Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BRITTLENESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,351 records · Page 75

Effect of deposition rate on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by laser engineered net shaping

Laser engineered net shaping (LENS) is an additive manufacturing technique for fabricating and repairing metallic components. However, the relationships between its process parameters and the resulting mechanical properties of alloys such as 17-4 precipitation-hardening (PH) stainless steel require further investigation to enable reliable application. This study examines the specific effect of LENS deposition rate on the microstructure and mechanical properties of 17-4 PH stainless steel. Specimens were fabricated at two different deposition rates (8.47 and 9.31 mm s−1), subjected to subsequent solution and H900 aging treatment, and then evaluated via tensile testing, hardness measurements, and microscopy. A higher deposition rate results in a finer grain structure but increased porosity, leading to greater ultimate tensile strength (∼1294 MPa) yet lower ductility (strain at failure ∼5.8%) compared to the slower deposition rate (∼1266 MPa, ∼9.0% strain). Hardness follows the same trend as tensile strength. Tensile fracture surfaces for both conditions exhibited a mixed mode of ductile dimples and brittle quasi-cleavage regions, with chromium/silicon oxide particles identified within dimples. Complementary finite element modeling indicates that small void fractions primarily reduce ductility by enhancing localized plasticity, with only a marginal decrease in tensile strength. These integrated experimental and numerical results elucidate the mechanical properties linked to deposition rate, providing insight into tailoring LENS processes to achieve desired properties of 17-4 PH stainless steel.

17-4 PH stainlesssteel↗

Irradiation damage concurrent challenges with RAFM and ODS steels for fusion reactor first-wall/blanket: a review

Reduced activation ferritic martensitic (RAFM) and oxide dispersion strengthened (ODS) steels are the most promising candidates for fusion first-wall/blanket (FW/B) structures. The performance of these steels will deteriorate during service due to neutron damage and transmutation-induced gases, such as helium/hydrogen, at elevated operating temperatures. Here, after highlighting the operating conditions of fusion reactor concepts and a brief overview, the main irradiation-induced degradation challenges associated with RAFM/ODS steels are discussed. Their long-term degradation scenarios such as (a) low-temperature hardening embrittlement (LTHE)—including dose-temperature dependent yield stress, tensile elongations, necking ductility, test temperature effect on hardening, Charpy impact ductile-to-brittle transition temperature and fracture toughness, (b) intermediate temperature cavity swelling, (c) the effect of helium on LTHE and cavity swelling, (d) irradiation creep and (e) tritium management issues are reviewed. The potential causes of LTHE are discussed, which highlights the need for advanced characterisation techniques. The mechanical properties, including the tensile/Charpy impact of RAFM and ODS steels, are compared to show that the current generation of ODS steels also suffers from LTHE, and shows irradiation hardening up to high temperatures of ~400 °C–500 °C. To minimise this, future ODS steel development for FW/B-specific application should target materials with a lower Cr concentration (to minimise α'), and minimise other elements that could form embrittling phases under irradiation. RAFM steel-designing activities targeting improvements in creep and LTHE are reviewed. The need to better understand the synergistic effects of helium on the thermo-mechanical properties in the entire temperature range of FW/B is highlighted. Because fusion operating conditions will be complex, including stresses due to the magnetic field, primary loads like coolant pressure, secondary loads from thermal gradients, and due to spatial variation in damage levels and gas production rates, an experimentally validated multiscale modelling approach is suggested as a pathway to future reactor component designing such as for the fusion neutron science facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Artificial neural network potentials for mechanics and fracture dynamics of two-dimensional crystals **

Understanding the mechanics and failure of materials at the nanoscale is critical for their engineering and applications. The accurate atomistic modeling of brittle failure with crack propagation in covalent crystals requires a quantum mechanics-based description of individual bond-breaking events. Artificial neural network potentials (NNPs) have emerged to overcome the traditional, physics-based modeling tradeoff between accuracy and accessible time and length scales. Previous studies have shown successful applications of NNPs for describing the structure and dynamics of molecular systems and amorphous or liquid phases of materials. However, their application to deformation and failure processes in materials is still uncommon. In this study, we discuss the apparent limitations of NNPs for the description of deformation and fracture under loadings and propose a way to generate and select training data for their employment in simulations of deformation and fracture simulations of crystals. We applied the proposed approach to 2D crystalline graphene, utilizing the density-functional tight-binding method for more efficient and extensive data generation in place of density functional theory. Then, we explored how the data selection affects the accuracy of the developed artificial NNPs. It revealed that NNP’s reliability should not only be measured based on the total energy and atomic force comparisons for reference structures but also utilize comparisons for physical properties, e.g. stress–strain curves and geometric deformation. In sharp contrast to popular reactive bond order potentials, our optimized NNP predicts straight crack propagation in graphene along both armchair and zigzag (ZZ) lattice directions, as well as higher fracture toughness of ZZ edge direction. Our study provides significant insight into crack propagation mechanisms on atomic scales and highlights strategies for NNP developments of broader materials.

2D materials↗

Characterization of damage processes in Montney siltstone under triaxial compression using acoustic emission and diagnostic imaging

SUMMARY Crack nucleation and rock failure processes in a fine-grained siltstone (Montney Formation) under triaxial compression are investigated using combined diagnostic techniques, including ultrasonic-wave measurement, acoustic-emission (AE) monitoring, computed tomography (CT) scanning, and thin-section imaging. The sample displays a weak-to-moderate inherent seismic anisotropy and noticeable stress-induced anisotropy prior to failure. No AE event was detected until the applied axial stress reached 95 per cent of the peak value. The signal-to-noise ratio is relatively low, however, and detectable AE events are more diffuse than those observed in highly brittle rocks. The AE locations correlate with a shear fracture zone imaged by CT scanning. AE moment-tensor analysis reveals that events with larger relative magnitudes are characterized by high volumetric (tensile or compressive) components, and the initiation of the failure zone is dominated by combined shear-tensile (ST) failure. Stress inversion of the AE events with high tensile components is in good agreement with the known applied stress. Microscopic imaging of thin sections from the failed sample shows that the failure zone is an en echelon structure consisting of a major fracture with branching micro and minor cracks. This failure mechanism is consistent with a ST source mechanism and is interpreted to be associated with the fine granular structure and mineral composition of Montney siltstone.

Jia, Suzie Q. (ORCID:0000000326496190)↗

Fault geometry and slip distribution of the 2008 M w 7.9 Wenchuan, China earthquake, inferred from GPS and InSAR measurements

We revisit the problem of coseismic rupture of the 2008 M w 7.9 Wenchuan earthquake. Precise determination of the fault structure and slip distribution provides critical information about the mechanical behaviour of the fault system and earthquake rupture. We use all the geodetic data available, craft a more realistic Earth structure and fault model compared to previous studies, and employ a nonlinear inversion scheme to optimally solve for the fault geometry and slip distribution. Compared to a homogeneous elastic half-space model and laterally uniform layered models, adopting separate layered elastic structure models on both sides of the Beichuan fault significantly improved data fitting. Our results reveal that: (1) The Beichuan fault is listric in shape, with near surface fault dip angles increasing from ~36° at the southwest end to ~83° at the northeast end of the rupture. (2) The fault rupture style changes from predominantly thrust at the southwest end to dextral at the northeast end of the fault rupture. (3) Fault slip peaks near the surface for most parts of the fault, with~8.4mthrust and ~5 m dextral slip near Hongkou and ~6 m thrust and ~8.4 m dextral slip near Beichuan, respectively. (4) The peak slips are located around fault geometric complexities, suggesting that earthquake style and rupture propagation were determined by fault zone geometric barriers. Such barriers exist primarily along restraining left stepping discontinuities of the dextralcompressional fault system. (5) The seismic moment released on the fault above 20 km depth is 8.2 × 10 21 N m, corresponding to an M w 7.9 event. The seismic moments released on the local slip concentrations are equivalent to events of M w 7.5 at Yingxiu-Hongkou, M w 7.3 at Beichuan-Pingtong, M w 7.2 near Qingping, M w 7.1 near Qingchuan, and M w 6.7 near Nanba, respectively. (6) The fault geometry and kinematics are consistent with a model in which crustal deformation at the eastern margin of the Tibetan plateau is decoupled by differential motion across a decollement in the mid crust, above which deformation is dominated by brittle reverse faulting and below which deformation occurs by viscous horizontal shortening and vertical thickening.

58 GEOSCIENCES↗

Molecular cloning of the tomato Hairless gene implicates actin dynamics in trichome-mediated defense and mechanical properties of stem tissue

Abstract Trichomes are epidermal structures that provide a first line of defense against arthropod herbivores. The recessive hairless (hl) mutation in tomato (Solanum lycopersicum L.) causes severe distortion of trichomes on all aerial tissues, impairs the accumulation of sesquiterpene and polyphenolic compounds in glandular trichomes, and compromises resistance to the specialist herbivore Manduca sexta. Here, we demonstrate that the tomato Hl gene encodes a subunit (SRA1) of the highly conserved WAVE regulatory complex that controls nucleation of actin filaments in a wide range of eukaryotic cells. The tomato SRA1 gene spans a 42-kb region containing both Solyc11g013280 and Solyc11g013290. The hl mutation corresponds to a complex 3-kb deletion that removes the last exon of the gene. Expression of a wild-type SRA1 cDNA in the hl mutant background restored normal trichome development, accumulation of glandular trichome-derived metabolites, and resistance to insect herbivory. These findings establish a role for SRA1 in the development of tomato trichomes and also implicate the actin-cytoskeleton network in cytosolic control of specialized metabolism for plant defense. We also show that the brittleness of hl mutant stems is associated with altered mechanical and cell morphological properties of stem tissue, and demonstrate that this defect is directly linked to the mutation in SRA1.

59 BASIC BIOLOGICAL SCIENCES↗

Uniaxial tensile mechanical properties from a scratch on ultra-fine grained tungsten

We demonstrate that surface-based mechanical testing can be used to quantify a wide range of mechanical properties determined using traditional uniaxial tension experiments. These include mapping of dynamic stress–strain behaviour, which can be used as a screening tool for uniaxial tensile ductility (uniform elongation), fracture toughness (K C ), which is shown to be in good agreement with reported plane-strain K IC , as well work-hardening exponents (n), activation volumes (V) energies (Q) and strain-rate sensitivity (m) exponents as a function of temperature. Advantages of the surface-based approach are the ability to work with significantly smaller volumes and accommodate processing defects like pores, voids and cracks. These methods are applied to ultra-fine grained tungsten (average grain size of 650 nm), as it is an ideal candidate for alloy development efforts in advanced energy systems. Tungsten is a useful baseline as it exhibits a near-ambient temperature (approx. 200°C) ductile-to-brittle transition temperature (DBTT), enabling validation efforts for the proposed methods, and extraordinary material properties, including the highest melting temperature of any metal and complex temperature and strain-rate dependencies linked to transitions in dislocation mechanisms.

36 MATERIALS SCIENCE↗

In situ observation of fracture processes in high-strength concretes and limestone using high-speed X-ray phase-contrast imaging

The mechanical properties and fracture mechanisms of geomaterials and construction materials such as concrete are reported to be dependent on the loading rates. However, the in situ cracking inside such specimens cannot be visualized using traditional optical imaging methods since the materials are opaque. In this study, the in situ sub-surface failure/damage mechanisms in Cor-Tuf (a reactive powder concrete), a high-strength concrete (HSC) and Indiana limestone under dynamic loading were investigated using high-speed synchrotron X-ray phase-contrast imaging. Dynamic compressive loading was applied using a modified Kolsky bar and fracture images were recorded using a synchronized high-speed synchrotron X-ray imaging set-up. Three-dimensional synchrotron X-ray tomography was also performed to record the microstructure of the specimens before dynamic loading. In the Cor-Tuf and HSC specimens, two different modes of cracking were observed: straight cracking or angular cracking with respect to the direction of loading. In limestone, cracks followed the grain boundaries and voids, ultimately fracturing the specimen. Cracks in HSC were more tortuous than the cracks in Cor-Tuf specimens. The effects of the microstructure on the observed cracking behaviour are discussed. This article is part of the themed issue ‘Experimental testing and modelling of brittle materials at high strain rates’.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Toughening materials: enhancing resistance to fracture

It has been said that ‘God invented plasticity, but the Devil invented fracture!’ Both mechanisms represent the two prime modes of structural failure, respectively, plastic collapse and the rupture/breaking of a component, but the concept of developing materials with enhanced resistance to fracture can be difficult. This is because fracture resistance invariably involves a compromise—between strength and ductility, between strength and toughness—fundamentally leading to a ‘conflict’ between nano-/micro-structural damage and the mechanisms of toughening. Here, we examine the two major classes of such toughening: (i) intrinsic toughening, which occurs ahead of a crack tip and is motivated by plasticity—this is the principal mode of fracture resistance in ductile materials, and (ii) extrinsic toughening, which occurs at, or in the wake of, a crack tip and is associated with crack-tip shielding—this is generally the sole mode of fracture resistance in brittle materials. We briefly examine how these distinct mechanistic processes have been used to toughen synthetic materials—intrinsically in gradient materials and in multiple principal-element metallic alloys with the example of metallic glasses and high-entropy alloys, and extrinsically in ceramics with the example of ceramic-matrix composites—in comparison to Nature which has been especially adept in creating biological/natural materials which are toughened by one or both mechanistic classes, despite often consisting of constituents with meagre mechanical properties. The success of Nature has been driven by its ability to cultivate the development of materials with multiple length-scale hierarchical structures that display ingenious gradients and structural adaptability, a philosophy which we need to emulate and more importantly learn to synthesize to make structural materials of the future with unprecedented combinations of mechanical properties.

36 MATERIALS SCIENCE↗

Low viscosity of solid MgO at high pressures and strain rates measured using the laser-driven Richtmyer-Meshkov instability

Solids are often assumed to behave as viscous fluids under high-strain rates. This behavior has been studied experimentally in metals but largely unexplored in brittle ceramic materials. Here, in this study, we present a technique for measuring the viscosity of MgO using time-resolved velocimetry to track the growth rate of a perturbation caused by the Richtmyer-Meshkov instability at the OMEGA EP laser facility. To interpret the results, we use an in-house Eulerian hydrocode to simulate our experiments and model the plastic deformation of solid MgO as a viscous fluid. Results indicate that MgO has a surprisingly low upper bound to its effective viscosity of ∼10 2 ⁢ Pa s at 175 ± 15⁢ GPa, ∼3500⁢K, and 10 6 −10 7 s −1 strain rate.

Perez, Tyler M. [Johns Hopkins Univ., Baltimore, M↗

Titanium α-ω phase transformation pathway and a predicted metastable structure

A titanium is a highly utilized metal for structural lightweighting and its phases, transformation pathways (transition states), and structures have scientific and industrial importance. Using a proper solid-state nudged elastic band method employing two climbing images combined with density functional theory DFT + U methods for accurate energetics, we detail the pressure-induced α (ductile) to ω (brittle) transformation at the coexistence pressure. We also find two transition states along the minimal-enthalpy path and discover a metastable body-centered orthorhombic structure, with stable phonons, a lower density than the end-point phases, and decreasing stability with increasing pressure.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Strength and deformation of shocked diamond single crystals: Orientation dependence

Understanding and quantifying the strength or elastic limit of diamond single crystals is of considerable scientific and technological importance, and has been a subject of long standing theoretical and experimental interest. To examine the effect of crystalline anisotropy on strength and deformation of shocked diamond single crystals, plate impact experiments were conducted to measure wave profiles at various elastic impact stresses up to ~120 GPa along [110] and [111] crystal orientations. Using laser interferometry, particle velocity histories and shock velocities in the diamond samples were measured and were compared with similar measurements published previously for shock compression along the [100] direction. Wave profiles for all three orientations showed large elastic wave amplitudes followed by time-dependent inelastic deformation. From the measured wave profiles, the elastic limits were determined under well characterized uniaxial strain loading conditions. The measured elastic wave amplitudes for the [110] and [111] orientations were lower for higher elastic impact stress (stress attained for an elastic diamond response), consistent with the result reported previously for [100] diamond. The maximum resolved shear stress (MRSS) on the {111}<110> slip systems was determined for each orientation, revealing significant orientation dependence. The MRSS values for the [100] and [110] orientations (~33 GPa) are 25-30% of theoretical estimates; the MRSS value for the [111] orientation is significantly lower (~23 GPa). Our results demonstrate that the MRSS depends strongly on the stress component normal to the {111} planes or the resolved normal stress (RNS), suggesting that the RNS plays a key role in inhibiting the onset of inelastic deformation. Lower elastic wave amplitudes at higher peak stress and the effect of the RNS are inconsistent with typical dislocation slip mechanisms of inelastic deformation, suggesting instead an inelastic response characteristic of shocked brittle solids. The present results show that the elastic limit (or material strength) of diamond single crystals cannot be described using traditional isotropic approaches, and typical plasticity models cannot be used to describe the inelastic deformation of diamond. Analysis of the measured wave profiles beyond the elastic limit, including characterization of the peak state, requires numerical simulations that incorporate a time-dependent, anisotropic, inelastic deformation response. Development of such a material description for diamond is an important need.

36 MATERIALS SCIENCE↗

Micromechanical Model for Deformation in Solids with Universal Predictions for Stress-Strain Curves and Slip Avalanches

A basic micromechanical model for deformation of solids with only one tuning parameter (weakening {epsilon}) is introduced. The model can reproduce observed stress-strain curves, acoustic emissions and related power spectra, event statistics, and geometrical properties of slip, with a continuous phase transition from brittle to ductile behavior. Exact universal predictions are extracted using mean field theory and renormalization group tools. The results agree with recent experimental observations and simulations of related models for dislocation dynamics, material damage, and earthquake statistics.

36 MATERIALS SCIENCE↗

Fracture Toughness of Metallic Glasses: Annealing-Induced Embrittlement

Quantitative understanding of the fracture toughness of metallic glasses, including the associated ductile-to-brittle (embrittlement) transitions, is not yet available. Here, we use a simple model of plastic deformation in glasses, coupled to an advanced Eulerian level set formulation for solving complex free-boundary problems, to calculate the fracture toughness of metallic glasses as a function of the degree of structural relaxation corresponding to different annealing times near the glass temperature. Finally, our main result indicates the existence of an elastoplastic crack tip instability for sufficiently relaxed glasses, resulting in a marked drop in the toughness, which we interpret as annealing-induced embrittlement transition similar to experimental observations.

36 MATERIALS SCIENCE↗

Critical Scaling of Solid Fragmentation at Quasistatic and Finite Strain Rates

Here, using two-dimensional simulations of sheared, brittle solids, we characterize the resulting fragmentation and explore its underlying critical nature. Under quasistatic loading, a power-law distribution of fragment masses emerges after fracture which grows with increasing strain. With increasing strain rate, the maximum size of a grain decreases and a shallower distribution is produced. We propose a scaling theory for distributions based on a fractal scaling of the largest mass with system size in the quasistatic limit or with a correlation length that diverges as a power of rate in the finite-rate limit. Critical exponents are measured using finite-size scaling techniques.

36 MATERIALS SCIENCE↗

Intrinsic ductility of random substitutional alloys from nonlinear elasticity theory

A method suitable for computing the ideal strength of random substitutional alloys is introduced. The method relies on nonlinear continuum elasticity theory and allows for the high-throughput computation of ideal strength. The method also allows for the high-throughput computation of an intrinsic ductility parameter defined for a given applied stress state as the ratio of the strain associated with the cleavage instability to the strain associated with the first shear instability. The intrinsic ductility parameter is shown to correlate well with the measured elongations to failure for elemental body-centered-cubic and hexagonal close-packed metals. Application to four high-entropy alloys indicates that the intrinsic ductility parameter describes their experimental compressions to failure well. The method is used to argue that the brittle refractory high-entropy alloy Ta-Nb-V-W-Mo could be made much more ductile through replacement of Mo with Nb. Finally, the potential for the high-throughput optimization of high entropy and chemically complex alloys is discussed.

36 MATERIALS SCIENCE↗

Predicting the location of shear band initiation in a metallic glass

We report atomistic simulation results which indicate that the location of shear banding in a metallic glass (MG) can be ascertained with reasonably high accuracy solely from the undeformed static structure. Correlation is observed between the location of the initiation of shear bands in a simulated MG and the initial distribution of the density of fertile sites (DFS) for stress-driven shear transformations identified a priori based on a deep learning model devised in our recent work. In addition, we demonstrated that one can judge whether a glass is brittle or ductile solely based upon its initial DFS distribution. These validate that shear bands in MG arise from nonlinear instabilities and that the as-quenched glass structure contains inhomogeneities that influence these instabilities. In this study, we also reveal an important subtlety regarding the nondeterministic nature of athermal quasistatic shear simulations.

36 MATERIALS SCIENCE↗

A lathe system for micrometre-sized cylindrical sample preparation at room and cryogenic temperatures

A simple two-spindle based lathe system for the preparation of cylindrical samples intended for X-ray tomography is presented. The setup can operate at room temperature as well as under cryogenic conditions, allowing the preparation of samples down to 20 and 50 µm in diameter, respectively, within minutes. Case studies are presented involving the preparation of a brittle biomineral brachiopod shell and cryogenically fixed soft brain tissue, and their examination by means of ptychographic X-ray computed tomography reveals the preparation method to be mainly free from causing artefacts. Since this lathe system easily yields near-cylindrical samples ideal for tomography, a usage for a wide variety of otherwise challenging specimens is anticipated, in addition to potential use as a time- and cost-saving tool prior to focused ion-beam milling. Fast sample preparation becomes especially important in relation to shorter measurement times expected in next-generation synchrotron sources.

36 MATERIALS SCIENCE↗