Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “binder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Experimental and theoretical investigations on the adherent behaviors of high viscosity liquid: The effect of surface topography

Wetting test and classical molecular dynamics (MD) simulations were employed to investigate the adherent behaviors of hydroxyl-terminated polybutadiene (HTPB), a typical high viscosity liquid widely used as a binder in rocket motor propellants, onto the copper (Cu) surfaces with different topographies. Experimental data show that the microstructures protruding above the substrate surfaces can be ‘sensed’ by the HTPB droplet, which has been indicated by the smaller contact angles and higher interface tension for this specific liquid on the rough surfaces (featured with sinusoidal structures or square pillars) than that on the smooth surface. Simulation results reveal the atomic details of spreading process of HTPB chains, with diverse diffusion propensities presented on different surfaces. The HTPB droplet spreads widely on the smooth surface, exhibiting a roughly isotropic trend. On the contrary, the state of this high viscosity liquid on the sinusoidal-structured surface is featured by wide contact diffusion along the run of groove, but relatively restricted extension in the direction perpendicular to the groove, as a result of the barriers exerted by the nearest neighbouring peaks. The existence of nanoscale pillars increases the exterior surface area of Cu substrate, therefore the HTPB chains can penetrate deep to envelop the peripheries of the pillars, forming abundant direct contacts with Cu surface and producing a highest HTPB–Cu interaction energy, which well accords with the experimental results about the adherent strength of HTPB.

Wu, Chunya↗

Multi-scale boron penetration toward stabilizing nickel-rich cathode

Nickel-rich layered oxides LiNi x Co y Mn 1-x-y O 2 (x≥0.8) have been recognized as the preferred cathode materials to develop lithium-ion batteries with high energy density (>300Wh kg -1 ). However, the poor cycling stability and rate capability stemming from intergranular cracks and sluggish kinetics hinder their commercialization. To address such issues, a multi-scale boron penetration strategy is designed and applied on the polycrystalline LiNi 0.83 Co 0.11 Mn 0.06 O 2 particles that are pre-treated with pore construction. The lithium-ion conductive lithium borate in grain gaps functions as the grain binder that can bear the strain/stress from anisotropic contraction/expansion, and provides more pathways for lithium-ion diffusion. As a result, the intergranular cracks are ameliorated and the lithium-ion diffusion kinetics is improved. Moreover, the coating layer separates the sensitive cathode surface and electrolyte, helping to suppress the parasitic reactions and related gas evolution. In addition, the enhanced structural stability is acquired by strong B-O bonds with trace boron doping. As a result, the boron-modified sample with an optimized boron content of 0.5% (B5-NCM) exhibits a higher initial discharge capacity of 205.5mAh g -1 at 0.1C (1C=200mA g -1 ) and improved capacity retention of 81.7% after 100 cycles at 1C. Furthermore, the rate performance is distinctly enhanced by high lithium-ion conductive LBO (175.6mAh g -1 for B5-NCM and 154.6mAh g -1 for B0-NCM at 5C).

25 ENERGY STORAGE↗

Chickpea protein hydrolysate as a novel plant-based cryoprotectant in frozen surimi: Insights into protein structure integrity and gelling behaviors

Chickpea protein (CP) and its enzymatic hydrolysates are one of the most widely consumed pulse ingredients manifesting versatile applications in food industry, such as binders, emulsifiers, and meat protein substitutes. Other than those well-known functionalities, however, the use of CP as a cryoprotectant remained unexplored. Here, in this study, we prepared the chickpea protein hydrolysate (CPH) and investigated its cryoprotective effects to frozen surimi in terms of the protein structure integrity and gelling behaviors. Results indicated that CPH could inhibit myofibrillar protein (MP) denaturation and oxidation during the freeze–thaw cycling, as evidenced by their increased solubility, Ca 2+ -ATPase activity, sulfhydryl concentration, and declined content of disulfide bonds, carbonyl concentration and surface hydrophobicity. Freezing-induced changes on MP secondary structures were also retarded. Moreover, gels prepared from CPH-protected frozen surimi demonstrated more stabilized microstructure, uniform water distribution, enhanced elasticity, gel strength and water holding capacity. The CPH alone, at a reducing addition content of 4% (w/w), exhibited comparable cryoprotective performance to that of the commercial formulation (4% sucrose and 4% sorbitol). Therefore, this study provides scientific insights for development of pulse proteins as novel and high-performance food cryoprotectants.

59 BASIC BIOLOGICAL SCIENCES↗

Switching from batch to continuous granulation: A case study of metoprolol succinate ER tablets

Continuous manufacturing (CM) has been used to produce several immediate release drug products. No extended-release (ER) product manufactured employing CM technology has been approved yet. Herein this study investigated the critical aspects of switching from the batch mode of high shear granulation to the continuous operation of twin-screw granulation for extended-release tablets. Metoprolol succinate ER tablets was used as a model ER formulation for this purpose. A central composite design (CCD) was employed to determine the effects of high shear granulator (HSG) parameters, namely impeller speed, granulation time, and binder liquid feeding rate, on the critical granulation characteristics important for product performance. These critical granulation characteristics served as a guide for switching from the batch processing to the continuous operation for achieving the same breaking strength and dissolution for this ER metoprolol tablets. The granulation time was the most critical factor affecting the bulk properties of granules which contributed to tablet dissolution. The higher density and lower compressibility of granules were attained at the longest granulation time of 5.4 min with the fastest liquid feeding rate of 75 g/min. The granules’ density was the primary factor negatively affecting the dissolution of metoprolol tablets. However, the breaking strength of tablets confounded the effect of granules density on metoprolol dissolution. Switching the processing parameters of high shear granulation to twin-screw granulation achieved similar dissolution profiles (F2 greater than 50). The screw speed was not found to affect bulk properties of granules. The root cause of granulation failures in twin-screw granulation, such as premature consolidation, excessive swelling, poor cohesion, inconsistent shearing effects, and formation of deformed agglomerates, were identified. In conclusion, the use of critical granulation characteristics through a performance-based approach of ER tablets facilitated the switching of manufacturing of an ER formulation form batch to continuous operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multiscale electro-chemo-mechanical model of high-capacity amorphous silicon anode material in sodium-ion batteries

The growing interest in sodium-ion batteries (SIBs) is fueled by their abundant resources and environmentally friendly nature, with amorphous silicon (a-Si) emerging as a promising anode material for enhancing capacity. However, the key challenge lies in sustaining reversible capacity during cycling. Here, in this work, we developed a multiscale electrochemical model incorporating an a-Si anode to elucidate the performance parameters of SIBs. Additionally, we integrated an electro-chemo-mechanical model at the particle level to capture stress generation, an essential factor in the degradation of high-capacity electrodes. Unlike existing models, our approach accounts for large-deformation chemo-mechanics at the particle scale and includes simulations under varying charge rates to explore multiscale behavior. The results reveal that coupled sodiation significantly prolongs complete cycling times and influences discharge dynamics, indicating that neglecting this coupling leads to an underestimation of actual capacity. Furthermore, we observed pronounced polarization effects at higher charge rates, resulting in heterogeneous stress distributions across the anode. With the identification of critical failure parameters for both active particles and binder materials, offering novel insights for mitigating degradation in high-capacity electrode systems.

Amorphous silicon anode↗

Effects of ingested nanocellulose on intestinal microbiota and homeostasis in Wistar Han rats

Micron scale crystalline and fibrillar cellulose materials are “generally regarded as safe” (GRAS) as binders and thickeners in food products. Yet, partly due to a lack of relevant toxicological data, nanocellulose (NC) materials, which have unique properties that can be exploited to improve food quality and safety, have yet to receive FDA approval as food ingredients. Results of in vitro and in vivo toxicological studies of ingested NC, detailed in a recent companion report, revealed minimal acute in vitro cytotoxicity, and no toxicity in a subacute rat gavage model, suggesting that NC materials are non-hazardous. However, ingested materials may also modulate gut microbial populations, or alter aspects of intestinal function not evaluated in standard totoxicity testing, which could have important health implications. Here, we report the results of studies of the effects of ingested cellulose nanofibrils (CNF) on the fecal microbiome and metabolome, intestinal (ileal) epithelial cell mRNA expression of cell junction genes, and ileal cytokine production. Feces, plasma, and ileum samples were collected from Wistar Han rats before and after five weeks of biweekly gavages of water or cream, with or without 1% w/w CNF. Analysis of fecal microbial populations revealed that CNF caused changes in both genus and species diversity, with specific effects on species that produce short chain fatty acids, and that have been associated with increased IgA production and elevation of insulin levels. Fecal metabolomic analysis revealed relatively few effects of CNF, with significant changes in the levels of only ten metabolites out of 366 measured. Exposure to CNF also caused differential regulation of mRNA expression of several genes involved in epithelial cell junctions, and increased production of cytokines that both promote and inhibit proliferation of CD8 T cells. These perturbations in intestinal homeostasis contrast somewhat with the absence of in vitro and in vivo toxicity observed previously but would appear to represent minor effects. Additionally, the gut microbiome is highly sensitive to ingested substances, and such disturbances of the intestinal microbial ecosystem do not necessarily represent or predict meaningful pathology. Further studies, including chronic feeding studies, are needed to assess the real health implications, if any, of these changes.

59 BASIC BIOLOGICAL SCIENCES↗

Water-Based Electrode Manufacturing and Direct Recycling of Lithium-Ion Battery Electrodes—A Green and Sustainable Manufacturing System

It is critical to develop a low-cost and environmentally friendly system to manufacture and recycle lithium-ion batteries (LIBs) as the demand on LIBs keeps increasing dramatically. Conventional LIB cathodes are manufactured using N-methyl-2-pyrrolidone as the solvent, which is expensive, highly toxic, flammable, and energy intensive to produce and recover. Ideally, a close-loop industrial supply chain should be built, in which the batteries are manufactured, market harvested, and recycled with minimal external toxic solvent through the whole system. This work demonstrates a green and more sustainable manufacturing method for LIBs where no hazardous organic solvent is used during electrode manufacturing and recycling. The electrodes fabricated via water-based processing demonstrate comparable rate performance and cycle life to the ones from conventional solvent-based processing. Utilization of a water-soluble binder enables recovering the cathode compound from spent electrodes using water, which is successfully regenerated to deliver comparable electrochemical performance to the pristine one.

25 ENERGY STORAGE↗

Aluminum bonded SmCo5 magnets with enhanced mechanical strength

Despite their versatility and easy manufacturability, polymer-bonded magnets find limited application due to their limited mechanical properties and temperature resistance. In this study, we developed mechanically robust, aluminum-bonded SmCo5 magnets by utilizing a low-temperature, shear-assisted friction consolidation technique. Bonded magnets with varying magnetic phase content were fabricated at processing temperature of 500°C, and their microstructures, magnetic, mechanical, and electrical properties were systematically investigated. The resulting bonded-magnets showed effective consolidation with nanocrystalline microstructures. Magnetic properties were found to be tunable through variations in binder phase content, with coercivity reaching values up to 15.3 kOe (1217.5 kA/m) and maximum magnetic energy product up to 3.6 MGOe (28.7 kJ/m3), which are comparable to other bonded magnets. Electrical resistivities were lower than the polymer-bonded magnets, but comparable to the sintered ones. We observed an average flexural strength of 223 MPa for 60 vol.% SmCo5/Al sample, which is nearly two times higher than the reported values for sintered and bonded Sm-Co magnets. Our research demonstrated an effective approach to fabricate metal-bonded permanent magnets with superior magnetic and mechanical properties potentially applicable for high temperature applications.

Poudel Chhetri, Tej Bahadur↗

Dynamical behaviors of structural, constrained and free water in calcium- and magnesium-silicate-hydrate gels

We present the hypothesis that the mechanical properties of cement pastes depend strongly on their porosities. In a saturated paste, the porosity links to the free water volume after hydration. Structural water, constrained water, and free water have different dynamical behavior. Hence, it should be possible to extract information on pore system by exploiting the water dynamics. With our experiments we investigated the slow dynamics of hydration water confined in calcium- and magnesium-silicate-hydrate (C-S-H and M-S-H) gels using high-resolution quasi-elastic neutron scattering (QENS) technique. C-S-H and M-S-H are the chemical binders present in calcium rich and magnesium rich cements. We measured three M-S-H samples: pure M-S-H, M-S-H with aluminum-silicate nanotubes (ASN), and M-S-H with carboxyl group functionalized ASN (ASN-COOH). A C-S-H sample with the same water content (i.e. 0.3) is also studied for comparison. We found that structural water in the gels contributes to the elastic component of the QENS spectrum, while constrained water and free water contribute the quasi-elastic component. The quantitative analysis suggests that the three components vary for different samples and indicate the variance in the system porosity, which controls the mechanical properties of cement pastes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Decomposition of PVDF to delaminate cathode materials from end-of-life lithium-ion battery cathodes

The growing demand of electric vehicles and rapid consumption of rechargeable lithium-ion batteries (LIBs) require recycling of spent cathode active materials (CAMs) to reduce hazardous wastes and supply raw materials to LIB production. To separate CAMs from the cathode, direct calcination of polyvinylidene fluoride (PVDF) binder is widely applied, which leads to high energy consumption and release of toxic hydrogen fluoride. It is desirable to have an environmentally friendly and effective alternative to traditional direct calcination. In this study, five lithium salts, LiOAc (lithium acetate), LiNO 3 , LiCl, Li 2 CO 3 , and Li 2 SO 4 , were deployed and compared for their performance in recycling CAMs. A peel-off efficiency of up to 98.5% was achieved at a LiOAc to LiNO 3 molar ratio of 3:2, salt to cathode mass ratio of 10:1, and temperature of 300 °C at a holding time of 30 min. This system avoids corrosive chemicals and minimizes particle agglomeration of recycled products. Compared with sodium salt systems (NaOAc-NaNO 3 ) or direct calcination, the LiOAc-LiNO 3 system prevented high reaction temperature or further lithium loss and minimized crystal structure and morphological changes. In conclusion, a decomposition mechanism of PVDF through adsorption of HF and fluorine substitution was proposed.

25 ENERGY STORAGE↗

Numerical study of a stochastic particle algorithm solving a multidimensional population balance model for high shear granulation

This paper is concerned with computational aspects of a multidimensional population balance model of a wet granulation process. Wet granulation is a manufacturing method to form composite particles, granules, from small particles and binders. A detailed numerical study of a stochastic particle algorithm for the solution of a five-dimensional population balance model for wet granulation is presented. Each particle consists of two types of solids (containing pores) and of external and internal liquid (located in the pores). Several transformations of particles are considered, including coalescence, compaction and breakage. A convergence study is performed with respect to the parameter that determines the number of numerical particles. Averaged properties of the system are computed. In addition, the ensemble is subdivided into practically relevant size classes and analysed with respect to the amount of mass and the particle porosity in each class. These results illustrate the importance of the multidimensional approach. Finally, the kinetic equation corresponding to the stochastic model is discussed.

97 MATHEMATICS AND COMPUTING↗

Direct ink writing of boron carbide monoliths

Direct ink writing – an extrusion-based additive manufacturing process – followed by pressureless sintering was investigated to produce boron carbide monoliths. The effects of ceramic powder loading and Pluronic binder concentration on the rheology of boron carbide pastes were studied and linked to both processing behaviour and final outcome in terms of sintered density and hardness. The effects of printing parameters, in particular orifice diameter and printing speed, were also investigated. Reducing the size of the extrusion nozzle from 584 μm to 406 μm led to significantly better shape retention, lower surface roughness, as well as higher density and hardness. A 203 μm printing orifice was also trialled but was unsuccessful due to faster drying kinetics that occurred with smaller ceramic struts resulting in rapid warping and nozzle clogging. Carbon-black – 8 wt% relative to B 4 C – acted as an effective sintering aid to increase both density and hardness. After optimisation of feedstock and printing parameters, few-layer samples (3–5 layers) had a density as high as ~ 97 % TD and a hardness of ~ 30 GPa. On the other hand, 18-layer specimens had a sintered density of ~ 87 % TD, despite a fully dense microstructure, due to the formation of a 3D array of inter-strut pores. Nevertheless, several issues that arose during manufacturing and post-processing were detrimental to the density and structural integrity of printed specimens; these issues were identified, discussed, and suggestions for future work are provided in this report.

36 MATERIALS SCIENCE↗

Laser-induced slip casting as an additive manufacturing approach for silicon carbide

Here, this work presents processing silicon carbide (SiC) with the laser-induced slip casting (LIS) additive manufacturing (AM). SiC was stabilized in water with polyethyleneimine (PEI) dispersant, and SiC slurries were made with rheology for LIS printing. High-density ceramic parts were printed, followed by single-step binder burnout and sintering. The printed parts achieved 93–95 % of theoretical density. X-ray computed tomography (XCT) revealed a small distribution of flaws exceeding 100 microns. The mechanical properties were measured in both parallel and perpendicular to the printing layers, and the orientation with layers perpendicular to the bending moment resulted in higher strength compared to the parallel direction. Porosity resulting from processing and large inclusions of boron carbide (B4C) were the root cause of failure in the measured samples. Despite these defects through this effort, this new approach demonstrates promise for green forming of SiC with densities greater than 95 % theoretical and tensile strengths above 250 MPa.

Additive Manufacturing↗

Process-level cost analysis of hybrid manufacturing pathways for aerospace structural components

Hybrid manufacturing is a promising route for producing complex aerospace components, yet systematic cost benchmarking across multiple additive-subtractive pathways remains limited. This study presents a comprehensive process-based cost analysis of seven hybrid manufacturing routes, including laser powder bed fusion (L-PBF), powder- and wire-directed energy deposition (DED), wire arc additive manufacturing (WAAM), additive friction stir deposition (AFSD), metal binder jetting (MBJ), and agility forging, followed by scanning and finish machining. Parametric cost models incorporating direct material, labor, and energy costs were developed. L-PBF results are discussed in detail for a pickle fork component and directly compared with commercial pricing. Across all hybrid routes, labor emerged as the dominant cost driver, contributing more than 70% of total manufacturing cost in some cases. AFSD exhibited the lowest cost for aluminum components, with MBJ being its 316 L stainless steel counterpart, after accounting for geometric scaling. Benchmarking against industrial quotes suggests that hybrid manufacturing can achieve cost levels comparable to those of commercial services, although labor-intensive processes exhibit greater deviation. The analysis highlights automation of material handling, setup, and supervision as key opportunities for improving economic competitiveness. Overall, the proposed framework provides a quantitative basis for evaluating and optimizing hybrid manufacturing pathways for aerospace applications.

Baruah, Sweta [ORNL] (ORCID:0009000174256207)↗

Dimerization Controls Marburg Virus VP24-dependent Modulation of Host Antioxidative Stress Responses

Marburg virus (MARV), a member of the Filoviridae family that also includes Ebola virus (EBOV), causes lethal hemorrhagic fever with case fatality rates that have exceeded 50% in some outbreaks. Within an infected cell, there are numerous host-viral interactions that contribute to the outcome of infection. Recent studies identified MARV protein 24 (mVP24) as a modulator of the host antioxidative responses, but the molecular mechanism remains unclear. Using a combination of biochemical and mass spectrometry studies, we show that mVP24 is a dimer in solution that directly binds to the Kelch domain of Kelch-like ECH-associated protein 1 (Keap1) to regulate nuclear factor (erythroid-derived 2)-like 2 (Nrf2). This interaction between Keap1 and mVP24 occurs through the Kelch interaction loop (K-Loop) of mVP24 leading to upregulation of antioxidant response element transcription, which is distinct from other Kelch binders that regulate Nrf2 activity. N-terminal truncations disrupt mVP24 dimerization, allowing monomeric mVP24 to bind Kelch with higher affinity and stimulate higher antioxidative stress response element (ARE) reporter activity. Mass spectrometry-based mapping of the interface revealed overlapping binding sites on Kelch for mVP24 and the Nrf2 proteins. Substitution of conserved cysteines, C209 and C210, to alanine in the mVP24 K-Loop abrogates Kelch binding and ARE activation. Furthermore, our studies identify a shift in the monomer-dimer equilibrium of MARV VP24, driven by its interaction with Keap1 Kelch domain, as a critical determinant that modulates host responses to pathogenic Marburg viral infections.

59 BASIC BIOLOGICAL SCIENCES↗

A novel method combining additive manufacturing and alloy infiltration for NdFeB bonded magnet fabrication

In this paper, binder jetting additive manufacturing technique is employed to fabricate NdFeB isotropic bonded magnets, followed by an infiltration process with low-melting point eutectic alloys [i.e., Nd 3 Cu 0.25 Co 0.75 (NdCuCo) and Pr 3 Cu 0.25 Co 0.75 (PrCuCo)]. Densification and mechanical strength improvement are achieved for the as-printed porous part. Meanwhile, the intrinsic coercivity H ci is enhanced from 732 to 1345 kA/m and 1233 kA/m after diffusion of NdCuCo and PrCuCo, respectively. This study presents a novel method for fabricating complex-shaped bonded magnets with promising mechanical and magnetic properties.

36 MATERIALS SCIENCE↗

Effects of magnetic field annealing on the hard magnetic properties of milled Nd-Fe-B powders

In this study, we report the effect of magnetic field annealing (MA) in relieving the stress induced during the milling of Nd-Fe-B sintered magnets. The effect of MA processing parameters and particle size on the magnetic properties were investigated. Based on the results, magnetic field annealing is more effective in improving the magnetic properties of larger size particles, compared to finer particles. Our computational study on the role of particle surface defects in bi-modal particle distribution agrees with results obtained experimentally. In conclusion, magnetic field annealed powder has been successfully used to develop 4.6 g.cm -3 density bonded magnets with 75 vol% of magnetic powder and polyamide 12 (nylon 12) polymer binder resulting in 11.3 MGOe energy product.

36 MATERIALS SCIENCE↗

Recycling of additively printed anisotropic Nd-Fe-B bonded magnets

A high potential cost-effective and environmentally friendly method has been applied for recycling anisotropic Nd-Fe-B bonded magnets. Waste additively printed Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) Nd-Fe-B anisotropic bonded magnet was pulverized into composite powder containing Nd-Fe-B particles and nylon binder through cryomilling at a liquid nitrogen temperature (~77 K) under Ar inert atmosphere. Then, the cryomilled composite powder was warm compacted into a bonded magnet. Further, the magnetic particles were aligned during post-compaction annealing under a magnetic field of 30 kOe. The recycled bonded magnets have a higher density (3% enhancement), but slightly inferior magnetic properties compared to the original magnets, i.e., the magnetic remanence, coercivity and maximum energy product are reduced by 2%, 3% and 8%, respectively. The scanning electron microscopy revealed that some HDDR Nd-Fe-B powder crumbled into fine particles during cryomilling. Powder X-ray diffraction showed a small amount of Nd-oxide impurity in the cryomilled powder. The slightly deteriorated magnetic properties are ascribed to the oxidation of Nd-Fe-B particles due to formation of fresh fracture surface during cryomilling. The approach enables the direct reuse of end-of-life bonded magnets in an economical and environmentally friendly way.

36 MATERIALS SCIENCE↗