Program Budgeting - Applying Economic Analysis to Government Expenditure Decisions
Program budgeting - applying economic analysis to government expenditure decisions
ECONOMICS↗
SEARCH · Engineering Papers
Results for “analysis programs”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
BASIC Programming In Water And Wastewater Analysis
Collection of computer programs assembled for use in water-analysis laboratories. First program calculates quality-control parameters used in routine water analysis. Second calculates line of best fit for standard concentrations and absorbances entered. Third calculates specific conductance from conductivity measurement and temperature at which measurement taken. Fourth calculates any one of four types of residue measured in water. Fifth, sixth, and seventh calculate results of titrations commonly performed on water samples. Eighth converts measurements, to actual dissolved-oxygen concentration using oxygen-saturation values for fresh and salt water. Ninth and tenth perform calculations of two other common titrimetric analyses. Eleventh calculates oil and grease residue from water sample. Last two use spectro-photometric measurements of absorbance at different wavelengths and residue measurements. Programs included in collection written for Hewlett-Packard 2647F in H-P BASIC.
Dreschel, Thomas↗
Computer programs for antenna feed system design and analysis
Fourteen computer programs have been developed for antenna feed system design and analysis. The programs cover a large spectrum of feed design problems, from primary feed pattern synthesis to the farfield pattern of the main reflector, including analyses of structural distortions.
Ludwig, A.↗
A digital computer program for control system analysis
Lovell digital computer program written in Fortran for calculation of control systems
Lovell, B. W.↗
A VLBI variance-covariance analysis interactive computer program
An interactive computer program (in FORTRAN) for the variance covariance analysis of VLBI experiments is presented for use in experiment planning, simulation studies and optimal design problems. The interactive mode is especially suited to these types of analyses providing ease of operation as well as savings in time and cost. The geodetic parameters include baseline vector parameters and variations in polar motion and Earth rotation. A discussion of the theroy on which the program is based provides an overview of the VLBI process emphasizing the areas of interest to geodesy. Special emphasis is placed on the problem of determining correlations between simultaneous observations from a network of stations. A model suitable for covariance analyses is presented. Suggestions towards developing optimal observation schedules are included.
Bock, Y.↗
High speed cylindrical roller bearing analysis. SKF computer program CYBEAN. Volume 2: User's manual
CYBEAN (CYlindrical BEaring ANalysis) was created to detail radially loaded, aligned and misaligned cylindrical roller bearing performance under a variety of operating conditions. Emphasis was placed on detailing the effects of high speed, preload and system thermal coupling. Roller tilt, skew, radial, circumferential and axial displacement as well as flange contact were considered. Variable housing and flexible out-of-round outer ring geometries, and both steady state and time transient temperature calculations were enabled. The complete range of elastohydrodynamic contact considerations, employing full and partial film conditions were treated in the computation of raceway and flange contacts. The practical and correct implementation of CYBEAN is discussed. The capability to execute the program at four different levels of complexity was included. In addition, the program was updated to properly direct roller-to-raceway contact load vectors automatically in those cases where roller or ring profiles have small radii of curvature. Input and output architectures containing guidelines for use and two sample executions are detailed.
Dyba, G. J.↗
Constellation Program Life-cycle Cost Analysis Model (LCAM)
The Constellation Program (CxP) is NASA's effort to replace the Space Shuttle, return humans to the moon, and prepare for a human mission to Mars. The major elements of the Constellation Lunar sortie design reference mission architecture are shown. Unlike the Apollo Program of the 1960's, affordability is a major concern of United States policy makers and NASA management. To measure Constellation affordability, a total ownership cost life-cycle parametric cost estimating capability is required. This capability is being developed by the Constellation Systems Engineering and Integration (SE&I) Directorate, and is called the Lifecycle Cost Analysis Model (LCAM). The requirements for LCAM are based on the need to have a parametric estimating capability in order to do top-level program analysis, evaluate design alternatives, and explore options for future systems. By estimating the total cost of ownership within the context of the planned Constellation budget, LCAM can provide Program and NASA management with the cost data necessary to identify the most affordable alternatives. LCAM is also a key component of the Integrated Program Model (IPM), an SE&I developed capability that combines parametric sizing tools with cost, schedule, and risk models to perform program analysis. LCAM is used in the generation of cost estimates for system level trades and analyses. It draws upon the legacy of previous architecture level cost models, such as the Exploration Systems Mission Directorate (ESMD) Architecture Cost Model (ARCOM) developed for Simulation Based Acquisition (SBA), and ATLAS. LCAM is used to support requirements and design trade studies by calculating changes in cost relative to a baseline option cost. Estimated costs are generally low fidelity to accommodate available input data and available cost estimating relationships (CERs). LCAM is capable of interfacing with the Integrated Program Model to provide the cost estimating capability for that suite of tools.
Prince, Andy↗
Computer program performs frequency analysis of nonuniform turbine disk subjected to temperature gradients
Computer program determines the natural frequencies of a turbine disk of variable thickness subjected to uniform rotation and radial temperature gradients by using Rayleigh-Ritzs procedure. The program involves the potential and kinetic energy expressions for a circular flat plate of variable thickness.
Soo, P. P.↗
A description of the computer program STIFEIG for structural dynamic analysis
FORTRAN computer program for stiffness matrix eigenvalue calculation
Hou, S. N.↗
A computer program to automate residual gas analysis
A computer program for automatic determination of gases found in an environmental chamber during spacecraft testing is discussed. Program testing is reviewed. The program is being used for the solution of experimental spectra, where the mass spectrometer is used as a contamination monitor by an untrained spectroscopist.
Shapiro, H.↗
Application of GRASP (General Rotorcraft Aeromechanical Stability Program) to nonlinear analysis of a cantilever beam
The General Rotorcraft Aeromechanical Stability Program (GRASP) was developed to analyse the steady-state and linearized dynamic behavior of rotorcraft in hovering and axial flight conditions. Because of the nature of problems GRASP was created to solve, the geometrically nonlinear behavior of beams is one area in which the program must perform well in order to be of any value. Numerical results obtained from GRASP are compared to both static and dynamic experimental data obtained for a cantilever beam undergoing large displacements and rotations caused by deformations. The correlation is excellent in all cases.
Hinnant, Howard E.↗
Simplified computer program for the analysis of phase change in liquid face seals
A simplified computer program is presented which allows for the prediction of boiling (phase change) in liquid face seals. The program determines if and when boiling occurs and then calculates the location of the boiling interface, pressure and temperature profiles, and load. The main assumption which allows for a simplified analysis is the assumption of an isothermal gas phase.
Birchak, M.↗
COMMAND: A FORTRAN program for simplified composite analysis and design
A FORTRAN program is presented for preliminary analysis and design of multilayered composite panels subjected to inplane loads. All plys are of the same material. The composite is assumed symmetric about the midplane, but need not be balanced. Failure criterion includes limit ply strains and lower bounds on composite inplane stiffnesses. Multiple load conditions are considered. The required input data is defined and examples are provided to aid the use in making the program operational. Average panel design times are two seconds on an IBM 360/67 computer. Results are compared with published literature. A complete FORTRAN listing of program COMAND is provided. In addition, the optimization program CONMIN is required for design.
Vanderplaats, G. N.↗
Analysis of data from NASA B-57B gust gradient program
Statistical analysis of the turbulence measured in flight 6 of the NASA B-57B over Denver, Colorado, from July 7 to July 23, 1982 included the calculations of average turbulence parameters, integral length scales, probability density functions, single point autocorrelation coefficients, two point autocorrelation coefficients, normalized autospectra, normalized two point autospectra, and two point cross sectra for gust velocities. The single point autocorrelation coefficients were compared with the theoretical model developed by von Karman. Theoretical analyses were developed which address the effects spanwise gust distributions, using two point spatial turbulence correlations.
Frost, W.↗
Analysis and computer program for evaluation of rotating incompressibly lubricated pressurized thrust bearings
Computer analysis of pressurized thrust bearing design using incompressible lubricant
Fleming, D. P.↗
High speed cylindrical roller bearing analysis, SKF computer program CYBEAN. Volume 2: User's manual
The CYBEAN (Cylindrical Bearing Analysis) was created to detail radially loaded, aligned and misaligned cylindrical roller bearing performance under a variety of operating conditions. Emphasis was placed on detailing the effects of high speed, preload and system thermal coupling. Roller tilt, skew, radial, circumferential and axial displacement as well as flange contact were considered. Variable housing and flexible out-of-round outer ring geometries, and both steady state and time transient temperature calculations were enabled. The complete range of elastohydrodynamic contact considerations, employing full and partial film conditions were treated in the computation of raceway and flange contacts. Input and output architectures containing guidelines for use and a sample execution are detailed.
Kleckner, R. J.↗
BUCLAP2: A computer program for instability analysis of laminated long plates subjected to combined inplane loads. User's manual
The usage of the computer program BUCLAP2 is described. The program is intended for linear instability analysis of long, rectangular flat and curved laminated plates with arbitrary orientation of orthotropic axes in each layer. The loadings considered are combinations of inplane normal and shear loads. Arbitray elastic boundary conditions are included for the sides of the plate Instructions for use of the program are included along with Input data requirements, output information, and sample problems. For program description, see .
Halstead, D. W.↗
WAATS: A computer program for Weights Analysis of Advanced Transportation Systems
A historical weight estimating technique for advanced transportation systems is presented. The classical approach to weight estimation is discussed and sufficient data is presented to estimate weights for a large spectrum of flight vehicles including horizontal and vertical takeoff aircraft, boosters and reentry vehicles. A computer program, WAATS (Weights Analysis for Advanced Transportation Systems) embracing the techniques discussed has been written and user instructions are presented. The program was developed for use in the ODIN (Optimal Design Integration System) system.
Glatt, C. R.↗