Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cost analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Study of aircraft crashworthiness for fire protection

Impact-survivable postcrash fire accidents were surveyed. The data base developed includes foreign and domestic accidents involving airlines and jet aircraft. The emphasis was placed on domestic accidents, airlines, and jet aircraft due principally to availability of information. Only transport category aircraft in commercial service designed under FAR Part 25 were considered. A matrix was prepared to show the relationships between the accident characteristics and the fire fatalities. Typical postcrash fire scenaries were identified. Safety concepts were developed for three engineering categories: cabin interiors - cabin subsystems; power plant - engines and fuel systems; and structural mechanics - primary and secondary structures. The parameters identified for concept evaluation are cost, effectiveness, and societal concerns. Three concepts were selected for design definition and cost and effectiveness analysis: improved fire-resistant seat materials; anti-misting kerosene; and additional cabin emergency exits.

Cominsky, A.↗
NASA NTRS1980

Appendix E: Research papers. Analysis of landfills with historic airphotos

The nature of landfill-related information that can be derived from existing, or historic, aerial photographs, is reviewed. This information can be used for conducting temporal assessments of landfill existence, land use and land cover, and the physical environment. As such, analysis of low cost, readily available aerial photographs can provide important, objective input to landfill inventories, assessing contamination or health hazards, planning corrective measures, planning waste collection and facilities, and developing on inactive landfills.

Liang, T.↗
NASA NTRS1981

A Module Experimental Process System Development Unit (MEPSDU)

Design work for a photovoltaic module, fabricated using single crystal silicon dendritic web sheet material, resulted in the identification of surface treatment to the module glass superstrate which improved module efficiencies. A final solar module environmental test, a simulated hailstone impact test, was conducted on full size module superstrates to verify that the module's tempered glass superstrate can withstand specified hailstone impacts near the corners and edges of the module. Process sequence design work on the metallization process selective, liquid dopant investigation, dry processing, and antireflective/photoresist application technique tasks, and optimum thickness for Ti/Pd are discussed. A noncontact cleaning method for raw web cleaning was identified and antireflective and photoresist coatings for the dendritic webs were selected. The design of a cell string conveyor, an interconnect feed system, rolling ultrasonic spot bonding heat, and the identification of the optimal commercially available programmable control system are also discussed. An economic analysis to assess cost goals of the process sequence is also given.

Source record↗
NASA NTRS1983

The NASA Suborbital Program: A status review

The status of the NASA suborbital program is reviewed and its importance to astrophysical and geophysical programs is assessed. A survey of past scientific and developmental accomplishments, an examination of the trends in program costs, and an analysis of current and future program roles are included. The technical disciplines examined are primarily those of astronomy/astrophysics/solar physics and magnetospheric/ionospheric/ atmospheric physics.

Teeter, R.↗
NASA NTRS1984

Mathematical synthesization of complex structures

A mathematical synthesization approach for rapidly modeling and analyzing complex structures comprised of hundreds or thousands of repeating individual structural members, interconnecting hardware, and other components was described. The techniques are applicable to any structure with repeating structural members. The capabilities are embodied within the Interactive Design and Evaluation of Advanced Spacecraft (IDEAS) computer-aided design system. IDEAS has a full range of integrated spacecraft modeling, design, analysis, performance, and cost estimating capabilities which include about 40 technical program and executive, data base, and file management systems. With IDEAS, a single user at an interactive terminal can create, design, analyze, and conduct parametric studies of Earth orbiting spacecraft in a timely, cost-efficient manner. The system is particularly useful in the conceptual design phases of advanced space missions when a multiplicity of concepts must be evaluated. The IDEAS interactive finite-element modeling capabilities are discussed. The mathematical synthesization programs were structured not only to provide a detailed finite-element model of the structure but also to automatically perform the many auxiliary computations needed to analyze the spacecraft in its orbital operational environment.

Garrett, L. B.↗
NASA NTRS1984

Cost prediction model for various payloads and instruments for the Space Shuttle Orbiter

The following cost parameters of the space shuttle were undertaken: (1) to develop a cost prediction model for various payload classes of instruments and experiments for the Space Shuttle Orbiter; and (2) to show the implications of various payload classes on the cost of: reliability analysis, quality assurance, environmental design requirements, documentation, parts selection, and other reliability enhancing activities.

Hoffman, F. E.↗
NASA NTRS1987

A zonal method for modeling 3-D aircraft flow fields with jet plume effects

A coupled zonal method has been developed for modeling flows about aircraft with highly integrated advanced nozzle installations in which the exhaust plume interacts with the aircraft flow field to enhance performance. A cost effective flow analysis is achieved by dividing the flow domain into zones and coupling the zonal solutions. PAN AIR is used to model the flow in the inviscid zone which surrounds the aircraft. The plume zone flow field is solved with a PNS code. The flow in the optional internal nozzle zone is modeled using a full Navier-Stokes code. An automated iterative procedure couples the inviscid and plume zones by passing updated boundary conditions between the zones. The coupled analysis provides converged solutions for the overall flow field. The method is demonstrated for a highly integrated nonaxisymmetric vectored nozzle installed on a swept-wing aircraft.

Roberts, D. W.↗
NASA NTRS1989

A zonal method for modeling powered-lift aircraft flow fields

A zonal method for modeling powered-lift aircraft flow fields is based on the coupling of a three-dimensional Navier-Stokes code to a potential flow code. By minimizing the extent of the viscous Navier-Stokes zones the zonal method can be a cost effective flow analysis tool. The successful coupling of the zonal solutions provides the viscous/inviscid interations that are necessary to achieve convergent and unique overall solutions. The feasibility of coupling the two vastly different codes is demonstrated. The interzone boundaries were overlapped to facilitate the passing of boundary condition information between the codes. Routines were developed to extract the normal velocity boundary conditions for the potential flow zone from the viscous zone solution. Similarly, the velocity vector direction along with the total conditions were obtained from the potential flow solution to provide boundary conditions for the Navier-Stokes solution. Studies were conducted to determine the influence of the overlap of the interzone boundaries and the convergence of the zonal solutions on the convergence of the overall solution. The zonal method was applied to a jet impingement problem to model the suckdown effect that results from the entrainment of the inviscid zone flow by the viscous zone jet. The resultant potential flow solution created a lower pressure on the base of the vehicle which produces the suckdown load. The feasibility of the zonal method was demonstrated. By enhancing the Navier-Stokes code for powered-lift flow fields and optimizing the convergence of the coupled analysis a practical flow analysis tool will result.

Roberts, D. W.↗
NASA NTRS1990

Development of BEM for ceramic composites

Details on the progress made during the first three years of a five-year program towards the development of a boundary element code are presented. This code was designed for the micromechanical studies of advance ceramic composites. Additional effort was made in generalizing the implementation to allow the program to be applicable to real problems in the aerospace industry. The ceramic composite formulations developed were implemented in the three-dimensional boundary element computer code BEST3D. BEST3D was adopted as the base for the ceramic composite program, so that many of the enhanced features of this general purpose boundary element code could by utilized. Some of these facilities include sophisticated numerical integration, the capability of local definition of boundary conditions, and the use of quadratic shape functions for modeling geometry and field variables on the boundary. The multi-region implementation permits a body to be modeled in substructural parts; thus dramatically reducing the cost of the analysis. Furthermore, it allows a body consisting of regions of different ceramic matrices and inserts to be studied.

Henry, D. P.↗
NASA NTRS1992

Developing Software For A Flight-Control System

Improved process for development of flight-control software devised by integrating conventional software-development process with conventional control-system-analysis process. Reduces costs of development, eliminates need for reengineering, and almost eliminates production errors. Concept applicable to design of other control systems and of complicated hardware-and-software systems in general.

Murray, Jonathan↗
NASA NTRS1993

Reliability enhancement of Navier-Stokes codes through convergence enhancement

Reduction of total computing time required by an iterative algorithm for solving Navier-Stokes equations is an important aspect of making the existing and future analysis codes more cost effective. Several attempts have been made to accelerate the convergence of an explicit Runge-Kutta time-stepping algorithm. These acceleration methods are based on local time stepping, implicit residual smoothing, enthalpy damping, and multigrid techniques. Also, an extrapolation procedure based on the power method and the Minimal Residual Method (MRM) were applied to the Jameson's multigrid algorithm. The MRM uses same values of optimal weights for the corrections to every equation in a system and has not been shown to accelerate the scheme without multigriding. Our Distributed Minimal Residual (DMR) method based on our General Nonlinear Minimal Residual (GNLMR) method allows each component of the solution vector in a system of equations to have its own convergence speed. The DMR method was found capable of reducing the computation time by 10-75 percent depending on the test case and grid used. Recently, we have developed and tested a new method termed Sensitivity Based DMR or SBMR method that is easier to implement in different codes and is even more robust and computationally efficient than our DMR method.

Choi, K.-Y.↗
NASA NTRS1993

New proof of the Jacobi necessary condition

A new proof is given for Jacobi's necessary condition. It is shown that the existence of a conjugate point in the interior of an extremal implies the existence of control perturbations which lead to a reduction in cost. The present analysis is restricted to linear-quadratic optimal control problems.

Seywald, Hans↗
NASA NTRS1993

Lessons learned - MO&DA at JPL

The issues of how to avoid future surprise growth in Mission Operations and Data Analysis (MO&DA) costs and how to minimize total MO&DA costs for planetary missions are discussed within the context of JPL mission operations support. It is argued that there is no simple, single solution: the entire Project life-cycle must be addressed. It is concluded that cost models that can predict both MO&DA cost as well as Ground System development costs are needed. The first year MO&DA budget plotted against the total of ground and flight systems developments is shown. In order to better recognize changes and control costs in general, a modified funding line item breakdown is recommended to distinguish between development costs (prelaunch and postlaunch) and MO&DA costs.

Handley, Thomas H., Jr.↗
NASA NTRS1994

On the application of under-decimated filter banks

Maximally decimated filter banks have been extensively studied in the past. A filter bank is said to be under-decimated if the number of channels is more than the decimation ratio in the subbands. A maximally decimated filter bank is well known for its application in subband coding. Another application of maximally decimated filter banks is in block filtering. Convolution through block filtering has the advantages that parallelism is increased and data are processed at a lower rate. However, the computational complexity is comparable to that of direct convolution. More recently, another type of filter bank convolver has been developed. In this scheme, the convolution is performed in the subbands. Quantization and bit allocation of subband signals are based on signal variance, as in subband coding. Consequently, for a fixed rate, the result of convolution is more accurate than is direct convolution. This type of filter bank convolver also enjoys the advantages of block filtering, parallelism, and a lower working rate. Nevertheless, like block filtering, there is no computational saving. In this article, under-decimated systems are introduced to solve the problem. The new system is decimated only by half the number of channels. Two types of filter banks can be used in the under-decimated system: the discrete Fourier transform (DFT) filter banks and the cosine modulated filter banks. They are well known for their low complexity. In both cases, the system is approximately alias free, and the overall response is equivalent to a tunable multilevel filter. Properties of the DFT filter banks and the cosine modulated filter banks can be exploited to simultaneously achieve parallelism, computational saving, and a lower working rate. Furthermore, for both systems, the implementation cost of the analysis or synthesis bank is comparable to that of one prototype filter plus some low-complexity modulation matrices. The individual analysis and synthesis filters have complex coefficients in the DFT filter banks but have real coefficients in the cosine modulated filter banks.

Lin, Y.-P.↗
NASA NTRS2004

Lunar and Planetary Science XXXV: Human Occupation of Space: Radiation, Risk, and Refuse

The titles in this section include: 1) Discrimination of Heavy Charged Particles in a Mixed Irradiation Using Optically Stimulated Luminescence Methods 2) MARIE: Current Status and Results from 20 Months of Observations at Mars 3) Mars Surface Analog Project: Preparing for Astronauts First Hours on Mars 4) The Need for Analogue Missions in Scientific Human and Robotic Planetary Exploration 5) Space Debris in the Geosynchronous Earth Orbit: Debris Environmental Asssessment and its Implications on Cost and Benefit Analysis.

Source record↗
NASA NTRS2005

Manufacture of Solar Cells on the Moon

In support of the space exploration initiative a new architecture for the production of solar cells on the lunar surface is devised. The paper discusses experimental data on the fabrication and properties of lunar glass substrates, evaporated lunar regolith thin film (antireflect coatings and insulators), and preliminary attempts in the fabrication of thin film (silicon/II-VI) photovoltaic materials on lunar regolith substrates. A conceptual design for a solar powered robotic rover capable of fabricating solar cells directly on the lunar surface is provided. Technical challenges in the development of such a facility and strategies to alleviate perceived difficulties are discussed. Finally, preliminary cost benefit ratio analysis for different in situ solar cell production scenarios (using exclusively in-situ planetary resources or hybrid) are discussed.

Freundich, Alex↗
NASA NTRS1998

Statistical Treatment of Earth Observing System Pyroshock Separation Test Data

The Earth Observing System (EOS) AM-1 spacecraft for NASA's Mission to Planet Earth is scheduled to be launched on an Atlas IIAS vehicle in June of 1998. One concern is that the instruments on the EOS spacecraft are sensitive to the shock-induced vibration produced when the spacecraft separates from the launch vehicle. By employing unique statistical analysis to the available ground test shock data, the NASA Lewis Research Center found that shock-induced vibrations would not be as great as the previously specified levels of Lockheed Martin. The EOS pyroshock separation testing, which was completed in 1997, produced a large quantity of accelerometer data to characterize the shock response levels at the launch vehicle/spacecraft interface. Thirteen pyroshock separation firings of the EOS and payload adapter configuration yielded 78 total measurements at the interface. The multiple firings were necessary to qualify the newly developed Lockheed Martin six-hardpoint separation system. Because of the unusually large amount of data acquired, Lewis developed a statistical methodology to predict the maximum expected shock levels at the interface between the EOS spacecraft and the launch vehicle. Then, this methodology, which is based on six shear plate accelerometer measurements per test firing at the spacecraft/launch vehicle interface, was used to determine the shock endurance specification for EOS. Each pyroshock separation test of the EOS spacecraft simulator produced its own set of interface accelerometer data. Probability distributions, histograms, the median, and higher order moments (skew and kurtosis) were analyzed. The data were found to be lognormally distributed, which is consistent with NASA pyroshock standards. Each set of lognormally transformed test data produced was analyzed to determine if the data should be combined statistically. Statistical testing of the data's standard deviations and means (F and t testing, respectively) determined if data sets were significantly different at a 95-percent confidence level. If two data sets were found to be significantly different, these families of data were not combined for statistical purposes. This methodology produced three separate statistical data families of shear plate data. For each population, a P99.1/50 (probability/confidence) per-separation-nut firing level was calculated. By using the binomial distribution, Lewis researchers determined that this pernut firing level was equivalent to a P95/50 per-flight confidence level. The overall envelope of the per-flight P95/50 levels led to Lewis' recommended EOS interface shock endurance specification. A similar methodology was used to develop Lewis' recommended EOS mission assurance levels. The available test data for the EOS mission are significantly larger than for a normal mission, thus increasing the confidence level in the calculated expected shock environment. Lewis significantly affected the EOS mission by properly employing statistical analysis to the data. This analysis prevented a costly requalification of the spacecraft's instruments, which otherwise would have been exposed to significantly higher test levels.

McNelis, Anne M.↗
NASA NTRS2006

Assisting Public Organizations in Their Outsourcing Endeavors: A Decision Support Mode

There has been a tremendous growth in outsourcing practices in recent years. The public organizations in the United States have outsourced some functions and are now being compelled to outsource additional ones. While there are numerous studies that document and analyze outsourcing practices, there is limited research to guide public or governmental organizations in determining what functions to outsource. This study fills this gap by developing a decision support model for a typical public organization in determining what to outsource and how. A set of outsourcing decision factors is identified that can be used as parameters in the three integer programming formulations developed. These formulations are used as solution engines in the model. The first formulation identifies which functions are the best candidates for outsourcing given the organization's priorities. The other formulations place the functions into recommended contracts and re-assign displaced employees. Data from NASA Glenn Research Center in Ohio is used to test and analyze the model. Analysis indicates that cost and skills-related factors are the most sensitive parameters for the data tested. The model and the formulations are a relatively comprehensive package and may help guide outsourcing decisionmakers and policymakers in public organizations.

Kremic, TIbor↗