Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data predictive control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Peak-Seeking Optimization of Trim for Reduced Fuel Consumption: Architecture and Performance Predictions

A peak-seeking control approach for real-time trim configuration optimization for reduced fuel consumption has been developed by researchers at the National Aeronautics and Space Administration (NASA) Dryden Flight Research Center to address the goals of the NASA Environmentally Responsible Aviation project to reduce fuel burn and emissions. The peak-seeking control approach is based on a steepest-descent algorithm using a time-varying Kalman filter to estimate the gradient of a performance function of fuel flow versus control surface positions. In real-time operation, deflections of symmetric ailerons, trailing-edge flaps, and leading-edge flaps of an FA-18 airplane (McDonnell Douglas, now The Boeing Company, Chicago, Illinois) are controlled for optimization of fuel flow. This presentation presents the design and integration of this peak-seeking controller on a modified NASA FA-18 airplane with research flight control computers. A research flight was performed to collect data to build a realistic model of the performance function and characterize measurement noise. This model was then implemented into a nonlinear six-degree-of-freedom FA-18 simulation along with the peak-seeking control algorithm. With the goal of eventual flight tests, the algorithm was first evaluated in the improved simulation environment. Results from the simulation predict good convergence on minimum fuel flow with a 2.5-percent reduction in fuel flow relative to the baseline trim of the aircraft.

peak-seeking↗
NASA NTRS2016

Assessment of the Uniqueness of Wind Tunnel Strain-Gage Balance Load Predictions

A new test was developed to assess the uniqueness of wind tunnel strain-gage balance load predictions that are obtained from regression models of calibration data. The test helps balance users to gain confidence in load predictions of non-traditional balance designs. It also makes it possible to better evaluate load predictions of traditional balances that are not used as originally intended. The test works for both the Iterative and Non-Iterative Methods that are used in the aerospace testing community for the prediction of balance loads. It is based on the hypothesis that the total number of independently applied balance load components must always match the total number of independently measured bridge outputs or bridge output combinations. This hypothesis is supported by a control volume analysis of the inputs and outputs of a strain-gage balance. It is concluded from the control volume analysis that the loads and bridge outputs of a balance calibration data set must separately be tested for linear independence because it cannot always be guaranteed that a linearly independent load component set will result in linearly independent bridge output measurements. Simple linear math models for the loads and bridge outputs in combination with the variance inflation factor are used to test for linear independence. A highly unique and reversible mapping between the applied load component set and the measured bridge output set is guaranteed to exist if the maximum variance inflation factor of both sets is less than the literature recommended threshold of five. Data from the calibration of a six{component force balance is used to illustrate the application of the new test to real-world data.

strain-gage balance↗
DOE OSTI2026

Revolutionizing Energy Storage: AI, Automation, and Advanced Modeling as Catalysts for Next-Generation Breakthroughs

The Presidential Symposium (PRES) at the 2025 Fall Meeting, hosted by the President’s Office and Energy and Fuels Division, American Chemical Society (ACS) in Washington, DC, brought together a diverse group of chemists, engineers, and materials scientists working in battery materials & systems, automation and artificial intelligence from academia, industry, and national laboratories. The accelerating demand for high-performance, scalable, and sustainable energy storage has catalyzed a paradigm shift in how materials are dis-covered, devices are engineered, and systems are optimized. This Presidential Symposium, entitled “Revolutionizing Energy Storage: AI, Automation, and Advanced Modeling Driving Next-Gen Breakthroughs”, brings together global leaders to unveil transformative strategies anchored in the AAA framework: Artificial Intelligence, Automation, and Advanced Modeling. Artificial Intelligence is redefining the frontiers of energy storage by enabling predictive design, real-time optimization, and intelligent control across diverse chemistries and architectures. Automation is streamlining the synthesis, characterization, and testing of battery materials, dramatically accelerating innovation cycles and unlocking scalable solutions for grid and mobility applications. Advanced Modeling, spanning atomic to system-level scales, provides unprecedented insight into electrochemical dynamics, degradation pathways, and thermal behavior, particularly when coupled with physics-informed machine learning and digital twin technologies. Digital twins, in turn, leverage the AAA framework by integrating real-time data, physics-based models, and AI predictions into dynamic virtual replicas, enabling proactive diagnostics, optimization, and system resilience. Together, these synergistic pillars are not only re-shaping the scientific landscape but also forging a new era of reproducible, data-driven, and resilient energy storage innovation. In conclusion, this symposium marks a pivotal moment in the convergence of computational intelligence and experimental rigor, charting the course for next-generation breakthroughs in lithium-ion, solid-state, and flow battery technologies.

Artificial Intelligence (AI)↗
NASA NTRS2018

Airspace Technology Demonstration 2 (ATD-2) Technology Description Document (TDD)

This Technology Description Document (TDD) provides an overview of the technology for the Phase 1 Baseline Integrated Arrival, Departure, and Surface (IADS) prototype system of the National Aeronautics and Space Administration's (NASA) Airspace Technology Demonstration 2 (ATD-2) project, to be demonstrated beginning in 2017 at Charlotte Douglas International Airport (CLT). Development, integration, and field demonstration of relevant technologies of the IADS system directly address recommendations made by the Next Generation Air Transportation System (NextGen) Integration Working Group (NIWG) on Surface and Data Sharing and the Surface Collaborative Decision Making (Surface CDM) concept of operations developed jointly by the Federal Aviation Administration (FAA) and aviation industry partners. NASA is developing the IADS traffic management system under the ATD-2 project in coordination with the FAA, flight operators, CLT airport, and the National Air Traffic Controllers Association (NATCA). The primary goal of ATD-2 is to improve the predictability and operational efficiency of the air traffic system in metroplex environments, through the enhancement, development, and integration of the nation's most advanced and sophisticated arrival, departure, and surface prediction, scheduling, and management systems. The ATD-2 project is a 5-year research activity beginning in 2015 and extending through 2020. The Phase 1 Baseline IADS capability resulting from the ATD-2 research will be demonstrated at the CLT airport beginning in 2017. Phase 1 will provide the initial demonstration of the integrated system with strategic and tactical scheduling, tactical departure scheduling to an en route meter point, and an early implementation prototype of a Terminal Flight Data Manager (TFDM) Electronic Flight Data (EFD) system. The strategic surface scheduling element of the capability is consistent with the Surface CDM Concept of Operations published in 2014 by the FAA Surface Operations Directorate.

integrated arrival↗
NASA NTRS1982

Analytical prediction of the interior noise for cylindrical models of aircraft fuselages for prescribed exterior noise fields. Phase 2: Models for sidewall trim, stiffened structures and cabin acoustics with floor partition

An airplane interior noise prediction model is developed to determine the important parameters associated with sound transmission into the interiors of airplanes, and to identify apropriate noise control methods. Models for stiffened structures, and cabin acoustics with floor partition are developed. Validation studies are undertaken using three test articles: a ring stringer stiffened cylinder, an unstiffened cylinder with floor partition, and ring stringer stiffened cylinder with floor partition and sidewall trim. The noise reductions of the three test articles are computed using the heoretical models and compared to measured values. A statistical analysis of the comparison data indicates that there is no bias in the predictions although a substantial random error exists so that a discrepancy of more than five or six dB can be expected for about one out of three predictions.

Pope, L. D.↗
DOE OSTI2025

Part distortion monitoring in additive manufacturing using machining

In additive manufacturing, accumulation of residual stresses can result in severe part distortion from the desired preform shape. Current methods for in-situ part distortion monitoring in additive manufacturing typically require expensive sensors, or capital equipment, and require time-consuming post-processing to understand the shape deviation. This paper presents an in-situ method, in the context of hybrid manufacturing, for part distortion detection using machining of additively manufactured parts. As a surrogate, three test artifacts were used to represent different distorted geometries. The tool axis positions from the machine tool controller and the cutting power were monitored during a facing operation. Cutting power data was used to detect the tool entry and exit in the workpiece using a novel approach with power standard deviation metric. The workpiece geometry and distorted configuration was subsequently predicted for positional and rotational deviations to within 2 mm accuracy using synchronized tool position data with cutting power. The proposed method can be used in a hybrid (additive and subtractive) machine tool to periodically check part distortion in the additive build. The method is applicable for any additive process and is low-cost and computationally inexpensive.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Towards fast, accurate predictions of RF simulations via data-driven modeling: Forward and lateral models

Three machine learning techniques (multilayer perceptron, random forest, and Gaussian process) provide fast surrogate models for lower hybrid current drive (LHCD) simulations. A single GENRAY/CQL3D simulation without radial diffusion of fast electrons requires several minutes of wall-clock time to complete, which is acceptable for many purposes, but too slow for integrated modeling and real-time control applications. More accurate simulations with fast electron diffusion are even slower, requiring multiple hours of run time with parallel processing. The machine learning models use a database of 16,000+ GEN-RAY/CQL3D simulations for training, validation, and testing. Latin hypercube sampling methods implemented in πScope ensure that the database covers the range of 9 input parameters (n e0 , T e0 , I p , B t , R 0 , n ∥︀ , Z e f f , V loop , P LHCD ) with sufficient density in all regions of parameter space. The surrogate models reduce the computation time from minutes-hours to ms with high accuracy across the input parameter space. Data-driven surrogate models also allow for solving inverse and “lateral” problems. A surrogate model for the inverse problem maps from a desired current drive or power deposition profile to a set of input parameters that would result in such a profile, while a surrogate model for the lateral problem maps from a measured experimental quantity such as hard x-ray emission to a current drive or power deposition profile. In conclusion, the πScope database creation workflow is flexible and applicable to other RF simulation codes such as TORIC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

N 2 vibrational excitation in atmospheric pressure ns pulse and RF plasma jets

Time-resolved N 2 vibrational temperature and translational–rotational temperature in quasi-two-dimensional atmospheric pressure plasma jets sustained by ns pulse and RF discharges in nitrogen/noble gas mixtures are measured by the broadband vibrational Coherent Anti-Stokes Raman Scattering (CARS) . The results indicate a much stronger vibrational excitation in the RF plasma jet, due to the lower reduced electric field and higher discharge power. In a ns pulse discharge in N 2 /He, N 2 vibrational temperature is significantly lower compared to that in N 2 /Ar, due to the more rapid vibration–translation (V–T) relaxation of nitrogen by helium atoms. In the RF plasma jets in N 2 /Ne and N 2 /Ar, the vibrational excitation increases considerably as the nitrogen fraction in the mixture is reduced. The experimental data in the RF plasma jet in N 2 /Ar jet are compared with the kinetic modeling predictions. The results indicate that nitrogen vibrational excitation in N 2 /Ar plasma jets with a small N 2 fraction in the mixture (several percent) is controlled primarily by electron impact, anharmonic vibration–vibration (V–V) pumping, and V–T relaxation by N atoms. In comparison, V–V energy transfer from the vibrationally excited molecules in the first excited electronic state, N 2 (A 3 Σ u + , v), which are generated primarily by the energy transfer from the metastable Ar atoms, has a minor effect on the vibrational populations of the ground electronic state, N 2 (X 1 Σ g + , v). Although the discharge energy fraction going to electronic excitation is significant, the predicted quasi-steady-state N 2 (A 3 Σ u + ) number density, controlled by the energy pooling and quenching by N atoms, remains relatively low. Because of this, the net rate of N 2 (X 1 Σ g + ) vibrational excitation by the V–V energy transfer from N 2 (A 3 Σ u + ) is much lower compared to that by the direct electron impact. Furthermore, the results show that atmospheric pressure RF plasma jets can be used as sources of highly vibrationally excited N 2 molecules and N atoms.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Topography, surface water distribution and subsurface structure in 2023 across an Arctic coastal tundra site near Utqiagvik, Alaska

Subsurface electrical resistivity tomography (ERT), active layer thickness measurements, photogrammetry, and topographic data were collected in September 2023 along a 475 m long, 20 m wide corridor that traverses various polygon types within the Barrow Environmental Observatory (BEO) on the Alaskan Arctic Coastal Plain, approximately 4 miles from the Beaufort Sea near Utqiaġvik, Alaska. These measurements were designed to assess decadal changes in surface water distribution, topography, and subsurface structure across this dynamic landscape. This archive contains the datasets acquired in 2023 and references to the datasets acquired previously at the same location. The ERT survey was conducted along the 475 m transect using 0.5 m electrode spacing and a roll-along acquisition strategy. Thaw layer thicknesses were measured with a tile probe along the same transect. Photogrammetry data were acquired using an unoccupied aerial vehicle (UAV) and were used to generate a digital elevation model and an RGB mosaic. A real-time kinematic (RTK) GPS was used to survey the ERT electrodes and the ground control points for the aerial imagery. The dataset contains 5 *.csv data files, 6 *.csv metadata files, and 6 *.tif files.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1983

Effect of tail-fin span on stability and control characteristics of a Canard-controlled missile at supersonic Mach numbers

An experimental wind-tunnel investigation was conducted at Mach numbers from 1.60 to 3.50 to obtain the longitudinal and lateral-directional aerodynamic characteristics of a circular, cruciform, canard-controlled missile with variations in tail-fin span. In addition, comparisons were made with the experimental aerodynamic characteristics using three missile aeroprediction programs: MISSILE1, MISSILE2, and NSWCDM. The results of the investigation indicate that for the test Mach number range, canard roll control at low angles of attack is feasible on tail-fin configurations with tail-to-canard span ratios of less than or equal to 0.75. The conards are effective pitch and yaw control devices on each tail-fin span configuration tested. Programs MISSILE1 and MISSILE2 provide very good predictions of longitudinal aerodynamic characteristics and fair predictions of lateral-directional aerodynamic characteristics at low angles of attack, with MISSILE2 predictions generally in better agreement with test data. Program NSWCDM provides good longitudinal and lateral-directional aerodynamic predictions that improve with increases in tail-tin span.

Blair, A. B., Jr.↗
NASA NTRS1983

Space Shuttle third flight /STS-3/ entry RCS analysis

Flight data obtained from three Space Transportation System orbiter entries (STS-1, 2, and 3) are processed and analyzed to determine the roll interactions caused by the firing of the entry reaction control system (RCS). Comparisons between the flight-derived parameters and the predicted derivatives without interaction effects are made. The flight-derived RCS Plume flow-field interaction effects are independently deduced by direct integration of the incremental changes in the wing upper surface pressures induced by RCS side thruster firings. The separately obtained interaction effects are compared to the predicted values and the differences are discussed.

Scallion, W. I.↗
NASA NTRS1993

A musculoskeletal model of the elbow joint complex

This paper describes a musculoskeletal model that represents human elbow flexion-extension and forearm pronation-supination. Musculotendon parameters and the skeletal geometry were determined for the musculoskeletal model in the analysis of ballistic elbow joint complex movements. The key objective was to develop a computational model, guided by optimal control, to investigate the relationship among patterns of muscle excitation, individual muscle forces, and movement kinematics. The model was verified using experimental kinematic, torque, and electromyographic data from volunteer subjects performing both isometric and ballistic elbow joint complex movements. In general, the model predicted kinematic and muscle excitation patterns similar to what was experimentally measured.

Gonzalez, Roger V.↗
NASA NTRS1999

Smagglce: Surface Modeling and Grid Generation for Iced Airfoils: Phase 1 Results

SmaggIce (Surface Modeling and Grid Generation for Iced Airfoils) is a software toolkit used in the process of aerodynamic performance prediction of iced airfoils with grid-based Computational Fluid Dynamics (CFD). It includes tools for data probing, boundary smoothing, domain decomposition, and structured grid generation and refinement. SmaggIce provides the underlying computations to perform these functions, a GUI (Graphical User Interface) to control and interact with those functions, and graphical displays of results, it is being developed at NASA Glenn Research Center. This paper discusses the overall design of SmaggIce as well as what has been implemented in Phase 1. Phase 1 results provide two types of software tools: interactive ice shape probing and interactive ice shape control. The ice shape probing tools will provide aircraft icing engineers and scientists with an interactive means to measure the physical characteristics of ice shapes. On the other hand, the ice shape control features of SmaggIce will allow engineers to examine input geometry data, correct or modify any deficiencies in the geometry, and perform controlled systematic smoothing to a level that will make the CFD process manageable.

Vickerman, Mary B.↗
NASA NTRS2001

NASA IVHM Technology Experiment for X-vehicles (NITEX)

The purpose of the NASA IVHM Technology Experiment for X-vehicles (NITEX) is to advance the development of selected IVHM technologies in a flight environment and to demonstrate the potential for reusable launch vehicle ground processing savings. The technologies to be developed and demonstrated include system-level and detailed diagnostics for real-time fault detection and isolation, prognostics for fault prediction, automated maintenance planning based on diagnostic and prognostic results, and a microelectronics hardware platform. Complete flight The Evolution of Flexible Insulation as IVHM consists of advanced sensors, distributed data acquisition, data processing that includes model-based diagnostics, prognostics and vehicle autonomy for control or suggested action, and advanced data storage. Complete ground IVHM consists of evolved control room architectures, advanced applications including automated maintenance planning and automated ground support equipment. This experiment will advance the development of a subset of complete IVHM.

Sandra, Hayden↗
NASA NTRS2005

Experimental Results for an Annular Aerospike with Differential Throttling

A) MSFC funded an internal study on Altitude Compensating Nozzles: 1) Develop an ACN design and performance prediction tool. 2) Design, build and test cold flow ACN nozzles. 3) An annular aerospike nozzle was designed and tested. 4) Incorporated differential throttling to assess Thrust Vector Control. B) Objective of the test hardware: 1) Provide design tool verification. 2) Provide benchmark data for CFD calculations. 3) Experimentally measure side force, or TVC, for a differentially throttled annular aerospike.

Ruf, Joseph H.↗
NASA NTRS2010

Lifetime Assessment of the NEXT Ion Thruster

Ion thrusters are low thrust, high specific impulse devices with required operational lifetimes on the order of 10,000 to 100,000 hr. The NEXT ion thruster is the latest generation of ion thrusters under development. The NEXT ion thruster currently has a qualification level propellant throughput requirement of 450 kg of xenon, which corresponds to roughly 22,000 hr of operation at the highest throttling point. Currently, a NEXT engineering model ion thruster with prototype model ion optics is undergoing a long duration test to determine wear characteristics and establish propellant throughput capability. The NEXT thruster includes many improvements over previous generations of ion thrusters, but two of its component improvements have a larger effect on thruster lifetime. These include the ion optics with tighter tolerances, a masked region and better gap control, and the discharge cathode keeper material change to graphite. Data from the NEXT 2000 hr wear test, the NEXT long duration test, and further analysis is used to determine the expected lifetime of the NEXT ion thruster. This paper will review the predictions for all of the anticipated failure mechanisms. The mechanisms will include wear of the ion optics and cathode s orifice plate and keeper from the plasma, depletion of low work function material in each cathode s insert, and spalling of material in the discharge chamber leading to arcing. Based on the analysis of the NEXT ion thruster, the first failure mode for operation above a specific impulse of 2000 sec is expected to be the structural failure of the ion optics at 750 kg of propellant throughput, 1.7 times the qualification requirement. An assessment based on mission analyses for operation below a specific impulse of 2000 sec indicates that the NEXT thruster is capable of double the propellant throughput required by these missions.

VanNoord, Jonathan L.↗
NASA NTRS2018

Buoyancy Effects on Concurrent Flame Spread Over Thick PMMA

The flammability of combustible materials in a spacecraft is important for fire safety applications because the conditions in spacecraft environments differ from those on earth. Experimental testing in space is difficult and expensive. However, reducing buoyancy by decreasing ambient pressure is a possible approach to simulate on-earth the burning behavior inside spacecraft environments. The objective of this work is to determine that possibility by studying the effect of pressure on concurrent flame spread, and by comparison with microgravity data, observe up to what point low-pressure can be used to replicate flame spread characteristics observed in microgravity. Specifically, this work studies the effect of pressure and microgravity on upward/concurrent flame spread over 10 mm thick polymethyl methacrylate (PMMA) slabs. Experiments in normal gravity were conducted over pressures ranging between 100 and 40 kPa and a forced flow velocity of 200 mm/s. Microgravity experiments were conducted during NASA’s Spacecraft Fire Experiment (Saffire II), on board the Cygnus spacecraft at 100 kPa with an air flow velocity of 200 mm/s. Results show that reductions of pressure slow down the flame spread over the PMMA surface approaching that in microgravity. The data is correlated in terms of a non-dimensional mixed convection analysis that describes the convective heat transferred from the flame to the solid, and the primary mechanism controlling the spread of the flame. The extrapolation of the correlation to low pressures predicts well the flame spread rate obtained in microgravity in the Saffire II experiments. Similar results were obtained by the authors with similar experiments with a thin composite cotton/fiberglass fabric (published elsewhere). Both results suggest that reduced pressure can be used to approximately replicate flame behavior of untested gravity conditions for the burning of thick and thin solids. This work could provide guidance for potential ground-based testing for fire safety design in spacecraft and space habitats.

Environmental conditions↗
NASA NTRSDate not supplied

TPSAS-NF1676L-15194-DND

Technical Motivation - 1950s: Indication of large lateral (roll/yaw) acceleration (“β-dot”) dynamic derivatives for configurations with strong vortex flows in the stall region (Lichtenstein, Campbell, Riley)! - 1960s: Increased emphasis on use of long-range missiles tempered by aircraft losses in close-in air combat - 1970s: - Effect of lateral acceleration derivatives on aircraft stability (Nguyen) - Characteristics and air combat advantages of rapid controlled large-amplitude maneuvering at low speeds near maximum lift shown in piloted simulations (Herbst) - 1980s: - Dynamic (forced-oscillation, rotary balance, curved- and rolling-flow) wind tunnel tests (Grafton, Lutze, Hultberg) - Incorporation of test data into computer simulations (Kalviste) - Technologies developed for controlled maneuvers at stall, post-stall angles of attack - Concern that conventional math modeling inadequately represented the dynamic component of these motions - Need to evaluate dependency of control laws on accurate computer simulations and motion prediction

Marilyn E Ogburn↗