Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “anodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Thermal characteristics of Lithium-ion batteries

Lithium-ion batteries have a very promising future for space applications. Currently they are being used on a few GEO satellites, and were used on the two recent Mars rovers Spirit and Opportunity. There are still problem that exist that need to be addressed before these batteries can fully take flight. One of the problems is that the cycle life of these batteries needs to be increased. battery. Research is being focused on the chemistry of the materials inside the battery. This includes the anode, cathode, and the cell electrolyte solution. These components can undergo unwanted chemical reactions inside the cell that deteriorate the materials of the battery. During discharge/ charge cycles there is heat dissipated in the cell, and the battery heats up and its temperature increases. An increase in temperature can speed up any unwanted reactions in the cell. Exothermic reactions cause the temperature to increase; therefore increasing the reaction rate will cause the increase of the temperature inside the cell to occur at a faster rate. If the temperature gets too high thermal runaway will occur, and the cell can explode. The material that separates the electrode from the electrolyte is a non-conducting polymer. At high temperatures the separator will melt and the battery will be destroyed. The separator also contains small pores that allow lithium ions to diffuse through during charge and discharge. High temperatures can cause these pores to close up, permanently damaging the cell. My job at NASA Glenn research center this summer will be to perform thermal characterization tests on an 18650 type lithium-ion battery. High temperatures cause the chemicals inside lithium ion batteries to spontaneously react with each other. My task is to conduct experiments to determine the temperature that the reaction takes place at, what components in the cell are reacting and the mechanism of the reaction. The experiments will be conducted using an accelerating rate calorimeter (ARC), which uses a heat-wait-search mode until an exothermic reaction is detected. After an exotherm is found the calorimeter maintains an adiabatic environment around a bomb which holds the test sample. The ARC will help identify important reactions and what temperature these exothermic reactions take place at. In order fully understand the battery, we are first going to take apart the battery and test the individual components of the battery using the ARC. I will first conduct a test on the electrolyte solution by itself. We will then test the electrolyte solution with the anode. We would like to see how the electrolyte solution reacts with the anode and its binder material. The next would be the same test using the cathode instead of the anode. By comparing the results of the electrolyte, electrolyte with anode, and the electrolyte with the cathode we can determine the reactions that are taking place due to each component. Using the heat capacity of the each individual sample and the temperature by which the sample increases, kinetic and thermo-dynamical information can then be found. A Gas chromatograph could be used to help with the task of identifying the by-products at the end of each test. One way of increasing the cycle life is to increase the stability of the materials inside the

Hauser, Dan↗
NASA NTRS1997

Polymer membrane based electrolytic cell and process for the direct generation of hydrogen peroxide in liquid streams

An electrolytic cell for generating hydrogen peroxide is provided including a cathode containing a catalyst for the reduction of oxygen, and an anode containing a catalyst for the oxidation of water. A polymer membrane, semipermeable to either protons or hydroxide ions is also included and has a first face interfacing to the cathode and a second face interfacing to the anode so that when a stream of water containing dissolved oxygen or oxygen bubbles is passed over the cathode and a stream of water is passed over the anode, and an electric current is passed between the anode and the cathode, hydrogen peroxide is generated at the cathode and oxygen is generated at the anode.

White, James H.↗
NASA NTRS2006

Method for manufacturing high quality carbon nanotubes

A non-catalytic process for the production of carbon nanotubes includes supplying an electric current to a carbon anode and a carbon cathode which have been securely positioned in the open atmosphere with a gap between them. The electric current creates an electric arc between the carbon anode and the carbon cathode, which causes carbon to be vaporized from the carbon anode and a carbonaceous residue to be deposited on the carbon cathode. Inert gas is pumped into the gap to flush out oxygen, thereby preventing interference with the vaporization of carbon from the anode and preventing oxidation of the carbonaceous residue being deposited on the cathode. The anode and cathode are cooled while electric current is being supplied thereto. When the supply of electric current is terminated, the carbonaceous residue is removed from the cathode and is purified to yield carbon nanotubes.

Benavides, Jeanette M.↗
NASA NTRS2010

Direct Electrolysis of Molten Lunar Regolith for the Production of Oxygen and Metals on the Moon

When considering the construction of a lunar base, the high cost ($ 100,000 a kilogram) of transporting materials to the surface of the moon is a significant barrier. Therefore in-situ resource utilization will be a key component of any lunar mission. Oxygen gas is a key resource, abundant on earth and absent on the moon. If oxygen could be produced on the moon, this provides a dual benefit. Not only does it no longer need to be transported to the surface for breathing purposes; it can also be used as a fuel oxidizer to support transportation of crew and other materials more cheaply between the surface of the moon, and lower earth orbit (approximately $20,000/kg). To this end a stable, robust (lightly manned) system is required to produce oxygen from lunar resources. Herein, we investigate the feasibility of producing oxygen, which makes up almost half of the weight of the moon by direct electrolysis of the molten lunar regolith thus achieving the generation of usable oxygen gas while producing primarily iron and silicon at the cathode from the tightly bound oxides. The silicate mixture (with compositions and mechanical properties corresponding to that of lunar regolith) is melted at temperatures near 1600 C. With an inert anode and suitable cathode, direct electrolysis (no supporting electrolyte) of the molten silicate is carried out, resulting in production of molten metallic products at the cathode and oxygen gas at the anode. The effect of anode material, sweep rate, and electrolyte composition on the electrochemical behavior was investigated and implications for scale-up are considered. The activity and stability of the candidate anode materials as well as the effect of the electrolyte composition were determined. Additionally, ex-situ capture and analysis of the anode gas to calculate the current efficiency under different voltages, currents and melt chemistries was carried out.

Sirk, Aislinn H. C.↗
NASA NTRS2015

Proof-of-Concept Experiments on a Gallium-Based Ignitron for Pulsed Power Applications

Ignitrons are electrical switching devices that operate at switching times that are on the order of microseconds, can conduct high currents of thousands of amps, and are capable of holding off tens of thousands of volts between pulses. They consist of a liquid metal pool within an evacuated tube that serves both the cathode and the source of atoms and electrons for an arc discharge. Facing the liquid metal pool is an anode suspended above the cathode, with a smaller ignitor electrode tip located just above the surface of the cathode. The ignitron can be charged to significant voltages, with a potential difference of thousands of volts between anode and cathode. When an ignition pulse is delivered from the ignitor electrode to the cathode, a small amount of the liquid metal is vaporized and subsequently ionized, with the high voltage between the anode and cathode causing the gas to bridge the gap between the two electrodes. The electrons and ions move rapidly towards the anode and cathode, respectively, with the ions liberating still more atoms from the liquid metal cathode surface as a high-current plasma arc discharge is rapidly established. This arc continues in a self-sustaining fashion until the potential difference between the anode and cathode drops below some critical value. Ignitrons have been used in a variety of pulsed power applications, including the railroad industry, industrial chemical processing, and high-power arc welding. In addition, they might prove useful in terrestrial power grid applications, serving as high-current fault switches, quickly shunting dangerous high-current or high-voltage spikes safely to ground. The motivation for this work stemmed from the fact that high-power, high-reliability, pulsed power devices like the ignitron have been used for ground testing in-space pulsed electric thruster technologies, and the continued use of ignitrons could prove advantageous to the future development and testing of such thrusters. Previous ignitron designs have used mercury as the liquid metal cathode, owing to its presence as a liquid at room temperatures and a vapor pressure of 10 Pa (75 mtorr) at room temperature. While these are favorable properties, there are obvious environmental and personal safety concerns with the storage, handling, and use of mercury and its compounds. The purpose of the present work was to fabricate and test an ignitron that used as its cathode an alternate liquid metal that was safe to handle and store. To that end, an ignitron test article that used liquid gallium as the cathode material was developed and tested. Gallium is a metal that has a melting temperature of 29.76 C, which is slightly above room temperature, and a boiling point of over 2,300 C at atmospheric pressure. This property makes gallium the element with the largest relative difference between melting and boiling points. Gallium has a limited role in biology, and when ingested, it will be subsequently processed by the body and expelled rather than accumulating to toxic levels. The next section of this Technical Memorandum (TM) provides background information on the development of mercury-based ignitrons, which serves as the starting point for the development of the gallium-based variant. Afterwards, the experimental hardware and setup used in proof-of-concept testing of a basic gallium ignitron are presented. Experimental data, consisting of discharge voltage and current waveforms as well as high-speed imaging of the gallium arc discharge in the gallium ignitron test article, are presented to demonstrate the efficacy of the concept. Discussion of the data and suggestions on improvements for future iterations of the design are presented in the final two sections of this TM.

Ali, H. K.↗
NASA NTRS2015

SiLix-C Nanocomposites

For this Phase II project, Superior Graphite Co., in collaboration with the Georgia Institute of Technology and Streamline Nanotechnologies, Inc., developed, explored the properties of, and demonstrated the enhanced capabilities of novel nanostructured SiLix-C anodes. These anodes can retain high capacity at a rapid 2-hour discharge rate and at 0 C when used in Li-ion batteries. In Phase I, these advanced anode materials had specific capacity in excess of 1,000 mAh/g, minimal irreversible capacity losses, and stable performance for 20 cycles at C/1. The goals in Phase II were to develop and apply a variety of novel nanomaterials, fine-tune the properties of composite particles at the nanoscale, optimize the composition of the anodes, and select appropriate binder and electrolytes. In order to achieve a breakthrough in power characteristics of Li-ion batteries, the team developed new nanostructured SiLix-C anode materials to offer up to 1,200 mAh/g at C/2 at 0 C.

Henry, Francois↗
NASA NTRSDate not supplied

A METHOD TO REDUCE BIOBURDEN IN ASTROMATERIALS CURATION FACILITIES WITHOUT INTRODUCING UNWANTED CONTAMINATION

Introduction: NASA curates its Astromaterials collections in cleanrooms that are carefully monitored for particulate, inorganic and trace metal contamination. Current sample collections are not particularly susceptible to organic contamination or biological alteration. However, new collections like those from the OSIRIS-REx and Hayabusa2 missions will have organic contamination requirements and are susceptible to biodegradation. It will be necessary sterilize or at least disinfect curation labs, as well as tools and equipment in a manner that does not introduce additional contamination and does not affect the samples 1. Current curation cleaning procedures utilize isopropyl alcohol which offers some bioburden reduction, but is not effective against spore-forming bacteria or fungal spores 2. We present a modified disinfection method that uses ultrapure hydrogen peroxide to reduce bioburden inside curation labs and glove boxes without introducing contamination or damaging curation equipment. We tested this method in the meteorite processing lab as well as on a glovebox being cleaned for use in processing ANGSA (Apollo Next Generation Sample Analysis) samples and present the results of those tests. We discuss the limitations of this method and describe potential situations in which it will not be applicable. The CDC guidelines for disinfection andsterilization in healthcare facilities discusses over 15different methods for reducing bioburden in hospitalsettings 3. The most common method, steamsterilization, is well suited to sterilizing curationprocessing tools but cannot easily be used to sterilizecleanroom surfaces or large equipment likegloveboxes. Chemical sterilization with bleach(NaOCl) is also a common strategy in healthcare andpharmaceutical settings that presents materialcompatibility issues as well as serious inorganiccontamination concerns for curation facilities.Introducing a new source of Na and Cl into curationlabs is not acceptable. Other chemical methods likeethylene oxide, formaldehyde, iodophors andquaternary ammonium compounds could introduceorganic and inorganic contamination. We chose tofocus on hydrogen peroxide because it is generallycompatible with commonly used curation materialslike stainless steel, aluminum and Teflon and becauseit decomposes to oxygen and water. The CDCguidelines for hydrogen peroxide specify using a 7.5wt% solution at 25 ̊C with a contact time of 30 minutesfor high level disinfection and 6 hours for sterilization.High level disinfection is defined as a technique thatwill kill all microorganisms except large numbers ofbacterial spores 3. Methods: We prepared a solution of 7.5 wt%hydrogen peroxide from a stock solution of ultrapure30 wt% peroxide (JT Baker) and curation gradeultrapure water. This ultrapure water is already used incuration cleaning procedures and thus is not consideredand additional source of contamination. We conducteda materials compatibility test by exposing unanodizedand anodized 6061 T6 Al alloy to the peroxide solutionfor up to six hours and periodically inspecting thesurfaces for visible defects. We used this peroxide todisinfect the floor of the meteorite processing lab andthe interior of a curation glovebox by exposing thesesurfaces to the peroxide solution for 30 min. Thesurfaces were swabbed with a dry macrofoam swabbefore (Puritan Brand 2518051PFRNDFD) and afterperoxide treatment to collect microbes present on thesurfaces. Microbes were extracted by sonication fromthe swab into 15 ml of PBS (phosphate buffered saline)and inoculated onto the following media: TSA (trypticsoy agar) BA (blood agar), R2A (Reasoners 2 agar),Potato Dextrose Agar, Saboraud Dextrose Agar andSaboraud Dextrose Agar with 0.1 mg/ mlchloramphenicol. Four TSA plates and two BA plateswere inoculated with 0.1 ml of PBS each andincubated at 35 and 37 for 48 hours. Two R2A°C°Cplates (0.1 ml of PBS each) were incubated at 25 .°CThe remaining plates were inoculated with 0.2ml ofPBS and incubated at 30 ̊C for seven days. Afterincubation bacterial and fungal isolates were countedand transferred to new plates for identification usingthe VITEK24 automated system or by sequencing aportion of the barcode gene (16S rRNA for bacteria,small subunit gene for fungi) on an ABI 3500 Sangersequencer. Negative controls consisted of swabs thatwere opened in the sampling environment andanalyzed alongside the experimental samples.Results: A 6 hour exposure to hydrogen peroxideresulted in visible pitting on un-anodized 6061 Al, butnot on anodized surfaces. No visible pitting occurredafter a 30 minute exposure. Therefore, we decided tolimit our experimental tests to 30 min. exposures. 17bacterial CFU (colony forming units) representing 4distinct organisms were isolated from the meteorite processing lab floor prior to hydrogen peroxidetreatment. We were unable culture any organisms afterperoxide treatment. In the glovebox we were able toculture three bacterial CFU representing three distinctspecies, including a spore forming bacterium prior todisinfection with peroxide. After the peroxidetreatment we were unable to culture any organisms.Routine monitoring of the meteorite processing lab andthe glovebox did not indicate any increase in unwantedinorganic contamination after these peroxidetreatments. Discussion: A 30 minute treatment with 7.5 wt%peroxide appears to be an effective method forreducing bioburden on typical cleanroom surfaces. Themethod does not introduce unwanted organic orinorganic contamination and is compatible withcommonly used curation materials like stainless steel,Teflon and anodized aluminum alloys. Special careshould be taken with un-anodized aluminum.Prolonged exposure to hydrogen peroxide can causepitting on this material. We recommend using thismethod to disinfect curation labs and equipment whenbiological alteration is a concern. This method iseffective at room temperature and cannot be used todisinfect labs and equipment where the ambienttemperature is < 0 ̊C. Astromaterials samples shouldbe removed from the area where disinfection is tooccur. Hydrogen peroxide is a powerful oxidizingagent and will react with any organic carbon present inthe sample. References: [1.] Mccubbin, F. M. et al.Sp. Sci Rev(2019) doi:10.1007/s11214-019-0615-9. [2.] Mogul, R.et al.Astrobiology 18, ast.2017.1814 (2018). [3.]Rutala, W. A. & Weber, D. J. Guideline for Disinfection and Sterilization in Healthcare Facilities, 2008. [4.] Pincus, D. H. in Encyclopedia of Rapid Microbiological Methods (2005).

A. B. Regberg↗
DOE OSTI2021

Flow-regulated growth of nanotubes

A method for growing nanotubes via flow-regulated microfluidic electrochemical anodization, includes providing a microfluidic device having a fluid inlet; a fluid outlet; and a fluidic microchannel connecting the fluid inlet and outlet, wherein the microchannel includes a Pt cathode and a Ti anode separated by an electrical insulator; providing an electrolyte fluid flow through the microchannel; and providing an electrical current across the anode and cathode sufficient to cause electrochemical anodization growth of TiO2 nanotubes in the microchannel on a surface of the anode.

Wan, Jiandi↗
DOE OSTI2021

High efficiency electrolytes for high voltage battery systems

Disclosed herein are embodiments of an electrolyte that is stable and efficient at high voltages. The electrolyte can be used in combination with certain cathodes that exhibit poor activity at such high voltages with other types of electrolytes and can further be used in combination with a variety of anodes. In some embodiments, the electrolyte can be used in battery systems comprising a lithium cobalt oxide cathode and lithium metal anodes, silicon anodes, silicon/graphite composite anodes, graphite anodes, and the like.

Ren, Xiaodi↗
DOE OSTI2021

Vapor phase photo-electrochemical cell

This disclosure provides systems, methods, and apparatus related to a vapor phase photo-electrochemical cell. In one aspect, a device includes a photovoltaic cell, a cathode disposed on the photovoltaic cell, an ionomer membrane disposed on the cathode, and an anode disposed on the ionomer membrane. The cathode includes a cathode catalyst. The ionomer membrane is in contact with the cathode catalyst. The anode includes an anode catalyst. The anode catalyst is in contact with the ionomer membrane. The anode, the ionomer membrane, and the cathode are transmissive to the solar radiation spectrum.

Larson, David M.↗
DOE OSTI2023

Methods and systems for diagnosis of failure mechanisms and for prediction of lifetime of metal batteries

Methods for diagnosing failure mechanisms and for predicting lifetime of metal batteries include monitoring rest voltage and Coulombic Efficiency over relatively few cycles to provide profiles that indicate, by the trends thereof, a particular failure mechanism (e.g., electrolyte depletion, loss of metal inventory, increased cell impedance). The methods also include cycling over relatively few cycles an anode-free cell, having the same cathode and electrolyte as the metal battery, but with a current collector instead of the anode. Discharge capacity is monitored and profiled, and a discharge capacity curve is fitted to the discharge capacity profile to discern a capacity retention per cycle. The lifetime of the metal battery is determined using the capacity retention per cycle discerned from the anode-free cell. Related systems include a metal-based battery and an anode-free cell or a battery cell reconfigurable between a metal-based and an anode-free cell.

Li, Bin↗
DOE OSTI2025

Examples of X-Ray Characterization Techniques in Energy Storage Research

Lithium-ion batteries have revolutionized the portable electronics and transportation sectors. Their performance is often critically dependent on the crystal structures of the anode and cathode electrode materials, which must enable the transport and reversible storage of lithium ions into and out of the lattice. Because lithium is a low-Z element, characterization of materials for lithium-ion batteries can be particularly challenging. Regardless, X-ray techniques enable analysis of material structures to better understand how battery materials perform and degrade, particularly when combined with other materials characterization and electrochemical characterization techniques. While X-ray techniques are most often used in battery research for phase identification of crystal structures, X-ray characterization techniques are also used for a wide variety of other purposes. I will discuss several examples from my research with various collaborators on several projects that highlight the impact that X-ray characterization techniques can have on battery research. The first example will focus on low-temperature microwave-assisted solvothermal synthesis of vanadium-doped LiFePO4 cathode materials for lithium-ion batteries. (1,2) Through a combination of electrochemical and materials characterization, we determined that low temperature synthesis resulted in metastable phases that enabled incorporation of higher dopant levels than resulting from high-temperature synthesis of thermodynamically stable phases. Rietveld refinement of X-ray diffraction data enabled understanding of how lattice parameters changed with doping levels and synthesis temperature. X-ray absorption near edge spectroscopy enabled understanding of the vanadium and iron oxidation states to confirm how vacancies in the structure caused by doping were charge compensated. This was important to understand because the literature suggests doping can improve LiFePO4 electrical conductivity, which improves battery charge and discharge rates. The second example will focus on understanding residual strain in lithium metal anodes. Lithium-ion batteries typically use graphite anodes, but the charge-storage capacity can be theoretically improved ~10x by using lithium metal as the anode material instead. However, lithium anodes suffer from growth of high-aspect-ratio features, such as dendrites, that can pierce nanoporous polymer separators and lead to short circuits and fires. External pressure is commonly applied to cells to enable better morphological control. We hypothesized that applied pressure may promote strain and possibly work hardening during electrochemical cycling, which motivated us to look for evidence of residual strain in lithium metal cycled under applied pressure using X-ray diffraction and sin2(..psi..) analysis. We found that lithium electrodeposited under high pressure exhibited in-plane compressive strain and that that lithium electrodeposited under low pressure did not. (3) The residual strain that accompanies electrodeposition under high pressure may lead to work hardening, which may explain how a soft metal like lithium can puncture separators and why higher pressure does not always decrease short circuits. (4-6) References: 1) Harrison, K. L.; Manthiram, A. Microwave-Assisted Solvothermal Synthesis and Characterization of Metastable LiFe1- x (VO) x PO4 Cathodes. Inorganic chemistry 2011, 50(8), 3613-3620. 2) Harrison, K. L.; Bridges, C. A.; Paranthaman, M. P.; Segre, C. U.; Katsoudas, J.; Maroni, V. A.; Idrobo, J. C.; Goodenough, J. B.; Manthiram, A. Temperature Dependence of Aliovalent-Vanadium Doping in LiFePO4 Cathodes. Chemistry of Materials 2013, 25(5), 768-781. 3) Rodriguez, M. A.; Harrison, K. L.; Goriparti, S.; Griego, J. J.; Boyce, B. L.; Perdue, B. R. Use of a Be-Dome Holder for Texture and Strain Characterization of Li Metal Thin Films via Sin2 (..psi..) Methodology. Powder Diffraction 2020, 35(2), 89-97. 4) Jungjohann, K. L.; Gannon, R. N.; Goriparti, S.; Randolph, S. J.; Merrill, L. C.; Johnson, D. C.; Zavadil, K. R.; Harris, S. J.; Harrison, K. L. Cryogenic Laser Ablation Reveals Short-Circuit Mechanism in Lithium Metal Batteries. ACS Energy Letters 2021, 6(6), 2138-2144. 5) Harrison, K. L.; Merrill, L. C.; Long, D. M.; Randolph, S. J.; Goriparti, S.; Christian, J.; Warren, B.; Roberts, S. A.; Harris, S. J.; Perry, D. L. Cryogenic Electron Microscopy Reveals That Applied Pressure Promotes Short Circuits in Li Batteries. Iscience 2021, 24(12). 6) Harrison, K. L.; Goriparti, S.; Merrill, L. C.; Long, D. M.; Warren, B.; Roberts, S. A.; Perdue, B. R.; Casias, Z.; Cuillier, P.; Boyce, B. L. Effects of Applied Interfacial Pressure on Li-Metal Cycling Performance and Morphology in 4 M LiFSI in DME. ACS Applied Materials & Interfaces 2021, 13(27), 31668-31679.

batteries↗
DOE OSTI2022

Long–Cycling Sulfide–Based All–Solid–State Batteries Enabled by Electrochemo–Mechanically Stable Electrodes

Anode significantly determines the energy density of all-solid-state Lithium batteries (ASLBs). Silicon (Si) and Lithium (Li) metal are two of the most attractive anodes because of their ultrahigh theoretical capacities. However, most investigations focus on Li metal; the great potential of Si is underrated. This study investigates Si anode's stability, processability, and cost in ASLBs and compares them with Li metal. Moreover, the single-crystal LiNi 0.8 Co 0.1 Mn 0.1 O 2 is stabilized with a lithium silicate (Li 2 SiO x ) through a scalable sol-gel method. ASLBs with a cell-level energy density of 285 Wh kg -1 are obtained through sandwiching Si anode, thin sulfide solid-state electrolyte membrane, and interface stabilized LiNi 0.8 Co 0.1 Mn 0.1 O 2 . The full cell delivered a high capacity of 145 mAh g -1 at C/3 and maintained stability for 1000 cycles. This work inspires commercializing the ASLBs on a large scale with exciting manufacturing lines for large-scale, safe, and economical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2021

A Self-Healable Sulfide/Polymer Composite Electrolyte for Long-Life, Low-Lithium-Excess Lithium-Metal Batteries

Solid electrolyte-protected lithium-metal anodes promise energy-dense, safe cells. While sulfide solid electrolytes enable facile processability and fast ion transport, they suffer from complex chemo-mechanical issues, including Li plating-induced fracture and Li stripping-induced contact loss. To address these issues, a grafting approach is implemented to functionalize the sulfide solid electrolyte (Li 3,85 Sn 0.85 Sb 0.15 S 4 ) with a self-healing unit. This leads to a dynamic bonding between the solid electrolyte network and a mechanically robust polymer scaffold, which reversibly accommodates the volume changes of the lithium-metal anode. Thus, the approach improves the interfacial contact between the lithium-metal anode and the composite electrolyte, enabling stable cycling at a mild stack pressure (160 kPa). With a negative to positive capacity ratio equals to 1, pouch full cells with a high-nickel cathode (nickel content > 90%) and lithium-metal anode display 92% capacity retention for 140 cycles. Engineering the interface between solid electrolyte and the polymeric binder offers a promising pathway to address the chemo-mechanical issues.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Single‐Step Deformation Processing of Ultrathin Lithium Foil and Strip

Abstract Next‐generation, high‐efficiency energy storage and conversion systems require development of lithium metal batteries. But the high cost of production and constraints on thickness of lithium (anode) foils continue to limit adoption for integration into battery cell architectures. Here, a novel lithium anode manufacturing solution is demonstrated – single‐step production of ultrathin gauge foil formats directly from solid ingot. Hybrid cutting‐based deformation processes, involving large plastic strains and strain rates, produce foil to sub‐10 µm thickness, with surface quality even superior to present Li anode processing routes. Energy analysis shows the single‐stage processing is ≈50% more efficient than conventional processing by extrusion‐rolling. Through in situ force measurements and high‐speed imaging of the cutting it also characterize – for the first time – the flow stress of Li to strain rates of 800 sec −1 , revealing a power‐law relationship. The results present a paradigm shift in manufacturing and integration of solid lithium anodes for energy applications.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Operating High-Energy Lithium-Metal Pouch Cells with Reduced Stack Pressure Through a Rational Lithium-Host Design

Transitioning from a liquid electrolyte to an inorganic solid electrolyte offers a potential pathway to enable highly reversible lithium-metal anodes. However, the solid-electrolyte-protected lithium-metal anode suffers from poor interfacial ionic contacts and requires an impractically high stack pressure (>1.0 MPa) to maintain the interfacial contacts. It is demonstrated here that combining a hollow silver/carbon fiber scaffold and an inorganic/organic composite electrolyte enables a highly reversible lithium-metal anode. Since the high surface area of the electrode provides intimate contact and the hollow structure of the electrode relieves the lithium plating-induced stress, the electrode/electrolyte interface remains stable during cycling even under mild stack pressure. This unconventional structural design is validated in practical pouch cells assembled with the 3D lithium host containing a onefold excess of lithium and a high-nickel cathode. At a mild stack pressure of 320 kPa, the pouch cell displays 83% capacity retention for 200 cycles. This work illustrates that combining a hollow electrode architecture and a robust solid electrolyte offers a practical pathway toward rechargeable lithium-metal anodes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sequential separation of battery electrode materials and metal foils in aqueous media

To recycle high-value lithium-ion battery components, it is imperative to efficiently separate electrode materials from current collector foils and to separate cathodes from anodes. This study investigates the delamination behaviors of cathodes and anodes from their respective current collectors in aqueous media. Whereas anode films can easily detach from copper foils in water, the delamination of cathode films does not exhibit the same behavior in water; instead, the cation exchange reaction results in lithium leaching and aluminum corrosion in the presence of water. Here, a buffer solution with surfactant additives has been designed to prevent aluminum corrosion and to improve solution wetting behavior, thereby facilitating cathode delamination. The delamination difference enables the sequential recovery of electrode materials and metal foils at different separation stages, simplifying the traditionally intricate processes within a one-pot recovery system. The recovered materials retain their crystal structure and morphology, and there are no signs of aluminum corrosion or residues on the metal foils. The sequential separation technique achieves nearly 100% separation efficiency for electrode materials from metal foils and over 98% separation efficiency for cathode and anode materials.

25 ENERGY STORAGE↗
DOE OSTI2022

Combined Effects of Uniform Applied Pressure and Electrolyte Additives in Lithium-Metal Batteries

The development of lithium-metal batteries with good performance and long lifetimes requires fundamental insight into the mechanisms underlying performance improvements from individual design strategies and the interactions between multiple improvement approaches. Here, in this work, we investigated the individual and combined effects of applied pressure and a LiAsF 6 electrolyte additive on the performance of anode-free lithium-metal batteries; we employed various pressure application methods, which vary both in magnitude and uniformity. Both approaches individually improve cycling performance of anode-free lithium-metal batteries. Pressure increases the cycling efficiency at both the anode and cathode by promoting improved morphologies, while the LiAsF 6 additive additionally improves performance at the anode by enhancing the solid electrolyte interphase (SEI) properties. The combination of uniform applied pressure and a LiAsF 6 electrolyte additive produces lithium-metal batteries with cycling performance higher than can be achieved with either approach alone. This additional performance improvement is able to be realized due to the complementary rather than competitive nature of the mechanisms underlying applied pressure (lithium morphology) and electrolyte additives (SEI properties). Our results highlight the importance of moving beyond the investigation of isolated design strategies and demonstrate that superior cycling can be achieved by combining multiple approaches.

25 ENERGY STORAGE↗