Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Configuration interaction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Stochastic minibatch approach to the ptychographic iterative engine

The ptychographic iterative engine (PIE) is a widely used algorithm that enables phase retrieval at nanometer-scale resolution over a wide range of imaging experiment configurations. By analyzing diffraction intensities from multiple scanning locations where a probing wavefield interacts with a sample, the algorithm solves a difficult optimization problem with constraints derived from the experimental geometry as well as sample properties. The effectiveness at which this optimization problem is solved is highly dependent on the ordering in which we use the measured diffraction intensities in the algorithm, and random ordering is widely used due to the limited ability to escape from stagnation in poor-quality local solutions. In this study, we introduce an extension to the PIE algorithm that uses ideas popularized in recent machine learning training methods, in this case minibatch stochastic gradient descent. Our results demonstrate that these new techniques significantly improve the convergence properties of the PIE numerical optimization problem.

47 OTHER INSTRUMENTATION↗

Modeling wiggler with hard edge dipoles

Wigglers and undulators are used as devices for generating synchrotron radiation. They are also used for modification of various beam properties circulating in a storage ring. Basic ‘dumping wiggler’ is used for change of the damping time, equilibrium emittance, and energy spread. In damping wigglers are used to increase the damping rate of the energy spread induced by the beam-beam interaction. The commonly used MAD and Elegant software has only simplified planar wiggler configuration and no model for a helical wiggler.

43 PARTICLE ACCELERATORS↗

Centaur Standard Shroud (CSS) static limit load structural tests

The structural capabilities of the jettisonable metal shroud were tested and the interaction of the shroud with the Centaur stage was evaluated. A flight-configured shroud and the assemblies of the associated Centaur stage were tested for applied axial and shear loads to flight limit values. The tests included various thermal, pressure, and load conditions to verify localized strength capabilities, to evaluate subsystem performance, and to determine the aging effect on insulation system properties. The tests series verified the strength capabilities of the shroud and of all associated flight assembles. Shroud deflections were shown to remain within allowable limits so long as load sharing members were connected between the shroud and the Centaur stage.

Eastwood, C.↗

Numerical image manipulation and display in solar astronomy

The paper describes the system configuration and data manipulation capabilities of a solar image display system which allows interactive analysis of visual images and on-line manipulation of digital data. Image processing features include smoothing or filtering of images stored in the display, contrast enhancement, and blinking or flickering images. A computer with a core memory of 28,672 words provides the capacity to perform complex calculations based on stored images, including computing histograms, selecting subsets of images for further analysis, combining portions of images to produce images with physical meaning, and constructing mathematical models of features in an image. Some of the processing modes are illustrated by some image sequences from solar observations.

Levine, R. H.↗

Spacecraft flight control with the new phase space control law and optimal linear jet select

An autopilot designed for rotation and translation control of a rigid spacecraft is described. The autopilot uses reaction control jets as control effectors and incorporates a six-dimensional phase space control law as well as a linear programming algorithm for jet selection. The interaction of the control law and jet selection was investigated and a recommended configuration proposed. By means of a simulation procedure the new autopilot was compared with an existing system and was found to be superior in terms of core memory, central processing unit time, firings, and propellant consumption. But it is thought that the cycle time required to perform the jet selection computations might render the new autopilot unsuitable for existing flight computer applications, without modifications. The new autopilot is capable of maintaining attitude control in the presence of a large number of jet failures.

Bergmann, E. V.↗

A study of canard-wing interference using experimental pressure data at transonic speeds

The canard had an exposed area of 28.0 percent of the wing reference area and was located in the chord plane of the wing or in a position 18.5 percent of the wing mean geometric chord above or below the wing chord plane. The canard leading edge sweep was 51.7 deg and the wing leading-edge sweep was 60 deg. The results indicated that the direct canard downwash effects on the wing loading are limited to the forward half of the wing directly behind the canard. The wing leading-edge vortex is located farther forward for the wing in the presence of the canard than for the wing-alone configuration. The wake, from the canard located below the wing chord plane, physically interacts with the wing inboard surface and produces a substantial loss of wing lift. For the Mach number 0.70 case, the presence of the wing increased the loading on the canard for the higher angles of attack. However, at Mach numbers of 0.95 and 1.20, the presence of the wing had the unexpected result of unloading the canard.

Gloss, B. B.↗

Manned space platforms, payloads and tending

A concept has been developed for providing for a permanent manned presence in space for science, applications, and technology plus growth potential to support major future operational missions. An initial crew of two to four is accommodated along with installations for interior, exterior and tended payloads. Tended payloads support includes servicing of remote free-flying spacecraft, basing of reusable orbital transfer vehicles and basing of teleoperator-mounted payloads for near-station excursions. Candidate payloads, plus configuration, flight operation, subsystem and ground logistics aspects are described, as are Shuttle interactions.

Runge, F. C.↗

Elements of computational engine-airframe integration

Computerized flow simulation methods are being developed to refine the traditional engine-airframe integration process. These analyses reduce design risk, minimize wind tunnel and flight test requirements, and provide detailed design information not available by any other means. This paper describes computational tools which have matured sufficiently to permit project applications. Several applications are combined with research studies to illustrate the prediction of high-speed nonlinear phenomena associated with engine inlet flow rate, nacelle shape and position, afterbody shape and integration, propeller slipstream interactions, airframe-induced inlet flow, and pylon integration. Both fighter and transport configurations are used to highlight current capabilities and future requirements.

Boppe, C. W.↗

Modeling of gamma/gamma-prime phase equilibrium in the nickel-aluminum system

A theoretical model is proposed for the determination of phase equilibrium in alloys, taking into consideration dissimilar lattice parameters. Volume-dependent pair interactions are introduced by means of phenomenological Lennard-Jones potentials and the configurational entropy of the system is treated in the tetrahedron approximation of the cluster variation method. The model is applied to the superalloy-relevant, nickel-rich, gamma/gamma-prime phase region of the Ni-Al phase diagram. The model predicts reasonable values for the lattice parameters and the enthalpy of formation as a function of composition, and the calculated phase diagram closely approximates the experimental diagram.

Sanchez, J. M.↗

Ignition and Wind Effects on the Transition to Flame Spread in a Microgravity Environment

The fundamental processes involved in ignition and flame spread have been extensively studied, they are generally studied separately without combining ignition and flame spread through the transition process. Moreover, the majority of the flame spread studies assume steady state flame spread. To study the transient aspects of ignition and the transition to flame spread, a time-dependent numerical model has been developed in which a thin strip is ignited along its width with either a pilot wire, radiative source, or both. For this configuration, the model is two-dimensional. Ignition is initiated away from either end of the sample, and two different flame fronts spread in opposite directions; one flows with and the other against a prescribed external flow. Usually, the flame spread is initiated by ignition at one end of the sample with or against a slow external flow, yielding one flame front. The present configuration is more realistic than the one flame front case because there is interaction between the two flames during the ignition and transition stages.

McGrattan, Kevin B.↗

Large-Eddy/Lattice Boltzmann Simulations of Micro-blowing Strategies for Subsonic and Supersonic Drag Control

This report summarizes the progress made in the first 8 to 9 months of this research. The Lattice Boltzmann Equation (LBE) methodology for Large-eddy Simulations (LES) of microblowing has been validated using a jet-in-crossflow test configuration. In this study, the flow intake is also simulated to allow the interaction to occur naturally. The Lattice Boltzmann Equation Large-eddy Simulations (LBELES) approach is capable of capturing not only the flow features associated with the flow, such as hairpin vortices and recirculation behind the jet, but also is able to show better agreement with experiments when compared to previous RANS predictions. The LBELES is shown to be computationally very efficient and therefore, a viable method for simulating the injection process. Two strategies have been developed to simulate multi-hole injection process as in the experiment. In order to allow natural interaction between the injected fluid and the primary stream, the flow intakes for all the holes have to be simulated. The LBE method is computationally efficient but is still 3D in nature and therefore, there may be some computational penalty. In order to study a large number or holes, a new 1D subgrid model has been developed that will simulate a reduced form of the Navier-Stokes equation in these holes.

Menon, Suresh↗

Combined In-Plane and Through-the-Thickness Analysis for Failure Prediction of Bolted Composite Joints

Although two-dimensional methods provide accurate predictions of contact stresses and bolt load distribution in bolted composite joints with multiple bolts, they fail to capture the effect of thickness on the strength prediction. Typically, the plies close to the interface of laminates are expected to be the most highly loaded, due to bolt deformation, and they are usually the first to fail. This study presents an analysis method to account for the variation of stresses in the thickness direction by augmenting a two-dimensional analysis with a one-dimensional through the thickness analysis. The two-dimensional in-plane solution method based on the combined complex potential and variational formulation satisfies the equilibrium equations exactly, and satisfies the boundary conditions and constraints by minimizing the total potential. Under general loading conditions, this method addresses multiple bolt configurations without requiring symmetry conditions while accounting for the contact phenomenon and the interaction among the bolts explicitly. The through-the-thickness analysis is based on the model utilizing a beam on an elastic foundation. The bolt, represented as a short beam while accounting for bending and shear deformations, rests on springs, where the spring coefficients represent the resistance of the composite laminate to bolt deformation. The combined in-plane and through-the-thickness analysis produces the bolt/hole displacement in the thickness direction, as well as the stress state in each ply. The initial ply failure predicted by applying the average stress criterion is followed by a simple progressive failure. Application of the model is demonstrated by considering single- and double-lap joints of metal plates bolted to composite laminates.

Kradinov, V.↗

Shaped Recess Flow Control

One or more embodiments of techniques or systems for shaped recess flow control are provided herein. A shaped recess or cavity can be formed on a surface associated with fluid flow. The shaped recess can be configured to create or induce fluid effects, temperature effects, or shedding effects that interact with a free stream or other structures. The shaped recess can be formed at an angle to a free stream flow and may be substantially "V" shaped. The shaped recess can be coupled with a cooling channel, for example. The shaped recess can be upstream or downstream from a cooling channel and aligned in a variety of manners. Due to the fluid effects, shedding effects, and temperature effects created by a shaped recess, lift-off or separation of cooling jets of cooling channels can be mitigated, thereby enhancing film cooling effectiveness.

Shyam, Vikram↗

Aerospace Cognitive Engineering Laboratory (ACELAB) Simulator for Electric Vertical Takeoff and Landing (eVOTL) Research and Development

A new generation of aerospace innovators are looking for ways to quickly and efficiently transport people in a safe and environmentally friendly manner. In the not-too-distant future, passengers and goods are expected to routinely fly aboard a new breed of cleaner, smarter air vehicles. This represents a new and significant challenge to the Federal Aviation Agency (FAA) which is responsible for aircraft certification, pilot licensing, operating approval and airspace integration. To help streamline this process, NASA has formulated its Advanced Air Mobility (AAM) project to provide research capabilities for development and evaluation of these new concepts and an environment where industry and regulators can work together to understand the requirements and work toward consensus standards for the new market. This paper will describe the development of the Aerospace Cognitive Engineering Lab Rapid Automation Test (ACELeRATE) simulator. ACELeRATE is an adaptable fixed-base aircraft simulator focused on the investigation of the performance and interaction of pilots and increasingly automated aircraft systems. ACELeRATE can be re-configured to support various simulation environments. The simulator includes a simple reconfigurable cockpit placed within a 10-foot spherical dome with a cluster of real-time image generators, high-resolution displays and highly realistic scenery with the surrounding digital terrain and required cultural area details (e.g., hangars, runways, ramp areas, taxiways, test range apparatus, buildings with designated rooftop landing areas, and other man-made 3D structures). This paper will also describe the various hardware and software tools employed in the ACELeRATE simulator, including engineering tools used by NASA for electric Vertical Takeoff and Landing (eVTOL) vehicle equations of motion, wind-model simulation in an urban environment, as well as the various modeling techniques and tools used to quickly generate highly realistic 3D terrain models for low level flight including urban terrain and obstacle depictions.

AAM Simulation Cockpit↗

RApid Blade and Blade-Vortex InTeraction (RABBIT) GUI implementation via MATLAB Application Designer

Rotorcraft noise source identification and reduction is crucial to the emergence of the Urban Air Mobility (UAM) market. One key rotor noise source is Blade Vortex Interaction (BVI), caused by the rotor wake interacting with the rotor blades. The low-fidelity RApid Blade and Blade-Vortex InTeraction (RABBIT) tool was created to predict the location and characteristics of Blade-Vortex Interaction (BVI) noise. RABBIT enables engineers to quickly locate and understand designs or configurations that cause significant BVI noise. Furthermore, RABBIT can identify the time and location of blade overlap for coaxial rotors. RABBIT is not a general acoustic prediction tool, but instead utilizes vortex and wake parameters to visualize and predict only BVI noise. To date, RABBIT has been validated against CAMRAD II and ANOPP2/AARON for three NASA Revolutionary Vertical Lift Technology (RVLT) concept vehicles: the Quiet Single Main Rotor (QSMR), Side-by-Side, and Quadrotor. RABBIT has been shown to be a useful BVI prediction tool capable of visualizing BVI as a function of various parameters. Impulse factor and time rate of change of loading allows for a unique BVI prediction technique that provides information on impulse strength, location, and frequency. This presentation will highlight how MATLAB’s App Designer was utilized to enable users to navigate RABBIT easily and efficiently without prior experience with MATLAB or rotorcraft acoustics. RABBIT users can build and view rotors in real time with options to control blade chord, radius, phasing, and airfoil geometry. Furthermore, multiple rotors can be combined to create state-of-the-art multi-rotor vehicles or fleets. Editable tables, sliding bars, and push buttons were implemented within MATLAB’s App Designer for RABBIT’s GUI to allow engineers and designers to predict low order acoustic impact of BVI occurrences.

Natasha Lydia Schatzman↗

Systems and methods for relay ionization

The invention generally relates to systems and methods for relay ionization of a sample. In certain aspects, the invention provides systems that include an ion source that generates ions, a sample emitter configured to hold a sample, and a mass spectrometer. The system is configured such that the ions generated by the ion source are directed to interact with the sample emitter, thereby causing the sample to be discharged from the sample emitter and into the mass spectrometer.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Alfalfa

Alfalfa-based testbeds enable building equipment, control products, and workforce development tools to interact with dynamic building simulations representing the desired building, system, weather, and grid configuration. Alfalfa is used to de-risk implementation of load flexibility prior to field deployment, reducing the costs and timelines associated with adoption of decarbonization technology at the grid edge.

building energy modeling↗

Electromagnetic production of kaons on the nucleon

Studies of the electromagnetic production of strange quarks started in the 1950s as something of a curiosity that puzzled experimentalists and theorists alike. Eventually, a nascent understanding of these processes began to take shape through the first pioneering experiments dedicated to explore photo- and electroproduction that were carried out in the period from the 1950s to the 1980s. As the datasets increased, concomitant advances in theoretical models were realized. However, these initial studies also made clear that more precise data was essential to continue to move forward. A paradigm shift occurred in the 1990s with the development of second-generation facilities at ELSA, MAMI, SPring-8, and JLab. High-intensity, high duty-factor accelerators, coupled with novel detector systems and advances in computing and readout electronics, brought nuclear physics experiments forward by orders of magnitude in counting statistics compared to the first-generation efforts. This was an utter boon to strangeness physics investigations, and to date, more than 50 dedicated experiments in kaon photo- and electroproduction have been completed at facilities around the world, leading to a host of experimental observables that have enabled significant advances in the exploration of strongly interacting systems that decay via $s\bar{s}$ quark pair creation. These data have proven to be an essential complementary pathway to study the spectrum and structure of the excited states of the nucleon, and the search for missing and exotic baryon configurations. As well, investigations in these channels are requisite for exploring hypernuclear production as a probe of the $YN$ interaction and for studies of the electromagnetic form factors of strange mesons. This review was designed to provide the first-ever in-depth overview of both the experimental and theoretical progress in the field of the electromagnetic production of strangeness. This work looks back over 70 years of past developments, discusses ongoing work and near-term plans, and details future possibilities being considered for third-generation facilities. Extensive lists of the available datasets and theoretical models are provided, together with a comprehensive supporting bibliography of the field. Throughout this work, the primary impacts of these explorations are highlighted, along with connections to a wide range of related phenomenological applications. An important goal of this review is to provide a complete, (reasonably) self-contained guide into this field prepared at a level that is relevant for both new and seasoned scientists, whether experimentalists, phenomenologists, or theorists, to better understand what has been accomplished by so many dedicated folks-each building on what has come before-and to appreciate the exciting future potential for continued studies in this area.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗