SEARCH · Engineering Papers

Results for “COMPRESSION STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Electrostatic potential jump across fast-mode collisionless shocks

The electrostatic potential jump across fast-mode collisionless shocks is examined by comparing published observations, hybrid simulations, and a simple model, in order to better characterize its dependence on the various shock parameters. In all three, it is assumed that the electrons can be described by an isotropic power-law equation of state. The observations show that the cross-shock potential jump correlates well with the shock strength but shows very little correlation with other shock parameters. Assuming that the electrons obey an isotropic power law equation of state, the correlation of the potential jump with the shock strength follows naturally from the increased shock compression and an apparent dependence of the power law exponent on the Mach number which the observations indicate. It is found that including a Mach number dependence for the power law exponent in the electron equation of state in the simple model produces a potential jump which better fits the observations. On the basis of the simulation results and theoretical estimates of the cross-shock potential, it is discussed how the cross-shock potential might be expected to depend on the other shock parameters.

Mandt, M. E.↗

NASA NTRS1995

Effects of preform architecture on modulus and strength of 2-D triaxially braided textile composites

Laminates formed using braided fibrous preforms have been extensively investigated during the course of the past few years as alternatives to unidirectional prepreg tape systems. This paper focused on one aspect of that work. It defined the role of the fibrous preform architecture in controlling a laminate's mechanical properties. The presentation was divided into four sections as the outline listed above illustrates. The presentation began with a brief introduction which defined the objectives of the study and detailed the materials studied. This was followed by a review of empirical test results. The materials' moduli and strengths were measured in both tension and compression. Their shear moduli were also experimentally determined. The review of the empirical data comprised the bulk of the presentation. A comparison of the experimental data to results predicted analytically was then presented. The presentation concluded with a few summary remarks. The specimens studied in this investigation featured 2-D triaxially braided AS4 graphite fiber preforms impregnated with Shell 1895 epoxy resin.

Masters, John E.↗

NASA NTRS2000

Validated Feasibility Study of Integrally Stiffened Metallic Fuselage Panels for Reducing Manufacturing Costs

The continual need to reduce airframe cost and the emergence of high speed machining and other manufacturing technologies has brought about a renewed interest in large-scale integral structures for aircraft applications. Applications have been inhibited, however, because of the need to demonstrate damage tolerance, and by cost and manufacturing risks associated with the size and complexity of the parts. The Integral Airframe Structures (IAS) Program identified a feasible integrally stiffened fuselage concept and evaluated performance and manufacturing cost compared to conventional designs. An integral skin/stiffener concept was produced both by plate hog-out and near-net extrusion. Alloys evaluated included 7050-T7451 plate, 7050-T74511 extrusion, 6013-T6511 extrusion, and 7475-T7351 plate. Mechanical properties, structural details, and joint performance were evaluated as well as repair, static compression, and two-bay crack residual strength panels. Crack turning behavior was characterized through panel tests and improved methods for predicting crack turning were developed. Manufacturing cost was evaluated using COSTRAN. A hybrid design, made from high-speed machined extruded frames that are mechanically fastened to high-speed machined plate skin/stringer panels, was identified as the most cost-effective manufacturing solution. Recurring labor and material costs of the hybrid design are up to 61 percent less than the current technology baseline.

Pettit, R. G.↗

NASA NTRS2000

Integral Airframe Structures (IAS): Validated Feasibility Study of Integrally Stiffened Metallic Fuselage Panels for Reducing Manufacturing Costs

The Integral Airframe Structures (IAS) program investigated the feasibility of using "integrally stiffened" construction for commercial transport fuselage structure. The objective of the program was to demonstrate structural performance and weight equal to current "built-up" structure with lower manufacturing cost. Testing evaluated mechanical properties, structural details, joint performance, repair, static compression, and two-bay crack residual strength panels. Alloys evaluated included 7050-T7451 plate, 7050-T74511 extrusion, 6013-T6511x extrusion, and 7475-T7351 plate. Structural performance was evaluated with a large 7475-T7351 pressure test that included the arrest of a two-bay longitudinal crack, and a measure of residual strength for a two-bay crack centered on a broken frame. Analysis predictions for the two-bay longitudinal crack panel correlated well with the test results. Analysis activity conducted by the IAS team strongly indicates that current analysis tools predict integral structural behavior as accurately as built-up structure. The cost study results indicated that, compared to built-up fabrication methods, high-speed machining structure from aluminum plate would yield a recurring cost savings of 61%. Part count dropped from 78 individual parts on a baseline panel to just 7 parts for machined IAS structure.

Munroe, J.↗

NASA NTRS2000

Theta-Pinch Thruster for Piloted Deep Space Exploration

A new high-power propulsion concept that combines a rapidly pulsed theta-pinch discharge with upstream particle reflection by a magnetic mirror was evaluated under a Phase 1 grant awarded through the NASA Institute for Advanced Concepts. Analytic and numerical models were developed to predict the performance of a theta-pinch thruster operated over a wide range of initial gas pressures and discharge periods. The models indicate that a 1 m radius, 10 m long thruster operated with hydrogen propellant could provide impulse-bits ranging from 1 N-s to 330 N-s with specific impulse values of 7,500 s to 2,500 s, respectively. A pulsed magnetic field strength of 2 T is required to compress and heat the preionized hydrogen over a 10(exp -3) second discharge period, with about 60% of the heated plasma exiting the chamber each period to produce thrust. The unoptimized thruster efficiency is low, peaking at approximately 16% for an initial hydrogen chamber pressure of 100 Torr. The specific impulse and impulse-bit at this operating condition are 3,500 s and 90 N-s, respectively, and the required discharge energy is approximately 9x10(exp 6) J. For a pulse repetition rate of 10 Hz, the engine would produce an average thrust of 900 N at 3,500 s specific impulse. Combined with the electrodeless nature of the device, these performance parameters indicate that theta-pinch thrusters could provide unique, long-life propulsion systems for piloted deep space mission applications.

LaPointe, Mike R.↗

NASA NTRS2014

Evaluation of RTM370 Polyimide Composites by Resin Film Infusion (RFI)

RTM370 imide oligomer based on 2,3,3',4'-biphenyl dianhydride (a-BPDA), 3,4'-oxydianiline (3,4'-ODA) and terminated with the 4-phenylethynylphthalic (PEPA) endcap has been shown to exhibit a low melt viscosity (10-30 poise) at 280 C with a pot-life of 1-2 h and a high cured glass-transition temperature (Tg) of 370 C. RTM370 resin has been successfully infused into fiberglass-stitched T650-35 carbon-fabric preforms (ranged from 3- to 6-mm thick) by resin film infusion (RFI). The resulting composite panels were inspected by ultrasonic C-scan and by photomicrographs before and after post-curing as a quality control. Mechanical tests such as unnotched compression (UNC), open-hole compression (OHC), and short-beam shear strength (SBS) at ambient and elevated temperatures were performed before and after isothermal aging at 288 C for 1000 h to assess high-temperature performance. Thermal cycling of RTM370 stitched composites was also conducted from -54 C to 288 C for up to 1600 cycles to evaluate the microcrack resistance of RTM370 polyimide composites fabricated by RFI.

Polyimide↗

DOE OSTI2023

A novel additive manufacturing compression overmolding process for hybrid metal polymer composite structures

Metal polymer composites combining low density, high strength composites with highly ductile and tough metals have gained traction over the last few decades as lightweight and high-performance materials for industrial applications. However, the mechanical properties are limited by the interfacial bonding strength between metals and polymers achieved through adhesives, welding, and surface treatment processes. In this paper, a novel manufacturing process combining additive manufacturing and compression molding to obtain hybrid metal polymer composites with enhanced mechanical properties is presented. Additive manufacturing enabled deposition of polymeric material with fibers in a predetermined pattern to form tailored charge or preform for compression molding. Here, a grade 300 maraging steel triangular lattice is first fabricated using AddUp FormUp350 laser powder bed system and compression overmolded with additively manufactured long carbon fiber-reinforced polyamide-6,6 (40% wt. CF/PA66) preform. The fabricated hybrid metal polymer composites showed high stiffness and tensile strength. The stiffness and failure characteristics determined from the uniaxial tensile tests were correlated to a finite element model within 20% deviation. Fractographic analyses was performed using microscopy to investigate failure mechanisms of the hybrid structures.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Experimental investigation of heat treatments on the mechanical performance of grade 300 maraging steel strut-based lattices

Lightweight and strong components are essential for reducing energy consumption and enhancing efficiency. Lattice structures are one such geometry utilized to achieve weight reduction. This study investigates the mechanical properties of various lattice structures fabricated from Maraging Steel (EOS MS1) using the Direct Metal Laser Sintering (DMLS) method. The samples include three distinct cellular geometries: body-centered cubic (BCC), face-centered cubic (FCC), and octet truss configurations, which are subjected to tensile and compressive tests. The primary goal of this research is to evaluate the impact of heat treatment on the mechanical properties of cellular architecture under tensile and compressive loading conditions. Destructive, nondestructive testing, and simulation results were also obtained from different heat treatment processes. It was found that the age-hardened specimens performed the best overall in terms of ultimate tensile/compressive strength and elongation. The top-performing topologies in compression and tension were found to be the octet structure, as they were able to withstand the most loading and straining when compared to the other specimens.

Engineering↗

NASA NTRS1976

Buckling behavior and structural efficiency of open-section stiffened composite compression panels

Several experiments with J- and blade-stiffened graphite/epoxy panels were conducted to obtain insight into how well experimental data could be correlated with analysis for the buckling behavior of open-section stiffened composite compression panels. Although some nonlinear behavior was observed during the experiments, adequate correlation with analysis was obtained to justify the use of linear, thin-plate buckling analysis in a minimum-weight design synthesis program for J- and blade-configurations. Results from two design studies using this program are presented. In the first study the minimum weights of Jand blade-configurations for two different material systems (graphite/epoxy and aluminum) are determined subject to buckling and strength constraints for a wide range of the compressive load index. In the second study the minimum weights required for graphite/epoxy blade-stiffened panels to satisfy additional stiffness constraints typical of medium-size commercial aircraft wing structures are determined. Both minimum-weight studies indicate that graphite/epoxy open-section stiffened panels can be designed so that weight savings of 30 to 50% are possible compared with the most efficient aluminum designs.

Williams, J. G.↗

NASA NTRS1993

Compressive and shear buckling analysis of metal matrix composite sandwich panels under different thermal environments

Combined inplane compressive and shear buckling analysis was conducted on flat rectangular sandwich panels using the Raleigh-Ritz minimum energy method with a consideration of transverse shear effect of the sandwich core. The sandwich panels were fabricated with titanium honeycomb core and laminated metal matrix composite face sheets. The results show that slightly slender (along unidirectional compressive loading axis) rectangular sandwich panels have the most desirable stiffness-to-weight ratios for aerospace structural applications; the degradation of buckling strength of sandwich panels with rising temperature is faster in shear than in compression; and the fiber orientation of the face sheets for optimum combined-load buckling strength of sandwich panels is a strong function of both loading condition and panel aspect ratio. Under the same specific weight and panel aspect ratio, a sandwich panel with metal matrix composite face sheets has much higher buckling strength than one having monolithic face sheets.

Ko, William L.↗

NASA NTRS1993

Compressive and shear buckling analysis of metal matrix composite sandwich panels under different thermal environments

Ko, William L.↗

DOE OSTI2023

Study of The Compression of an Imploding Plasma and the Magnetic- Field Flux Using Advanced, Non-Intrusive, Spectroscopic Techniques

The main motivation of the project was to measure the magnetic field in pulsed power driven plasma compression using advanced non-intrusive spectroscopic techniques. The strength of the project is that it encompasses a combination of laboratory experiments with diagnostics for both the magnetic field and plasma properties and computational modeling. The following issues were addressed: (1) Plasma and magnetic field dynamics, (2) Field compression and diffusion, (3) Energy balance in the system, (4) Onset of instabilities, and (5) Correlation of the plasma and field evolutions with the initial conditions. The unique feature of the research was the use of advanced spectroscopy to measure both the magnetic field and various plasma properties in multiple locations using both side-on and end-on views, simultaneously. The experimental system allowed for imploding different gas mixtures (which facilitated local measurements) and for flexibility in modifying the initial conditions. Two current generators were used with significantly different current rise times (200 ns and 1.6 µs) but at the same current level of 400 kA. The slower pulsed power generator (at rise time 1.6 µs) was based at the Weizmann Institute of Science (WIS) and imploded plasma into which an axial magnetic field (up to 1 T) was initially embedded. The faster current rise time generator (at rise time 200 ns) based at University of California San Diego (UCSD) was used for plasma parameter studies initially, with collaborative efforts we successfully implemented the advanced spectroscopy techniques at UC San Diego. One graduate student (Nick Aybar) and a postdoctoral scholar (Maylis Dozeries) were trained. They both are based at the Lawrence Livermore National Laboratory now.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2000

Design, Fabrication, and Testing of Ceramic Joints for High Temperature SiC/SiC Composites

Various issues associated with the design and mechanical evaluation of joints of ceramic matrix composites are discussed. The specific case of an affordable, robust ceramic joining technology (ARCJoinT) to join silicon carbide (CG-Nicalon(sup TM)) fiber-reinforced-chemically vapor infiltrated (CVI) silicon carbide matrix composites is addressed. Experimental results are presented for the time and temperature dependence of the shear strength of these joints in air up to 1200 C. From compression testing of double-notched joint specimens with a notch separation of 4 mm, it was found that the apparent shear strength of the joints decreased from 92 MPa at room temperature to 71 MPa at 1200 C. From shear stress-rupture testing in air at 1200 C it was found that the shear strength of the joints decreased rapidly with time from an initial shear strength of 71 to 17.5 MPa after 14.3 hr. The implications of these results in relation to the expected long-term service life of these joints in applications at elevated temperatures are discussed.

Singh, Mrityunjay↗

DOE OSTI2017

Dynamic Uniaxial Compression of HSLA-65 Steel at Elevated Temperatures

Here, the dynamic response of a high-strength, low alloy Grade 65 (HSLA-65) steel, used by the United States Navy for ship hull construction, is investigated under dynamic uniaxial compression at temperatures ranging from room temperature to 1000 °C using a novel elevated temperature split-Hopkinson pressure bar. These experiments are designed to probe the dynamic response of HSLA-65 steel in its single α-ferrite phase, mixed α + γ-austenite phase, and the single γ-austenite phase, as a function of temperature. The investigation is conducted at two different average strain rates—1450 and 2100/s. The experimental results indicate that at test temperatures in the range from room temperature to lower than 600 °C, i.e. prior to the development of the mixed α + γ phase, a net softening in flow strength is observed at all levels of plastic strain with increase in test temperatures. As the test temperatures are increased, the rate of this strain softening with temperature is observed to decrease, and at 600 °C the trend reverses itself resulting in an increase in flow stress at all strains tested. This increase in flow stress is understood be due to dynamic strain aging, where solute atoms play a distinctive role in hindering dislocation motion. At 800 °C, a (sharp) drop in the flow stress, equivalent to one-half of its value at room temperature, is observed. As the test temperature are increased to 900 and 1000 °C, further drop in flow stress are observed at all plastic strain levels. In addition, strain hardening in flow stress is observed at all test temperatures up to 600 °C; beyond 800 °C the rate of strain hardening isobserved to decrease, with strain softening becoming dominant at temperatures of 900 °C and higher. Moreover, comparing the high strain rate stress versus strain data gathered on HSLA 65 in the current investigation with those available in the literature at quasi-static strain rates, strain-rate hardening can be inferred. The flow stress increases from 700 MPa at 8 × 10 -4 /s to 950 MPa at 1450/s and then to 1000 MPa at 2100/s at a strain of 0.1. Finally, optical microscopy is used to understand evolution of microstructure in the posttest samples at the various test temperatures employed in the present study.

36 MATERIALS SCIENCE↗

NASA NTRS1987

Bearing-bypass loading on bolted composite joints

The effects of simultaneous bearing and bypass loading on a graphite-epoxy (T300/5208) laminate were investigated. Onset damage and ultimate strengths were determined for each test case. A finite element stress analysis was conducted for each test case. The computed local stresses were used with appropriate failure criteria to analyze the observed failure modes and strengths. An unexpected interaction of the effect of the bypass and bearing loads was found for the onset of compression reacted bearing damage. The interaction was caused by a decrease in the bolt-hole contact arc and a corresponding increase in the severity of the bearing loads. The amount of bolt-hole contact had a significant effect on local stresses and, thus, on the calculated damage-onset and ultimate strengths. An offset-compression failure mode was identified for laminate failure under compression bearing-bypass loading.

Crews, J. H., Jr.↗

NASA NTRS1990

Impact damage and residual strength analysis of composite panels with bonded stiffeners

Blade-stiffened, compression-loaded cover panels were designed, manufactured, analyzed, and tested. All panels were fabricated from IM6/1808I interleafed graphite-epoxy. An orthotropic blade stiffener and an orthotropic skin were selected to satisfy the design requirements for an advanced aircraft configuration. All specimens were impact damaged prior to testing. Experimental results were obtained for three- and five-stiffener panels. Analytical results described interlaminar forces caused by impact and predicted specimen residual strength. The analytical results compared reasonably with the experimental results for residual strength of the specimens.

Madan, Ram C.↗

DOE OSTI2022

A compact x-ray diffraction system for dynamic compression experiments on pulsed-power generators

Pulsed-power generators can produce well-controlled continuous ramp compression of condensed matter for high-pressure equation-of-state studies using the magnetic loading technique. X-ray diffraction (XRD) data from dynamically compressed samples provide direct measurements of the elastic compression of the crystal lattice, onset of plastic flow, strength–strain rate dependence, structural phase transitions, and density of crystal defects, such as dislocations. Here, we present a cost-effective, compact, pulsed x-ray source for XRD measurements on pulsed-power-driven ramp-loaded samples. This combination of magnetically driven ramp compression of materials with a single, short-pulse XRD diagnostic will be a powerful capability for the dynamic materials’ community to investigate in situ dynamic phase transitions critical to equation of states. Finally, we present results using this new diagnostic to evaluate lattice compression in Zr and Al and to capture signatures of phase transitions in CdS.

47 OTHER INSTRUMENTATION↗

DOE OSTI2020

Plastic anisotropy and tension-compression asymmetry in nanotwinned Al–Fe alloys: An in-situ micromechanical investigation

The mechanical strength of commercial Al alloys rarely exceeds 700 MP. Recent studies show that nanotwinned Al alloys and other nanocolumnar metals exhibit superb mechanical behaviors but a discrepancy between tensile and hardness measurements often emerges and their orientation dependent deformation mechanisms remain unclear. Here, we inspect the mechanical response of columnar nanotwinned Al–Fe alloys with emphasis on response of grain boundaries to in-situ tension and compression tests along both in-plane and out-of-plane directions inside a scanning electron microscope. Our studies reveal ultra-high out-of-plane tensile and compressive stress, exceeding 1.8 GPa, and an in-plane tensile and compressive stress of 1.1 and 1.6 GPa, respectively. Post-mortem TEM analyses were performed to elucidate the orientation-dependent plastic anisotropy and tension-compression asymmetry in columnar nanotwinned Al–Fe alloys. This study provides an important forward step towards the understanding of deformation mechanisms in high-strength nanotwinned Al alloys and metals with nanocolumnar or non-equiaxed grains.

36 MATERIALS SCIENCE↗