Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phased array”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

The Impact of Local Meteorological Conditions on Airframe Noise Flight Test Data

Phased microphone array measurements obtained during flight tests conducted in 2016 and 2017 are used to assess the importance of local meteorological measurements on the data. In particular, the effectiveness of atmospheric absorption corrections is evaluated under vastly different temperature and humidity conditions. The results indicate that, even under conditions with high absorption, sources can be visualized up to a frequency that is dependent on background noise levels, wind, and atmospheric turbulence. However, absolute levels were found to be problematic on days with high absorption rates, with the discrepancies most prevalent for aircraft positions further from the center of the array. Restricting the data to those days with favorable meteorological conditions generally resulted in a good collapse of the spectra, with differences less than a couple of decibels.

Lockard, David P.↗

Analysis of Simulated and Experimental Noise Sources of Boeing 777 Main Gear Model via CLEAN in 3D

Previously obtained experimental and simulated phased microphone array data for the NASA 26%-scale model of a six-wheel main landing gear, with and without a toboggan-shaped noise reduction fairing, were analyzed using the CLEAN technique in three dimensions. The model is a high-fidelity representation of the Boeing 777-200 aircraft main landing gear. The reprocessing of the acoustic data was undertaken to address the deficiencies encountered in the source localization (beamform) maps and the integrated farfield spectra at mid to high frequencies in our previous study, where conventional array processing techniques were applied to the same data sets. Application of the CLEAN approach resulted in higher quality beamform maps with many of the previously observed side lobes either eliminated or suppressed significantly. As a result, integration of the experimentally and computationally based maps showed substantial improvement in the quality of the high-frequency spectral content relative to the corresponding spectra generated via conventional array processing, thus extending the good agreement achieved between the measured and predicted farfield spectra from 8 kHz to 14 kHz in model-scale frequencies. In addition, an examination of the simulated surface pressure fluctuations, off-surface flow field, and three-dimensionally constructed noise sources was conducted to determine the cause of the subtle discrepancies between measured and predicted sound pressure levels that occur in the 1,800 Hz to 4,000 Hz model-scale frequency range.

Ravetta, Patricio↗

Flight-Test Evaluation of Airframe Noise Mitigation Technologies

A series of flight tests targeting airframe noise reduction was planned and executed under the NASA Flight Demonstrations and Capabilities project. The objectives of the tests were two-fold: to evaluate the aeroacoustic performance of several noise reduction technologies in a relevant environment and to generate a comprehensive database for advancing the state of the art in simulation-based airframe noise prediction methodologies. These technologies – an Adaptive Compliant Trailing Edge flap, main landing gear fairings, and gear cavity treatments – were integrated on a NASA Gulfstream G-III aircraft to determine their effectiveness, both on a component-level (individually) and a system-level (combined) basis. With the aircraft flying an approach pattern and the engines set at ground idle, extensive acoustic measurements were acquired using a phased microphone array system. Detailed analyses of the gathered acoustic data clearly demonstrate that significant noise reduction was achieved for the flap and main landing gear components.

Khorrami, Mehdi R.↗

Assessment of Airframe Noise Reduction Technologies Based on EPNL from Flight Tests

The acoustic performance of various airframe noise reduction technologies – Adaptive Compliant Trailing Edge flap, main landing gear fairings, and gear cavity treatments – was determined, individually and in combination, using the Effective Perceived Noise Level metric. These noise measurements and calculations closely follow the Federal Aviation Administration aircraft noise certification standards, specifically for the approach noise measurement point. The flyover data correspond to pole-mounted, single-microphone measurements obtained during a series of flight tests, conducted under the NASA Flight Demonstrations and Capabilities project, that evaluated flap and landing gear noise reduction technologies. To minimize contributions from the propulsion system, the aircraft was flown along the approach path with engine thrust set at ground idle. Although contamination from engine, background, and secondary airframe noise sources partially masked the true performance of the tested technologies, the resulting acoustic data clearly showed substantial noise reductions relative to baseline levels. The acoustic benefits measured by the single microphones are consistent with previously reported trends in acoustic levels obtained from phased microphone array data.

Ravetta, Patricio A.↗

Flight-Test Evaluation of Landing Gear Noise Reduction Technologies

Results from the third Acoustics Research Measurements flight test, conducted under the NASA Flight Demonstrations and Capabilities project, are presented and discussed. The test evaluated landing gear and gear cavity noise mitigation technologies installed on a NASA Gulfstream G-III. Aircraft configurations with and without main landing gear treatments were flown at several flap deflections to determine the acoustic performance of the technologies for aircraft equipped with conventional Fowler flaps. With the aircraft flying an approach path and engines at “ground-idle,” extensive acoustic measurements were acquired with a phased microphone array system. Computed beamform maps were used to examine the effectiveness of the tested technologies in reducing the strength of the noise sources generated by the main landing gear. Various integration regions were devised to extract the farfield noise spectra associated with the treated and untreated landing gear configurations. Analyses of the gathered acoustic data demonstrate that significant noise reduction was achieved. How- ever, the full noise reduction potential of the technologies could not be determined because of contamination from flap inboard edge noise and other secondary sources.

Khorrami, Mehdi R.↗

Flight-Test Evaluation of Landing Gear Noise Reduction Technologies

Results from the third Acoustics Research Measurements flight test, conducted under the NASA Flight Demonstrations and Capabilities project, are presented and discussed. The test evaluated landing gear and gear cavity noise mitigation technologies installed on a NASA Gulfstream G-III. Aircraft configurations with and without main landing gear treatments were flown at several flap deflections to determine the acoustic performance of the technolo-gies for aircraft equipped with conventional Fowler flaps. With the aircraft flying an approach path and engines at “ground-idle,” extensive acoustic measurements were acquired with a phased microphone array system. Computed beamform maps were used to examine the effec-tiveness of the tested technologies in reducing the strength of the noise sources generated by the main landing gear. Various integration regions were devised to extract the farfield noise spectra associated with the treated and untreated landing gear configurations. Analyses of the gathered acoustic data demonstrate that significant noise reduction was achieved. How-ever, the full noise reduction potential of the technologies could not be determined because of contamination from flap inboard edge noise and other secondary sources.

Mehdi R Khorrami↗

Benefits of 3D Beamforming

This presentation discusses the advantages of beamforming in 3D relative to 2D for data obtained on non-axisymmetric nozzle configurations.

Phased Array↗

Deep Space C3 : high power uplinks

The uplink transmitters of the Deep Space Network (DSN) perform three key functions in support of space missions: navigation, command uplink, and emergency recovery. The transmitters range in frequency from S-band to Ka-band, and range in RF transmit power from 200W to 400kW. Future improvements to the uplink transmitters will focus on higher frequency transmitters for high data rate communications, high power X-band uplinks for emergency recovery, and /or in-phase uplink arraying for either application

Morabito, David D.↗

Effect of Geometric Granularity on the Noise Signature of a Full-Scale Large Civil Transport Nose Landing Gear

Results from a comprehensive simulation campaign focused on characterizing the air-frame noise signature of a full-scale Boeing 777-300ER nose landing gear are presented. The as-flown, installed nose gear geometry was used to assess how accurately the selected computational methodology can predict far-field noise before extending the simulation approach to the complete B777-300ER aircraft in landing configuration. To facilitate direct comparisons with experimental data, the simulations were conducted for conditions matching those recorded for a flyby of the same aircraft over the ground-based phased microphone array used during the 2005 Quiet Technology Demonstrator II test. The far-field acoustic footprint of the nose landing gear was computed via a Ffowcs-Williams and Hawkings integral approach, with pressures on the model solid surface or flow quantities on a permeable data surface enclosing the gear used as input. A grid refinement study performed for the baseline gear con-figuration to establish the convergence behavior of the far-field spectrum indicated that the sound pressure levels had converged at frequencies slightly beyond 5 kHz for the finest spatial resolution attempted. To ascertain the effects of geometric granularity on far-field noise, simulations of a defeatured version of the nose gear were undertaken. Comparisons with fully-dressed gear results indicated that finer geometric details add 2–4 dB to the sound pressure levels at mid- to high-frequencies (800 Hz to 5 kHz), suggesting that for accurate noise prediction such details cannot be neglected.

airframe noise↗

Noise Measurements from Ground Tests of the Moog SureFly Vehicle

Noise measurements from a ground test of a small vertical lift research vehicle are presented. The proof-of-concept all-electric vehicle called “SureFly” was developed by Moog, Inc. A cooperative effort between NASA and Moog, Inc. has led to one of the first acoustic test datasets from an Urban Air Mobility (UAM) vehicle being developed for passenger and cargo. Results show propeller and possibly motor tones are important for the overall noise levels. The vehicle has four support arms each with a pair of contra-rotating propellers. Noise measurements show higher noise levels from the lower propellers, likely due to inflow distortion from the arms and top propellers. Possible motor noise was identified by calculating harmonics of the line frequency and comparing to the tones in the narrowband acoustic spectra and phased microphone array data. The acoustic far field was found to be about 100 ft away from the vehicle, but additional microphones are needed to provide a better assessment. Results show the presence of modulation for some test conditions. The work reported here is only for ground tests.

Acoustics↗

Noise Measurements from Ground Tests of the Moog SureFly Vehicle

Noise measurements from a ground test of a small vertical lift research vehicle are presented. The proof-of-concept all-electric vehicle called “SureFly” was developed by Moog, Inc. A cooperative effort between NASA and Moog, Inc. has led to one of the first acoustic test datasets from an Urban Air Mobility (UAM) vehicle being developed for passenger and cargo. Results show propeller and possibly motor tones are important for the overall noise levels. The vehicle has four support arms each with a pair of contra-rotating propellers. Noise measurements show higher noise levels from the lower propellers, likely due to inflow distortion from the arms and top propellers. Possible motor noise was identified by calculating harmonics of the line frequency and comparing to the tones in the narrowband acoustic spectra and phased microphone array data. The acoustic far field was found to be about 100 feet away from the vehicle, but additional microphones are needed to provide a better assessment. Results show the presence of modulation for some test conditions. The work reported here is only for ground tests.

Acoustics↗

Comparison of Boeing 777 Landing Gear Noise Simulations with Flight Test Data

Acoustic phased microphone array measurements of aircraft flyover noise acquired during the 2005 Quiet Technology Demonstrator II test were used to assess the accuracy of high-fidelity, full-scale simulations of landing gear noise produced by a large civilian aircraft. The simulations, conducted with the lattice Boltzmann solver PowerFLOW®, used a highly accurate digital model of a Boeing 777-300ER aircraft with the nose and main landing gear components replicating the full-scale geometries. The simulations were performed for aircraft parameters that matched those recorded during the flyover test conditions. For benchmarking purposes, several aircraft configurations were simulated: a) nose landing gear deployed with main landing gear and wing high-lift devices stowed, b) nose and main landing gear deployed with wing high-lift devices stowed and c) nose and main landing gear with wing high-lift devices deployed. To facilitate direct comparison with measured data, the simulated data sets were used to generate synthetic pressure records at the same array microphone locations as those used during the flight test. Broadly self-consistent beamforming techniques and procedures were used to process the synthetic pressure records and the measured data. Integration of select regions of the beamform maps containing the nose or main landing gear yielded good agreement between predicted and measured integrated far-field spectra for forward directivity angles where airframe noise is more prominent.

airframe noise↗

Aeroacoustic Computations of a Generic Low Boom Concept in Landing Configuration: Part 3 - Aerodynamic Validation and Noise Source Identification

Wind tunnel test data were used to validate the predicted aerodynamic behavior of a 15%-scale version of a generic, low-boom aircraft. The test was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel to determine the low-speed aerodynamic characteristics of the model. Measured steady surface pressures and global forces were used to validate predicted aerodynamic results obtained from high-fidelity simulations of the model as installed in the tunnel. Very good agreement between predicted and measured aerodynamic trends was demonstrated, providing the impetus to proceed with companion airframe noise simulations that were conducted in a free-air setting. Computed near-field flow variables acquired on a permeable data surface were used to generate synthetic pressure records for two 800-element phased microphone arrays positioned overhead and to the side of the model. The array data were beamformed to generate noise source localization maps for the clean model and several landing configurations. Primary and secondary airframe sources were identified and their relative strengths were determined. Far-field integrated noise spectra for the full aircraft, as well as individual components, were obtained from the source maps via integration of tailored regions. The analysis showed that noise produced by the landing gear was the dominant contributor to the far-field acoustic signature of the model, followed by flap noise. The effects of permeable data surface end caps, spatial resolution, array orientation, angle of attack, component interaction, velocity scaling, and numerical precision on synthetic far-field spectra were also evaluated.

low boom↗

Self-Healing RF/Microwave Communications Circuits/Systems for NASA Missions—A Review

The success of current and future NASA missions relies in great part on the performance reliability and robustness of the communication circuits and systems of said missions. Some of the manifestations of reliability and robustness are comprised by properties such as graceful degradation, which provide redundancy and potentially longer life to the mission, and the ability to perform efficiently in harsh environments destinations such as Venus and the Jovian and Saturnian moons Europa and Enceladus, respectively. While several approaches have been considered or are currently underway to develop communications circuitry capable of performing in harsh environments, they lack the flexibility to enable reconfigurability to preserve functionality under adverse or contingency scenarios. This paper discusses some examples of self-healing RF/Microwave communications circuits and systems that could provide advantageous options in support of NASA missions.

self-healing↗