Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Insulators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Spray Foam Exterior Insulation with Stand-Off Furring - New York

IBACOS and Green Homes America 1 (GHA) collaborated with the New York State Energy Research and Development Authority (NYSERDA) Advanced Buildings Program to research a variation of a commercial curtain wall assembly for residential construction as part of a comprehensive whole-house deep energy retrofit (DER) package. The advantages of this strategy include minimizing the physical connections to each individual existing wall stud, using closedcell spray foam to encapsulate existing siding materials including lead paint, and creating a vented rain screen assembly to promote drying. As Moore (2011) states, "Closed-cell foam acts as air-sealing, insulation, and secondary drainage plane..." Field installations on a limited number of houses indicate that the incremental cost when installed as part of a typical siding and window replacement job adds approximately $10/ft2 of wall area. 2 x 4 framing members were attached to the wall at band joists and top plates using "L" clips, and spray foam was used to insulate the wall after the framing was installed. Windows were installed as the framing was put up, including extension jambs. Key lessons learned include the following: (1) The installed cost of the spray foam system was comparable to the installed cost of the rigid foam and furring strips. (2) Spray foam should be applied in such a way that it locks the framing members in place before the remaining foam is installed in the field of the wall. The spray foam has a tendency to move the new wall framing as it expands. Best practice is to "picture frame" the wall framing with spray foam and then apply the spray foam in the field of each bay. (3) Variations in the existing siding conditions must be accounted for when attaching the ledger boards and wall framing. A best practice is to uniformly shim the ledger boards off the walls so the new framing is a uniform distance from the ledger boards and the inside surface of the interior framing. This is important primarily for window and door installation and the associated extension jambs and trim. (4) From a sequencing perspective, it is advantageous to replace the windows at the same time as the exterior walls are being built. This requires a crew that can perform a number of different tasks (e.g., framing, flashing, window install, trim carpentry) and does not lend itself to subcontracting this approach piecemeal (e.g., framing subcontractor, window installer, drainage plane installer, trim carpenter). (5) Application of the brackets and associated fastener screws was more time consuming than anticipated. (6) It is important for the spray foam contractor to perform all preparatory work, which in this case included placing plastic over the windows and exposed foundation to minimize or eliminate the possibility of damage due to overspray.

Array↗

Development Path for Cryogenic Insulation Systems Supporting NASA Exploration

The currently stated exploration plan for NASA includes the possibilities ranging from short (several hour duration) upper stage missions sending astronauts towards the vicinity of the moon to multiyear missions to Mars and even making and liquefying propellant on the surface of Mars. As such, NASA has developed a plan to develop multilayer insulation (MLI) at a level it can be engineered for large space craft and upper stage mission durations between several hours to several days. The Evolvable Cryogenics project has been investigating design details related to the design of large MLI blankets for in-space application. Basic MLI performance for large upper stages is scheduled to be demonstrated in 2018 on the Evolvable Cryogenics projects Structural Heat Intercept, Insulation, and Vibration Evaluation Rig (SHIIVER). Different paths are being pursued for Mars Surface applications and these concepts are much less defined and still being traded.

Insulation systems↗

Engineered Interfaces in Extruded Polyphenylsulfone-Boron Nitride Composite Insulation

Improving matrix-filler interactions is critical for optimizing dielectric performance in composite insulation; however, the technique used to introduce inorganic fillers into an organic matrix varies in its ability to satisfactorily reduce the size of cavities and interfaces. This study reports effects from changing the filler incorporation strategy on the rheology, dielectric performance and thermal conductivity of extruded polyphenylsulfone (PPSU) – hexagonal boron nitride (hBN) composite insulation. Depending on the technique used to introduce BN into the host matrix, the viscosity, torque, and melt viscosity temperature of the polymer were reduced, enabling better mixing, heat transfer, and smaller voids. This corresponded to an increase in dielectric strength compared to other formulations at either a similar or lower filler loading. On the other hand, the thermal conductivity in these specimens shifted further away from the thermal conductivity target of 1 W/m·K, which was an indication of a larger separation distance between the particles in samples with smaller interfaces. A trade-off between dielectric strength and thermal conductivity may exist when maximizing thermal conduction without sacrificing dielectric strength.

Polyphenylsulfone↗

Technology Solutions Case Study: Cladding Attachment Over Thick Exterior Insulating Sheathing

The addition of insulation to the exterior of buildings is an effective means of increasing the thermal resistance of wood-framed walls and mass masonry wall assemblies. Insulation on the exterior of the structure has many direct benefits, including better effective R-value from reduced thermal bridging, better condensation resistance, reduced thermal stress on the structure, as well as other commonly associated improvements such as increased airtightness and improved water management. Although the approach has proven effective, there is resistance to its widespread implementation due to a lack of research and understanding of the mechanisms involved in the development of the vertical displacement resistance capacity. In addition, the long-term in-service performance of the system has been questioned due to potential creep effects of the assembly under the sustained dead load of the cladding and effects of varying environmental conditions. In addition, the current International Building Code (IBC) and International Residential Code (IRC) do not have a provision that specifically allows this assembly. In this project, researchers from Building Science Corporation, a Building America team, investigated these issues to better understand the mechanics behind this method of cladding attachment

BSC↗

Measuring the Impact of Experimental Parameters upon the Estimated Thermal Conductivity of Closed-Cell Foam Insulation Subjected to an Accelerated Aging Protocol ? Two Year Results

The thermal conductivity of many closed-cell foam insulation products changes over time as production gases diffuse out of the cell matrix and atmospheric gases diffuse into the cells. Thin slicing has been shown to be an effective means of accelerating this process in such a way as to produce meaningful results. Efforts to produce a more prescriptive version of the ASTM C 1303 standard test method have led to a broad ruggedness test. This test includes the aging of full size insulation specimens for time periods up to five years for later comparison to the predicted results. Experimental parameters under investigation include: slice thickness, slice origin (at the surface or from the core of the slab), thin slice stack composition, product facings, original product thickness, product density, and product type. This paper will compare the results after two years of full-thickness aging.

42 ENGINEERING↗

Tuning Fermi Levels in Intrinsic Antiferromagnetic Topological Insulators MnBi 2 Te 4 and MnBi 4 Te 7 by Defect Engineering and Chemical Doping

MnBi 2 Te 4 and MnBi 4 Te 7 are intrinsic antiferromagnetic topological insulators, offering a promising materials platform for realizing exotic topological quantum states. However, high densities of intrinsic defects in these materials not only cause bulk metallic conductivity, preventing the measurement of quantum transport in surface states, but may also affect magnetism and topological properties. In this paper, systematic density functional theory calculations reveal specific material chemistry and growth conditions that determine the defect formation and dopant incorporation in MnBi 2 Te 4 and MnBi 4 Te 7 . The large strain induced by the internal heterostructure promotes the formation of large-size-mismatched antisite defects and substitutional dopants. The results here show that the abundance of antisite defects is responsible for the observed n-type metallic conductivity. Additionally, a Te-rich growth condition is predicted to reduce the bulk free electron density, which is confirmed by experimental synthesis and transport measurements in MnBi 2 Te 4 . Furthermore, Na doping is proposed to be an effective acceptor dopant to pin the Fermi level within the bulk band gap to enable the observation of surface quantum transport. The defect engineering and doping strategies proposed here should stimulate further studies for improving synthesis and for manipulating magnetic and topological properties in MnBi 2 Te 4 , MnBi 4 Te 7 , and related magnetic topological insulators.

36 MATERIALS SCIENCE↗

Surface-Driven Evolution of the Anomalous Hall Effect in Magnetic Topological Insulator MnBi 2 Te 4 Thin Films

We report understanding the effects of the interfacial modification to the functional properties of magnetic topological insulator thin films is crucial for developing novel technological applications from spintronics to quantum computing. Here, a large electronic and magnetic response is reported to be induced in the intrinsic magnetic topological insulator MnBi 2 Te 4 by controlling the propagation of surface oxidation. It is shown that the formation of the surface oxide layer is confined to the top 1–2 unit cells but drives large changes in the overall magnetic response. Specifically, a dramatic reversal of the sign of the anomalous Hall effect is observed to be driven by finite thickness magnetism, which indicates that the film splits into distinct magnetic layers each with a unique electronic signature. These data reveal a delicate dependence of the overall magnetic and electronic response of MnBi 2 Te 4 on the stoichiometry of the top layers. This study suggests that perturbations resulting from surface oxidation may play a non-trivial role in the stabilization of the quantum anomalous Hall effect in this system and that understanding targeted modifications to the surface may open new routes for engineering novel topological and magnetic responses in this fascinating material.

36 MATERIALS SCIENCE↗

Spectroscopic Studies on the Metal-Insulator Transition Mechanism in Correlated Materials

Here, the metal–insulator transition (MIT) in correlated materials is a novel phenomenon that accompanies a large change in resistivity, often many orders of magnitude. It is important in its own right but its switching behavior in resistivity can be useful for device applications. From the material physics point of view, the starting point of the research on the MIT should be to understand the microscopic mechanism. Here, an overview of recent efforts to unravel the microscopic mechanisms for various types of MITs in correlated materials is provided. Research has focused on transition metal oxides (TMOs), but transition metal chalcogenides have also been studied. Along the way, a new class of MIT materials is discovered, the so–called relativistic Mott insulators in 5d TMOs. Distortions in the MO 6 (M = transition metal) octahedron are found to have a large and peculiar effect on the band structure in an orbital dependent way, possibly paving a way to the orbital selective Mott transition. In the final section, the character of the materials suitable for applications is summarized, followed by a brief discussion of some of the efforts to control MITs in correlated materials, including a dynamical approach using light.

36 MATERIALS SCIENCE↗

Topological Crystalline Insulator Candidate ErAsS with Hourglass Fermion and Magnetic-Tuned Topological Phase Transition

Topological crystalline insulators (TCIs) with hourglass fermion surface state have attracted a lot of attention and are further enriched by crystalline symmetries and magnetic order. Here, the emergence of hourglass fermion surface state and exotic phases in the newly discovered, air-stable ErAsS single crystals are shown. In the paramagnetic phase, ErAsS is expected to be a TCI with hourglass fermion surface state protected by the nonsymmorphic symmetry. Dirac-cone-like bands and nearly linear dispersions in large energy range are experimentally observed, consistent well with theoretical calculations. Below T N ≈ 3.27 K, ErAsS enters a collinear antiferromagnetic state, which is a trivial insulator breaking the time-reversal symmetry. An intermediate incommensurate magnetic state appears in a narrow temperature range (3.27–3.65 K), exhibiting an abrupt change in magnetic coupling. Overall, the results reveal that ErAsS is an experimentally available TCI candidate and provide a unique platform to understand the formation of hourglass fermion surface state and explore magnetic-tuned topological phase transitions.

36 MATERIALS SCIENCE↗

Electrical Manipulation of Topological Phases in a Quantum Anomalous Hall Insulator

Quantum anomalous Hall phases arising from the inverted band topology in magnetically doped topological insulators have emerged as an important subject of research for quantization at zero magnetic fields. Though necessary for practical implementation, sophisticated electrical control of molecular beam epitaxy (MBE)-grown quantum anomalous Hall matter have been stymied by growth and fabrication challenges. Here, in this study, a novel procedure is demonstrated, employing a combination of thin-film deposition and 2D material stacking techniques, to create dual-gated devices of the MBE-grown quantum anomalous Hall insulator, Cr-doped (Bi,Sb) 2 Te 3 . In these devices, orthogonal control over the field-induced charge density and the electric displacement field is demonstrated. A thorough examination of material responses to tuning along each control axis is presented, realizing magnetic property control along the former and a novel capability to manipulate the surface exchange gap along the latter. Through electrically addressing the exchange gap, the capabilities to either strengthen the quantum anomalous Hall state or suppress it entirely and drive a topological phase transition to a trivial state are demonstrated. The experimental result is explained using first principle theoretical calculations, and establishes a practical route for in situ control of quantum anomalous Hall states and topology.

36 MATERIALS SCIENCE↗

In‐Operando Spatiotemporal Imaging of Coupled Film‐Substrate Elastodynamics During an Insulator‐to‐Metal Transition

Abstract The drive toward non‐von Neumann device architectures has led to an intense focus on insulator‐to‐metal (IMT) and the converse metal‐to‐insulator (MIT) transitions. Studies of electric field‐driven IMT in the prototypical VO 2 thin‐film channel devices are largely focused on the electrical and elastic responses of the films, but the response of the corresponding TiO 2 substrate is often overlooked, since it is nominally expected to be electrically passive and elastically rigid. Here, in‐operando spatiotemporal imaging of the coupled elastodynamics using X‐ray diffraction microscopy of a VO 2 film channel device on TiO 2 substrate reveals two new surprises. First, the film channel bulges during the IMT, the opposite of the expected shrinking in the film undergoing IMT. Second, a microns thick proximal layer in the substrate also coherently bulges accompanying the IMT in the film, which is completely unexpected. Phase‐field simulations of coupled IMT, oxygen vacancy electronic dynamics, and electronic carrier diffusion incorporating thermal and strain effects suggest that the observed elastodynamics can be explained by the known naturally occurring oxygen vacancies that rapidly ionize (and deionize) in concert with the IMT (MIT). Fast electrical‐triggering of the IMT via ionizing defects and an active “IMT‐like” substrate layer are critical aspects to consider in device applications.

36 MATERIALS SCIENCE↗

Zero-Strain Metal-Insulator Transition by the Local Fluctuation of Cation Dimerization

The coupled electronic and structural transitions in metal-insulator transition (MIT) hinder ultrafast switching and ultimate endurance. Decoupling these transitions and achieving a zero-strain electronic MIT can overcome the fundamental limitations of MIT in solid materials. Here, this study demonstrates that iso-valent Ti dopants in supercooled VO 2 epitaxial films cause MIT with minimal hysteresis without changing unit-cell volume and crystal symmetry. The Ti dopants in the VO 2 lattice locally alter the configuration of V-V pairs, where the long-range ordering in V-V pairs is disrupted, and the nano-domains of V-V dimers are formed. Strikingly, these local V-V dimers persist even above the electronic transition temperature (T MI ), facilitating the zero-strain electronic MIT with nanoscale structural heterogeneity. The geometrically compatible interface between insulating and metallic phases drastically enhances switching speed and endurance during electrically and optically driven zero-strain MIT. In conclusion, this discovery offers a fresh perspective on the scientific understanding of MIT and the improved functionality in terms of device speed and reliability by decoupling electronic and structural transitions.

36 MATERIALS SCIENCE↗

Highly Efficient Room‐Temperature Spin‐Orbit‐Torque Switching in a Van der Waals Heterostructure of Topological Insulator and Ferromagnet

Abstract All‐Van der Waals (vdW)‐material‐based heterostructures with atomically sharp interfaces offer a versatile platform for high‐performing spintronic functionalities at room temperature. One of the key components is vdW topological insulators (TIs), which can produce a strong spin‐orbit‐torque (SOT) through the spin‐momentum locking of their topological surface state (TSS). However, the relatively low conductance of the TSS introduces a current leakage problem through the bulk states of the TI or the adjacent ferromagnetic metal layers, reducing the interfacial charge‐to‐spin conversion efficiency ( q ICS ). Here, a vdW heterostructure is used consisting of atomically‐thin layers of a bulk‐insulating TI Sn‐doped Bi 1.1 Sb 0.9 Te 2 S 1 and a room‐temperature ferromagnet Fe 3 GaTe 2, to enhance the relative current ratio on the TSS up to ≈20%. The resulting q ICS reaches ≈1.65 nm −1 and the critical current density J c ≈0.9 × 10 6 Acm −2 at 300 K, surpassing the performance of TI‐based and heavy‐metal‐based SOT devices. These findings demonstrate that an all‐vdW heterostructure with thickness optimization offers a promising platform for efficient current‐controlled magnetization switching at room temperature.

2D ferromagnet↗

Reversible Modification of Rashba States in Topological Insulators at Room Temperature by Edge Functionalization

Quantum materials with novel spin textures from strong spin-orbit coupling (SOC) are essential components for a wide array of proposed spintronic devices. Topological insulators have a necessary strong SOC that imposes a unique spin texture on topological states and Rashba states that arise on the boundary, but there is no established methodology to control the spin texture reversibly. Here, it is demonstrated that functionalizing Bi 2 Se 3 films by altering the step-edge termination directly changes the strength of SOC and thereby modifies the Rashba strength of 1D edge states. Scanning tunneling microscopy/spectroscopy shows that these Rashba edge states arise and subsequently vanish through the Se functionalization and reduction process of the step edges. The observations are corroborated by density functional theory calculations, which show that a subtle chemical change of edge termination fundamentally alters the underlying electronic structure. Importantly, fully reversible and repeatable switching of Rashba edge states across multiple cycles at room temperature is experimentally demonstrated. The results imply Se functionalization as a practical method to control SOC and spin texture of quantum states in topological insulators.

Rashba edge states↗

Quantum Magnetic Properties and Metal‐to‐Insulator Transition in Chemically Doped Calcium Ruthenate Perovskite

Ruthenates provide a comprehensive platform to study a plethora of novel properties, such as quantum magnetism, superconductivity, and magnetic fluctuation mediated metal–insulator transition (MIT). Herein, an overview of quantum mechanical phenomenology in calcium ruthenium oxide with varying compositions is provided. While the stoichiometric composition of exhibits non‐fermi liquid (FL) behavior with quasi‐criticality, chemically doped compounds depict prominent signatures of quantum magnetic fluctuations at low temperature that in some cases are argued to mediate in metal–insulator transition. In the case of cobalt‐doped , an unusual continuum fluctuation is found to persist deep inside the glassy phase of the material. These observations reflect the richness of the ruthenate research platform in the study of quantum magnetic phenomena of fundamental importance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Permanently Magnetized Insulating Thin-Film Devices by Reduction

A reduction-based manufacturing process for creating technologically important multilayer structures from lattice-matched ferromagnetic insulators and ferromagnetic conductors is reported. The process is demonstrated by growing a permanently magnetized double-layer structure, consisting of lattice-matched conducting (Ni,Co) and insulating (Ni 0.4 Co 0.6 ) 3 O 3 layers, through a single deposition cycle. The orientation of the metal cation network is preserved after reduction. Close-packing displacements of Ni and Co take place in such a manner that the in-plane hexagonal arrangement is preserved. This is critical for ensuring high-quality interfaces joining the layers. At room temperature the hysteresis loop is centered. At low temperature the oxide layer becomes ferrimagnetically ordered, accompanied by a shift of the hysteresis loop along the magnetic field axis. The shift is assigned to exchange bias phenomenon. Biaxial compressive strain is responsible for the required ferrimagnetic ordering. Finally, spin valves and closely related magnetoresistance random access memory and spin-transfer-torque magnetic random access memory devices are addressed as potential applications.

42 ENGINEERING↗

Evaluation of measuring thermal conductivity of isotropic and anisotropic thermally insulating materials by transient plane source (Hot Disk) technique

The transient plane source (TPS) technique, also referred as the Hot Disk method, has been widely used due to its ability to measure the thermal properties of an extensive range of materials (solids, liquids, and powder). Recently, it has been recognized that typical Hot Disk sensors can influence TPS results of thermally insulating materials and lead to an overestimation of thermal conductivity. Although improvements have been proposed, they have not yet been implemented in the commercial TPS, leaving researchers with non-standardized modifications or options provided by a commercial Hot Disk apparatus. An empirical study of thermally insulating materials such as extruded polystyrene (XPS) and aerogel blanket is conducted in order to address the factors that affect the reliability of thermal conductivity k obtained using the commercial TPS apparatus. Sensor size, input power, duration of the measurements, applied pressure, and, in the case of anisotropic materials, heat capacity are investigated, and the results are compared with those using a Heat Flow Meter apparatus. The effect of sensor size on the k value is ascribed to heat loss through connecting leads and is more pronounced in smaller sensors and in materials with lower k values . In the case of XPS and aerogel, the effect becomes minimal for sensors with a radius r ≥ 6.4 mm. The low input power yields a high scattering of the results and should be avoided. Applied contact pressure and the tested region of the specimen play an important role in experiments with low-density fibrous materials due to the large percentage of heat being transferred by radiation and the heterogeneous nature of the samples, respectively. Additionally, the sensitivity of anisotropic measurements to the value of the material’s volumetric heat capacity ( ρC p ) is shown, emphasizing the need for the precise determination.

thermal conductivity↗