Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Defect properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Thermal diffusivity and thermal conductivity of SiC composite tubes: the effects of microstructure and irradiation

Cladding thermal conductivity is an important physical property in assessing the performance of silicon carbide (SiC)-cladded fuels for nuclear reactors. However, there is a significant lack of reliable data, particularly for irradiated materials, because the geometry complicates the measurement. This study investigates the thermal diffusivity of coupons with a curvature, machined from SiC fiber–reinforced SiC matrix composite tubes, with and without neutron irradiation under light water reactor–relevant temperature and dose conditions. The tested materials included full composite and duplex SiC composite tubes. The measurements were conducted using a modern flash diffusivity apparatus. The analyzed area on the specimen during diffusivity testing was reduced for improved measurement accuracy due to sample curvature. Post-irradiation measurements showed that the effects of neutron irradiation on thermal conductivity (e.g. thermal defect resistivity) are different between SiC composite plates versus tubes. The difference was explained by higher matrix density of the tube than the plate. This study provides reliable thermal properties of prototypic SiC composite tubes useful for fuel performance modeling of SiC-based cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Multimodal microscopy of extended defects in β-Ga 2 O 3 (010) EFG crystals

Beta-phase gallium oxide (β-Ga 2 O 3 ) has attracted attention in recent years as a potentially low cost, large area substrate and active layer material for high power, high temperature power electronics and sensing devices. However, growth of β-Ga 2 O 3 crystals is complicated by easily activated (100) and (001) cleavage planes, the presence of low angle grain boundaries (LAGBs) and twins, and the potential formation of polycrystalline grains. In this study, β-Ga 2 O 3 crystals were grown by the edge-defined film-fed growth technique with an (010) principal face. Two crystals with apparently randomly formed high angle grain boundaries (HAGBs) were selected and analyzed by electron backscatter diffraction, electron channeling contrast imaging, and cathodoluminescence to investigate the nature of the LAGBs and the source of the HAGB formation. It was discovered that planar LAGBs lying parallel to the (010) plane exist in the region immediately preceding the start of an HAGB. Increased misorientation across the LAGB was observed, approaching the initiation of a new grain. We present multimodal microscopy characterization, correlating misorientation and variation in optoelectronic properties with LAGBs and the associated dislocations.

14 SOLAR ENERGY↗
DOE OSTI2025

Laser Powder Bed Fusion Manufactured Alloys 625 and 282 and Properties Relevant to Advanced Nuclear Components

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Large printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. Annealing at 1,180°C for 1 h followed by 4 h at 800°C in a high density of 50 nm γ′-strengthening precipitates as well as partial recrystallization resulted in a bimodal grain distribution. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Printing defects were the likely reason for the lower creep performance of LPBF 282 and could be suppressed by optimizing the build configuration. Printing 625 on an EOS M290 machine using the recommended EOS parameters resulted in a very low defect density. Superior creep strength at 725°C was observed for the as-printed LPBF 625 along the build direction when compared with wrought 625. No defect larger than ~50 µm could be detected by X-ray computed tomography in the as-printed conditions and after creep testing for 1,000 h at 725°C and 150 MPa. Small, needle-like δ-phase precipitates were observed after creep testing for 100 h at 725°C and 200 MPa. The rapid formation of the γ phase is directly related to the initial Nb and Mo segregation in the LPBF 625 cell walls, and its effect on the alloy’s high-temperature performance will be evaluated. Solution annealing was carried out at 1,150°C for 1 h and led to full recrystallization of the alloy. A decrease in strength and increase in ductility were observed after solution annealing, and the alloy recrystallization resulted in isotropic tensile properties at room temperature, contrary to what was observed for the as-printed LPBF 625.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Modeling the behavior of concentrated aqueous HNO 3 using machine learning interatomic potentials

We develop two multi-defect machine learning interatomic potentials (MLIPs) trained at the BLYP-D2 and PBE-D3 density functional theories using the DeepMD-kit, allowing for the investigation of structural and thermodynamic properties of nitric acid over a wide range of concentrations via molecular dynamics (MD) simulations. We directly compute the degree of dissociation, α, and pK a from MD simulations, revealing that HNO 3 behaves as a weaker acid at higher concentrations, noting that our standard-state pK a value is in excellent agreement with the experimental one. In general, good agreement is observed with experimental results such as α and density outside the training dataset, with only modest deviations at low-to-medium concentrations. We benchmark our custom multi-defect DeepMD MLIPs against foundational models MACE-MP0 and MACE-OFF23. The foundation models capture some aspects of HNO 3 /NO 3 − solvation in concentrated nitric acid but show noticeable density errors and miss subtle structural features relevant to spectroscopy, whereas the bespoke DeepMD MLIPs yield more compact solvation shells, reproduce density-concentration trends, and run ∼12–15× faster than MACE-MP0. Although classical FFs are still more efficient and match experimental densities better, they lack chemical reactivity and thus cannot predict α or pK a , underscoring the need for system-specific reactive MLIPs beyond universal MLIPs.

Dinpajooh, Mohammadhasan [Pacific Northwest Nation↗
DOE OSTI2025

Process-Microstructure-Property Relationships in Low Heat Input Wire-Arc Additive Manufacturing (WAAM) of Ni-Based Superalloy Haynes 282

Conference presentation on WAAM process optimization on Ni-based superalloy Haynes® 282®. This alloy is targeted for advanced power generation systems for its superior high temperature mechanical properties. Wire-arc additive manufacturing (WAAM) offers attractive cost and materials savings with high deposition rates. Based on initial build process optimization, WAAM blocks were made, and screened for defects using high-throughput CT scanning. The microstructural evolution in arc energy range of 250-700 J/mm was characterized in the as-built and aged conditions, using electron microscopy. Results showed self-consistent microstructure across conditions, with grain size dependence on arc energy, MC and M6C carbides in as-built, and blocky grain boundary M23C6 in as-heat-treated condition. Further reductions in as-built porosity were explored through 20+ combinations of H2 and CO2 additions to shielding gas. Initial results show improved wetting behavior, and bead overlap with up to 1% H2 and up to 0.25% CO2. Combination of experimentally determined datasets provided comprehensive understanding of process-structure-property relationships in WAAM Haynes 282.

Haynes 282↗
DOE OSTI2022

Design considerations for high entropy alloys in advanced nuclear applications

The demanding operating environments of advanced nuclear reactors require the development of new nuclear materials that can withstand their increased physical, chemical, thermal, and radiation-related challenges. High-entropy alloys (HEAs) have shown often-impressive mechanical, thermomechanical, and corrosion-resistant properties, and offer a massive, unexplored compositional space which allows for the targeted development of application-specific materials. Furthermore, although still in a nascent stage, research has shown that HEAs may exhibit unique irradiation tolerance, including reduced defect production and resistance to irradiation-induced swelling and hardening. The mechanisms behind this increased tolerance are not yet well-understood, although the HEA-specific attributes of a complex energy landscape, reduced thermal conductivity, and shift in defect migration energies and pathways provide promising explanations. Here this work assesses the current and future challenges faced by structural nuclear materials, identifying the specific applications in which HEAs may provide a competitive advantage compared to industry-standard materials with the aid of Ashby material selection maps. Considerations are provided for the design of future nuclear HEAs, including calculations of nuclear-relevant properties to assist in the initial down-selection of elements depending on application requirements (e.g., low neutron capture for in-core applications), narrowing the existing compositional space of HEAs to a manageable scope.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mixed excitonic nature in water-oxidized BiVO 4 surfaces with defects

BiVO 4 is a promising photocatalyst for efficient water oxidation, with surface reactivity determined by the structure of active catalytic sites. Surface oxidation in the presence of oxygen vacancies induces electron localization, suggesting an atomistic route to improve the charge transfer efficiency within the catalytic cycle. In this paper, we study the effect of oxygen vacancies on the electronic and optical properties at BiVO 4 surfaces upon water oxidation. We use density functional theory and many-body perturbation theory to explore the change in the electronic and quasiparticle energy levels and to evaluate the electron-hole coupling as a function of the underlying structure. Further we show that while the presence of defects alters the atomic structure and largely modifies the wave-function nature, leading to defect-localized states at the quasiparticle gap region, the optical excitations remain largely unchanged due to the substantial hybridization of defect and nondefect electron-hole transitions. Our findings suggest that defect-induced surface oxidation supports improved electron transport, both through bound and tunable electronic states and via a mixed nature of the optical transitions, expected to reduce electron-hole defect trapping.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-throughput spin-bath characterization of spin defects in semiconductors

Detailed knowledge of the local environments of spin defects in semiconductors, such as nitrogenvacancy (NV) centers in diamond or divacancies in silicon carbide, is crucial for optimizing control and entanglement protocols in quantum sensing and information applications. However, at present a direct experimental characterization of individual defect environments is not scalable, as conventional spin-bath measurements are time consuming and difficult to automate. Achieving high-throughput characterization requires short experiments to probe the spin bath. However, with fewer and noisier measurements, the inverse problem of recovering spin-bath properties from measured data becomes ill posed, with multiple spin baths having a high likelihood of yielding the same data. In this work, we present a set of computational tools to resolve the ill-posed inverse problem of recovering the atomic positions and hyperfine couplings of random nuclei surrounding spin defects from sparse, noisy experimental coherence data, which can be obtained in hours. Here, we use a trans-dimensional Bayesian approach that incorporates ab initio data to yield full posterior distributions over nuclear spin environments, enabling robust recovery from limited data. We also provide practical tools and guidelines to determine the limits of detectability for hyperfine couplings under specific dynamical decoupling sequences and sampling conditions. In addition, we demonstrate how the tools developed here, in combination with ab initio simulations of spin baths, can guide the design of efficient experimental protocols for application-specific high-throughput screening. To showcase the utility of our approach, we apply it to design fast dynamical decoupling experiments to characterize the spin baths often individual NV centers in diamond. While the primary focus is on accelerating spin-bath characterization of spin defects, this Bayesian approach also lays the foundation for digital-twin studies of spin defects, where a virtual model of the spin-defect system evolves in real time with ongoing experimental measurements. Together, the set of tools we designed and applied paves the way for scalable deployment of spin defects in semiconductors for quantum sensing and information applications.

Bayesian methods↗
DOE OSTI2023

Domain-dependent strain and stacking in two-dimensional van der Waals ferroelectrics

Van der Waals (vdW) ferroelectrics have attracted significant attention for their potential in next-generation nano-electronics. Two-dimensional (2D) group-IV monochalcogenides have emerged as a promising candidate due to their strong room temperature in-plane polarization down to a monolayer limit. However, their polarization is strongly coupled with the lattice strain and stacking orders, which impact their electronic properties. Here, we utilize four-dimensional scanning transmission electron microscopy (4D-STEM) to simultaneously probe the in-plane strain and out-of-plane stacking in vdW SnSe. Specifically, we observe large lattice strain up to 4% with a gradient across ~50 nm to compensate lattice mismatch at domain walls, mitigating defects initiation. Additionally, we discover the unusual ferroelectric-to-antiferroelectric domain walls stabilized by vdW force and may lead to anisotropic nonlinear optical responses. Our findings provide a comprehensive understanding of in-plane and out-of-plane structures affecting domain properties in vdW SnSe, laying the foundation for domain wall engineering in vdW ferroelectrics.

42 ENGINEERING↗
DOE OSTI2022

Effect of amine type on acidic toxic gas adsorption at ambient conditions on modified CuBTC

We report two amine-modified copper-based Metal Organic Frameworks (MOF (CuBTC)) of different surface chemical and textural features were synthesized and used as adsorbents of acidic toxic gases (NO 2 and H 2 S) in both moist (71% relative humidity (R.H.)) and dry conditions. The initial and exhausted samples were characterized by nitrogen adsorption, powder X-ray diffraction, scanning electron microscopy, thermal gravimetric analysis and Fourier transform infrared spectroscopy. The addition of melamine prevented full growth of CuBTC crystals and resulted in amorphous-like particles with sizes less than 200 nm. The material was non-porous with a small surface area. When urea was used as an amine source, the resulting particles maintained the overall octahedral shape of the parent CuBTC MOF and the material was more porous than the parent MOF. While the urea-modified CuBTC sample performed well as an NO 2 adsorbent in the presence of moisture, the reactivity of the melamine-modified sample and its physical properties provided a favorable environment for the removal of H 2 S. The incorporation of amines into the MOF structure also resulted in surface defects /open copper sites that favored the removal of toxic gases in dry conditions. The reactivity of the adsorbents with toxic gases was demonstrated by the changes in the adsorbent colors, in texture, and in surface chemistry (organic salts, complexes, sulfides and nitrates were formed).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Thin-film composite membranes based on hyperbranched poly(ethylene oxide) for CO 2 /N 2 separation

Cross-linked amorphous poly(ethylene oxide) (XLPEO) is one of the leading membrane materials for post-combustion CO 2 capture. For example, XLPEO prepared from poly(ethylene glycol) methyl ether acrylate (PEGMEA) exhibited CO 2 permeability of 570 Barrer and CO 2 /N 2 selectivity of 41 at 35 °C. However, these XLPEOs cannot be dissolved in coating solutions, making it impossible to be fabricated into thin-film composite (TFC) membranes using state-of-the-art manufacturing processes. In this study, we synthesized high molecular weight yet soluble HPEO via atom transfer radical polymerization (ATRP). These polymers were thoroughly characterized and compared with XLPEO, including thermal transitions, free volumes, and pure-gas sorption and permeation properties. A polymer with the best combination of CO 2 permeability (540 Barrer) and CO 2 /N 2 selectivity (43) was fabricated into defect-free TFC membranes with a thickness as thin as 506 ± 44 nm. When challenged with simulated flue gas containing water vapor at 35 °C for over 100 h, the membrane shows stable CO 2 permeance of 850 GPU and CO 2 /N 2 selectivity of 37, comparable to the leading commercial membranes for carbon capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Noncontact Andreev Reflection as a Direct Probe of Superconductivity on the Atomic Scale

Direct detection of superconductivity has long been a key strength of point-contact Andreev reflection. However, its applicability to atomic-scale imaging is limited by the mechanical contact of the Andreev probe. To this end, we present a new method to probe Andreev reflection in a tunnel junction, leveraging tunneling spectroscopy and junction tunability to achieve quantitative detection of Andreev scattering. This method enables unambiguous assignment of superconducting origins of current-carrying excitations, as well as detection of higher order Andreev processes in atomic-scale junctions. Herein, we furthermore revealed distinct sensitivity of Andreev reflection to natural defects, such as step edges, even in classical superconductors. The methodology opens a new path to nano- and atomic-scale imaging of superconducting properties, including disordered superconductors and proximity to phase transitions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Dynamic Behavior of Platinum Atoms and Clusters in the Native Oxide Layer of Aluminum Nanocrystals

Strong metal–support interactions (SMSIs) are well-known in the field of heterogeneous catalysis to induce the encapsulation of platinum (Pt) group metals by oxide supports through high temperature H 2 reduction. However, demonstrations of SMSI overlayers have largely been limited to reducible oxides, such as TiO 2 and Nb 2 O 5 . In this report we show that the amorphous native surface oxide of plasmonic aluminum nanocrystals (AlNCs) exhibits SMSI-induced encapsulation of Pt following reduction in H 2 in a Pt structure dependent manner. Reductive treatment in H 2 at 300 °C induces the formation of an AlO x SMSI overlayer on Pt clusters, leaving Pt single-atom sites (Ptiso) exposed available for catalysis. The remaining exposed Pt iso species possess a more uniform local coordination environment than has been observed on other forms of Al 2 O 3 , suggesting that the AlO x native oxide of AlNCs presents well-defined anchoring sites for individual Pt atoms. This observation extends our understanding of SMSIs by providing evidence that H 2 -induced encapsulation can occur for a wider variety of materials and should stimulate expanded studies of this effect to include nonreducible oxides with oxygen defects and the presence of disorder. It also suggests that the single-atom sites created in this manner, when combined with the plasmonic properties of the Al nanocrystal core, may allow for site-specific single-atom plasmonic photocatalysis, providing dynamic control over the light-driven reactivity in these systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Recent progress of MnBi 2 Te 4 epitaxial thin films as a platform for realising the quantum anomalous Hall effect

Since the first realisation of the quantum anomalous Hall effect (QAHE) in a dilute magnetic-doped topological insulator thin film in 2013, the quantisation temperature has been limited to less than 1 K due to magnetic disorder in dilute magnetic systems. With magnetic moments ordered into the crystal lattice, the intrinsic magnetic topological insulator MnBi 2 Te 4 has the potential to eliminate or significantly reduce magnetic disorder and improve the quantisation temperature. Surprisingly, to date, the QAHE has yet to be observed in molecular beam epitaxy (MBE)-grown MnBi 2 Te 4 thin films at zero magnetic field, and what leads to the difficulty in quantisation is still an active research area. Although bulk MnBi 2 Te 4 and exfoliated flakes have been well studied, revealing both the QAHE and axion insulator phases, experimental progress on MBE thin films has been slower. Furthermore, understanding how the breakdown of the QAHE occurs in MnBi 2 Te 4 thin films and finding solutions that will enable mass-produced millimetre-size QAHE devices operating at elevated temperatures are required. In this mini-review, we will summarise recent studies on the electronic and magnetic properties of MBE MnBi 2 Te 4 thin films and discuss mechanisms that could explain the failure of the QAHE from the aspects of defects, electronic structure, magnetic order, and consequences of their delicate interplay. Finally, we propose several strategies for realising the QAHE at elevated temperatures in MnBi 2 Te 4 thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Carrier capture and emission by substitutional carbon impurities in GaN vertical diodes

A model was developed for the operation of a GaN pn junction vertical diode which includes rate equations for carrier capture and thermally activated emission by substitutional carbon impurities and carrier generation by ionizing radiation. The model was used to simulate the effect of ionizing radiation on the charge state of carbon. These simulations predict that with no applied bias, carbon is negatively charged in the n-doped layer, thereby compensating n-doping as experimentally observed in diodes grown by metal-organic chemical vapor deposition. With reverse bias, carbon remains negative in the depletion region, i.e., compensation persists in the absence of ionization but is neutralized by exposure to ionizing radiation. This increases charge density in the depletion region, decreases the depletion width, and increases the capacitance. The predicted increase in capacitance was experimentally observed using a pulsed 70 keV electron beam as the source of ionization. In additional confirming experiments, the carbon charge-state conversion was accomplished by photoionization using sub-bandgap light or by the capture of holes under forward bias.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Radio-frequency magnetron sputter deposition of ultrathick boron carbide films

The deposition of thick B 4 C films with low residual stress by conventional direct-current magnetron sputtering is accompanied by the formation of dust particulates contaminating the target, chamber, and substrates and leading to the formation of nodular defects in films. Here, we demonstrate that the formation of particulates is greatly reduced during radio-frequency magnetron sputtering (RFMS). We systematically study properties of B 4 C films deposited by RFMS with a substrate temperature of 330 °C, a target-to-substrate distance of 10 cm, Ar working gas pressure in the range of 4.5–12.0 mTorr (0.6–1.6 Pa), and substrate tilt angles of 0°–80°. All films are x-ray amorphous. A columnar structure develops with increasing either Ar pressure or substrate tilt. For columnar films, the column tilt angle decreases with increasing Ar pressure, which we attribute to a corresponding increase in the width of the distribution of impact angles of deposition flux. In contrast to the Keller–Simmons rule, the deposition rate increases with increasing Ar pressure, which suggests a better coupling of the RF energy to the plasma processes that lead to target sputtering at higher pressures. There is a critical substrate tilt angle above which the total residual stress is close to zero. This critical substrate tilt angle is ~0° for an Ar pressure of 12 mTorr (1.6 Pa). The lower residual stress state, necessary for depositing ultrathick films, is characterized by a larger concentration of nanoscale inhomogeneities and decreased mechanical properties. Based on these results, RFMS deposition of 60-μm-thick B 4 C films is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2024

TEM Characterization of Neutron Irradiated HfAl3-Al Composite Specimens

Particles comprised of a thermal neutron absorbing material (HfAl3) are dispersed in a metal matrix material with high thermal conductivity (aluminum) to conduct the heat generated by neutron capture away from the fuel and materials. This metal matrix composite is very promising for use as a conduction-cooled neutron absorber and has the potential to be useful as a shroud or heat sink for testing advanced fast reactor fuels and materials in an existing thermal reactor. To design and optimize the absorber block system for advanced reactor designs, fundamental understanding of the irradiation effect on material properties is necessary. This dataset contains TEM characterization results of neutron irradiated HfAl3-Al composite specimens. It is focused on the irradiation induced defects (dislocation lines and loops) characterization using the on-zone axis bright field STEM technique. This data was collected using a FEI Tecnai G2 F30 S/TEM at the Microscopy and Characterization Suite (MaCS), Center for Advanced Energy Studies (CAES).

Guillen, Donna↗