Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “circuit optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Ground Fault Overvoltage With Inverter-Interfaced Distributed Energy Resources

Ground Fault Overvoltage can occur in situations in which a four-wire distribution circuit is energized by an ungrounded voltage source during a single phase to ground fault. The phenomenon is well-documented with ungrounded synchronous machines, but there is considerable discussion about whether inverters cause this phenomenon, and consequently whether inverters require effective grounding. This paper examines the overvoltages that can be supported by inverters during single phase to ground faults via theory, simulation and experiment, identifies the relevant physical mechanisms, quantifies expected levels of overvoltage, and makes recommendations for optimal mitigation.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Advanced Components for Spaceborne Infrared Astronomy

Basic improvements in the technology of low noise read-out systems for low background detectors were demonstrated. Using discrete JFET integrating amplifiers at their optimum temperature of 55 K, read noise less than 7.5 electrons in 128 seconds of integration was obtained. Two models of single channel integrators are now available, the JF-77 for use between 50 and 80 K and the JF-4 for lower temperatures. A 1 x 15 linear array of complete integrators on a single integrated circuit was developed and will be made available in the near future. The successful operation of a superconducting stepper motor was demonstrated. The motor shows a three fold increase in torque over conventional motors operating at room temperature. The success of the motor stems from the use of superconducting coils in conjunction with developments in bearings for cryogenic use, rare-earth rotors, and motor cooling techniques. The current state of development will allow the rapid development of motors optimized for specific applications. An electronic switch capable of resetting cooled JFET integrating amplifiers was developed. The JFET integrating amplifiers that use this switch have demonstrated read noise of less than 10 electrons. The JFET reset device exhibits an extremely high open impedance and low leakage current. Capacitance is sufficiently low so as not to impair amplifier sensitivity. The effects of transient switching charges are minimized by a compensation technique and variable transient current problems inherent to devices of this type are overcome by external circuity.

Davidson, Arnold W.↗

Advancing Reel-to-Reel Inspection Techniques for Long HTS Conductors: Comparison and Innovations

The continuous advancement of high-temperature superconductor (HTS) technologies has greatly accelerated the development and deployment of HTS applications. Among the critical tools supporting these advancements are reel-to-reel (R2R) critical current (I c ) measurement techniques, which are extensively used by both manufacturers and end users to characterize long-length REBCO conductors. These techniques play a vital role in quality assurance and quality control (QA/QC), ensuring the reliability and performance of HTS conductors and applications throughout the production cycle. We have developed a range of in-house devices for R2R measurements at the University of Houston and Princeton Plasma Physics Laboratory. These include one-dimensional (1D) scan using a magnetic circuit (MC) and two-dimensional (2D) magnetic field mapping systems based on scanning probe array microscope (SPAM) or scanning probe microscopy (SPM). Each technique offers distinct advantages: the MC system provides ultra-fast scanning speeds, ideal for rapid inspection in large-scale industrial production; the high-resolution SPM delivers detailed insights for conductor research and development; and the SPAM, with its simpler mechanical setup, can be upgraded for higher field and lower temperature conditions with a balanced 2D resolution. Here we compared the magnetization and detection capabilities of these techniques through experiments on rare-earth barium copper oxide (REBCO) coated conductor samples, with data analysis supported by numerical simulations. Based on our comprehensive comparative studies, we propose enhancements for each measurement system and provide guidelines for selecting the optimal technique combinations to meet specific application requirements.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

>24% screen printed Cu contacted n-TOPCon solar cells with successful implementation of LECO process

In this paper, we report the successful fabrication of >24.0 % efficiency n-TOPCon Si solar cells with screen-printed, fire-through Cu contact to n-TOPCon on the rear side and Ag contacted boron emitter on the front side by implementing optimized firing and LECO conditions. The highest efficiency (24.3%) Cu contacted n-TOPCon cell in this study showed excellent cell performance parameters with V oc >730 mV, J sc of 41.1 mA/cm 2 and FF of 80.8%, resulting in an absolute efficiency gap of 0.2% between Cu-contacted and fully Ag contacted n-TOPCon cells (24.5%). The mini-module fabricated with the Cu contacted n-TOPCon cell showed excellent reliability and durability of open-circuit voltage (V oc ), pseudo fill factor (pFF) and efficiency after prolonged damp-heat tests. Such high efficiency screen printed Cu contacted n-TOPCon cells provide unique opportunity to replace very expensive Ag contact on n-TOPCon with cheaper screen printable Cu metal pastes.

14 SOLAR ENERGY↗

Effect of nanoscale tin-dioxide layers on the efficiency of CdS/CdTe-based film solar elements

Comparative investigations of the output parameters and optical diode characteristics of ITO/CdS/CdTe/Cu/Au and SnO{sub 2}: F/CdS/CdTe/Cu/Au film solar cells are carried out with the aim of optimizing the design of the front electrodes. It is established that the high voltage and large filling factor of the solar elements with SnO{sub 2}: F films are caused by a lower diode saturation current density and series resistance due to the stability of the crystal structure and electrical properties of these films against chloride treatment of the base layer during device fabrication. At the same time, solar elements with an ITO front electrode exhibit a higher short-circuit current density due to the larger average light transmittance of the ITO layers. The use of nanoscale SnO{sub 2} layers in the ITO front contacts allows the efficiency of the CdS/CdTe-based solar elements to be enhanced to 11.4% on account of stabilization of the crystal structure and electrical properties of the ITO films and a possible reduction in the cadmium-sulphide-layer thickness without shunting the device structure.

36 MATERIALS SCIENCE↗

Surface Passivation and Carrier Collection in {110}, {100} and Circular Si Microwire Solar Cells

Surface recombination is a major bottleneck for realizing highly efficient micro/nanostructure solar cells. Parametric studies of the influence of Si microwire (SiMW) surface-facet orientation (rectangular with flat-facets, {110}, {100} and circular), with a fixed height of 10 µm, diameter (D = 1.5–9.5 µm), and sidewall spacing (S = 2.5–8.5 µm), and mesh-grid density (1–16 mm -2 ) on recombination and carrier collection in SiMW solar cells with radial p-n junctions are reported. An effective surface passivation layer composed of thin thermally grown silicon dioxide (SiO 2 ) and silicon nitride (SiN x ) layers is employed. For a fixed D of 1.5 µm, tight SiMW spacing results in improved short-circuit current density (J sc = 30.1 mA cm -2 ) and sparse arrays result in open-circuit voltages (V oc = 0.552 V) that are similar to those of control Si planar cells. For a fixed S, smaller D results in better light trapping at shorter wavelengths and higher J sc while larger D exhibits better light trapping at larger wavelengths and a higher V oc . With a mesh-grid electrode the power conversion efficiency increases to 15.3%. Finally, these results provide insights on the recombination mechanisms in SiMW solar cells and provide general design principles for optimizing their performance.

14 SOLAR ENERGY↗

A chlorinated polymer promoted analogue co-donors for efficient ternary all-polymer solar cells

The efficient ternary all-polymer solar cells (PSCs) are designed and fabricated, using a polymer acceptor of NDP-V-C 7 and analogue co-donors containing a chlorinated polymer PBClT and classical PTB 7 -Th. PBClT and PTB 7 -Th possess very similar chemical structure and matched energy levels to form the cascade of the co-donors. Meanwhile, benefiting from those analogous polymer structures, there is little influence of the morphology in blend film compared to their pristine polymer films. The binary PBClT:NDP-V-C 7 devices exhibit a high open-circuit voltage (Voc) due to the deep HOMO level of PBClT. The V oc of all-PSCs could be finely manipulated by adjusting the content of PBClT in blend film. The ternary all-PSCs have the more balanced charge mobility and prolonged carrier lifetime compared to the binary devices. The PBClT also help improve the miscibility of ternary blend and suppress crystallization in films, bringing about favorable morphology with appropriate orientation and surface roughness in blend film. With the optimal processing, the champion ternary all-PSCs obtain a high PCE of 9.03%, which is about 10% enhancement compared to that of binary device. Finally, the results indicate that the ternary approach using analogue co-donors is a practical method to enhance the performance of all-PSCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

InGaAsSb/GaSb thermophotovoltaic cells

AstroPower is developing InGaAsSb thermophotovoltaic (TPV) devices. This photovoltaic cell is a two-layer epitaxial InGaAsSb structure formed by liquid-phase epitaxy on a GaSb substrate. The (direct) bandgap of the In(1 - x)Ga(x)As(1 -y)Sb(y) alloy is 0.50 to 0.55 eV, depending on its exact alloy composition (x, y); and is closely lattice-matched to the GaSb substrate The use of the quaternary alloy, as opposed to a ternary alloy - such as, for example, InGaAs/InP - permits low bandgap devices optimized for 1000 to 1500 C thermal sources with, with at the time, near-exact lattice matching to the GaSb substrate. Lattice-matching is important since even a small degree of lattice mismatch degrades device performance and reliability and increases processing complexity. For bandgaps of 0.52 eV,Fo internal quantum efficiencies as high as 95% have been measured at a wavelength of 2 microns. At 1 micron wavelengths, internal quantum efficiencies of 55% have been observed. The open-circuit voltage at currents of 0.3 A/sq cm is 0.220 volts and 0.260 V for current densities of 2 A/sq cm. Fill factors of 56% have also been measured. These preliminary results lead to the conclusion that the GaSb-based quaternary compounds provide a viable and high performance energy conversion solution for thermophotovoltaic systems operating with 1000 to 1500 C source temperatures.

Mauk, M. G.↗

First-Principles Design and Analysis of an Efficient, Pb-Free Ferroelectric Photovoltaic Absorber Derived from ZnSnO 3

Ferroelectric oxides, which exhibit a spontaneous and reversible electric polarization, have recently gained interest for photovoltaic applications, because this polarization can potentially facilitate exciton separation and carrier extraction while also generating open-circuit voltages orders-of-magnitude larger than the band gap. However, photovoltaic efficiencies in these materials are often limited by large band gaps and high hole effective masses. Developing a means to simultaneously reduce both without destroying the ferroelectric polarization could revolutionize photovoltaic technologies. In this work, we use first-principles computations to describe how chemical substitution of oxygen in the recently characterized ferroelectric ZnSnO 3 with sulfur to form ZnSnS 3 reduces the band gap to a near-optimal 1.3 eV while leaving the polarization virtually unchanged. Furthermore, we show that other key photovoltaic materials characteristics, such as hole effective mass, dielectric constant, and absorption coefficient, are also dramatically improved by sulfur substitution. Finally, we demonstrate that the well-known semiconductor GaN provides an excellent substrate on which to grow ZnSnS 3 , forming a strongly bound interface that is free of intrinsic midgap states and exhibits an ideal band alignment for efficient carrier extraction. Finally, this work advances the search for an Earth-abundant, nontoxic, ferroelectric material exhibiting strong solar absorption, and may enable the development of solar cells with both high photovoltage and photocurrent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Printed Circuit Board Based Rotating Coils for Measuring Sextupole Magnets

Here, the use of Printed Circuit Boards (PCBs) for the inductive pick-up windings of rotating coil probes has made the construction of these precision magnetic measurement devices much more accessible. This paper discusses the design details for PCBs which on each layer of the board provide for simultaneous analog bucking (suppression) of dipole, quadrupole, and sextupole field components so as to more accurately measure the higher order harmonic fields in sextupole magnets. Techniques to generate designs are discussed, as well as trade-offs to optimize sensitivity. Examples of recent sextupole PCBs and their performance are given.

43 PARTICLE ACCELERATORS↗

Thin air-plasma-treated alkali fluoride layers for improved hole extraction in copper phthalocyanine/C70-based solar cells

Alkali fluorides, mostly LiF and CsF, are well-known to improve electron injection/extraction in organic light-emitting diodes (OLEDs) and organic solar cells (OSCs). They are also utilized, though to a lesser extent, for hole injection in OLEDs. Here we demonstrate a new role for such fluorides in enhancing OSCs’ hole extraction.We show that an ultrathin air-plasmatreated alkali fluoride layer between the indium tin oxide (ITO) anode and the active layer in copper phthalocyanine (CuPc)/C 70 -based OSCs increases the short circuit current by up to ~17% for cells with LiF and ~7% for cells with NaF or CsF. The effects of the fluoride layer thickness and treatment duration were evaluated, as were OSCs with oxidized and plasma-treated Li and UV-ozone treated LiF. Measurements included current voltage, absorption, external quantum efficiency (EQE), atomic force microscopy, and x-ray photoelectron spectroscopy, which showed the presence of alkali atoms F and O at the treated ITO/fluoride surface. The EQE of optimized devices with LiF increased at wavelengths >560 nm, exceeding the absorption increase. Overall, the results indicate that the improved performance is due largely to enhanced hole extraction, possibly related to improved energy-level alignment at the fluorinated ITO/CuPc interface, reduced OSC series resistance, and in the case of LiF, improved absorption.

36 MATERIALS SCIENCE↗

Reduction of Methane Leaks through Corrosion Mitigation Pre-treatments for Pipelines with Field Applied Coatings

Corrosion of buried, coated steel pipelines transporting natural gas is a significant source of methane emissions, from pipeline venting required for maintenance and repairs and from pipeline leaks and incidents. Corrosion of steel under field applied coatings is an important safety concern for the pipeline industry. This project investigates the application of a field applied alloy over girth welds to mitigate external corrosion of buried coated steel pipelines. Various metallic coating options were considered, which were required to meet several criteria: (1) it must resist corrosion under open-circuit or mild cathodic protection conditions, (2) it must protect the substrate steel, and (3) it must not negatively affect the adhesion of the field coating. Finite element models and lab testing were performed of alloy coating compositions to identify promising alloy types underneath disbonded coatings. Polarization curves of coating alloys were generated to provide the boundary conditions for the COMSOL model to compute potential and current distributions around coated areas. Sacrificial and corrosion-resistant metal alloy coatings were evaluated and optimized using corrosion modeling and laboratory electrochemical testing, where aluminum alloy 5356 (5% Mg) and steel alloy B9 (9% Cr) were selected. Corrosion test coupons were designed and fabricated using thermal spray aluminum 5356 and welded B9 steel overlays on API 5L grade X42 line pipe steel. The corrosion test coupons, with simulated pipe coating damage, were tested in a laboratory soil box and a field pipeline site in Texas for 3-months. Corrosion test coupons were then tested for 6-months at field pipeline sites in Texas and Tennessee to quantify corrosion rates and performance of the aluminum and steel alloys under polyethylene tape and 2-part epoxy coatings, various coating holidays, and with and without cathodic protection.

03 NATURAL GAS↗

Pulsed Plasma Accelerator Modeling

This report presents the main results of the modeling task of the PPA project. The objective of this task is to make major progress towards developing a new computational tool with new capabilities for simulating cylindrically symmetric 2.5 dimensional (2.5 D) PPA's. This tool may be used for designing, optimizing, and understanding the operation of PPA s and other pulsed power devices. The foundation for this task is the 2-D, cylindrically symmetric, magnetohydrodynamic (MHD) code PCAPPS (Princeton Code for Advanced Plasma Propulsion Simulation). PCAPPS was originally developed by Sankaran (2001, 2005) to model Lithium Lorentz Force Accelerators (LLFA's), which are electrode based devices, and are typically operated in continuous magnetic field to the model, and implementing a first principles, self-consistent algorithm to couple the plasma and power circuit that drives the plasma dynamics.

Goodman, M.↗

Gigahertz-frequency acousto-optic phase modulation of visible light in a CMOS-fabricated photonic circuit

Optical phase modulators operating at visible wavelengths are essential components for photonic technologies such as those for quantum control, communications, and laser ranging. However, they remain challenging to implement in scalable, integrated platforms capable of handling high optical powers. Here we present a visible-light, gigahertz-frequency acousto-optic phase modulator, fabricated on a 200-mm wafer in a volume CMOS foundry, that supports greater than 500 mW of optical power at 730 nm. The device combines a piezoelectric transducer and a photonic waveguide within a single, wavelength-scale structure that confines both a propagating optical mode and an electrically excitable breathing-mode mechanical resonance. By tuning the device’s geometry to optimize the optomechanical interaction, we achieve modulation depths up to 4.85 rad with 80 mW of applied microwave power at 2.31 GHz in a 2-mm-long device. This corresponds to resonant modulation figures of merit of V π = 1.32V and V π ⋅ L = 0.26V cm. To our knowledge, this is the lowest V π ever demonstrated in any acousto-optic phase modulator and represents a 15-fold reduction in V π and a 100-fold reduction in required microwave power relative to state-of-the-art modulators with high visible-wavelength power handling commonly employed in quantum control systems.

Freedman, Jacob M. [Univ. of Arizona, Tucson, AZ (↗

Leaching of Au, Ag, and Pd from waste printed circuit boards of mobile phone by iodide lixiviant after supercritical water pre-treatment

Highlights: • We report a novel process for recovering Au, Ag, and Pd from waste PCBs. • The effect of SCWO on the leaching of Au, Ag, and Pd in waste PCBs was studied. • SCWO was highly efficient for enhancing the leaching of Au, Ag, and Pd. • The optimum leaching parameters for Au, Ag, and Pd in iodine–iodide were studied. - Abstract: Precious metals are the most attractive resources in waste printed circuit boards (PCBs) of mobile phones. In this work, an alternative process for recovering Au, Ag, and Pd from waste PCBs of mobile phones by supercritical water oxidation (SCWO) pre-treatment combined with iodine–iodide leaching process was developed. In the process, the waste PCBs of mobile phones were pre-treated in supercritical water, then a diluted hydrochloric acid leaching (HL) process was used to recovery the Cu, whose leaching efficiency was approximately 100%, finally the resulting residue was subjected to the iodine–iodide leaching process for recovering the Au, Ag, and Pd. Experimental results indicated that SCWO pre-treatment temperature, time, and pressure had significant influence on the Au, Ag, and Pd leaching from (SCWO + HL)-treated waste PCBs. The optimal SCWO pre-treatment conditions were 420 °C and 60 min for Au and Pd, and 410 °C and 30 min for Ag. The optimum dissolution parameters for Au, Pd, and Ag in (SCWO + HL)-treated PCBs with iodine–iodide system were leaching time of 120 min (90 min for Ag), iodine/iodide mole ratio of 1:5 (1:6 for Ag), solid-to-liquid ratio (S/L) of 1:10 g/mL (1:8 g/mL for Ag), and pH of 9, respectively. It is believed that the process developed in this study is environment friendly for the recovery of Au, Ag, and Pd from waste PCBs of mobile phones by SCWO pre-treatment combined with iodine–iodide leaching process.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Junction Quality of SnO 2 -Based Perovskite Solar Cells Investigated by Nanometer-Scale Electrical Potential Profiling

Electron-selective layers (ESLs) and hole-selective layers (HSLs) are critical in high-efficiency organic-inorganic lead halide perovskite (PS) solar cells for charge-carrier transport, separation, and collection. We developed a procedure to assess the quality of the ESL/PS junction by measuring potential distribution on cross-section of SnO 2 -based perovskite solar cells using Kelvin probe force microscopy. Using the potential profiling, we compared three types of cells made of different ESLs but otherwise having identical device structure: cells with PS deposited directly on bare fluorine-doped SnO 2 (FTO)-coated glass; cells with an intrinsic SnO 2 thin layer on the top of FTO as an effective ESL; and cells with the SnO2 ESL and adding a self-assembled monolayer (SAM) of fullerene. The results reveal two major potential drops or electric fields at the ESL/PS and PS/HSL interfaces. The electric-field ratio between the ESL/PS and PS/HSL interfaces increased in devices as follows: FTO < SnO 2 -ESL < SnO 2 +SAM; this sequence explains the improvements of fill factor (FF) and open-circuit voltage ( V oc ). The improvement of FF from the FTO to SnO 2 -ESL cells may result from the reduction in voltage lose at the PS/HSL back interface and the improvement of V oc from the prevention of hole recombination at the ESL/PS front interface. The further improvements with adding a SAM is caused by the defect passivation at the ESL/PS interface, and hence, improvement of the junction quality. Furthermore, these nanoelectrical findings suggest possibilities for improving the device performance by further optimizing the SnO2-based ESL material quality and the ESL/PS interface.

36 MATERIALS SCIENCE↗

Low-Loss, High-Flux Saturation Magnetic Cores for Power Converters

As new and alternative energy sources are added to the energy grid, efficient and low-loss power converters are essential to the storage of energy from these intermittent power sources. Higher operating frequency can reduce the size and weight of transformers. However, current magnetic cores limit the operating frequency because core losses increase with frequency. Therefore, new magnetic core materials are needed with higher resistivity (lower eddy-current losses), lower coercivity (lower hysteresis losses), and higher permeability and flux density (higher power density). These new materials must be integrated into isolated power converters designed to optimize efficiency based on the transformer performance. To address this need, Mainstream pursued a two-pronged approach in Phase I to develop novel magnetic materials and model a planar transformer design. We irradiated silicon steel with a high-energy electron beam in an attempt to induce nanocrystalline grain formation. The nanocrystalline grains were expected to increase resistivity to reduce eddy-current losses and decrease coercivity to reduce hysteresis losses. We also modeled the transformer performance through Simulation Program with Integrated Circuit Emphasis (SPICE) and analytical models to establish the effect of magnetic properties of the core on the performance of the transformer. There still are hurdles to be overcome in Phase II. The electron beam processing was successful in increasing the resistivity and the flux saturation density. However, the resistivity is still too low for high-frequency magnetic cores, because the eddy-current losses would be prohibitively high. Additionally, the coercivity increased for the processed samples leading to higher hysteresis losses. In comparing our SPICE and analytical models to the planar transformer measured values and impedance plots, good agreement was seen for primary and secondary short-circuit impedance measurements and for primary-to-secondary capacitance measurements. The SPICE model deviated from measured values, though, when measuring the transformer open-circuit impedance, indicating that we might need to add more model complexity to the transformer model. Phase II research will continue to build on the transformer model and integrating novel magnetic materials into high-frequency transformers.

15 GEOTHERMAL ENERGY↗

Development and Validation of a Simulation Tool to Predict the Combined Structural, Electrical, Electrochemical and Thermal Responses of Automotive Batteries

Battery safety is one of the most important design factors of electrified vehicles (EVs) since battery failure may lead to a catastrophic consequence. To improve the safety of battery systems in EVs, battery behaviors under various abuse conditions should be well understood. One way to examine battery response under extreme conditions is to conduct abuse tests in different scenarios. They can provide first-hand pass/fail information on battery safety, but they are usually expensive and time-consuming, which is inconvenient during design iterations and optimization. On the other hand, computational modeling can predict the battery behaviors in a more efficient and cost-effective way, which becomes an important tool to evaluate battery safety. Modeling battery responses and failure is challenging since it involves multiple coupled physical processes, needs to consider complex material properties and is computationally intensive. This project aims to develop a practical simulation tool to predict the combined structural, electrical, electrochemical, and thermal responses of automotive batteries to crash-induced crush and short circuit and validate it for conditions relevant to automotive crash. Advanced material constitutive models will be utilized to capture the mechanical response of cell components. Moreover, methods will be developed to reduce computational complexity of the model and allow battery safety simulations to extend from cell-level to module/pack level with affordable computational resources.

25 ENERGY STORAGE↗