Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transitional flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Aerodynamic performance of a supersonic throughflow fan stage

The NASA LeRC has begun a program to design, analyze, build, and test a fan stage that can operate with supersonic axial velocities throughout the stage. This report presents the results from the initial experimental evaluation of the supersonic throughflow fan stage. The stage was tested with flows at subsonic and supersonic inlet axial Mach numbers and with rotor speeds at 40 to 100 percent of design speed. Overall performance as well as detailed performance obtained from radially and circumferentially traversing probes downstream of the stator vanes is presented. At the design rotor tip speed of 1500 ft/s and the design Mach number of 2.0, the measured overall pressure ratio was 2.22, and the corresponding adiabatic efficiency was 0.694. Transition from subsonic to supersonic flow was successfully demonstrated at 75, 90, and 100 percent of design speed. In that speed range, the stage 'unstart' (transition from supersonic to subsonic inlet axial conditions) occurred at an inlet axial Mach number of about 1.36, which corresponds to the Mach number at which the stage started.

Royce D Moore↗
NASA NTRS1973

An adverse effect of film cooling on the suction surface of a turbine vane

A J-75 size turbine vane with film cooling holes on the suction surface near the leading edge was tested with and without film cooling flow in a four vane cascade. Results show that the cooling effectiveness on the aft portion of the vane suction surface can decrease with the addition of film cooling near the leading edge. Apparently the film cooling air flow caused a laminar or transitional boundary layer to become a transitional or turbulent boundary layer. The vane was tested at a gas temperature and pressure of 1260 K (1800 F) and 22.7 newtons per square centimeter (33 psia), a coolant temperature of 280 K (50 F), film cooling flow ratios from 0.0 to 0.026, and backside midchord cooling flow ratios of 0.007 and 0.035.

Gladden, H. J.↗
NASA NTRS1991

Navier-Stokes analysis of turbomachinery blade external heat transfer

The two-dimensional, compressible, thin-layer Navier-Stokes and energy equations were solved numerically to obtain heat transfer rates on turbomachinery blades. The Baldwin-Lomax algebraic model and the q-omega low Reynolds number two-equation model were used for modeling of turbulence. For the numerical solution of the governing equations a four-stage Runge-Kutta solver was employed. The turbulence model equations were solved using an implicit scheme. Numerical solutions are presented for two-dimensional flow within two vane cascades. The heat transfer results and the pressure distributions were compared with published experimental data. The agreement between the numerical calculations and the experimental values were found to be generally favorable. The position of transition from laminar to turbulent flow was also predicted accurately.

Gorla, Rama S. R.↗
NASA NTRS1992

Navier-Stokes analysis of turbomachinery blade external heat transfer

The two-dimensional, compressible, thin-layer Navier-Stokes and energy equations were solved numerically to obtain heat transfer rates on turbomachinery blades. The Baldwin-Lomax algebraic model and the q - omega low Reynolds number, two-equation model were used for modeling of turbulence. For the numerical solution of the governing equations a four-stage Runge-Kutta solver was employed. The turbulence model equations were solved using an implicit scheme. Numerical solutions are presented for two-dimensional flow within two vane cascades. The heat transfer results and the pressure distributions were compared with published experimental data. The agreement between the numerical calculations and the experimental values were found to be generally favorable. The position of transition from laminar to turbulent flow was also predicted accurately.

Ameri, A. A.↗
NASA NTRS1994

A multi-ion generalized transport model of the polar wind

The higher-order generalizations of the equations of standard hydrodynamics, known collectively as generalized transport theories, have been used since the early 1980s to describe the terrestrial polar wind. Inherent in the structure of generalized transport theories is the ability to describe not only interparticle collisions but also certain non-Maxwellian processes, such as heat flow and viscous stress, that are characteristic of any plasma flow that is not collision dominated. Because the polar wind exhibits a transition from collision-dominated to collisionless flow, generalized transport theories possess advantages for polar wind modeling not shared by either collision-dominated models (such as standard hydrodynamics) or collisionless models (such as those based on solving the collisionless Boltzmann equation). In general, previous polar wind models have used generalized transport equations to describe electrons and only one species of ion (H(+)). If other ion species were included in the models at all, it was in a simplified or semiempirical manner. The model described in this paper is the first polar wind model that uses a generalized transport theory (bi-Maxwellian-based 16-moment theory) to describe all of the species, both major and minor, in the polar wind plasma. In the model, electrons and three ion species (H(+), He(+), O(+)) are assumed to be major and several ion species are assumed to be minor (NO(+), Fe(+), O(++)). For all species, a complete 16-moment transport formulation is used, so that profiles of density, drift velocity, parallel and perpendicular temperatures, and the field-aligned parallel and perpendicular energy flows are obtained. In the results presented here, emphasis is placed on describing those constituents of the polar wind that have received little attention in past studies. In particular, characteristic solutions are presented for supersonic H(+) outflow and for both supersonic and subsonic outflows of the major ion He(+). Solutions are also presented for various minor ions, both atomic and molecular and both singly and multiply charged.

Demars, H. G.↗
DOE OSTI2026

A finite viscoelastic constitutive model for low to high strain rate response of elastomers with application of strain rate-induced glass transition

Amorphous elastomers exhibit significant rate-stiffening and unique viscous flow characteristics across a wide range of strain rates, often undergoing glass transition above a strain rate threshold. We have developed a thermodynamically-consistent and micromechanically-inspired constitutive model for soft elastomeric materials to capture the rate-dependent stress-strain behavior and hysteresis when subjected to low to high strain rates. Here, our proposed constitutive model encapsulates the viscous flow of materials through molecular motion at low strain rates and local rearrangement and alignment of the molecules trying to overcome the intermolecular resistance at high strain rates, essentially covering the glass transition. We applied our constitutive model to uniaxial compression experiments performed at low and high strain rates for polyborosiloxane (PBS) to identify the material parameters, and subsequently, performed numerical simulations of single and multi-cycle compression, stress relaxation, and small amplitude oscillatory tension-compression. Our analyses indicate that the model predicts higher total energy dissipation with increasing strain rate; however, dissipation associated with molecular relaxation decreases (forming a cusp) because, beyond a crossover strain rate, intermolecular rearrangement and alignment become dominant, which is consistent with the onset of the glass transition. For cyclic loading-unloading, we observed that dissipation over a cycle remains constant at low strain rates but decreases non-monotonically at high strain rates before becoming constant, with the peak stress over the cycle becoming higher, which can be interpreted as more loading being carried elastically by the polymer network as the intermolecular rearrangement process occurs. Additionally, our model was able to predict the qualitative nature of the storage modulus and loss modulus in the limit of small strain over a wide range of frequency sweeps.

36 MATERIALS SCIENCE↗
NASA NTRS1938

Determination of Boundary-Layer Transition on Three Symmetrical Airfoils in the NACA Full-Scale Wind Tunnel

For the purpose of studying the transition from laminar to turbulent flow, boundary-layer measurements were made in the NACA full-scale wind tunnel on three symmetrical airfoils of NACA 0009, 0012, and 0018 sections. The effects of variations in lift coefficient, Reynolds number, and airfoil thickness on transition were investigated. Air speed in the boundary layer was measured by total-head tubes and by hot wires; a comparison of transition as indicated by the two techniques was obtained. The results indicate no unique value of Reynolds number for the transition, whether the Reynolds number is based upon the distance along the chord or upon the thickness of the boundary layer at the transition point. In general, the transition is not abrupt and occurs in a region that varies in length as a function of the test conditions.

Silverstein, Abe↗
NASA NTRS1993

The effects of shrinkage flow and gravity level on the onset of convection during vertical directional dendritic solidification of NH4Cl-H2O

A numerical investigation of the conditions influencing the onset of convection during Bridgman vertical directional solidification of NH4Cl- 72 wt percent H2O has been made using a linear stability model. The effects of shrinkage flow and gravity level on the transition from diffusion-dominated to convection-dominated solidification are shown to be significant. Both shrinkage flow opposite the direction of growth and increased gravity levels tend to decrease the stability limits defining the onset of convection for the solidifying NH4Cl-H2O system.

Hopkins, J. A.↗
NASA NTRS1982

Surface flow visualization using indicators

Surface flow visualization using indicators in the cryogenic wind tunnel which requires a fresh look at materials and procedures to accommodate the new test conditions is described. Potential liquid and gaseous indicators are identified. The particular materials illustrate the various requirements an indicator must fulfill. The indicator must respond properly to the flow phenomenon of interest and must be observable. Boundary layer transition is the most important phenomenon for which flow visualization indicators may be employed. The visibility of a particular indicator depends on utilizing various optical or chemical reactions. Gaseous indicators are more difficult to utilize, but because of their diversity may present unusual and useful opportunities. Factors to be considered in selecting an indicator include handling safety, toxicity, potential for contamination of the tunnel, and cost.

Crowder, J. P.↗
NASA NTRS1985

MPD thruster performance - Propellant distribution and species effects

Previous research has shown that MPD thruster performance, as measured by thrust, specific impulse, and efficiency, is limited by a so-called 'onset' current level. Experimental results are presented which show that the onset current level varies with the radial position of mass injection. Specifically, mass injection into either of two zones results in drastically different performance for both argon and xenon propellants. This difference in performance is evidenced by the onset current levels, the onset V-J signatures, and the overall V-J characteristics. The behavior of the thruster with the total mass flow split between the two zones follows a transition between the zonal behavioral limits. The behavior of propellant mixtures also follows a transition between the behavior of the individual propellant species. The flow region between the two zones is characterized by a particle number density discontinuity, a large axial current density, and a large electron Hall parameter, suggesting a possible correlation between observed onset phenomena and a shear-flow discontinuity located in the region between the two zones.

Kelly, A. J.↗
NASA NTRS2010

Analysis of a Transonic Alternating Flow Phenomenon Observed During Ares Crew Launch Vehicle Wind Tunnel Tests

A transonic wind tunnel test of the Ares I-X Rigid Buffet Model (RBM) identified a Mach number regime where unusually large buffet loads are present. A subsequent investigation identified the cause of these loads to be an alternating flow phenomenon at the Crew Module-Service Module junction. The conical design of the Ares I-X Crew Module and the cylindrical design of the Service Module exposes the vehicle to unsteady pressure loads due to the sudden transition from separated to attached flow about the cone-cylinder junction with increasing Mach number. For locally transonic conditions at this junction, the flow randomly fluctuates back and forth between a subsonic separated flow and a supersonic attached flow. These fluctuations produce a square-wave like pattern in the pressure time histories which, upon integration result in large amplitude, impulsive buffet loads. Subsequent testing of the Ares I RBM found much lower buffet loads since the evolved Ares I design includes an ogive fairing that covers the Crew Module-Service Module junction, thereby making the vehicle less susceptible to the onset of alternating flow. An analysis of the alternating flow separation and attachment phenomenon indicates that the phenomenon is most severe at low angles of attack and exacerbated by the presence of vehicle protuberances. A launch vehicle may experience either a single or, at most, a few impulsive loads since it is constantly accelerating during ascent rather than dwelling at constant flow conditions in a wind tunnel. A comparison of a wind-tunnel-test-data-derived impulsive load to flight-test-data-derived load indicates a significant over-prediction in the magnitude and duration of the buffet load

Sekula, Martin K.↗
DOE OSTI2022

Header for high-pressure heat exchanger

A header for a high-pressure heat exchanger includes a first high-pressure transition section with inlets for multiple first high-pressure flow channels that are spaced from one another in a radial direction and collectively arranged in a substantially circular shape. The inlets for the multiple first high-pressure flow channels on a radially outer edge of the first high-pressure transition section are spaced further apart in a circumferential direction from adjacent inlets of the multiple first high-pressure flow channels than radially inward inlets are spaced from adjacent radially inward inlets of the multiple first high-pressure flow channels. The header also includes multiple first high-pressure flow channels extending from the first high-pressure transition section to a second-high pressure transition section that is configured to divide each of the multiple first high-pressure flow channels into at least two first high-pressure sub-flow channels. Each flow channel of the multiple first high-pressure flow channels and each sub-flow channel of the first high-pressure sub-flow channels have a round cross-sectional shape.

Kirsch, Kathryn L.↗
NASA NTRS1994

Comparison of full-scale, small-scale, and CFD results for F/A-18 forebody slot blowing

It has been shown experimentally that forebody flow control devices provide a significant increase in yaw control for fighter aircraft at high angle-of-attack. This study presents comparisons of the various experimental and computational results for tangential slot blowing on the F/A-18 configuration. Experimental results are from the full-scale and 6 percent-scale model test and computational solutions are from both isolated forebody and and full aircraft configurations. The emphasis is on identifying trends in the variation of yawing moment with blowing-slot exit conditions. None of the traditional parameters (mass flow ratio, blowing momentum coefficient, velocity ratio) succeeded in collapsing all of the results into a common curve. Several factors may effect the agreement between the 6 percent- and full-scale results including Reynolds number effects, sensitivity of boundary layer transition from laminar to turbulent flow, and poor geometric fidelity, particularly of the blowing slot. The disagreement between the full-scale and computed yawing moments may be due to a mismatch in the slot exit conditions for the same mass flow ratio or aircraft configuration modeling. The general behavior of slot blowing on the 6 percent-scale and computational models is correct, but neither matches the full-scale results.

Lanser, Wendy R.↗
NASA NTRS2013

Proposed Flight Research of a Dual-Bell Rocket Nozzle Using the NASA F-15 Airplane

For more than a half-century, several types of altitude-compensating rocket nozzles have been proposed and analyzed, but very few have been adequately tested in a relevant flight environment. One type of altitude-compensating nozzle is the dual-bell rocket nozzle, which was first introduced into literature in 1949. Despite the performance advantages that have been predicted, both analytically and through static test data, the dual-bell nozzle has still not been adequately tested in a relevant flight environment. This paper proposes a method for conducting testing and research with a dual-bell rocket nozzle in a flight environment. We propose to leverage the existing NASA F-15 airplane and Propulsion Flight Test Fixture as the flight testbed, with the dual-bell nozzle operating during captive-carried flights, and with the nozzle subjected to a local flow field similar to that of a launch vehicle. The primary objective of this effort is not only to advance the technology readiness level of the dual-bell nozzle, but also to gain a greater understanding of the nozzle mode transitional sensitivity to local flow-field effects, and to quantify the performance benefits with this technology. The predicted performance benefits are significant, and may result in reducing the cost of delivering payloads to low-Earth orbit.

Jones, Daniel S.↗
NASA NTRS2013

Proposed Flight Research of a Dual-Bell Rocket Nozzle Using the NASA F-15 Airplane

For more than a half-century, several types of altitude-compensating rocket nozzles have been proposed and analyzed, but very few have been adequately tested in a relevant flight environment. One type of altitude-compensating nozzle is the dual-bell rocket nozzle, which was first introduced into literature in 1949. Despite the performance advantages that have been predicted, both analytically and through static test data, the dual-bell nozzle has still not been adequately tested in a relevant flight environment. This paper proposes a method for conducting testing and research with a dual-bell rocket nozzle in a flight environment. We propose to leverage the existing NASA F-15 airplane and Propulsion Flight Test Fixture as the flight testbed, with the dual-bell nozzle operating during captive-carried flights, and with the nozzle subjected to a local flow field similar to that of a launch vehicle. The primary objective of this effort is not only to advance the technology readiness level of the dual-bell nozzle, but also to gain a greater understanding of the nozzle mode transitional sensitivity to local flow-field effects, and to quantify the performance benefits with this technology. The predicted performance benefits are significant, and may result in reducing the cost of delivering payloads to low-Earth orbit.

Jones, Daniel S.↗
NASA NTRS2013

Proposed Flight Research of a Dual-Bell Rocket Nozzle Using the NASA F-15 Airplane

For more than a half-century, several types of altitude-compensating rocket nozzles have been proposed and analyzed, but very few have been adequately tested in a relevant flight environment. One type of altitude-compensating nozzle is the dual-bell rocket nozzle, which was first introduced into literature in 1949. Despite the performance advantages that have been predicted, both analytically and through static test data, the dual-bell nozzle has still not been adequately tested in a relevant flight environment. This presentation proposes a method for conducting testing and research with a dual-bell rocket nozzle in a flight environment. We propose to leverage the existing NASA F-15 airplane and Propulsion Flight Test Fixture as the flight testbed, with the dual-bell nozzle operating during captive-carried flights, and with the nozzle subjected to a local flow field similar to that of a launch vehicle. The primary objective of this effort is not only to advance the technology readiness level of the dual-bell nozzle, but also to gain a greater understanding of the nozzle mode transitional sensitivity to local flow-field effects, and to quantify the performance benefits with this technology. The predicted performance benefits are significant, and may result in reducing the cost of delivering payloads to low-Earth orbit.

rocket↗
NASA NTRS1980

Mount assembly for porous transition panel at annular combustor outlet

A gas turbine engine combustor assembly of annular configuration has outer and inner walls made up of a plurality of axially extending multi-layered porous metal panels joined together at butt joints therebetween and each outer and inner wall including a transition panel of porous metal defining a combustor assembly outlet supported by a combustor mount assembly including a stiffener ring having a side undercut thereon fit over a transition panel end face; and wherein an annular weld joins the ring to the end face to transmit exhaust heat from the end face to the stiffener ring for dissipation from the combustor; a combustor pilot member is located in axially spaced, surrounding relationship to the end face and connector means support the stiffener ring in free floating relationship with the pilot member to compensate for both radial and axial thermal expansion of the transition panel; and said connector means includes a radial gap for maintaining a controlled flow of coolant from outside of the transition panel into cooling relationship with the stiffener ring and said weld to further cool the end face against excessive heat build-up therein during flow of hot gas exhaust through said outlet.

Sweeney, Ralph B.↗