Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Fluctuating pressure loads under high speed boundary layers

Aeroacoustic fatigue is anticipated to control the design of significant portions of the structures of high-speed vehicles. This is due to contemplated long-duration flights at high dynamic pressures and Mach numbers with related high skin temperatures. Fluctuating pressure loads are comparatively small beneath attached turbulent boundary layers, but become important in regions of flow separation such as compression and expansion corners on elevons and rudders. The most intense loads are due to shock/boundary-layer interaction. These flows may occur in the engine-exhaust wall jet and in flows over control surfaces. A brief review is given of available research in these areas with a description of work under way at Langley Research Center.

Zorumski, William E.↗
NASA NTRS1986

Independent Orbiter Assessment (IOA): Analysis of the hydraulics/water spray boiler subsystem

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) are presented. The IOA approach features a top-down analysis of the hardware to determine failure modes, criticality, and potential critical items (PCIs). To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. This report documents the independent analysis results for the Orbiter Hydraulics/Water Spray Boiler Subsystem. The hydraulic system provides hydraulic power to gimbal the main engines, actuate the main engine propellant control valves, move the aerodynamic flight control surfaces, lower the landing gear, apply wheel brakes, steer the nosewheel, and dampen the external tank (ET) separation. Each hydraulic system has an associated water spray boiler which is used to cool the hydraulic fluid and APU lubricating oil. The IOA analysis process utilized available HYD/WSB hardware drawings, schematics and documents for defining hardware assemblies, components, and hardware items. Each level of hardware was evaluated and analyzed for possible failure modes and effects. Criticality was assigned based upon the severity of the effect for each failure mode. Of the 430 failure modes analyzed, 166 were determined to be PCIs.

Duval, J. D.↗
NASA NTRS1991

Navier-Stokes calculations of scramjet-nozzle-afterbody flowfields

A comprehensive computational fluid dynamics effort was conducted from 1987 to 1990 to properly design a nozzle and lower aft end of a generic hypersonic vehicle powered by a scramjet engine. The interference of the exhaust on the control surfaces of the vehicle can have adverse effects on its stability. Two-dimensional Navier-Stokes computations were performed, where the exhaust gas was assumed to be air behaving as a perfect gas. Then the exhaust was simulated by a mixture of Freon-12 and argon, which required solving the Navier-Stokes equations for four species: (nitrogen, oxygen, Freon-12, and argon). This allowed gamma to be a field variable during the mixing of the multispecies gases. Two different mixing models were used and comparisons between them as well as the perfect gas air calculations were made to assess their relative merits. Finally, the three dimensional Navier-Stokes computations were made for the full-span scramjet nozzle afterbody module.

Baysal, Oktay↗
NASA NTRS1990

Evaluation of RSRM case hardware fretting concerns

Fretting corrosion was first noted on Shuttle flight STS-26. This flight was the first usage of the Redesigned Solid Rocket Motor (RSRM). The occurrence of fretting has since been observed on both the field and factory joints of the RSRM. Fretting is a form of corrosion that occurs at the interface between contacting, highly loaded, metal surfaces when exposed to slight relative vibratory motions. The engineering effort performed to evaluate the effect of fretting on the RSRM case hardware is summarized. Based on the results of this evaluation, several conclusions were made concerning flight safety. Also, recommendations were made concerning trending the effects of multiple generations of fretting damage.

Swauger, Thomas R.↗
NASA NTRS1994

Boundary-Layer Code For Supersonic Combustion

HUD is integral computer code based on Spaulding-Chi method for predicting development of boundary layers in laminar, transitional, and turbulent regions of flows on two-dimensional or axisymmetric bodies. Approximates nonequilibrium velocity profiles as well as local surface friction in presence of pressure gradient. Predicts transfer of heat in turbulent boundary layer in presence of high axial presure gradient. Provides for pressure gradients both normal and lateral to surfaces. Also used to estimate requirements for cooling scramjet engines. Because of this capability, HUD program incorporated into several scramjet-cycle-performance-analysis codes, including SCRAM (ARC-12338) and SRGULL (LEW-15093). Written in FORTRAN 77.

Pinckney, S. Z.↗
NASA NTRS1996

Video System For Inspecting Walls Of Cavities

Endoscopic video-imaging system generates panoramic image of part of wall of cavity surrounding tip of probe inserted in cavity. Not necessary to rotate probe to obtain panoramic image. If simple inspection without measurement required, device called "cylindrical light ring" mounted on probe to illuminate scene. Different illumination device used when required to measure distance of wall of cavity from cylindrical axis of probe. System used, for example, to inspect inner surface of tube, passage, or manifold located deep within engine or other complex structure.

Gilbert, John A.↗
NASA NTRS1998

Analysis of Hard Thin Film Coating

Marshall Space Flight Center (MSFC) is interested in developing hard thin film coating for bearings. The wearing of the bearing is an important problem for space flight engine. Hard thin film coating can drastically improve the surface of the bearing and improve the wear-endurance of the bearing. However, many fundamental problems in surface physics, plasma deposition, etc, need further research. The approach is using Electron Cyclotron Resonance Chemical Vapor Deposition (ECRCVD) to deposit hard thin film on stainless steel bearing. The thin films in consideration include SiC, SiN and other materials. An ECRCVD deposition system is being assembled at MSFC.

Shen, Dashen↗
NASA NTRS1998

Analysis of Hard Thin Film Coating

MSFC is interested in developing hard thin film coating for bearings. The wearing of the bearing is an important problem for space flight engine. Hard thin film coating can drastically improve the surface of the bearing and improve the wear-endurance of the bearing. However, many fundamental problems in surface physics, plasma deposition, etc, need further research. The approach is using electron cyclotron resonance chemical vapor deposition (ECRCVD) to deposit hard thin film an stainless steel bearing. The thin films in consideration include SiC, SiN and other materials. An ECRCVD deposition system is being assembled at MSFC.

Shen, Dashen↗
NASA NTRS2008

Monitoring Damage Accumulation in Ceramic Matrix Composites Using Electrical Resistivity

The electric resistance of woven SiC fiber reinforced SiC matrix composites were measured under tensile loading conditions. The results show that the electrical resistance is closely related to damage and that real-time information about the damage state can be obtained through monitoring of the resistance. Such self-sensing capability provides the possibility of on-board/in-situ damage detection and accurate life prediction for high-temperature ceramic matrix composites. Woven silicon carbide fiber-reinforced silicon carbide (SiC/SiC) ceramic matrix composites (CMC) possess unique properties such as high thermal conductivity, excellent creep resistance, improved toughness, and good environmental stability (oxidation resistance), making them particularly suitable for hot structure applications. In specific, CMCs could be applied to hot section components of gas turbines [1], aerojet engines [2], thermal protection systems [3], and hot control surfaces [4]. The benefits of implementing these materials include reduced cooling air requirements, lower weight, simpler component design, longer service life, and higher thrust [5]. It has been identified in NASA High Speed Research (HSR) program that the SiC/SiC CMC has the most promise for high temperature, high oxidation applications [6]. One of the critical issues in the successful application of CMCs is on-board or insitu assessment of the damage state and an accurate prediction of the remaining service life of a particular component. This is of great concern, since most CMC components envisioned for aerospace applications will be exposed to harsh environments and play a key role in the vehicle s safety. On-line health monitoring can enable prediction of remaining life; thus resulting in improved safety and reliability of structural components. Monitoring can also allow for appropriate corrections to be made in real time, therefore leading to the prevention of catastrophic failures. Most conventional nondestructive evaluation (NDE) techniques such as ultrasonic C-scan, x-ray, thermography, and eddy current are limited since they require structural components of complex geometry to be taken out of service for a substantial length of time for post-damage inspection and assessment. Furthermore, the typical NDE techniques are useful for identifying large interlaminar flaws, but insensitive to CMC materials flaws developed perpendicular to the surface under tensile creep conditions. There are techniques such as piezoelectric sensor [7,8], and optical fiber [9,10] that could be used for on-line health monitoring of CMC structures. However, these systems involve attaching an external sensor or putting special fibers in CMC composites, which would be problematic at high temperature applications.

Smith, Craig E.↗
NASA NTRS2012

Tile Surface Thermocouple Measurement Challenges from the Orbiter Boundary Layer Transition Flight Experiment

Hypersonic entry flight testing motivated by efforts seeking to characterize boundary layer transition on the Space Shuttle Orbiters have identified challenges in our ability to acquire high quality quantitative surface temperature measurements versus time. Five missions near the end of the Space Shuttle Program implemented a tile surface protuberance as a boundary layer trip together with tile surface thermocouples to capture temperature measurements during entry. Similar engineering implementations of these measurements on Discovery and Endeavor demonstrated unexpected measurement voltage response during the high heating portion of the entry trajectory. An assessment has been performed to characterize possible causes of the issues experienced during STS-119, STS-128, STS-131, STS-133 and STS-134 as well as similar issues encountered during other orbiter entries.

Charles H. Campbell↗
NASA NTRS2010

Barium Depletion in the NSTAR Discharge Cathode After 30,000 Hours of Operation

Dispenser hollow cathodes rely on a consumable supply of barium released by impregnant materials in the pores of a tungsten matrix to maintain a low work function surface. Examinations of cathode inserts from long duration ion engine tests show deposits of tungsten at the downstream end that appear to block the flow of barium from the interior. In addition, a numerical model of barium transport in the insert plasma indicates that the barium partial pressure in the insert may exceed the equilibrium vapor pressure of the dominant barium-producing reaction, and it was postulated previously that this would suppress barium loss in the upstream part of the insert. New measurements of the depth of barium depletion from a cathode insert operated for 30,352 hours reveal that barium loss is confined to a narrow region near the downstream end, confirming this hypothesis.

plasma transport↗
NASA NTRS2016

Cooling Effectiveness Measurements for Air Film Cooling of Thermal Barrier Coated Surfaces in a Burner Rig Environment Using Phosphor Thermometry

While the effects of thermal barrier coating (TBC) thermal protection and air film cooling effectiveness are usually studied separately, their contributions to combined cooling effectiveness are interdependent and are not simply additive. Therefore, combined cooling effectiveness must be measured to achieve an optimum balance between TBC thermal protection and air film cooling. In this investigation, surface temperature mapping was performed using recently developed Cr-doped GdAlO3 phosphor thermometry. Measurements were performed in the NASA GRC Mach 0.3 burner rig on a TBC-coated plate using a scaled up cooling hole geometry where both the mainstream hot gas temperature and the blowing ratio were varied. Procedures for surface temperature and cooling effectiveness mapping of the air film-cooled TBC-coated surface are described. Applications are also shown for an engine component in both the burner rig test environment as well as an engine afterburner environment. The effects of thermal background radiation and flame chemiluminescence on the measurements are investigated, and advantages of this method over infrared thermography as well as the limitations of this method for studying air film cooling are discussed.

air film cooling↗
NASA NTRS2019

Riders on the storm: NASA InSight Lander and the 2018 Mars global dust storm

As our spacecraft hurtled through interplanetary space towards its destination, the InSight team took stock of the situation. Would this enormous dust storm still be raging when InSight arrived? What, if anything, had this storm changed in the assumptions made by InSight’s design and test engineers about Martian atmospheric conditions for descending to the surface, or generating power there? Would InSight survive and carry out her mission?

Grover, Myron R.↗
NASA NTRSDate not supplied

Biofilm Management in a Microgravity Water Recovery System

Biofilm growth continues to be a significant concern for NASA’s current and future water systems. The International Space Station (ISS) Water Processor Assembly (WPA) produces potable water from a combination of humidity condensate and urine distillate. The WPA waste tank requires significant management to prevent biofilm growth from impacting downstream components. This issue is magnified for future NASA manned missions due to the need to place the vehicle’s life support system in a dormant state during uncrewed operations (e.g., when the vehicle is in Mars orbit during the surface mission). NASA personnel and the Center for Biofilm Engineering at Montana State University are evaluating various methods for mitigating biofilm growth, including reduced nutrient levels, thermal treatment, sonic waves treatment, and identifying effective biocides in this application. This paper provides an overview of the current status of this effort.

Yo-ann Velez Justiniano↗
NASA NTRSDate not supplied

Initial Testing the Exploration Extravehicular Mobility Unit (xEMU) in Lunar Environment Simulation at the Neutral Buoyancy Lab (NBL) in 2022

Understanding how to effectively train for Extravehicular Activities (EVAs) for Artemis missions is critical. Tasked by the new Extravehicular Activity and Human Surface Mobility Program(EHP), a team of stakeholders from engineering and flight operations worked together to test the Exploration Extravehicular Mobility (xEMU) in the Neutral Buoyancy Lab(NBL) simulating the lunar environment. The NBL is a pool in which astronauts are typically trained to complete simulated International Space Station (ISS) EVA tasks in a neutral weigh-out. The overall focus for this test series was evaluating how well the NBL could be used as an effective simulated environment for Artemis lunar EVAs. New NBL support hardware was manufactured to support this test series and update the interfaces to be more representative of xEMU hardware such as a new NBL Portable Life Support System(PLSS)mock-up and umbilical, lights and cameras, and display and control unit (DCU).To simulate the 1/6th-gravity (1/6-g) environment, extra weights were added around the suit to create an accurate center of gravity representation. The Partial Gravity Weigh-out Stand (PGWS) predicted where and how much weight would be required for the 1/6th-G simulation and predicted the center of gravity placement. After the weigh-out attempt was completed, the suited participant would complete a set of directed tasks such as kneeling, object pick-up, and walking to evaluate the weigh-out. To create the lunar environment, sand, boulders, and ramps were added to the pool floor. If time allowed after weigh-out was determined acceptable, the flight operations team would direct the suited participants to complete simulated Artemis EVA tasks using flight-like tools and tool cart. The team also evaluated turning out the overhead lights in the NBL for a portion of some of the test runs and using a solar simulator to create amore realistic lunar south pole lighting environment. The test series completed one unmanned test and nine manned tests. With four of the tests, dual xEMU suited operations were completed with subjects in both the small and large xEMU sizes. Overall, the NBL was able to create an acceptable lunar landscape and ability to have two subjects work side by side in pressurized xEMUs which currently cannot be achieved in other test environments. Achieving a stable 1/6th-G lunar weigh-out and clear, consistent dual suit communications was a challenge for this series. Future work is planned to continue to improve this simulation environment.

spacesuit↗
NASA NTRSDate not supplied

Testing the Exploration Conops (Excon) Mockup Suit in Lunar Analog Environments in 2022

Understanding how to effectively train for Extravehicular Activities (EVAs) for Artemis missions is critical. Developing high-fidelity simulation environments is important for Artemis mission preparation. Because the actual Lunar exploration environment cannot be fully replicated on Earth, it is paramount to determine where and how to properly train the Artemis team. Tasked by the new Extravehicular Activity and Human Surface Mobility Program(EHP), a team of stakeholders from engineering, flight operations, human health and performance, astromaterials and science, and the crew office worked together to perform EVAs in 3 simulated lunar environments. The overall focus for this test series was developing the capability to perform Artemis simulated EVAs in high-fidelity, full-scale environments. This test series was broken into 3 distinct tests titled after the EHP integrated test team: Joint EVA Test Team (JETT). The test locations are planned to serve as Artemis training sites and were selected because of their relevance to the expected Artemis Lunar terrain. JETT1was conducted near Kilbourne Holeby El Paso, Texas and focused on hardware development and checkout. JETT2 was conducted in the Icelandic Highlands and began the transition towards EVA concept operations(con-ops), risks and technology.JETT3 was conducted near SP Crater by Flagstaff Arizona and focused on simulating the Artemis III mission with a simulated Houston based Flight Control Team (FCT) and a Science Mission Directorate (SMD) science team. All three JETT tests utilized the Excon mockup space suit. The Excon mockup suit is a light-weight, unpressurized Exploration Extravehicular Mobility Unit (xEMU)simulator. While it cannot replicate the feel of working within a pressurized suit, it does introduce similar volume constraints and some of the mobility programing to simulate the user experience in the xEMU. Overall, the JETT testing was able to create a simulated Lunar EVA and have two subjects perform full scale operations in line with Artemis III mission expectations. Future work is planned to continue to improve the simulation quality of Lunar EVA simulations.

spacesuit↗
NASA NTRSDate not supplied

Initial Testing of the Exploration Extravehicular Mobility Unit (xEMU) in Lunar Environment Simulation at the Neutral Buoyancy Lab (NBL) in 2022

Understanding how to effectively train for Extravehicular Activities (EVAs) for Artemis missions is critical. Tasked by the new Extravehicular Activity and Human Surface Mobility Program(EHP), a team of stakeholders from engineering and flight operations worked together to test the Exploration Extravehicular Mobility (xEMU) in the Neutral Buoyancy Lab(NBL) simulating the lunar environment. The NBL is a pool in which astronauts are typically trained to complete simulated International Space Station (ISS) EVA tasks in a neutral weigh-out. The overall focus for this test series was evaluating how well the NBL could be used as an effective simulated environment for Artemis lunar EVAs. New NBL support hardware was manufactured to support this test series and update the interfaces to be more representative of xEMU hardware such as a new NBL Portable Life Support System(PLSS)mock-up and umbilical, lights and cameras, and display and control unit (DCU).To simulate the 1/6th-gravity (1/6-g) environment, extra weights were added around the suit to create an accurate center of gravity representation. The Partial Gravity Weigh-out Stand (PGWS) predicted where and how much weight would be required for the 1/6th-G simulation and predicted the center of gravity placement. After the weigh-out attempt was completed, the suited participant would complete a set of directed tasks such as kneeling, object pick-up, and walking to evaluate the weigh-out. To create the lunar environment, sand, boulders, and ramps were added to the pool floor. If time allowed after weigh-out was determined acceptable, the flight operations team would direct the suited participants to complete simulated Artemis EVA tasks using flight-like tools and tool cart. The team also evaluated turning out the overhead lights in the NBL for a portion of some of the test runs and using a solar simulator to create amore realistic lunar south pole lighting environment. The test series completed one unmanned test and nine manned tests. With four of the tests, dual xEMU suited operations were completed with subjects in both the small and large xEMU sizes. Overall, the NBL was able to create an acceptable lunar landscape and ability to have two subjects work side by side in pressurized xEMUs which currently cannot be achieved in other test environments. Achieving a stable 1/6th-G lunar weigh-out and clear, consistent dual suit communications was a challenge for this series. Future work is planned to continue to improve this simulation environment.

spacesuit↗
DOE OSTI2024

Methods of controllable interstitial oxygen doping in niobium

A method for vacuum heat treating Nb, such as is used in superconducting radio frequency cavities, to engineer the interstitial oxygen profile with depth into the surface to conveniently optimize the low-temperature rf surface resistance of the material. An example application is heating of 1.3 GHz accelerating structures between 250-400° C. to achieve a very high quality factor of 5×1010 at 2.0 K. With data supplied by secondary ion mass spectrometry measurements, application of oxide decomposition and oxygen diffusion theory was applied to quantify previously unknown parameters crucial in achieving the oxygen alloy concentration profiles required to optimize the rf surface resistance. RF measurements of vacuum heat treated Nb superconducting radio frequency cavities confirmed the minimized surface resistance (higher Q0) previously expected only from 800° C. diffusive alloying with nitrogen.

Palczewski, Ari D.↗