Results for “ThIn” — Page 75

NASA NTRS2018

Influence of Thin-Film Adhesives in Pullout Tests Between Nickel-Titanium Shape Memory Alloy and Carbon Fiber-Reinforced Polymer Matrix Composites

Strips of nickel-titanium (NiTi) shape memory alloy (SMA) and carbon fiber-reinforced polymer matrix composite (PMC) were bonded together using multiple thin film adhesives and their mechanical strengths were evaluated under pullout test configuration. Tensile and lap shear tests were conducted to confirm the deformation of SMAs at room temperature and to evaluate the adhesive strength between the NiTi strips and the PMC. Optical and scanning electron microscopy techniques were used to examine the interfacial bonding after failure. Simple equations on composite tensile elongation were used to fit the experimental data on tensile properties. ABAQUS models were generated to show the effects of enhanced bond strength and the distribution of stress in SMA and PMC. The results revealed that the addition of thin film adhesives increased the average adhesive strength between SMA and PMC while halting the room temperature shape memory effect within the pullout specimen.

Polymer Matrix Composites↗

NASA NTRS2016

Shrink Tape Technique for Heat Forming Aluminum Substrates for Thin Foil X-Ray Mirrors and the Neutron Star Interior Composition Explorer X-Ray Concentrators

Consistent improvements in the design and fabrication of thin-foil, epoxy-replicated x-ray mirrors for astronomical telescopes have yielded increasingly higher quality and more precise astrophysical data. The Neutron Star Interior Composition Explorer (NICER) x-ray timing mission optics continues this tradition and introduces design elements that promise even more accurate measurements and precise astrophysical parameters. The singly reflecting concentrators have a curved axial profile to improve photon concentration and a sturdy full shell structure for enhanced module stability. These design elements introduced the challenge of reliably forming mirror substrates at an acceptable production rate. By developing a technique using heat shrink tape to compress and conform thin aluminum mirror substrates to shaping mandrels, production rate improved with successful fabrication. The technique's efficiency was analyzed by measuring hundreds of substrate profiles postforming, performance testing completely assembled concentrators composed of every size substrate, and comparing the results to simulated fabrication scenarios. On average, the profiles were copied within 4.6 plus or minus 3.7 percent. These measurements and the overall success of NICER's optics, via ground calibration, have shown that the heat-shrink tape method is reliable, repeatable, and could be used in future missions to increase production rate and improve performance.

Balsamo, Erin↗

NASA NTRS2018

A Simple Test Method for Large Deformation Bending of Thin High Strain Composite Flexures

A simple test method for large deformation bending of thin composite laminates is investigated using image processing and full-field strain measurements. The assumptions and kinematic equations that represent the test are used to calculate numerically the laminate bending stiffness and strength as well as the curvature and strains at failure. In order to validate the test methodology, a comparison is performed between analytical model predictions and empirical data in terms of computed surface strains versus digital image correlation data and calculated rotation angles of the fixture arms throughout the test versus measured ones. The new test method is then used to calculate the bending stiffness in the D11 and D22 directions as well as failure strains for various thin-ply laminates of interest. These parameters are ultimately compared with predicted values using micromechanics and classical lamination theory analysis. In general, bending stiffness and strain test results and predictions for 0 degree orientation coupons have a maximum difference of 10% and 35%.

Fernandez, Juan M.↗

NASA NTRS2018

A Screening Method Using Pulsed-Power Combined with Infrared Imaging to Detect Pattern Defects in Bulk Metal Foil or Thin Film Resistors

Bulk metal foil and thin film resistors occasionally contain localized defects within the etched resistor pattern. Common defects of this type include in-line constrictions referred to as notches, unremoved resistor material bridges between adjacent pattern lines, and embedded non-conductive particles in the resistor material. Such defects are prone to fracture due to thermomechanical fatigue during powered operation, especially power cycling, resulting in positive resistance change and open circuit failure modes. Common screening methods of optical microscopy, short time overload power tests (e.g., 6.25x rated power for 5 seconds) and burn-in (e.g., 1.5x rated power for 100 hours) are useful, but they are not always effective at removing devices with such defects. An improved method has been developed to screen for localized resistor pattern defects. The method involves the application of brief, high power electrical pulses at a low duty cycle while inspecting the resistor with a high resolution, high speed infrared camera. The following test conditions were found to be suitable for this purpose: 6.25x rated power, 1 to 5 pulses, 50 ms pulse width and 10% duty cycle. During the power pulsing, localized constrictions in the resistor pattern are identifiable as hot spots via the infrared camera. Reject criteria can be established based on observations of hot spots. To assess its effectiveness, a total of two hundred eighty (280) surface mount foil resistors (40 each from 7 different lots) were screened using this infrared technique. The screening identified twenty-nine (29) resistors with significant hot spots in the resistor pattern. All 280 resistors were then subjected to an industry standard 10,000 hour life test at 1x rated power at 70°C with power cycled for 90 minutes on and 30 minutes off. During life testing, three resistors exhibited positive resistance change failure mode. All three failures were due to thermomechanical fatigue failure of localized bridge defects at the locations identified via infrared screening. The results of this evaluation illustrate the benefits of the pulsed-power infrared detection screening technique to identify reliability suspect foil or thin film resistors that may escape common screening methods.

screening↗

NASA NTRS2016

Retrieval of Daily Maps of PM2.5 Aerosol in the Problematic California Valleys: Bright, Speckled Reflectances, Thin AOT, but High Pollution

The San Joaquin Valley suffers from severe episodes of respirable aerosol (PM2.5) in wintertime.We provide maps of aerosol episodes using daily snapshots of PM2.5 and its changing features despite numerous difficulties inherent to sampling the region. Linear relationships relating aerosol optical thickness (AOT) to PM2.5 give an explained variance of approximately 3.The GEO-CAPE mission has as a goal the provision of relevant measures of respirable aerosol to the community,but has not formulated a science goal beyond the limited goal of retrieval of AOT, bringing the usefulness of GEO-CAPE into doubt.Our special focus was on the DISCOVER-AQ period, Jan-Feb 2013, which had many supporting measurements.Both high pollution and retrieval difficulties tend to occur in many Mediterranean agricultural regions like the San Joauin. One difficulty is the relatively bright surfaces with considerable exposed soil. NASAs MAIAC and MODIS Deep Blue retrieval techniques are shown to have considerable skill even at low aerosol optical thickness (AOT) values, as evaluated by concurrent AERONET sunphotometer measurements.More significantly, these AOT values can correspond to high daytime PM2.5 since aerosol mixed layer depth is thin and variable, 200m 600 m. The thin layers derive from typical subsidence of dry air between more stormy periods. This situation provides an advantage: water vapor column is also almost completely limited to a similar mixed layer depth, and can thus serve as a measure of aerosol dilution.Using the MAIAC Water Vapor Column:In order to make the maps below, we used the MAIAC data but subtracted partial water-vapor columns estimated from MERRA Reanalysis Data availabe from the GSFC GMAO using kriging. We did not use the mixed-layer estimates from MERRA, since such analyses were found problematic during our forecasting exercises for DISCOVER-AQ. Observations from the aircraft soundings suggested that this overlying moisture was mostly due to larger scale flows, not ML venting.However, the specific humidity at the surface and a nearly well-mixed ML was analyzed by kriging from the surface network (MesoWest, University of Utah). These were thought to be truer, uninfluenced by physical process modeling that combines with data observations. (TBD: How different are they?) Procedure: Subtract overlying partial water columns from MAIAC column water and divide this by a surface value of water vapor. (MAIAC column is expressed in cm of water, i.e., water vapor at surface conditions.This method appears to bring out useful details in the distribution of submicron particles in the very problematic Wintertime San Joaquin Valley, and allow analysis of pollution episodes throughout the valley, rather than long-term averages.

san joaquin valley↗

NASA NTRS2018

A Screening Method Using Pulsed-Power Combined with Infrared Imaging to Detect Pattern Defects in Bulk Metal Foil or Thin Film Resistors

Bulk metal foil and thin film resistors occasionally contain localized defects within the etched resistor pattern. Common defects of this type include in-line constrictions referred to as notches, unremoved resistor material bridges between adjacent pattern lines, and embedded non-conductive particles in the resistor material. Such defects are prone to fracture due to thermomechanical fatigue during powered operation, especially power cycling, resulting in positive resistance change and open circuit failure modes. Common screening methods of optical microscopy, short time overload power tests (e.g., 6.25x rated power for 5 seconds) and burn-in (e.g., 1.5x rated power for 100 hours) are useful, but they are not always effective at removing devices with such defects. An improved method has been developed to screen for localized resistor pattern defects. The method involves the application of brief, high power electrical pulses at a low duty cycle while inspecting the resistor with a high resolution, high speed infrared camera. The following test conditions were found to be suitable for this purpose: 6.25x rated power, 1 to 5 pulses, 50 ms pulse width and 10% duty cycle. During the power pulsing, localized constrictions in the resistor pattern are identifiable as hot spots via the infrared camera. Reject criteria can be established based on observations of hot spots. To assess its effectiveness, a total of two hundred eighty (280) surface mount foil resistors (40 each from 7 different lots) were screened using this infrared technique. The screening identified twenty-nine (29) resistors with significant hot spots in the resistor pattern. All 280 resistors were then subjected to an industry standard 10,000 hour life test at 1x rated power at 70°C with power cycled for 90 minutes on and 30 minutes off. During life testing, three resistors exhibited positive resistance change failure mode. All three failures were due to thermomechanical fatigue failure of localized bridge defects at the locations identified via infrared screening. The results of this evaluation illustrate the benefits of the pulsed-power infrared detection screening technique to identify reliability suspect foil or thin film resistors that may escape common screening methods.

screening↗

NASA NTRS2019

The Intermediate Wake of a Thin Flat Plate with a Circular Trailing Edge

The intermediate wakes of thin flat plates with circular trailing edges (TEs) are investigated here with direct numerical simulations (DNSs). The separating boundary layers are turbulent in all cases. The near wake in two thin-plate cases (IN & NS), with a focus on the vortex shedding process, was explored in a recent article. Intermittent shedding was observed in Case IN. Case NS, with half the TE diameter of Case IN, was an essentially non-shedding case. A third case (ST) with a sharp trailing edge was also investigated and found to exhibit an intermittent wake instability. The objectives of the present study are twofold. The first is to determine if the wake instability found in Case ST exists in Cases IN and NS as well. The second is to provide the distributions of the turbulent normal intensities and shear stress in the wake and to understand these distributions via the budget terms in the corresponding transport equations. The results show that both Cases IN & NS exhibit a wake instability in the intermediate wake region, that is similar to that found earlier in Case ST. We note that in Case IN, the presence of an intermediate-wake instability results in the co-existence of two different types of instability within a single wake. The distributions of the turbulent normal intensities and shear stress, and the budget terms for the streamwise intensity are included and discussed here. All the budget terms contribute appreciably to the overall budget in the transport equation for streamwise normal intensity.

Rai, Man Mohan↗

NASA NTRS2020

The Variable and Non-Variable X-Ray Absorbers in Compton-Thin Type II Active Galactic Nuclei

We have conducted an extensive X-ray spectral variability study of a sample of 20 Compton-thin type II galaxies using broadband spectra from XMM-Newton, Chandra, and Suzaku. The aim is to study the variability of the neutral intrinsic X-ray obscuration along the line of sight and investigate the properties and location of the dominant component of the X-ray-obscuring gas. The observations are sensitive to absorption columns of N(sub H) ∼ 10(exp 20.5–24) cm(exp -2) of fully and partially covering neutral and/or lowly ionized gas on timescales spanning days to well over a decade. We detected variability in the column density of the full-covering absorber in 7/20 sources, on timescales of months to years, indicating a component of compact-scale X-ray-obscuring gas lying along the line of sight of each of these objects. Our results imply that torus models incorporating clouds or over-dense regions should account for line-of-sight column densities as low as ∼a few ×10(exp 21) cm(exp -2). However, 13/20 sources yielded no detection of significant variability in the full-covering obscurer, with upper limits of ΔN(sub H) spanning 10(exp 21–23) cm(exp -2). The dominant absorbing media in these systems could be distant, such as kiloparsec-scale dusty structures associated with the host galaxy, or a homogeneous medium along the line of sight. Thus, we find that overall, strong variability in full-covering obscurers is not highly prevalent in Compton-thin type IIs, at least for our sample, in contrast to previous results in the literature. Finally, 11/20 sources required a partial-covering, obscuring component in all or some of their observations, consistent with clumpy near-Compton-thick compact-scale gas.

Active galaxies↗

NASA NTRS2019

Disentangling Planets from Photoelectric Instability in Gas-rich Optically Thin Dusty Disks

Structures in circumstellar disks such as gaps and rings are often attributed to planets. This connection has been difficult to show unequivocally, as other processes may also produce these features. In particular, a photoelectric instability (PEI) has been proposed, operating in gas-rich optically thin disks, that generates structures predicted by planet–disk interactions. We examine the question of how to disentangle the planetary effects on disk structure from the effects of the PEI. We use the Pencil Code to perform 2D global hydrodynamical models of the dynamics of gas and dust in a thin disk with and without planetary perturbers. Photoelectric heating is modeled with an equation of state where pressure is proportional to dust surface density. The drag force on grains and its backreaction on the gas are included. Analyzing the situation without PEI, we find that gas–dust interactions alter the shape of the planetary gap from the dust-free case when the local dust-to-gas ratio ε approaches unity. This result also applies to primordial disks, because dust drifting inward accumulates at the edge of the planetary gap, and any initial dust-to-gas ratio eventually achieves ε = 1 if the dust reservoir is sufficient. We find a result particular to high dust-to-gas ratio disks as well: as dust drifts inward, the dust front becomes a sharp transition, and the backreaction triggers the Rossby wave instability. When PEI is included, we find that it obscures structures induced by planets unless the planet's mass is sufficiently large to carve a noticeable gap. Specifically, the instability generates arcs and rings of regular spacing: a planet is discernible when it carves a dust gap wider than the wavelength of the PEI.

Areli Castrejon↗

NASA NTRS2020

Sensitivities in Satellite Lidar‐Derived Estimates of Daytime Top‐of‐the‐Atmosphere Optically Thin Cirrus Cloud Radiative Forcing: A Case Study

An optically thin cirrus cloud was profiled concurrently with nadir‐pointing 1,064 nm lidars on 11 August 2017 over eastern Texas, including NASA's airborne Cloud Physics Lidar (CPL) and space‐borne Clouds and Aerosol Transport System (CATS) instruments. Despite resolving fewer (37% vs. 94%) and denser (i.e., more emissive) clouds (average cloud optical depth of 0.10 vs. 0.03, respectively), CATS data render a near‐equal estimate of the top‐of‐atmosphere (TOA) net cloud radiative forcing (CRF) versus CPL. The sample‐relative TOA net CRF solved from CPL is 1.39 W/m2, which becomes 1.32 W/m2 after normalizing by occurrence frequency. Since CATS overestimates extinction for this case, the sample‐relative TOA net forcing is ~3.0 W/m2 larger than CPL, with the absolute value reduced to within 0.3 W/m2 of CPL due its underestimation of cloud occurrence. We discuss the ramifications of thin cirrus cloud detectability from satellite and its impact on attempts at TOA CRF closure.

Erica K. Dolinar↗

NASA NTRSDate not supplied

Determining the Cause of Reduced Concurrent Flame Spread over Thin Solid Fuels in Low Pressure and Low Gravity

The spread of flames over the surface of solid combustible materials is affected by the environmental conditions. Variables such as flow velocity, oxygen concentration, ambient pressure, partial gravity or microgravity, may change the material flammability and influence the fire dynamics. This is an important fire safety issue for space exploration vehicles and space habitats which will very likely have different environments than those currently used on the International Space Station, such as reduced pressure and enriched oxygen concentration (SEA). However, testing experimentally the materials to be used and qualified for space exploration under these conditions is a difficult and expensive task. Here, numerical modeling is used to understand the dominant physico-chemical processes on the concurrent flame spread over thin fabrics under reduced ambient pressure (and in turn, buoyancy) and variable gravitational conditions. The numerical model uses the Fire Dynamics Simulator (FDS6) code with a single-step Arrhenius reaction rate for the solid phase decomposition. Different models are tested for the gas phase combustion kinetics. The model results are validated with experimental results obtained at similar reduced ambient pressure and flow conditions at 1 g. It is shown that as ambient pressure is reduced the flame spread rate over a thin fabric is also reduced, both experimentally and numerically. Numerical results are compared to an analytical approach previously developed to explain the experimental trends. Further interpretation of the model results provides information regarding the physics of the process and how they are affected by the lower pressure environments and gravity conditions. The results of this work provide guidance for potential on-earth testing for fire safety design in spacecraft and space habitats.

Fire Safety↗

NASA NTRSDate not supplied

Determining the Cause of Reduced Concurrent Flame Spread over Thin Solid Fuels in Low Pressure and Low Gravity

The spread of flames over the surface of solid combustible materials is affected by the environmental conditions. Variables such as flow velocity, oxygen concentration, ambient pressure, partial gravity or microgravity, may change the material flammability and influence the fire dynamics. This is an important fire safety issue for space exploration vehicles and space habitats which will very likely have different environments than those currently used on the International Space Station, such as reduced pressure and enriched oxygen concentration (SEA). However, testing experimentally the materials to be used and qualified for space exploration under these conditions is a difficult and expensive task. Here, numerical modeling is used to understand the dominant physico-chemical processes on the concurrent flame spread over thin fabrics under reduced ambient pressure (and in turn, buoyancy) and variable gravitational conditions. The numerical model uses the Fire Dynamics Simulator (FDS6) code with a single-step Arrhenius reaction rate for the solid phase decomposition. Different models are tested for the gas phase combustion kinetics. The model results are validated with experimental results obtained at similar reduced ambient pressure and flow conditions at 1 g. It is shown that as ambient pressure is reduced the flame spread rate over a thin fabric is also reduced, both experimentally and numerically. Numerical results are compared to an analytical approach previously developed to explain the experimental trends. Further interpretation of the model results provides information regarding the physics of the process and how they are affected by the lower pressure environments and gravity conditions. The results of this work provide guidance for potential on-earth testing for fire safety design in spacecraft and space habitats.

microgravity↗

NASA NTRS2022

Impact of Assimilating Adaptively Thinned AIRS Cloud-Cleared Radiances on the Analysis of Polar Lows and Mediterranean Sea Tropical-Like Cyclone in a Global Modeling and Data Assimilation Framework

Polar lows, and mesoscale convective cyclones bearing resemblance to tropical cyclones but originating outside of the tropics, are storms that are challenging to represent accurately in global analyses and models because of their small size, rapid growth at subsynoptic scales, occurrence in data poor oceanic regions, and difficulties in objectively validating them in analysis. Building on previous positive results obtained with respect to the representation of tropical cyclones (TCs) in a global model, a set of observing system experiments (OSEs) performed using the NASA Goddard Earth Observing System (GEOS, version 5) are investigated, focusing on three case studies—a polar low in the Sea of Okhotsk, a polar low in the Southern Ocean, and a Mediterranean Sea tropical-like cyclone that occurred during the boreal fall season of 2014. Experiments assimilating adaptively thinned cloud-cleared hyperspectral infrared radiances from the Atmospheric Infrared Sounder (AIRS) instrument on board the NASA Aqua satellite, with higher density in the vicinity of each storm and its pre-cyclogenesis environment, and lower density elsewhere, demonstrate a positive impact on the analyzed representation of each storm. The adaptive thinning experiments improve the storm intensity and structure, including vertical alignment, depth, symmetry, strength, and compactness of warm core compared to the reference experiments. The results suggest that jet-level processes associated with extremely strong horizontal velocity gradients as represented in the model analysis can be useful to locate dynamically active regions of the extratropical atmosphere where denser data coverage is likely to improve the analyzed representation of polar lows and other similar marine mesoscale convective cyclones.

global modeling↗

NASA NTRS2022

Determining Flame Temperature By Broadband Two Color Pyrometry in A Flame Spreading Over A Thin Solid in Microgravity

Fire spread inside a spacecraft is a constant concern in space travel. Understanding how the fire grows and spreads, and how it can potentially be extinguished is critical for planning future missions. The conditions inside a spacecraft can greatly vary from those encountered on earth, including microgravity, low velocity flows, reduced ambient pressure and high oxygen, and thus affecting the combustion processes. In microgravity, the contributions of thermal radiation from gaseous species and soot can play a critical role in the spread of a flame and the problem has not been fully understood yet. The overall objective of this work is to address this by studying the soot temperature of microgravity flames spreading over a thin solid in microgravity. The experiments presented here were performed as part of the NASA project Saffire IV, conducted in orbit on board the Cygnus resupply vehicle before it re-entered the Earth’s atmosphere. The fuel considered is a thin fabric made of cotton and fiberglass (Sibal) exposed to a forced flow of 20 cm/s in a concurrent flow configuration. Reconstruction of the flame temperature fields is extracted from two color broadband emission pyrometry (B2CP) as the flame propagates over the solid fuel. A methodology, relevant assumptions and its applicability to other microgravity experiments are discussed here. The data obtained shows that the technique provides an acceptable average temperature around ~1300 K, which remains relatively constant during the spread with an error value smaller than 117 K. The data presented in this work provides a methodology that could be applied to other microgravity experiments to be performed by NASA. It is expected that the results will provide insight for what is to be expected in different conditions relevant for fire safety in future space facilities.

fire↗

NASA NTRS2019

Using Gaia Data 2 to Constrain Local Dark Matter Density and Thin Dark Disk

We use stellar kinematics from the latest Gaia data release (DR2) to measure the local dark matter (DM) density ρDM in a heliocentric cylinder of radius R = 150 pc and half-height z = 200 pc. We also explore the prospect of using our analysis to estimate the DM density in local substructure by setting constraints on the surface density and scale height of a thin dark disk aligned with the baryonic disk and formed due to dissipative dark matter self-interactions. Performing the statistical analysis within a Bayesian framework for three types of tracers, we obtain ρDM = 0.016 ± 0.010 Mꙩ/p c 3 for A stars; early G stars give a similar result, while F stars yield a significantly higher value. For a thin dark disk, A stars set the strongest constraint: excluding surface densities (5–12) Mꙩ/pc 2 for scale heights below 100 pc with 95% confidence. The upper bound of this constraint implies . 1% of the Milky Way DM mass is present in a dissipative dark sector. Comparing our results with those derived using Tycho-Gaia Astrometric Solution (TGAS) data, we find that the uncertainty in our measurements of the local DM content is dominated by systematic errors that arise from assumptions of our dynamical analysis in the low z region. Furthermore, there will only be a marginal reduction in these uncertainties with more data in the Gaia era. We comment on the robustness of our method and discuss potential improvements for future work.

dark matter theory↗

NASA NTRSDate not supplied

Results of First Long Duration Space Flight of Hybrid Perovskite Thin Film

In support of NASA's Artemis program with the goal of a sustained human-lunar presence, there is a need for very large (>100kW) and high-voltage-capable solar arrays, estimated to cost over $150M. Perovskite-based thin-film photovoltaics offer substantial advantages over state-of-the-art solar arrays from the perspective of manufacturing large arrays. Perovskites have also demonstrated some of the lowest temperature coefficients and highest defect tolerance, which make them excellent candidates for aerospace applications. However, MHPs must demonstrate durability in space which presents different challenges than terrestrial operating environments. To decisively test the viability of perovskites being used in space, a perovskite thin film is positioned in low earth orbit for 10 months on the International Space Station, which was the first long-duration study of an MHP in space. Postflight high-resolution ultrafast spectroscopic characterization and comparison with control samples reveal that the flight sample exhibits superior photo-stability, no irreversible radiation damage, and a suppressed structural phase transition temperature by nearly 65 K, broadening the photovoltaic operational range. Further, significant photo-annealing of surface defects is shown following prolonged light-soaking postflight. These results emphasize that methylammonium lead iodide can be packaged adequately for space missions, affirming that space stressors can be managed as theorized.

William Delmas↗

NASA NTRSDate not supplied

Segmented, Pleat-Folded and Rib-Supported Thin-Shell Composite Antenna Reflector

A new architecture scalable to sizes greater than 10 m for a deployable solid surface reflector antenna is presented. The design makes use of radially and circumferentially segmented thin-shell composite gores interconnected on the back side by a series of flexible shape memory composite elements. The reflector surface stows like an umbrella by creating serpentine-shaped pleats in the thin shell while being supported by a simple-hinged metering rib structure. A parametric study assessed how design features affect the deployed stiffness of the reflector and are used to identify a test matrix for manufacturing, foldability, and shape accuracy assessments. Various manufacturing tooling designs and dedicated folding fixtures were built to increase the fidelity and confidence of the test articles produced. An overview of the development effort is provided.

Deployable antennas↗

NASA NTRSDate not supplied

Segmented, Pleat-Folded and Rib-Supported Thin-Shell Composite Antenna Reflector

A new architecture scalable to sizes greater than 10 m for a deployable solid surface reflector antenna is presented. The design makes use of radially and circumferentially segmented thin-shell composite gores interconnected on the back side by a series of flexible shape memory composite elements. The reflector surface stows like an umbrella by creating serpentine-shaped pleats in the thin shell while being supported by a simple-hinged metering rib structure. A parametric study assessed how design features affect the deployed stiffness of the reflector and are used to identify a test matrix for manufacturing, foldability, and shape accuracy assessments. Various manufacturing tooling designs and dedicated folding fixtures were built to increase the fidelity and confidence of the test articles produced. An overview of the development effort is provided.

Deployable antennas↗