Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONDUCTIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

The Nonuniversality of the Frequency Dependence of the Conductivity in Disordered Nanogranulated Systems

The real part of the high-frequency phononless conductivity is calculated in the pair approximation for a disordered array of densely packed spherical nanogranules. The generalization of the theory of phononless conductivity for systems with point impurities to systems with localized finite sizes (arrays of nanogranules or quantum dots) reveals that the high-frequency conductivity depends on the distribution function of the distances between the surfaces of granules P(w). This is expected to cause the discrepancy of the real part of the conductivity σ{sub 1}(ω) from the linear frequency dependence. In the vicinity of the frequency ω ~ ω{sub c} = 2I{sub 0}/ℏ (here I{sub 0} is a preexponential factor of the resonance integral) for disordered granulated systems is likely to deviate from the universality σ{sub 1}(ω) ~ ω{sup s} (s ≈ 1) due to the attenuation of the frequency dependence σ{sub 1}(ω) of the conductivity and its nonmonotonicity. The nonmonotonicity of σ{sub 1}(ω) must arise at lower frequencies as a result of decreased preexponential factor I{sub 0} of the resonance integral with increasing granule size.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Impact of Humidity on Charge Transport in Proton-Conducting Perovskites AZr{sub 0.95}Sc{sub 0.05}O{sub 3 – α} (A = Ca, Sr, Ba) Exposed to an Oxidative Atmosphere

The total, bulk, and grain boundary conductivities of proton-conducting zirconates of general formula AZr{sub 0.95}Sc{sub 0.05}O{sub 3 – α} (AZS), where A = Ca, Sr, Ba, are measured in air with different humidity levels. The conductivity is measured using the four-probe dc method (600–900°C) and impedance spectroscopy (30–800°C). The impact of humid atmosphere on the total, bulk, and grain boundary conductivities of the AZS system is studied at different humidity levels: p{sub H{sub 2O}} = 0.04, 0.61, and 2.5 kPa. Humidity is found to have a considerable effect on the conductivity of our CaZS and BaZS at lower temperatures, suggesting the likelihood of hydronium ion-mediated transport.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Realizing the Potential of Micro-Phase Separated Block Copolymer Electrolytes: Ion Domain Connectivity Plays a Prominent Role in Ion Conduction

Block copolymer electrolytes (BCEs) offer the prospect of membranes with high ionic conductivity at lower ion-exchange capacities leading to membranes with robust mechanical properties. However, the microphase separated structure of such BCE membranes and its impact on membrane conductivity is poorly understood. Most studies assume that aggregated ionic domains in microphase separated BCEs, or random copolymers, is sufficient to foster facile ion conductivity. However, microphase separation alone cannot spur rapid ion conduction. In this paper, we demonstrate that ion domain connectivity greatly influences ion conductivity in BCEs. The results emphasize the importance of maximizing ion domain connectivity while minimizing terminal defects to realize BCEs with optimal ion transport properties.

36 MATERIALS SCIENCE↗

Effect of Off-Stoichiometry on Electrical Conductivity in Ni-Fe and Mn-Co Spinel Systems

This study seeks to clarify the effects of off-stoichiometry on the electrical conductivity of spinels in the (Ni,Fe) 3 O 4 and (Mn,Co) 3 O 4 systems. Spinels with the compositions Ni x Fe 3–x O 4 (where x = 0.85, 0.875, 0.9, 1.0, 1.05, and 1.15) and Mn x Co 3–x O 4 (where x = 1.0, 1.2, 1.35, 1.5, 1.75, and 2.0) were prepared using conventional solid-state process. Electrical conductivity measurements were taken between 500 °C and 800 °C using the 4-point DC method. The conductivity in Ni-Fe spinels increased with increasing Fe content. Similarly, the conductivity of Mn-Co spinels increased drastically with increasing Co content. The coefficients of thermal expansion (CTEs) of these samples were also evaluated. All the (Ni,Fe) 3 O 4 spinels were found to exhibit excellent CTE matching with prospective stack components. However, thermal expansion characteristics were highly dependent on the composition in the (Mn,Co) 3 O 4 system, and only a narrow range of compositions was well-matched in CTE with prospective stack components. The significant effect of cation off-stoichiometry and sample preparation on the electrical behavior of spinels was discussed as a possible explanation for the large discrepancies in reported conductivity values for both systems.

08 HYDROGEN↗

Understanding Chemo-Mechanical Stability of Protonic Ceramic Cells Through Electronic Conduction in the BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3-δ Electrolyte

BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3-δ (BCZYYb) is a promising ceramic electrolyte for reversible protonic ceramic cells. It is reported that BCZYYb-based cells show excellent long-term durability, particularly in the electrolysis mode, in contrast to the cells based on the conventional electrolyte yttria-stabilized zirconia. In this study, we investigate the chemo-mechanical stability behavior (a low tendency of delamination) of the BCZYYb-based protonic ceramic cells in terms of local electronic conduction in the electrolyte. The local electronic conductivity of the BCZYYb electrolyte is determined using Pt-probe-embedded cells near each electrode interface. The BCZYYb electrolyte exhibits sufficient p-type conductivity (∼10 −3 S cm −1 ) near the oxygen electrode (corresponding p O 2 : 5.27–21 × 10 −2 atm) and n-type conductivity (∼10 −4 S cm −1 ) near the hydrogen electrode (corresponding p O 2 : 0.99–1.30 × 10 −24 atm) at 600 °C. A standard cell is prepared and tested over long-term in the fuel cell (at positive and negative voltages) and electrolysis modes. The cell exhibits stable performance without delamination or cracks in both operating modes, owing to local electronic conduction.

Electrochemistry↗

Solvent effects on polysulfide redox kinetics and ionic conductivity in lithium-sulfur batteries

Lithium-sulfur (Li-S) batteries have high theoretical energy density and low raw materials cost compared to present lithium-ion batteries and are thus promising for use in electric transportation and other applications. A major obstacle for Li-S batteries is low rate capability, especially at the low electrolyte/sulfur (E/S) ratios required for high energy density. Herein, we investigate several potentially rate-limiting factors for Li-S batteries. We study the ionic conductivity of lithium polysulfide solutions of varying concentration and in different ether-based solvents and their exchange current density on glassy carbon working electrodes. We believe this is the first such investigation of exchange current density for lithium polysulfide in solution. Exchange current densities are measured using both electrochemical impedance spectroscopy and steady-state galvanostatic polarization. In the range of interest (1-8 M [S]), the ionic conductivity monotonically decreases with increasing sulfur concentration while exchange current density shows a more complicated relationship to sulfur concentration. The electrolyte solvent dramatically affects ionic conductivity and exchange current density. Finally, the measured ionic conductivities and exchange current densities are also used to interpret the overpotential and rate capability of polysulfide-nanocarbon suspensions; this analysis demonstrates that ionic conductivity is the rate-limiting property in the solution regime (i.e. between Li 2 S 8 and Li 2 S 4 ).

25 ENERGY STORAGE↗

High Resolution Aerosol Jet Printed Components with Electrodeposition-Enhanced Conductance

Aerosol Jet Printing (AJP) is one technique of additive manufacturing used in the printing of electronics components. AJP enables the patterning of features at the ~10 μm–100 μm scale based on hardware and print parameters. Additionally, optimization of print conditions enables the printing of high-resolution features with linewidths approaching 10 μm. The aerosol jet printing of electronic parts can be limited by the conductivities which are achievable by Ag nanoparticle inks (typically 15%–25% of bulk Ag). For certain electronics applications, the increased conductivity produces unacceptable loses during operation and methods are needed to increase the conductance of the devices without sacrificing resolution. Here, we report on the AJP of inductor spirals conductor traces of linewidth 50 μm separated by 55 μm gaps. The conductivity of these features is enhanced by electrodeposition of Cu onto the Ag, resulting in a decrease in resistance of 35–45x. Impedance measurements demonstrate that the addition of Cu by electrodeposition to a 27-turn spiral inductor resulted in an inductance of 3.6 μH. Finally, we demonstrate the use of a lift-off process to produce free-standing, flexible, conductive films using AJP.

36 MATERIALS SCIENCE↗

Characterization of Grain‐Size Distribution, Thermal Conductivity, and Gas Diffusivity in Variably Saturated Binary Sand Mixtures

Core Ideas Parameterized models are relevant to applications where different porous media mixtures are used. Models include a grain‐size distribution function to describe bimodal behavior for binary mixtures. Improved model describes observed thermal conductivity–saturation relations for binary mixtures. Combined Buckingham–Penman model used to describe observed gas diffusivity–air content relations. This work is relevant for proper simulation of mixed porous media. Characterization of differently textured porous materials, as well as different volumetric porous media mixtures, in relation to mass and heat transport is vital for many engineering and research applications. Functional relations describing physical (e.g., grain‐size distribution, total porosity), thermal, and gas diffusion properties of porous media and mixtures are necessary to optimize the design of porous systems that involve heat and gas transport processes. However, only a limited number of studies provide characterization of soil physical, thermal, and gas diffusion properties and the functional relationships of these properties under varying soil water contents, especially for soil mixtures, complicating optimization efforts. To better understand how mixing controls the physical, thermal, and gas diffusion properties of porous media, a set of laboratory experiments was performed using five volumetric mixtures of coarse‐ and fine‐grained sand particles. For each mixture, the grain‐size distribution (GSD), thermal conductivity, and gas diffusivity were obtained and parameterized using existing and suggested parametric models. Results show that the extended, two‐region Rosin–Rammler particle‐size distribution model proposed in this study could successfully describe the bimodal behavior of the GSD of binary mixtures. Further, the modified Côté and Konrad thermal conductivity model adequately described the thermal conductivity–water saturation relations observed in different mixtures. The proposed simple soil‐gas diffusivity descriptive model parameterized the upper limit, average, and lower limit behavior in gas diffusivity–air content relations in apparently texture‐invariant gas diffusivity data. Results further show a close analogy between gas diffusivity and thermal conductivity and their variation with saturation across different binary mixtures. Overall, the results of the study provide useful numerical insight into the physical, thermal, and gas transport characteristics of binary mixtures, with wide implications for future engineering and research applications that involve multicomponent porous systems.

Deepagoda, T. K. K. Chamindu↗

Developing a High Thermal Conductivity Fuel with Silicon Carbide Additives

The objective of this research is to increase the thermal conductivity of uranium oxide (UO 2 ) without significantly impacting its neutronic properties. The concept is to incorporate another high thermal conductivity material, silicon carbide (SiC), in the form of whiskers or from nanoparticles of SiC and a SiC polymeric precursor into UO 2 . This is expected to form a percolation pathway lattice for conductive heat transfer out of the fuel pellet. The thermal conductivity of SiC would control the overall fuel pellet thermal conductivity. The challenge is to show the effectiveness of a low temperature sintering process, because of a UO 2 -SiC reaction at 1,377°C, a temperature far below the normal sintering temperature. Researchers will study three strategies to overcome the processing difficulties associated with pore clogging and the chemical reaction of SiC and UO 2 at temperatures above 1,300°C:

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Impact Of Standing Water On Saltstone Placement II - Hydraulic Conductivity Data

The amount of water present during placement and subsequent curing of saltstone has the potential to impact several properties important for grout quality. An active drain water system can remove residual standing water and expose the surface of the placed saltstone to air. Oxidation of the saltstone may result in an increase in the leachability of redox sensitive elements. A dry surface can lead to cracking, causing an increase in hydraulic conductivity. An inactive drain water system can allow standing water that generates unnecessary hydrostatic head on the vault walls. Standing water that cannot be removed via the drain system will be available for potential incorporation into subsequent grout placements. The objective of this work is to study the impact of standing water on grout quality pertaining to disposal units. A series of saltstone mixes was prepared and cured at ambient temperature to evaluate the impact of standing water on saltstone placement. The samples were managed to control drying effects on leachability by either exposing or capping the samples. The water to premix ratio was varied to represent a range of processing conditions. Samples were analyzed for density, leachability, and hydraulic conductivity. Report SRNL-STI-2012-00546 was issued detailing the experimental procedure, results, and conclusions related to density and leachability. In the previous report, it was concluded that: density tends to increase toward the bottom of the samples. This effect is pronounced with excess bleed water; drying of the saltstone during curing leads to decreased Leachability Index (more leaching) for potassium, sodium, rhenium, nitrite, and nitrate; there is no noticeable effect on saltstone oxidation/leachability by changing the water to premix ratio (over the range studied), or by pouring into standing water (when tested up to 10 volume percent). The hydraulic conductivity data presented in this report show that samples cured exposed to the atmosphere had about three orders of magnitude higher hydraulic conductivity than any of the other samples. Considering these data, along with the results presented in the previous report, leads to the conclusion that small changes in water to premix ratio and the inclusion of up to 10 volume percent standing water should not be expected to have a detrimental effect on saltstone grout quality. The hydraulic conductivity results further demonstrate that curing in a moist environment is critical to maintaining saltstone quality.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A molecular dynamics study of anisotropy and the effect of Xe on UO 2 thermal conductivity

In this report we first investigate the effect of Xe on UO 2 thermal conductivity via molecular dynamics simulations. This property is studied both as function of temperature and for different concentrations and configurations of Xe atoms (randomly dispersed and in gas bubbles). The largest decrease of the thermal conductivity is obtained for randomly distributed Xe atoms, which is due to high defect scattering and thus decreasing phonon mean free path. Second we demonstrate several different manifestations of anisotropic UO 2 thermal conductivity, including discontinuities between the conductivity of bulk UO 2 separated by asymmetric grain boundaries and variations of the conductivity along different crystallographic directions in single crystals of UO 2 . These results are validated against recent experiments on UO 2 single crystals.

36 MATERIALS SCIENCE↗

Novel Transparent Phosphor Conversion Matrix with High Thermal Conductivity for Next Generation Phosphor-Converted LED-based Solid State Lighting

The low thermal conductivity of state-of-the-art polymer encapsulants (k ~ 0.15 Wm-1K-1) limits the efficiency and power density of current phosphor conversion light emitting diodes (pc-LEDs). The technical objective of this project was to demonstrate synthesis and processing schemes for the fabrication of polymer hybrid encapsulants with a thermal conductivity exceeding k = 0.4 Wm-1K-1 for LED applications. The ‘hybrid polymer’ approach encompasses the dispersion of high thermal conductivity particle fillers (zinc oxide, ZnO as well as the alpha-polymorph of alumina, Al2O3) within a polysiloxane matrix (poly(dimethylsiloxane), PDMS as well as poly(phenyl methyl siloxane), PPMS) to increase the thermal conductivity while maintaining optical transparency and photothermal stability at levels consistent with LED applications. To accomplish this goal, a novel synthesis method for the fabrication of nanosized ZnO particles was developed and a novel surface chemistry was established to modify the surface of zinc oxide particle fillers and thus to enable their dispersion in poly(dimethyl siloxane) (PDMS) matrix polymers. Molecular dynamics and Mie simulations were used to optimize ligand structure and to enable the concurrent mixing of particles in PDMS/PPMS embedding media while also minimizing the thermal boundary resistance as well as optical scattering of particle fillers. Using this approach the synthesis of PDMS/ZnO hybrid encapsulants exhibiting a thermal conductivity of 0.64 Wm-1K-1 and optical transparency > 0.7 mm-1 was demonstrated. A forming process based on micromolding was developed to demonstrate the forming of particle filled PDMS into film and lens shapes. Photothermal stability testing revealed stability of the materials for approximately 4000 min when exposed to blue light LED (450 nm, 30 W/cm2). One postgraduate and seven graduate students were supported by the project. The research performed within this project led to fifteen publications in peer-reviewed journals and one patent application. The grant stimulated a multi-investigator research collaborations among seven investigators at Carnegie Mellon University to address the challenge of encapsulants in pc-LED applications. The grant also catalyzed the future collaboration between researchers at Carnegie Mellon University and OSRAM Sylvania to address challenges associated with the use if polymers in LED applications.

36 MATERIALS SCIENCE↗

Radial Thermal Conductivity Measurement for SiC Composite Tubes

Thermal conductivity is a key property for design and performance assessment of silicon carbide composite (SiC/SiC) cladding that is being developed for accident-tolerant fuel to be used in light water reactors. The thermal conductivity of SiC plate has previously been studied, but it was unknown whether it would be different for tubular SiC. The purpose of this report is to provide the thermal conductivity of prototypic SiC composite tubes under temperatures ranging from ~25°C to ~300°C. Both nonirradiated and neutron-irradiated specimens were evaluated. Thermal diffusivity of curved coupons was measured by a laser flash method. First, the effect of the specimen geometry on thermal diffusivity was investigated using a glass ceramic with known thermal diffusivity. The results showed an insignificant impact of the specimen geometry on the thermal diffusivity in the case of a curvature radius of ~4 mm. Subsequently, nonirradiated and neutron-irradiated SiC composite coupons with the same geometry as the glass ceramic specimens were evaluated. Thermal conductivity was also obtained using additional data for density and specific heat capacity. Equations were written to express the temperature-dependent thermal conductivities of the nonirradiated and irradiated SiC composite tubes.

36 MATERIALS SCIENCE↗

Design and Characterization of High Thermal Conductivity Pipes from Roll-to- Roll Processed Hybrid Copper-Polymer Strips for Waste Heat Recovery

Metal based heat exchangers targeting low temperature (<150°C) waste heat recovery (WHR) face high maintenance and material costs [1] that result in long payback periods (>1 year). Low-cost polymer pipes suffer from poor thermal conductivity (~0.2 W/m.K), and thus a low overall heat transfer coefficient. Previous reports demonstrated thermal conductivity enhancement in polymers through systematic molecular alignment [2, 3, 4], or by metal micro-particle inclusions [5]. However, these approaches suffer from scalability issues for WHR heat exchangers in terms of cost [1, 3], and thermomechanical considerations [6, 7]. In this work, we propose hybrid metal-polymer strips that are strategically designed to enhance thermal conductivity by cladding copper around polymer strips. The polymer strips with copper-clad edges are wound helically to form the pipes for a heat exchanger. Through numerical simulations, we optimize the copper-polymer strip layouts to achieve high wall thermal conductivity (k > 1 W/m.K) and also have low volume fraction of copper (<70%) for the composite pipes. In copper-polymer composite heat exchangers, the bottlenecks for heat transfer are the thermal interfacial resistances of copper-copper and copper-polymer joints. We experimentally measured interfacial resistances to be ~1x10 -5 K.m 2 /W and ~4x10 -5 K.m 2 /W for copper-copper and copper-polymer joints, respectively. Using the measured interfacial resistances, we further optimized the design of the hybrid pipes to find high thermal conductivity (> 1 W/m.K) designs. We predict up to ~20 % enhancement in overall heat transfer relative to an all polymer (k = 0.2 W/m.K) heat exchanger system. Using a cohesive zone modelling (CZM) for predicting delamination at the weld joints, we find that our hybrid pipes can have operating internal pressures > 200 psi. The optimized designs of hybrid metal-polymer pipes provide a scalable and cost- effective means for harvesting waste heat from low temperature sources. Thekdi, A., and Nimbalkar, S. Oak Ridge National Lab (2014). Shen, Sheng, et al. Nature nanotechnology 5.4 (2010). Xu, Yanfei, et al. Science advances 4.3 (2018). Smith et al. ACS nano, 9(2), (2015). Sofian, N.M., et al., Journal of Thermoplastic Composite Materials (2001). Aymonier et al. Chemistry of Materials, 15(25), (2003). Tavman, I.H., Journal of Applied Polymer Science, 62(12), (1996).

C Rajagopal, Manjunath↗

Superionic conduction using ion aggregates

Project objective: Engineer solid polymeric electrolytes with an optimized, self-assembled, ion network that conducts independently of polymer segmental dynamics. The goal of this project is to engineer an optimized, self-assembled ion aggregate network, by which we can incorporate an aggregate assisted, collective, superionic conduction paradigm into polymeric electrolytes. We do not seek to improve conductivity, although this is a likely result of our approach, but to propose systems in which collective motion is the main conduction mechanism. We believe that once such materials are identified, they will quickly become a subject of research in the solid polymer electrolyte community. With this in mind, we pursue three design strategies: increase ion content in PEG single ion conductors, use mixed anions (including divalent ions as crosslinkers), and introduce swelled polyanion/polycation complexes as a potential ion conducting material.

36 MATERIALS SCIENCE↗

Carbon Fiber Reinforced Plastic with Substantially Improved Through-plane Thermal Conductivity

Thermal conductivity of carbon fiber support structures that also serve as cooling substrates is of increasing importance for high energy physics detectors. One of the shortcomings of current carbon fiber laminates is that they exhibit excellent thermal conductivity of order several hundred W/(m*K) along the fiber direction, whereas the through plane thermal conductivity perpendicular to the fibers is orders of magnitude lower, and at about 1 W/(m*K) more in the range of thermal insulators. This proposal aims to significantly improve the through plane thermal conductivity, by at least a factor five, changing CFRP from being a thermal insulator to a thermal conductor in the through plane direction. Between June 2021 and December 2022, a total of 36 carbon fiber laminate test samples and two carbon loaded epoxy test samples were manufactured and analyzed for thermal performance. Unfortunately, the promising results obtained with a similar sample manufactured in 2017 were not reproduced. We believe this to be mainly due the excessive age of the carbon fiber prepreg material used for this SBIR - the same material batch, produced in 2015, was used in 2017 and in 2021/2022, i.e. the material was seven years old when the final samples were produced - , and to a lesser degree to the difference in pressure attainable with the 2017 and 2021/2022 laminate curing setups. While disappointing, the results are not completely discouraging, since for the samples with the highest compression the through-plane thermal conductivities plotted as a function of per-ply thickness extrapolate well to the data point from the 2017 sample.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Industrial Energy Audit Guidebook: Guidelines for Conducting an Energy Audit in Industrial Facilities

Various studies in different countries have shown that significant energy-efficiency improvement opportunities exist in the industrial sector, many of which are cost-effective. These energy-efficiency options include both cross-cutting as well as sector-specific measures. However, industrial plants are not always aware of energy-efficiency improvement potentials. Conducting an energy audit is one of the first steps in identifying these potentials. Even so, many plants do not have the capacity to conduct an effective energy audit. In some countries, government policies and programs aim to assist industry to improve competitiveness through increased energy efficiency. However, usually only limited technical and financial resources for improving energy efficiency are available, especially for small and medium-sized enterprises. Information on energy auditing and practices should, therefore, be prepared and disseminated to industrial plants. This guidebook provides guidelines for energy auditors regarding the key elements for preparing for an energy audit, conducting an inventory and measuring energy use, analyzing energy bills, benchmarking, analyzing energy use patterns, identifying energy-efficiency opportunities, conducting cost-benefit analysis, preparing energy audit reports, and undertaking post-audit activities. The purpose of this guidebook is to assist energy auditors and engineers in the plant to conduct a well-structured and effective energy audit.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Replacing Metal-Based Lightning Strike Protection Layer of CFRPS by 3D Printed Electronically Conductive Polymer Layer

Electrically conductive adhesive layers were deposited on top of aerospace grade carbon fiber reinforced plastic (CFRP) panels using a small-scale 3D printer. Polylactic acid (PLA) filaments with copper filler (CU-PLA) and graphene filler (GO-PLA) were used to print around 0.7 mm thick electrically conductive layer on top of CFRP panels. 3D printed polymeric layers were tested for their effectiveness as a lightning strike protection (LSP) material by subjected to a simulated lightning strike. A painted, electrically non-conductive unprotected panel was also tested for comparison. In the case of the CU-PLA protected sample, a high electrical conductivity proved to be useful in fast dissipation of the lightning current. Fast current dissipation helped to reduce the resistive heating after a lightning strike. Thermography and high-speed camera analysis were employed to study the heat generation and current dissipation during the lightning strike. These results established that a useful Faraday Cage was applied via additive manufacturing successfully. This work shows the successful application of 3D printing for producing LSP technologies, with future work aimed at investigating optimal printable electrically conductive thermoset material candidates.

Kumar, Vipin↗