Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “active layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Identification of Acoustic Wave Signatures in the Ionosphere From Conventional Surface Explosions Using MF/HF Doppler Sounding

Here, we present an experiment to detect one ton TNT-equivalent chemical explosions using pulsed Doppler radar observations of isodensity layers in the ionospheric E region during two campaigns. The first campaign, conducted on 15 October 2019, produced potential detections of all three shots. The detections closely resemble the temporal and spectral properties predicted using the InfraGA ray tracing and weakly nonlinear waveform propagation model. Here the model predicts that within 6.5–7.25 min of each shot a waveform peaking between 0.9 and 0.4 Hz will impact the ionosphere at 100 km. As the waves pass through this region, they will imprint their signal on an isodensity layer, which is detectable using a Doppler radar operating at the plasma frequency of the isodensity. Within the time windows of each of the three shots in the first campaign, we detect enhanced wave activity peaking near 0.5 Hz. These waves were imprinted on the Doppler signal probing an isodensity layer at 2.785 MHz near 100 km altitude. Despite these detections, the method appears to be unreliable as none of the six shots from the second campaign, conducted on 10 July 2020 were detected. The observations from this campaign were characterized by an increased acoustic noise environment in the microbarom band and persistent scintillation on the radar returns. These effects obscured any detectable signal from these shots and the baseline noise was well above the detection levels of the first campaign.

47 OTHER INSTRUMENTATION↗

Mapping Firn Saturation over Greenland using NASA’s Soil Moisture Active Passive Satellite

Mapping the spatial extent of recently identified englacial hydrological features (i.e., ice slabs and perennial firn aquifers) formed by meters-thick water-saturated firn layers over the percolation facies of the Greenland Ice Sheet using L-band microwave radiometry has recently been demonstrated. However, these initial maps are binary, and do not provide a parameter to estimate the spatial variability in the thickness and volumetric fraction of meltwater stored within the firn pore space. Here, we exploit enhanced-resolution vertical-polarization L-band brightness temperature (T^(B)_(V)) imagery (2015–2019) generated using observations collected over Greenland by NASA’s Soil Moisture Active Passive (SMAP) satellite and a simple two-layer L-band brightness temperature model. We map water-saturated firn layers via a “firn saturation” parameter, and interpret our results together with ice slab and perennial firn aquifer spatial extents, estimates of snow accumulation simulated via the Regional Atmospheric Climate Model (RACMOp2.3), and airborne radar surveys collected via NASA’s Operation IceBridge (OIB) campaigns. We find that variable firn saturation parameter values are mapped in lower snow accumulation ice slab areas in western, northern, and northeastern Greenland, where firn is colder and water-saturated firn layers seasonally refreeze as solid-ice. Higher firn saturation parameter values are mapped in higher snow accumulation perennial firn aquifer areas in southeastern, southern, and northwestern Greenland, where firn is near the melting point, and meters-thick water-saturated firn layers exist. Our results have implications for identifying expansive englacial reservoirs that store significant volumes of meltwater in locations that are vulnerable to meltwater-induced hydrofracturing and accelerated outlet glacier flow year-round.

Greenland ice sheet↗

On Assessing ERA5 and MERRA2 Representations of Cold-Air Outbreaks Across the Gulf Stream

The warm Gulf Stream sea surface temperatures (SSTs) strongly impact the evolution of winter clouds behind atmospheric cold fronts. Such cloud evolution remains challenging to model. Here, the Gulf Stream is too wide within the ERA5 and MERRA2 reanalyses, affecting the turbulent surface fluxes. Known problems within the ERA5 boundary layer (too-dry and too-cool with too strong westerlies), ascertained primarily from ACTIVATE 2020 campaign aircraft dropsondes and secondarily from older buoy measurements, reinforce surface flux biases. In contrast, MERRA2 winter surface winds and air-sea temperature/humidity differences are slightly too weak, producing surface fluxes that are too low. Reanalyses boundary layer heights in the strongly-forced winter cold-air-outbreak regime are realistic, whereas late-summer quiescent stable boundary layers are too shallow. Nevertheless, the reanalysis biases are small, and reanalyses adequately support their use for initializing higher-resolution cloud process modeling studies of cold-air outbreaks.

54 ENVIRONMENTAL SCIENCES↗

Development and Characterization of Electrodes for Surface-Specific Attenuated Total Reflection Two-Dimensional Infrared Spectroelectrochemistry

Electrochemical interfaces still have remaining mysteries surrounding the interfacial region of the electrical double layer, despite being prevalent throughout the energy and water remediation industries. The electrical double layer is where many important dynamic processes such as catalysis and electron transfer occur. The goal of this work is to study the electrical double layer with two-dimensional infrared (2D IR) spectroscopy to experimentally access the details of the structural dynamics of this complex environment. However, there are several experimental challenges to applying 2D IR spectroscopy to this application, such as assuring the surface specificity of the spectrum, optimizing the signal strength while minimizing spectral distortions from dispersion and Fano line shapes, and selecting electrode materials that are both sufficiently IR compatible and conductive. Here we will discuss various considerations when designing 2D IR experiments of electrode interfaces utilizing several substrates and experimental configurations and demonstrate a robust method for 2D IR experiments of electrode interfaces under applied potential that combines nonconducting Si ATR wafers with conductive ITO and thin nanostructured films of plasmonically active Au functionalized with 3-mercapto-2-butanone (MCB). We show that layered electrodes on thin Si ATR wafers with MCB are sensitive to applied potential and that the distortions in the linear and 2D IR spectra are heavily dependent on the morphology of the Au surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

4D-STEM Coupled with Unsupervised Machine Learning to Reveal at Large-Scale the Microstructural Evolution in Li- and Mn-Rich Cathodes

Li- and Mn-rich (LMR) layered oxides are known to exhibit a thin surface reconstruction layer, which grows during electrochemical cycling in a manner that depends on exposed crystallographic facets, cycling conditions, and electrolyte chemistry. Direct characterization of this layer has traditionally relied on high-resolution electron microscopy, which is inherently limited to small fields of view. Here, we employ four-dimensional scanning transmission electron microscopy (4D-STEM) combined with unsupervised machine-learning clustering to quantitatively map phase distributions over large areas and track their evolution in LMR cathodes during electrochemical aging. Our results show that the surface reconstruction layer consists predominantly of a rocksalt phase, whose thickness varies across different facets following activation cycling and becomes substantially thicker and more uniform during calendar aging. In contrast, a spinel-like phase is observed within the particle bulk. Large-area phase mapping and correlative high-resolution imaging reveal that this spinel-like phase preferentially nucleates at bulk crystallographic defects, including boundaries between 60°-rotated layered domains and associated mixed-phase regions, rather than exclusively at the particle surface. Our findings establish a mechanistic distinction between surface-driven rocksalt formation and bulk-defect-mediated spinel nucleation while demonstrating the unique capability of 4D-STEM to provide statistically robust, mesoscale insight into complex phase-evolution processes in LMR cathodes.

4D-STEM↗

Tin sensitization and silver activation on indium tin oxide surfaces

Adhesion of electrical contacts on electronic and optoelectronic devices is important for reliable device operation. Sn-sensitization is a widely used process that improves uniformity and adhesion of plated metals to glass and polymer surfaces. Electrically conductive substrates can significantly benefit from improved uniformity, adhesion, and contact resistance to metallic contact layers. In this study, we investigate the process of Sn-sensitization and Ag-activation on indium tin oxide (ITO) surfaces—a dominant transparent conducting oxide used in optoelectronic devices. Here, our results show that ITO films exposed to Sn-sensitization solutions with HCl concentrations below 10 mM effectively modify the surface termination through the process of Sn-sensitization (Sn-bonding at the surface hydroxide sites) without etching the ITO film. However, the subsequent Ag-activation on an ITO surface does not seem to follow the typical response on a glass substrate, suggesting that Ag-activation of an ITO surface is likely limited by the Ag ion size relative to the area density of surface hydroxide sensitization sites.

42 ENGINEERING↗

Controlling Magnetization Vector Depth Profiles of La 0.7 Sr 0.3 CoO 3 /La 0.7 Sr 0.3 MnO 3 Exchange Spring Bilayers via Interface Reconstruction

The La 0.7 Sr 0.3 CoO 3–δ /La 0.7 Sr 0.3 MnO 3–δ (LSCO/LSMO) bilayer system is an ideal perovskite oxide platform for investigating interface reconstruction and its effect on their magnetic properties. Previous studies have shown that LSCO can separate into magnetic sublayers, which possess distinct trends as the total LSCO thickness increases. Here, we used polarized neutron reflectometry to quantify changes in the magnetic and chemical depth profiles, and it confirms the formation of ~12 Å-thick interfacial LSCO and LSMO layers, characterized by a decreased nuclear scattering length density compared to the bulk of the layers. This decrease is attributed to the combined effects of oxygen vacancy formation and interfacial charge transfer, which lead to magnetically active Co 2+ ions with ionic radii larger than the Co 3+ /Co 4+ ions typically found in bulk LSCO or single-layer films. The interfacial magnetization values, as well as Co 2+ ion and oxygen vacancy concentrations, depend strongly on the LSCO layer thickness. These results highlight the sensitive interplay of the cation valence states, oxygen vacancy concentration, and magnetization at interfaces in perovskite oxide multilayers, demonstrating the potential to tune their functional properties via careful design of their structure.

36 MATERIALS SCIENCE↗

Ultrafast THz emission spectroscopy of spin currents in the metamagnet FeRh

Heterostructures of ferromagnetic (FM) and noble metal (NM) thin films have recently attracted considerable interest as viable platforms for the ultrafast generation, control, and transduction of light-induced spin currents. In such systems, an ultrafast laser can generate a transient spin current in the FM layer, which is then converted to a charge current at the FM/NM interface due to strong spin–orbit coupling in the NM layer. Whether such conversion can happen in a single material and how the resulting spin current can be quantified are open questions under active study. Here, we report ultrafast THz emission from spin–charge conversion in a bare FeRh thin film without any NM layer. Our results highlight that the magnetic material by itself can enable spin–charge conversion in the same order as that in a FM/NM heterostructure. We further propose a simple model to estimate the light-induced spin current in FeRh across its metamagnetic phase transition temperature. Our findings have implications for the study of the ultrafast dynamics of magnetic order in quantum materials using THz emission spectroscopy.

36 MATERIALS SCIENCE↗

Airborne High Spectral Resolution Lidar-2 Measurements of Enhanced Depolarization in Marine Aerosols

Airborne NASA Langley Research Center (LaRC) High Spectral Resolution Lidar-2 (HSRL-2) measurements acquired during the recent NASA EVS-3 Aerosol Cloud Meteorology Interactions over the Western Atlantic Experiment (ACTIVATE) revealed enhanced particulate linear depolarization associated with aerosols within the marine boundary layer. These HSRL-2 observations were acquired off the east coast of the United States in February and March 2020 when this lidar was deployed on the NASA LaRC UC-12 aircraft. HSRL-2 measured profiles of aerosol backscattering, extinction,and depolarization at 355 and 532nm and aerosol backscattering and depolarization at 1064nm. Typically HSRL-2 measures low (<5%) linear particulate depolarization associated with marine sea salt aerosols. However, during several ACTIVATE flights, particularly those that occurred with outbreaks of cold, dry air, linear particulate depolarization exceeded 15-20% (532nm) for aerosols within a few hundred meters above the surface. These high values indicated that these particles were nonspherical. Elevated depolarization values were also observed at 355 and 1064 nm. HSRL-2 measured aerosol extinction/backscatter ratio (“lidar ratio”) values around 20-25 sr (355 and 532 nm) that are typically associated with sea salt particles. Coincident measurements of relative humidity from dropsondes released from the UC-12and in situ Diode Laser Hygrometer (DLH) measurements flown on the NASA HU-25 aircraft showed that highest depolarization values of these nonspherical particles were found when the relative humidity (RH)was below 50-60%.These lidar observations of elevated depolarization associated with sea salt aerosol are consistent with previous lidar measurements of sea salt aerosols in dry conditions. We discuss these HSRL-2 measurements also in the context of coincident airborne in situ measurements of particle size and composition acquired on the HU-25 aircraft. We also found that CALIOP satellite measurements observed elevated depolarization during some similar cold air outbreaks. In such cases, the operational CALIOP algorithms attributed the elevated depolarization to nonspherical dust particles rather than the more likely scenario of nonspherical sea salt particles associated with low RH.

aerosols↗

Achieving High‐Performance and 2000 h Stability in Anion Exchange Membrane Fuel Cells by Manipulating Ionomer Properties and Electrode Optimization

The primary function of the ionomers that are incorporated into fuel cell electrode catalyst layers is to provide pathways for ion transport between the catalyst active sites and the electrolyte. This is influenced by many variables, including the ion-exchange capacity, water uptake, and molecular weight. In anion exchange membrane fuel cells (AEMFCs), controlling ionomer water uptake is particularly important and tailoring this property in each electrode is an important consideration when looking to maximize cell performance. In this study, three poly(norbornene) tetrablock copolymer ionomers with a range of physical properties are synthesized and incorporated into AEMFC anode and cathode electrodes. Systematic electrode engineering with these ionomers allows the peak power density to be increased by 100% (1.6 W cm -2 → 3.2 W cm -2 ) and the current density at 0.2 V to be increased by 59% (5.9 A cm -2 → 9.4 A cm -2 ). Moreover, the top-performing electrode configuration is tested in an operating AEMFC at the US Department of Energy defined current density of 600 mA cm -2 for 2000 h, showing a record-low voltage decay rate of 15.36 µV h -1 – only 3.65% –a over 2000 h. Here, this work sets a new bar for AEMFCs, reporting the best combination of performance and durability of any AEMFC to date.

08 HYDROGEN↗

Discharge Rate‐Driven Li 2 O 2 Growth Exhibits Unconventional Morphology Trends in Solid‐State Li‐O 2 Batteries

Solid-state lithium oxygen batteries (LOBs) are known for their enhanced safety, higher electrochemical stability, and improved energy density compared to liquid-state LOBs. However, the investigation of solid-state LOBs is limited with little understanding of their discharge and charge processes. In this work, a polymer-based solid-state LOB is used to investigate the effect of discharge rate on lithium peroxide (Li 2 O 2 ) formation, the oxygen evolution reaction (OER), and cycle performance. Notably, we observe a counterintuitive trend: Li 2 O 2 particle size increases with increasing discharge current density, in contrast to liquid systems. This behavior arises from inherent space charge layers that restrict Li⁺ transport under high current, and spatially heterogeneous active sites at the solid electrolyte–cathode interface, directly evidenced by small angle X-ray scattering (SAXS), which govern nucleation accessibility and promote site-selective Li 2 O 2 growth. Furthermore, higher current densities improve ORR and OER efficiency but accelerate anode degradation, while lower currents promote side reactions. These opposing effects result in a trade-off that defines an optimal discharge rate (0.1 mA cm -2 ) for maximizing cycle life. This study provides a new mechanistic perspective on discharge-driven processes in solid-state LOBs and offers practical guidelines for performance optimization in future high-energy battery systems.

Discharge current density↗

Combustion of 10–100 μm aluminum droplets in detonation products gases

Here we describe a two-phase model of combustion effects in aluminized high explosive (HE) charges. It is based on: (i) a Gas Dynamic Model of the expansion of the detonation product gases and their turbulent combustion with air; and (ii) a Heterogeneous Continuum Model of aluminum (Al) droplets and their combustion with the detonation product gases. Initial conditions are based on an analytical similarity solution for a cylindrical Chapman-Jouguet (CJ) detonation propagating at the CJ detonation velocity. The CJ jump conditions are computed at the thermodynamic equilibrium state by the Cheetah code, assuming the Al droplets are inert. We assume that the Al is 10 % of the charge mass and occurs as droplets at the CJ state. Different initial droplet diameters, ranging from 10 to 100 microns, are studied. A hydrodynamic combustion model based on large Damköhler numbers is employed in this study, -3σ(1 + 0.276 $\sqrt{Re}$)/($Kd^2_w$). It has a square-root dependence on the Reynolds number (Re) and inversed-squared dependence on the droplet diameter (d w ). The burnout time (t B ) of the Al droplets has a three-halves dependence on the droplet diameter, t B ~ ($d^0_w$) 3/2 . After burnout, the detonation products act as detonation products of the HE charge with active Al. They turbulently mix with air and form a combustion layer on the outer edge of the fireball. Details of the two-phase model, initial conditions and evolution of the flow field will be described.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Superlattice-Structured Films by Magnetron Sputtering as New Era Electrodes for Advanced Lithium-ion Batteries

Sustaining sound structures in Si-based anodes is extremely challenging because of the high volumetric expansion that occurs upon cycling. To maintain high capacities over cycles, new designs rely on engineering-specific hierarchical geometries and/or optimized composite compositions such that at least one of the multiple elements serves as buffer and/or electron conductive pathways in the electrodes. In this paper, we report an innovative design in which alternating layers of periodic atomic structures involving multiple elements form a new anode material for lithium-ion batteries. In this work, a superlattice-structured amorphous film made using Si, Mo, and Cu is fabricated by a simple and scalable magnetron sputtering process for the first time. This continuous and repetitive superlattice formation along the film thickness provides a homogeneous stress-strain distribution. The Mo-Cu layer in the superlattice acts as an inactive-conductive layer and as a backbone to handle the volume expansion of active Si upon cycling. This nano-functional superlattice approach enables harnessing the high energy density of Si while maintaining its structural stability. As a result, the electrode exhibits high specific capacity and capacity retention even at high cycling rates. The possible use of the film in a full cell is also evaluated by cycling it vs. the LiMn 1.5 Ni 0.5 O 4 cathode. The full cell maintains a stable capacity of about 900 mAh g anode -1 over 150 cycles, at ~600 mA g -1 rate. The remarkable performance of this nano-functional superlattice film is found to be promising as anodes for applications that require high energy, long calendar life, and excellent abuse tolerance such as electric vehicle batteries.

25 ENERGY STORAGE↗

Iodine Immobilization by Materials through Sorption and Redox-Driven Processes: A Literature Review

Radioiodine-129 (129I) in the subsurface is mobile and limited information is available on treatment technologies. Scientific literature was reviewed to compile information on materials that could potentially be used to immobilize 129I through sorption and redox-driven processes, with an emphasis on ex-situ processes. Candidate materials to immobilize 129I include iron minerals, sulfur-based materials, silver-based materials, bismuth-based materials, ion exchange resins, activated carbon, modified clays, and tailored materials (metal organic frameworks (MOFS), layered double hydroxides (LDHs) and aerogels). Where available, compiled information includes material performance in terms of (i) capacity for 129I uptake; (ii) long-term performance (i.e., solubility of a precipitated phase); (iii) technology maturity; (iv) cost; (v) available quantity; (vi) environmental impact; (vii) ability to emplace the technology for in situ use at the field-scale; and (viii) ex situ treatment (for media extracted from the subsurface or secondary waste streams). Because it can be difficult to compare materials due to differences in experimental conditions applied in the literature, Part II of this review describes results of laboratory studies for selected materials using a standardized batch loading test.

Moore, Robert C.↗

Diamonds in the Rough: Direct Surface Enhanced Infrared Spectroscopic Evidence of Nitrogen Reduction on Boron-Doped Diamond Supported Metal Catalysts

In situ investigations of electrocatalytic processes of increasing societal interest such as the nitrogen reduction reaction (NRR) re-quire aggressive experimental conditions that are not readily compatible with surface sensitive techniques such as attenuated total reflection surface enhanced infrared absorption spectroscopy (ATR-SEIRAS). A method for performing ATR-SEIRAS studies at very negative potentials where conventional IR-active films delaminate, and fail is reported. The method relies on a thin film of very robust boron-doped diamond deposited on a micromachined Si wafer, which provides extended mid-IR transparency at long wavelengths. SEIRAS activity is achieved by electrodepositing gold nanoparticles onto the conductive BDD layer. The Au@BDD layers are shown to sustain prolonged periods of electrolysis at negative potentials with no degradation of the modifying layer. The efficacy of these substrates for electrocatalysis is demonstrated by studying the reduction of N 2 at -1.5 V vs Ag/AgCl in an aqueous-based electrolyte. So under these conditions, direct spectroscopic evidence of both NH 3 and hydrazine formed from the nitrogen reduction reaction (NRR) is provided.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydraulic fracture characterization by integrating multidisciplinary data from the Hydraulic Fracturing Test Site 2 (HFTS-2)

Various technologies have traditionally been used to monitor and describe hydraulic fractures from different perspectives. This work demonstrates the value of data integration for hydraulic fracture characterization when multiple data resources are available. The Hydraulic Fracturing Test Site 2 (HFTS 2) is a hydraulic fracturing research project in the Delaware Basin with multiple surveillance techniques including fiber optics sensing, microseismic, pressure/temperature gauges, etc. We integrated the multidisciplinary data from the HFTS-2 to characterize hydraulic fractures. The integrated data revealed interesting fracture propagation features including layering, vertical propagation affected by pore pressure gradient, and different microseismic activities due to difference in-situ conditions. Furthermore, these findings can be insightful for understanding hydraulic fracture propagation. The comparison among multiple surveillance data also helps us to evaluate the roles of various surveillance technologies and provides us experience to make informative decisions depending on different monitoring objectives.

58 GEOSCIENCES↗

High Energy Benthic Boundary Layer Experiment (HEBBLE): Preliminary program plan and conceptual design

Deep sea processes of flow-sediment interaction, particularly the role of high energy ocean bottom current events in forming the seafloor topography, transporting material, and mixing the bottom of the water column are examined. A series of observations at and near the sea bottom, in water depths of 4 to 5 km, in areas of the western North Atlantic where high energy current events occur, include site surveys and physical reconnaissance to identify suitable areas and positions, and one or more six month experiments to investigate temporal and spatial variations of high energy events within the boundary layer and their interaction with the seabed. Descriptions of proposed HEBBLE activities are included, with emphasis on technology transfer to the oceanographic community through design, fabrication, testing, and operation of an instrumented ocean bottom lander.

Frewing, K.↗

Color changes at the Viking landing sites over the course of a Mars year

Color changes at the Viking landing sites over the past Mars year are examined. Both sites exhibited an increased red to blue ratio of the soil due to the accumulation of a thin layer of bright red dust from the two global dust storms. The generation of bright areas on Mars and the formation of dark areas by stripping of bright dust layers are explained by the lander observations before the dust storm activity which show isolated bright red drifts which may be regions where material deposited during previous storms was protected from wind erosion.

Guinness, E. A.↗