Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wake model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Large-Eddy Simulation Study of Wake Propagation and Power Production in an Array of Tidal-Current Turbines: Preprint

This paper presents our initial work in performing large-eddy simulations of tidal turbine array flows. First, a horizontally-periodic precursor simulation is performed to create turbulent flow data. Then that data is used as inflow into a tidal turbine array two rows deep and infinitely wide. The turbines are modeled using rotating actuator lines, and the finite-volume method is used to solvethe governing equations. In studying the wakes created by the turbines, we observed that the vertical shear of the inflow combined with wake rotation causes lateral wake asymmetry. Also, various turbine configurations are simulated, and the total power production relative to isolated turbines is examined. Staggering consecutive rows of turbines in the simulated configurations allows the greatestefficiency using the least downstream row spacing. Counter-rotating consecutive downstream turbines in a non-staggered array shows a small benefit. This work has identified areas for improvement, such as the use of a larger precursor domain to better capture elongated turbulent structures, the inclusion of salinity and temperature equations to account for density stratification and its effect onturbulence, improved wall shear stress modelling, and the examination of more array configurations.

16 TIDAL AND WAVE POWER↗

Progress in the prediction of unsteady heat transfer on turbines blades

Progress toward developing a general method for predicting unsteady heat transfer on turbine blades subject to blade-passing frequencies and Reynolds numbers relevant to the Space Shuttle Main Engine (SSME) is discussed. The method employs an invisid/viscous interactive procedure which has been tested extensively for steady subsonic and transonic external airfoil problems. One such example is shown. The agreement with experimental data and with Navier-Stokes calculations yields confidence in the method. The technique is extended to account for wake generated unsteadiness. The flow reversals around the stagnation point caused by the nonuniform onset velocity are accounted for by using the Characteristic Box scheme developed by Cebeci and Stewartson. The coupling between the inviscid and viscous methods is achieved by using a special procedure, which, with a novel inverse finite-difference boundary-layer method, allows the calculations to be performed for a wide range of flow conditions, including separation. Preliminary results are presented for the stagnation region of turbine blades for both laminar and turbulent flows. A laminar model problem corresponding to a flow on a circular cylinder which experiences the periodic passing of wakes from turbine blades is presented to demonstrate the ability of the method to calculate flow reversals around the stagnation region.

Cebeci, T.↗

Vortex research facility improvements and preliminary density stratification effects on vortex wakes

Recent modernization of NASA's Vortex Research Facility is described. The facility has a 300-ft test section, scheduled for a 300-ft extension, with constant test speeds of the model up to 100 ft/sec. The data acquisition hardware and software improvements included the installation of a 24-channel PCM system onboard the research vehicle, and a large dedicated 16-bit minicomputer. Flow visualization of the vortex wake in the test section is by particle seeding, and a thin sheet of argon laser light perpendicular to the line of flight; detailed flow field measurements are made with a laser velocimeter optics system. The improved experimental capabilities of the facility were used in a study of atmospheric stratification effects on wake vortex decay, showing that the effects of temperature gradient must be taken into account to avoid misleading conclusions in wake vortex research.

Satran, D. R.↗

Visualizing How the Structure of Large-Radius Jets Shapes Their Wakes

The ATLAS collaboration has introduced and implemented a strategy for selecting and analyzing large-radius jets composed of skinny $R=0.2$ subjets in heavy ion collisions at the LHC. We show how measurements of these jets teach us about the resolution length $L_{\rm res}$ of quark-gluon plasma (QGP) and can teach us how jet substructure shapes the wakes that jets excite in the QGP droplets through which they pass. We use Hybrid Model calculations to reproduce measurements of $R_{AA}$ for large-radius jets in PbPb collisions, and study their dependence on the angle between the two skinny subjets involved in the final reclustering step of an $R=1$ jet. We show how these observables can constrain the value of $L_{\rm res}$ and demonstrate that the ATLAS data rule out any picture in which an entire parton shower loses energy coherently as if it were a single entity. Determining the degree to which the QGP can resolve partons within a jet is central to the broader program of using jet quenching measurements to probe QGP. We make further use of this setup by analyzing the response of the medium to the passage of large-radius $R=2$ jets containing two skinny subjets in gamma-jet events. We introduce novel jet-shape observables that allow us to visualize the angular shape of the soft hadrons originating from the wakes that wide jets with two skinny subjets excite in a droplet of QGP, as a function of the angular separation between the subjets. We find that even when they are $\sim 0.8- 1$ radian apart, a single broad wake is produced. Only when the two subjets are even farther apart is the presence of two sub-wakes revealed. We show that the way in which jet structure shapes jet wakes can be visualized with similar clarity in experiments by using only those hadrons with low $p_T$. These observables thus offer a new and distinctive way of seeing jet wakes in heavy ion collision data.

FOS: Physical sciences↗

Correlation of SA349/2 helicopter flight-test data with a comprehensive rotorcraft model

A comprehensive rotorcraft analysis model was used to predict blade aerodynamic and structural loads for comparison with flight test data. The data were obtained from an SA349/2 helicopter with an advanced geometry rotor. Sensitivity of the correlation to wake geometry, blade dynamics, and blade aerodynamic effects was investigated. Blade chordwise pressure coefficients were predicted for the blade transonic regimes using the model coupled with two finite-difference codes.

Yamauchi, Gloria K.↗

Correlation of SA349/2 helicopter flight-test data with a comprehensive rotorcraft model

A comprehensive rotorcraft analysis model was used to predict blade aerodynamic and structural loads for comparison with flight test data. The data were obtained from an SA349/2 helicopter with an advanced geometry rotor. Sensitivity of the correlation to wake geometry, blade dynamics, and blade aerodynamic effects was investigated. Blade chordwise pressure coefficients were predicted for the blade transonic regimes using the model coupled with two finite-difference codes.

Yamauchi, Gloria K.↗

A Simple Analytical Fuselage-Induced Velocity Model for Comprehensive Rotor Codes

A simple analytical model to account for fuselage-induced velocities at rotor blade elements and at rotor wake nodes is described. The method is applied to three different fuselage configurations. Results obtained with a comprehensive rotor code show the fuselage effect on rotor trim controls, comparing the isolated rotor with inclusion of the fuselage for the same trim. This is compared to a simple analytical estimate of the fuselage effect using blade element/momentum theory. It is found that in forward flight the lateral control is mainly affected by fuselage effects. Rotor thrust can be varied by the presence of the fuselage, depending on its angle of attack, and the fuselage influence generally increases with flight speed.

Velocity Model↗

Measurement of Vortex Strength and Core Diameter in the Wake of a Hovering Rotor

Detailed hot wire measurements have been acquired in the tip vortex of a three-bladed model tilt rotor in hover. Testing was conducted at a rotor tip speed of 752 ft/sec, a Reynolds number (based on blade tip chord) of 1.77 x 10(exp 6), for thrust coefficients up to 0.0160. A figure shows the hot wire mounted above the inverted rotor at the Outside Aerodynamic Rotor Facility (OARF) at NASA Ames Research Center. Strobed shadowgraph flow visualization was used to define the vortex trajectory as an aid in hot wire positioning. Considerable variations in tip vortex structure with time were observed, even from the same blade, under essentially uniform test conditions. The only velocity signatures analyzed were those corresponding to passage of the probe directly through the center of the vortex. These time histories were ensemble averaged after compensating for jitter in the vortex arrival time at the probe, thereby retaining the core structure with minimal smearing. An example of a mean velocity signature, after ensemble averaging, is shown. The mean velocity signature was analyzed under the assumption of constant (unknown) translation speed of the vortex filament past the fixed probe. The translation speed of the vortex is deduced and the vortex strength and core diameter inferred. The results were highly unexpected. The indicated vortex strength is seen to decrease rapidly after first blade passage. In addition, the core radius is seen to decrease with increasing wake age, not increase as might be expected from simple diffusion.

Wadcock, Alan J.↗

Numerical solution of three-dimensional free turbulent shear flows

Numerical results are presented for three-dimensional compressible turbulent jet and wake flows. An alternating direction implicit numerical procedure is used to solve the finite-difference form of the parabolic elliptic Navier-Stokes equations. A coordinate transformation maps the boundaries at infinity into a finite computational domain in order to properly specify infinity boundary conditions as well as contain the downstream growth of the viscous flow field in a fixed computational grid. Turbulence closure is achieved through an algebraic mixing length eddy viscosity model. Numerical results for supersonic flow are presented for an axisymmetric jet, an elliptical jet, an elliptical wake, and two interacting rectangular jets. Experimental data were not available for comparison with the numerical results. However, the results compare well with empirical results for free shear flows.

Oh, Y. H.↗

Guidelines for volume force distributions within actuator line modeling of wind turbines on large-eddy simulation-type grids

The objective of this work is to develop and test a set of general guidelines for choosing parameters to be used in the state-of-the-art actuator line method (ALM) for modeling wind turbine blades in computational fluid dynamics (CFD). The actuator line method is being increasingly used for the computation of wake interactions in large wind farms in which fully blade-resolving simulations are expensive and require complicated rotating meshes. The focus is on actuator line behavior using fairly isotropic grids of low aspect ratio typically used for large-eddy simulation (LES). Forces predicted along the actuator lines need to be projected onto the flow field as body forces, and this is commonly accomplished using a volumetric projection. In this study, particular attention is given to the spanwise distribution of the radius of this projection. A new method is proposed where the projection radius varies along the blade span following an elliptic distribution. The proposed guidelines for actuator line parameters are applied to the National Renewable Energy Laboratory's (NREL's) Phase VI rotor and the NREL 5-MW turbine. Results obtained are compared with available data and the blade-element code XTurb-PSU. As a result, it is found that the new criterion for the projection radius leads to improved prediction of blade tip loads for both blade designs.

17 WIND ENERGY↗

On helicopter rotor low frequency broadband noise

The effect of shear-layer-type inflow turbulence on the low-frequency broadband noise of a model helicopter rotor is experimentally studied. The measurements and the one-dimensional energy spectral density indicate that the upstream airfoil wake turbulence is nonisotropic, but approaches isotropy at high wavenumbers. Turbulence measurements also indicate that the wake turbulence is weak. The effect of the inflow turbulence intensity on the peak sound pressure level follows an intensity-velocity squared scaling law. A number of length scales and turbulence intensities exist which can be measured in the airfoil wake depending on the position at which the measurements are taken. Comparison of experimental and theoretical sound pressure power spectral densities indicates that the initial anisotropy of the inflow turbulence does not invalidate the isotropic turbulence assumption made in noise prediction models as long as measured turbulence intensities and length scales are used.

Williams, Morgan↗

Large-eddy simulation of helical- and straight-bladed vertical-axis wind turbines in boundary layer turbulence

Here, turbulent wake flows behind helical- and straight-bladed vertical axis wind turbines (VAWTs) in boundary layer turbulence are numerically studied using the large-eddy simulation (LES) method combined with the actuator line model. Based on the LES data, systematic statistical analyses are performed to explore the effects of blade geometry on the characteristics of the turbine wake. The time-averaged velocity fields show that the helical-bladed VAWT generates a mean vertical velocity along the center of the turbine wake, which causes a vertical inclination of the turbine wake and alters the vertical gradient of the mean streamwise velocity. Consequently, the intensities of the turbulent fluctuations and Reynolds shear stresses are also affected by the helical-shaped blades when compared with those in the straight-bladed VAWT case. The LES results also show that reversing the twist direction of the helical-bladed VAWT causes the spatial patterns of the turbulent wake flow statistics to be reversed in the vertical direction. Moreover, the mass and kinetic energy transports in the turbine wakes are directly visualized using the transport tube method, and the comparison between the helical- and straight-bladed VAWT cases show significant differences in the downstream evolution of the transport tubes.

17 WIND ENERGY↗

Aircraft wake flow effect and horizontal tail buffet

As part of a program to investigate the fluctuating pressure distribution and response behavior of a fighter aircraft in transonic maneuver, an F-5A scale model has previously been tested in an 11-ft transonic wind tunnel. The model, with a number of static and dynamic pressure transducers imbedded in the lifting surfaces was tested at various angles of attack up to 16 deg. In this paper, test results of particular interest to wake flow and horizontal tail buffet are described. It is shown that the dynamic pressure data on the tail surface at the specified flight conditions serve to determine the local dynamic loads. They also influence the control performance of the aircraft under maneuver conditions where buffet is encountered. The data presented demonstrate a number of contributing factors that affect the tail dynamic pressures in the transonic regime.

Hwang, C.↗

Integrating a ponderomotive guiding center algorithm into a quasi-static particle-in-cell code based on azimuthal mode decomposition

High fidelity modeling of plasma based acceleration (PBA) requires the use of three dimensional, fully nonlinear, and kinetic descriptions based on the particle-in-cell (PIC) method. In PBA an intense particle beam or laser (driver) propagates through a tenuous plasma whereby it excites a plasma wave wake. Three-dimensional PIC algorithms based on the quasi-static approximation (QSA) have been successfully applied to efficiently model the interaction between relativistic charged particle beams and plasma. In a QSA PIC algorithm, the plasma response to a charged particle beam or laser driver is calculated based on forces from the driver and self-consistent forces from the QSA form of Maxwell's equations. These fields are then used to advance the charged particle beam or laser forward by a large time step. Since the time step is not limited by the regular Courant-Friedrichs-Lewy (CFL) condition that constrains a standard 3D fully electromagnetic PIC code, a 3D QSA PIC code can achieve orders of magnitude speedup in performance. Recently, a new hybrid QSA PIC algorithm that combines another speedup technique known as an azimuthal Fourier decomposition has been proposed and implemented. This hybrid algorithm decomposes the electromagnetic fields, charge and current density into azimuthal harmonics and only the Fourier coefficients need to be updated, which can reduce the algorithmic complexity of a 3D code to that of a 2D code. Modeling the laser-plasma interaction in a full 3D electromagnetic PIC algorithm is very computationally expensive due the enormous disparity of physical scales to be resolved. In the QSA the laser is modeled using the ponderomotive guiding center (PGC) approach. We describe how to implement a PGC algorithm compatible for the QSA PIC algorithms based on the azimuthal mode expansion. Here this algorithm permits time steps orders of magnitude larger than the cell size and it can be asynchronously parallelized. Details on how this is implemented into the QSA PIC code that utilizes an azimuthal mode expansion, QPAD, are also described. Benchmarks and comparisons between a fully 3D explicit PIC code (OSIRIS), as well as a few examples related to laser wakefield acceleration, are presented.

97 MATHEMATICS AND COMPUTING↗

Transition Analysis for Isolated Trips on BOLT-II Wind-Tunnel and Flight Configuration

The BOLT-II configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. The present paper is related to the NASA-led roughness experiment on the secondary side of the BOLT-II configuration. First, computations are performed to aid mean-flow based correlations for the transition measurements acquired during an experimental campaign in the Ludwieg Tube facility at the United States Air Force Academy. To that end, both laminar and turbulent flow computations are performed for selected conditions of the experiment with a 1:3 scale model of the slightly shorter BOLT configuration. The variation in well-known correlation parameters for transition due to isolated roughness elements with respect to element position, height, and flow Reynolds number is delineated. Furthermore, the wake instability theory is used to examine the amplification of unstable disturbances behind the centerline trip at the design conditions of the BOLT-II flight experiment and for its dynamically scaled version on the 1:3 scale model of the wind tunnel experiment. To our knowledge, this study represents the first analysis of the wake instabilities in the presence of a prominent entropy layer outside the boundary layer. At the nominal flight design condition of Re ∞ ) = 5.44 and Re ∞ = 2.5 x 10 6 /m, a diamond planform (“pizza-box”) trip with k/δ = 0.70 and planform-halfwidth-to-height ratio of b/k = 3.0 at X/L = 0.254 induces a strong distortion of the boundary-layer flow in the vicinity of the symmetry plane, such that the wake structure includes a centerline streak produced by the flow retardation behind the trip along with multiple additional, prominent vorticity structures representing the necklace vortex system. Stability results reveal that each of these streaks can support a strong amplification of wake instabilities within a frequency band of 95 kHz–255 kHz, with a peak N-factor of greater than 15 beyond X/L ≈ 0.42. The dynamically scaled wind tunnel configuration with Re ∞ = 20.25 x 10 6 /m is also found to support N > 15 at similar axial stations.

BOLT↗

Application of Three-Component PIV to a Hovering Rotor Wake

The key to accurate predictions of rotorcraft aerodynamics, acoustics, and dynamics lies in the accurate representation of the rotor wake. The vortical wake computed by rotorcraft CFD analyses typically suffer from numerical dissipation before the first blade passage. With some a priori knowledge of the wake trajectory, grid points can be concentrated along the trajectory to minimize the dissipation. Comprehensive rotorcraft analyses based on lifting-line theory rely on classical vortex models and/or semi-empirical information about the tip vortex structure. Until the location, size, and strength of the trailed tip vortex can be measured over a range of wake ages, the analyses will continue to be adjusted on a trial and error basis in order to correctly predict blade airloads, acoustics, dynamics, and performance. Using the laser light sheet technique, tip vortex location can be acquired in a straightforward manner. Measuring wake velocities and vortex core size, however, has been difficult and tedious using point-measurement techniques such as laser velocimetry. Recently, the Particle Image Velocimetry (PIV) technique has proven to be an efficient method for acquiring velocity measurements over relatively large areas and volumes of a rotor wake. The work reported to date, however, has been restricted to 2-component velocity measurements of the rotor wake. Three-component velocity measurements of a hovering rotor wake were acquired at NASA Ames Research Center in May 1999. This experiment represents a major step toward understanding the detailed structure of a rotor wake. This paper will focus primarily on the experimental technique used in acquiring this data. The accuracy and limitations of the current technique will also be discussed. Representative velocity field measurements will be included.

Yamauchi, Gloria K.↗

Study of electron trapping by a transversely ellipsoidal bubble in the laser wake-field acceleration

We present electron trapping in an ellipsoidal bubble which is not well explained by the spherical bubble model by [Kostyukov et al., Phys. Rev. Lett. 103, 175003 (2009)]. The formation of an ellipsoidal bubble, which is elongated transversely, frequently occurs when the spot size of the laser pulse is large compared to the plasma wavelength. First, we introduce the relation between the bubble size and the field slope inside the bubble in longitudinal and transverse directions. Then, we provide an ellipsoidal model of the bubble potential and investigate the electron trapping condition by numerical integration of the equations of motion. We found that the ellipsoidal model gives a significantly less restrictive trapping condition than that of the spherical bubble model. The trapping condition is compared with three-dimensional particle-in-cell simulations and the electron trajectory in test potential simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗