Electromagnetic Spectrum (MEMES) (LDRD Report)

Electrification of the United States has been a major driver of economic growth, powering industrialization, modern manufacturing, and the digital economy. Today, further economic and environmental benefits can be realized by improving the energy efficiency of the technologies we have come to rely on. This project focused on enhancing the energy efficiency of two cornerstone technologies of modern society: electronic displays and building climatization. While these two technologies operate in different parts of the electromagnetic spectrum (the visible and infrared, respectively), they share a common potential technological solution: electrically-driven displays that change reflectivity. In this work, we developed the first multipixel multicolor reflective display that achieves multi-colorization with fast-changing structural color. In the course of this demonstration, we quantified the structural changes that occur across different time and length scales and resolved device sealing issues, enabling operation of these devices over months (as opposed to days previously). We furthermore developed two reflectivity changing devices in the infrared and demonstrated how these technologies can be used to reduce climatization demands for both smart window and smart wall technologies. Implementing such a device in a scaled down mock room resulted in 10 degree Celsius change.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Design and Development of a Robotic Exoskeleton Device for use in Glove Boxes - 20374

Glovebox operators in nuclear facilities often operate under radioactive environment and typically perform monotonous, dull and repetitive work. This can result in muscle fatigue leading to increased levels of accidents. Current research work aims in assisting the glovebox operators by designing a novel upper limb exoskeleton device to reduce injuries and increase worker efficiency. Almost none of the commercially available hand and upper body exoskeletons are directly suitable for use in gloveboxes. This explains the novelty of the present work in developing a wearable powered robotic exoskeleton device. The device consists of electronics, motors and spring systems mounted on adjustable plates and is supported by a stationary frame behind the worker. The device is intended to be portable and adjustable according to the operator height. The elbow has a flexion movement assisted with motor control by way of a Bowden cable system. The system is floated on a spring and pulley combination that allows for extra safety and smoothness of operation. The end points are fixed near the pivot points to help minimize unwanted movement/torque. The extension movement of the upper and lower arm are assisted by gravity and a counter spring. The shoulder and upper arm movement are held in a neutral position with a spring system for counter balance allowing small movements within the glovebox. This initial concept considers only the vertical movement of the arm. The abduction and adduction movement will not be assisted or impeded by the over shoulder plate or at the forearm plate allowing for full range of motion. Several glovebox aspects such as the level of task assistance, ergonomic design, minimum hindrance in dexterity/operator movements and tear resistance for hazardous safety reasons will be considered in the design of the exoskeleton. Computer models will be simulated to test the load levels and stress conditions on the exoskeleton to enhance the designs. The exoskeleton focusses on major muscular involvement reduction through weight offset and active assistance with minimal parts and hence the device is derived with several joint links and contains both passive and active joints. The paper details the various stages in the design development and prototype testing of the exoskeleton device. Upon successful prototype device development, human testing will be conducted in a replica of the SRS-235F hot cell facility constructed at FIU-ARC. The final stage of the project will be potential testing/deployment of the exoskeleton device in one of the glovebox facilities in Savannah River Nuclear Waste site. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Nonlinear Topological Photonics: Capturing Nonlinear Dynamics and Optical Thermodynamics

Combining multiple optical resonators or engineering dispersion of complex media has provided an effective method for demonstrating topological physics controlling photons in unprecedented ways such as unidirectional light propagation and spatially localized modes between an interface or on a corner. Further, adding nonlinear responses to those topological photonic systems has enabled achieving diverse phases of photons in both space and time, allowing for more functionalities in photonic devices that provide a new playground for studying dynamic features of nonlinear topological systems. However, most methods for describing nonlinear topological photonic systems rely on linear topological theories, making it challenging to accurately characterize the topology of nonlinear systems. Thus, substantial efforts have focused on rigorously describing nonlinear topological phases and developing effective tools to analyze nonlinear topological effects. Meanwhile, coupled multimode optical waveguides with nonlinear dynamic responses provide an excellent platform for the statistical description of photons, opening a new paradigm called “optical thermodynamics”. This review will introduce the basic concepts of nonlinear topological photonics and the recent development of theoretical approaches focusing on data-driven approaches for creating phase diagrams as well as the spectral localizer framework and the pseudospectrum method for understanding optical nonlinearities in topological systems. In addition, the new concept of optical thermodynamics will be introduced with some recent theoretical works.

Topological photonics↗
DOE OSTI2025

Correlation control of the Mott transition in LaTiO 3 /SrTiO 3 heterostructures

The Mott metal-insulator transition arises from electron-electron interactions determined by the ratio of Coulomb to kinetic energy scales (U/t). While temperature, pressure, and doping can induce Mott transitions, direct control of U in solid-state systems remains largely unexplored, particularly in the inhomogeneous environments of emerging neuromorphic devices, where conductive filaments create complex gradients of local properties. Here we show that interface-induced screening can continuously tune the electron-electron interaction strength U to drive an isothermal Mott transition. Using thickness-graded LaTiO3/SrTiO3 heterostructures, we used diffraction and photoemission spectroscopy to reveal a continuous, isothermal quantum phase transition from a Fermi liquid quasiparticle with incoherent excitations to a Mott insulator with Hubbard bands. The primary determinant of the transition is the enhanced local screening environment, which directly influences the interaction strength U, driving the system metallic. This demonstrates that interface engineering of the local screening environment provides a promising approach to manipulate Mott physics through correlation control, beyond traditional bandwidth or filling approaches.

Electronic and spintronic devices↗
DOE OSTI2021

Modulation and Modeling of Three-Dimensional Nanowire Assemblies Targeting Gas Sensors with High Response and Reliability

Despite improved sensitivity, simple downsizing of gas-sensing components to randomly arranged nanostructures often faces challenges associated with unpredictable electrical conduction pathways. In the present study, controlled fabrication of three-dimensional (3D) metal oxide nanowire networks is demonstrated that can greatly improve both signal stability and sensor response compared to random nanowire arrays. For example, the highest ever reported H 2 S gas response value, and a 5 times lower relative standard deviation of baseline resistance than that of random nanowires assemblies, are achieved with the ordered 3D nanowire network. Systematic engineering of 3D geometries and their modeling, utilizing equivalent circuit components, provide additional insights into the electrical conduction and gas-sensing response of 3D assemblies, revealing the critical importance of wire-to-wire junction points and their arrangement. Here these findings suggest new design rules for both enhanced performance and reliability of chemical sensors, which may also be extended to other devices based on nanoscale building blocks.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A 0.2–2 GHz Time-Interleaved Multistage Switched-Capacitor Delay Element Achieving 2.55–448.6 ns Programmable Delay Range and 330 ns/mm 2 Area Efficiency

Simulation of radar returns, full-duplex systems, and signal repeaters require hundreds of ns of programmable broadband radio frequency (RF) delay in the signal path to simulate large distances in the case of radar returns, for signal cancellation in full-duplex, and for isolation from reflections in signal repeaters. However, programmable broadband RF delay has been limited to ones of ns due to challenges in miniaturization with low loss and low power consumption. In this work, we present a 0.2–2 GHz digitally programmable RF delay element based on a time-interleaved multistage switched-capacitor (TIMS-SC) approach. The proposed approach enables hundreds of ns of broadband RF delay by employing sample time expansion in multiple stages of switched-capacitor storage elements. Further, the delay element was implemented in a 45 nm SOI CMOS process and achieves a 2.55–448.6 ns programmable delay range with < 0.12% delay variation across 1.8 GHz of bandwidth at maximum delay, 2.42 ns programmable delay steps, and 330 ns/mm 2 area efficiency. Through the proposed approach, the device shows minimal delay change across a -40 °C to 85 °C temperature range and < 0.25 dB gain variation across delay settings. The device achieves 26 dB gain, 7.4 dB noise figure, and consumes 74 mW from a 1 V supply with an active area of 1.36 mm 2 .

42 ENGINEERING↗
DOE OSTI2026

Advanced Micro Combined Heat and Power Device

U.S. buildings account for approximately 40% of total U.S. energy consumption and 75% of electricity use, emphasizing the need for efficient, resilient, and secure energy solutions. Micro-combined heat and power (micro-CHP) systems provide an effective approach by simultaneously generating electricity and recovering waste heat for thermal use. However, current commercial micro-CHPs face challenges in achieving higher efficiency, lower emissions, and reduced cost. To address these limitations, a novel micro-CHP prototype powered by a unique opposed-piston four-stroke (OP4S) engine was developed. The OP4S features a simplified, low-cost design with reduced heat losses and dual-piston operation that enables higher thermal efficiency. Experimental results demonstrated up to 35.2% AC electrical efficiency under lean combustion, surpassing the best-performing ICE-based micro-CHPs reported publicly. In addition, the micro-CHP enables a total CHP efficiency exceeding 93%. The prototype operates reliably for over 600 hours, providing flexible and efficient thermal and electrical outputs. This novel OP4S-based micro-CHP offers a resilient, low-cost, and energy-efficient solution suitable for residential, light commercial, and remote community applications across diverse climate zones.

Gao, Zhiming [ORNL] (ORCID:0000000271397995)↗
DOE OSTI2024

PLC Vulnerabilities and Mitigations

Programmable Logic Controllers (PLCs) are used extensively in many high-importance industrial and nonindustrial settings including controlling elevators, manufacturing machines, and utility facilities such as power and natural gas, however cybersecurity protection for them has been neglected. Within recent years, PLCs have been put under more security scrutiny and experts have advocated for changes from the addition of protocol encryption and network segmentation to intrusion detection systems on the PLCs themselves. While PLC security is critical, a large portion of the PLCs available today will never receive these changes due to being legacy or the difficulty of overhauling the security on existing systems. Due to the infeasibility of applying many recommended security measures towards currently available machines, we aim to provide realistic and affordable best practices for hardening PLCs. We will first conduct security analysis and consider attack vectors within our target PLC. Once we’ve analyzed the device’s security, we will evaluate a variety of mitigation methods and create guidelines to effectively reduce the threat posed by PLC attacks with minimal disruption to operations.

42 ENGINEERING↗
DOE OSTI2025

Optimal Control of an Oscillating Surge Wave Energy Converter

During this project, we experimentally investigated the hydrodynamics and performance of a laboratory-scale oscillating surge wave energy converter (OSWEC).We looked at how flap buoyancy and driveline losses (primarily in the form of stiction) affected the dynamics and performance of the device. In addition, we assessed the influence of flap profile (rounded vs. square edges) on OSWEC hydrodynamics. Through this, we were able to develop a deeper understanding of OSWEC performance and provide guidance on strategies to counteract artifacts that may be present in laboratory models, but are absent in field-scale devices. To do this, we tested a laboratory-scale OSWEC in the Sea Wave Environmental Lab (SWEL) wave tank at the National Renewable Energy Laboratory (NREL). We ran several types of experiments to investigate the hydrodynamics and performance of the device. Overall, we achieved the overall goal of experimentally investigating the hydrodynamics and performance of this device. We discovered important and unexpected trends in performance, and collected time-resolved data to help us further investigate the underlying hydrodynamics responsible for these trends. In addition, we are currently using the time-resolved data from these experiments to build data-driven models of the dynamics, which can in turn be used to inform data-driven model predictive control of this device and address this objective in the future.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

3D high-fidelity automated neutronics guided optimization of fusion blanket designs

The compact Fusion Pilot Plant (FPP) is defined in the recent National Academies of Sciences, Engineering, and Medicine report as the next step of fusion energy demonstration with a $50$ MWe peak net electricity production, $Q_e$ greater than $1$, and at least $3$ hours of continuous operation. This fusion pilot plant will be a test bed enabling materials, designs, and fuel management assessment, and it will represent an engineering challenge because of its high-fusion power and compact design targets. Previous reactor data is limited to experiments operating in different design space ranges. Therefore, design iterations and assessments should rely on high-fidelity first-principle theoretical and computational models. The high-fidelity integrated modeling of the plasma is a fundamental part of fusion energy research. However, the whole device modeling is often neglected, utilizing low-fidelity, system-level analysis. Recently, the need for high-fidelity multi-physics modeling was recognized, resulting in a selection of integrated tools. Further, autonomous design optimization requires a streamlined framework that perturbs the design point, reruns the analysis, and examines the outputs. However, high-fidelity analysis requires complex geometry specification that is difficult to perturb. This work presents the parametric CAD generation tool TRACER and a new neutronic workflow. TRACER allows the perturbation of the geometry representation, creating geometry files ready for further analysis. The streamlined neutronic workflow allows efficient and accurate calculations. The two new tools coupled together were used to perform a 3D high-fidelity multi-objective, multi-input optimization of an "ARC Class" compact tokamak design. The workflow was driven by an optimization driver for full automation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Aligning lithium metal battery research and development across academia and industry

Successful integration of metallic lithium anodes into secondary batteries could enhance energy density and enable new forms of electrified transportation. However, the outlook for widespread lithium metal adoption in energy storage devices remains mixed. This comes in part from existing gaps in our understanding of the relationships connecting the initial state of lithium, its evolution with cycling, and end-of-life state. It remains important to develop standardized protocols for material and cell characterization, cycling performance, safety, and recycling procedures for lithium metal-based batteries. In February 2023 a cohort of scientists and engineers from academia, national laboratories, and industry gathered to converge on a list of critical challenges and action items to provide better understanding of lithium metal evolution and to enhance academic, governmental, and industrial partnerships to address these challenges. Here, we highlight the major discussion topics revolving around the manufacturing of lithium metal, its related metrology and integration into battery form factors, and best practices testing its electrochemical performance relevant to automotive applications. We introduce a power-controlled discharge testing protocol for research and development cells, in alignment between major automotive stakeholders, that may reveal lithium metal battery dynamics closer to practical driving behavior.

25 ENERGY STORAGE↗
DOE OSTI2025

Probing the Kitaev honeycomb model on a neutral-atom quantum computer

Quantum simulations of many-body systems are among the most promising applications of quantum computers. In particular, models based on strongly correlated fermions are central to our understanding of quantum chemistry and materials problems, and can lead to exotic, topological phases of matter. However, owing to the non-local nature of fermions, such models are challenging to simulate with qubit devices. Here we realize a digital quantum simulation architecture for two-dimensional fermionic systems based on reconfigurable atom arrays. We utilize a fermion-to-qubit mapping based on Kitaev’s model on a honeycomb lattice, in which fermionic statistics are encoded using long-range entangled states. We prepare these states efficiently using measurement and feedforward, realize subsequent fermionic evolution through Floquet engineering with tunable entangling gates interspersed with atom rearrangement, and improve results with built-in error detection. Leveraging this fermion description of the Kitaev spin model, we efficiently prepare topological states across its complex phase diagram and verify the non-Abelian spin-liquid phase by evaluating an odd Chern number. We further explore this two-dimensional fermion system by realizing tunable dynamics and directly probing fermion exchange statistics. Finally, we simulate strong interactions and study the dynamics of the Fermi–Hubbard model on a square lattice. These results pave the way for digital quantum simulations of complex fermionic systems for materials science, chemistry and high-energy physics.

atomic and molecular physics↗
DOE OSTI2024

Maximum Switching Throughput Density Estimator

SAND2024-11125O The Maximum Switching Throughput Density Estimator software performs a simple analysis that estimates the maximum logic switching throughput density that’s achieved in various CMOS technology nodes on the International Roadmap for Devices and Systems. This software utilizes simple device models and optimization techniques, performing a simple sweep over a range of possible logic supply voltages, and analytically calculating the maximum switching frequency for the given logic voltage that meets the power density constraint. It does this by using simple models of power dissipation in conventional and fully adiabatic switching. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Frank, Michael↗
DOE OSTI2021

Interface-Driven Chiral Magnetism in Ultrathin Metallic Ferromagnets: Towards Skyrmion Spintronics

Magnetic skyrmions are localized chiral magnetic textures in the form of nanoscale vortices or bubbles that are topologically protected from being ‘unwound’. Their topological nature gives rise to rich behaviors including ordered lattice formation, emergent electrodynamics and robust current-driven displacement at remarkably low current densities. However, magnetic skyrmions have so far been restricted to just a few materials and observed only at low temperatures, limiting the experimental accessibility and technological application of these unique topological objects. This project aimed to realize magnetic skyrmions at room temperature in a new class of engineered chiral ferromagnets that exploit broken mirror symmetry at interfaces to generate helical magnetic order. Ultrathin magnetic heterostructures were engineered and patterned into laterally-confined nanostructures in which skyrmions were stabilized, manipulated, and detected for the first time under ambient conditions. Static and dynamic properties were examined using advanced x-ray imaging to provide a fundamental understanding of topological magnetic phases. The interactions between magnetic skyrmions and electron charge and spin currents were studied to identify fundamental new physics and enable device applications. These experimental studies, supported by detailed modeling, will help launch a new subfield of skyrmion-based spintronics in which individual skyrmions can be used to encode, store, and transport information in high-performance, low power memory and logic devices.

36 MATERIALS SCIENCE↗