Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Contact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Contact and crack problems for an elastic wedge

The contact and the crack problems for an elastic wedge of arbitrary angle are considered. The problem is reduced to a singular integral equation which, in the general case, may have a generalized Cauchy kernel. The singularities under the stamp as well as at the wedge apex were studied, and the relevant stress intensity factors are defined. The problem was solved for various wedge geometries and loading conditions. The results may be applicable to certain foundation problems and to crack problems in symmetrically loaded wedges in which cracks initiate from the apex.

Erdogan, F.↗
NASA NTRS1975

Analysis of dynamic capacity of low-contact-ratio spur gears using Lundberg-Palmgren theory

A concise mathematical model is developed for surface fatigue life of low-contact-ratio spur gears. The expected fatigue life of the pinion, gear, or gear sets may be calculated from the model. An equation for the dynamic capacity of the gear set was also derived in terms of the transmitted tangential tooth load which will give a 10-percent fatigue life of one million pinion revolutions. The theoretical life was compared with experimental data for a set of VAR AISI 9310 gears operating at a Hertz stress of 1.71X10 to the 9th power newtons per square meter (248,000 psi) and 10 000 revolutions per minute. Good agreement was obtained between the experimental and theoretical surface fatigue life of the gears.

Coy, J. J.↗
NASA NTRS1974

An investigation of traction in elastohydrodynamic point contacts using optical interferometry

An optical EHD machine is described which will measure the thickness of elastohydrodynamic lubricant films in rolling/sliding contacts while a traction force is applied to the film. A convenient way of plotting friction coefficient against slide/roll ratio is proposed. For 13 pure fluids with well-established physical properties, the value of the peak friction coefficient was found to lie between 0.011 and 0.09.

Gentle, C. R.↗
NASA NTRS1976

Connector contact-ring bus

Use of device eliminates crimp connectors and ferrules, resulting in compact termination assembly and efficient use of back-shell space. Pair of insulator rings, one at each end of assembly, provides spacing between disc caps and contact rings.

Ligon, J.↗
NASA NTRS1976

Infrared emission spectra from operating elastohydrodynamic sliding contacts

Infrared emission spectra from an operating EHD sliding contact were obtained through a diamond window for an aromatic polymer solute present in equal concentration in four different fluids. Three different temperature ranges, three different loads, and three different speeds for every load were examined. Very sensitive Fourier spectrophotometric (Interferometric) techniques were employed. Band Intensities and band intensity ratios found to depend both on the operating parameters and on the fluid. Fluid film and metal surface temperatures were calculated from the spectra and their dependence on the mechanical parameters plotted. The difference between these temperatures could be plotted against shear rate on one curve for all fluids. However, at the same shear rate the difference between bulk fluid temperature and diamond window temperature was much higher for one of the fluids, a traction fluid, than for the others.

Lauer, J. L.↗
NASA NTRS1965

Thermal contact conductance between metals in a vacuum environment

Basic heat transfer data for structural materials used in the Saturn 1B/V 1U component case structural design were obtained. The main emphasis is on thermal contact conductance between dissimilar metallic surfaces, since thermal conductivity values within solids have been sufficiently established previously. The test program outline and test results are described. The following materials were tested: aluminum 6061-T6 (12 samples), aluminum 356 (as cast), almag 35 (as cast), magnesium AZ91C-T4 (4 samples), and mag lithium LA-141 (2 samples).

Source record↗
NASA NTRS1975

Infrared emission spectra of elastohydrodynamic contacts

A small diamond disk mounted as a window in a steel plate was covered with test fluid, and a weighted steel ball was rotated over the window so as to form a sliding elastohydrodynamic (EHD) contact region. Some of the radiant energy generated in this region, both in the fluid and at the boundaries, passed through the window into an infrared interferometer, giving rise to an emission spectrum. This spectrum could be separated into contributions from the fluid and from the ball surface, making it possible, by appropriate calibrations, to estimate their temperatures separately under operating conditions. Moreover, the shape of the discrete spectral bands of the fluid permitted some inferences on its state. Two fluids were studied under identical mechanical conditions, a polyester and a naphthenic oil, each containing an equal amount of polymethylstyrene as a spectral indicator. Differences of band intensity, band width, and frequency could, therefore, be attributed to differences in the behavior of the base fluid.

Lauer, J. L.↗
NASA NTRS1977

Low-resistance contacts for GaAlAs/GaAs cells

Bimetallic contacts utilizing palladium and aluminum, gold, silver, or chromium, are used in reduction of series resistance in GaAlAs/GaAs solar cells, thereby improving cell reliability.

Hovel, H. J.↗
NASA NTRS1976

Effect of interfacial oxide layers on the current-voltage characteristics of Al-Si contacts

Aluminum-silicon contacts with very thin interfacial oxide layers and various surface impurity concentrations are studied for both n and p-type silicon. To determine the surface impurity concentrations on p(+)-p and n(+)-n structures, a modified C-V technique was utilized. Effects of interfacial oxide layers and surface impurity concentrations on current-voltage characteristics are discussed based on the energy band diagrams from the conductance-voltage plots. The interfacial oxide and aluminum layer causes image contrasts on X-ray topographs.

Porter, W. A.↗
NASA NTRS1976

Isothermal elastohydrodynamic lubrication of point contacts. III: Fully flooded results

The influence of the ellipticity parameter and the dimensionless speed U, load W, and material G parameters on minimum film thickness was investigated. The ellipticity parameter k was varied from 1 (a ball-on-plate configuration) to 8 (a configuration approaching a line contact). The dimensionless speed parameter was varied over a range of nearly two orders of magnitude. And the dimensionless load parameter was varied over a range of one order of magnitude. Conditions corresponding to the use of solid materials of bronze, steel, and silicon nitride and lubricants of paraffinic and naphthenic mineral oils were considered in obtaining the exponent on the dimensionless material parameter.

Hamrock, B. J.↗
NASA NTRS1977

Elastohydrodynamic lubrication of elliptical contacts for materials of low elastic modulus. 1: Fully flooded conjunction

Elastohydrodynamic lubrication concepts of conjunctions of elliptical form are applied to materials of low elastic modulus. The influence of the ellipticity parameter and the dimensionless speed, load, and material parameters on minimum film thickness for these materials has been investigated. The ellipticity parameter was varied from a ball on plate configuration to a configuration approaching a line contact. The dimensionless speed and load parameters were varied by 1 order of magnitude. Seventeen different cases were used to generate minimum and central film thickness relations. Contour plots are presented that illustrate the pressure distribution and film thickness in the conjunction.

Hamrock, B. J.↗
NASA NTRS1976

Effects of load, speed, and surface roughness on sliding EHD contact temperatures

An infrared technique has been used to determine the effects of load, speed and surface roughness on temperature in a sliding elastohydrodynamic (EHD) point contact. Ball surface temperatures are reported for sliding speeds of 0.35 to 5.08 m/s at 0.52 to 2.03 GN/per sq m maximum pressure with surface roughness in the range 0.01 to 0.38 micron c.l.a. The relationship between asperity interaction, as measured by relocation surface profilimetry and high frequency temperature measurements, and the ratio of film thickness to surface roughness has also been studied.

Nagaraj, H. S.↗
NASA NTRS1976

Isothermal elastohydrodynamic lubrication of point contacts. III - Fully flooded results

Procedures outlined by the authors in an earlier publication (1976) on theoretical formulation for isothermal elastohydrodynamic lubrication of point contacts are used to assess the influence of the ellipticity parameter and the dimensionless speed, load, and material parameters on minimum film thickness. Conditions equivalent to using solid materials of bronze, steel, and silicon nitride, and lubricants of paraffinic and naphthenic mineral oils are considered in obtaining the exponent on the dimensionless material parameter. Thirty-four different cases are used to generate the fully flooded film thickness formula. A fully flooded condition is said to exist when the inlet distance of the conjunction ceases to influence in any significant way the minimum film thickness. Contour plots are also shown that indicate in detail the pressure spike and two side lobes in which the minimum film thickness occurs.

Hamrock, B. J.↗
NASA NTRS1977

Parametric amplification and oscillation at 36 GHz using a point-contact Josephson junction

The paper reports observation of doubly degenerate parametric amplification and oscillation at 36 GHz from a single point-contact Josephson junction. The experimental results agree qualitatively with theoretical calculations based on the resistively shunted junction model. The estimated noise temperature of an amplifier with 11 dB net gain is consistent with zero, but has an upper limit of 50 K. Attempts to observe parametric amplification in the singly degenerate mode with a pump frequency of 72 GHz were not successful.

Taur, Y.↗
NASA NTRS1976

The morphological evolution of mare-highland contacts - A potential measure of relative mare surface age

The uniform breaks in slopes along many mare-highland contacts may be debris aprons transported primarily by impact erosion at relatively slow rates. Other suggestions, such as the 'high lava mark' hypothesis, appear inadequate to explain all of the unique characteristics of these widespread features. There is a reasonable correlation of overall slope form (profile) and apron distribution with established mare age provinces. Distinctive debris aprons in the younger maria could represent the initial stages of lunar slope degradation produced mainly by the postmare impact flux. The growth of debris aprons must be qualitatively related to the impact flux recorded on adjacent mare surfaces and could provide an approximate means of extrapolating relative mare ages to highland scarps and crater walls. By combining detailed measurements of lunar slopes with development of a realistic model for impact modification of these features, approximate limits for the cumulative lunar flux distribution through time might be derived.

Young, R. A.↗