Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shape optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Interface Shape and Convection During Solidification and Melting of Succinonitrile

An experimental study was conducted of the crystal growth of succinonitrile during solidification, melting, and no-growth conditions using a horizontal Bridgman furnace and square glass ampoule. For use as input boundary conditions to numerical codes, thermal profiles on the outside of the ampoule at five locations around its periphery were measured along the ampoule's length. Temperatures inside the ampoule were also measured. The shapes of the s/l interface in various two dimensional planes were quantitatively determined. Though interfaces were nondendritic and noncellular, they were not flat, but were highly curved and symmetric in only one unique longitudinal y-z plane (at x=O). The shapes of the interface were dominated by the primary longitudinal flow cell characteristic of shallow cavity flow in horizontal Bridgman; this flow cell was driven by the imposed furnace temperature gradient and caused a 'radical' thermal gradient such that the upper half of the ampoule was hotter than the bottom half. We believe that due to the strong convection, the release of latent heat does not significantly influence the thermal conditions near the interface. We hope that the interface shape and thermal data presented in this paper can be used to optimize crystal growth processes and validate numerical models.

Degroh, Henry C., III↗

Modeling and Correcting the Time-Dependent ACS PSF

The ability to accurately measure the shapes of faint objects in images taken with the Advanced Camera for Surveys (ACS) on the Hubble Space Telescope (HST) depends upon detailed knowledge of the Point Spread Function (PSF). We show that thermal fluctuations cause the PSF of the ACS Wide Field Camera (WFC) to vary over time. We describe a modified version of the TinyTim PSF modeling software to create artificial grids of stars across the ACS field of view at a range of telescope focus values. These models closely resemble the stars in real ACS images. Using 10 bright stars in a real image, we have been able to measure HST s apparent focus at the time of the exposure. TinyTim can then be used to model the PSF at any position on the ACS field of view. This obviates the need for images of dense stellar fields at different focus values, or interpolation between the few observed stars. We show that residual differences between our TinyTim models and real data are likely due to the effects of Charge Transfer Efficiency (CTE) degradation. Furthermore, we discuss stochastic noise that is added to the shape of point sources when distortion is removed, and we present MultiDrizzle parameters that are optimal for weak lensing science. Specifically, we find that reducing the MultiDrizzle output pixel scale and choosing a Gaussian kernel significantly stabilizes the resulting PSF after image combination, while still eliminating cosmic rays/bad pixels, and correcting the large geometric distortion in the ACS. We discuss future plans, which include more detailed study of the effects of CTE degradation on object shapes and releasing our TinyTim models to the astronomical community.

Rhodes, Jason↗

Fairing Separation Analysis Using SepTOOL

This document describes the relevant equations programmed in spreadsheet software, SepTOOL, developed by ZIN Technologies, Inc. (ZIN) to determine the separation clearance between a launch vehicle payload fairing and remaining stages. The software uses closed form rigid body dynamic solutions of the vehicle in combination with flexible body dynamics of the fairing, which is obtained from flexible body dynamic analysis or from test data, and superimposes the two results to obtain minimum separation clearance for any given set of flight trajectory conditions. Using closed form solutions allows SepTOOL to perform separation calculations several orders of magnitude faster compared to numerical methods which allows users to perform real time parameter studies. Moreover, SepTOOL can optimize vehicle performance to minimize separation clearance. This tool can evaluate various shapes and sizes of fairings along with different vehicle configurations and trajectories. These geometries and parameters are inputted in a user friendly interface. Although the software was specifically developed for evaluating the separation clearance of launch vehicle payload fairings, separation dynamics of other launch vehicle components can be evaluated provided that aerodynamic loads acting on the vehicle during the separation event are negligible. This document describes the development of SepTOOL providing analytical procedure and theoretical equations whose implementation of these equations is not disclosed. Realistic examples are presented, and the results are verified with ADAMS (MSC Software Corporation) simulations. It should be noted that SepTOOL is a preliminary separation clearance assessment software for payload fairings and should not be used for final clearance analysis.

fairings↗

Hot Isostatic Pressing for Reduction of Defects in Additively Manufactured Inconel-718 Preliminary Simulation Approach and Results

Selective laser melting (SLM) of Inconel-718 (IN718) is a promising advanced manufacturing technology; however, challenges exist for fracture-critical parts where pores induced during the manufacturing process reduce fatigue life of the material. Hot isostatic pressing (HIP) is a common post processing technique used to reduce the part porosity by exposing parts to high temperature and pressures. Pore closure depends on the pore shape, trapped gas, and HIP parameters, and the process can only be optimized by understanding the effect of these variables. An analysis capability is described to better understand the conditions necessary for pore closure, and the effect of several variables on porosity are explored and compared to a baseline case. The importance of valid material response models is identified as a significant factor in model accuracy; especially the creep material response model which, in the baseline case, predicts that creep strain accounts for 87.7% of the total strain at the conclusion of the HIP cycle. Lessons learned are described, in addition to future work including model validation.

Joshua M Fody↗

SRF Cavity High-Gradient Study at 805 MHz for Proton and Other Applications

805 MHz elliptical SRF cavities have been used for SNS as the first application for protons. At LANL, an R&D started to explore a capability of getting high-gradient cavities (40-50 MV/m) at this frequency for the future applications such as proton and muon based interrogation testing facility added to the LANSCE accelerator and a power upgrade of the LANSCE accelerator for the fission and fusion material test station. Optimized cell designs for “standard”, “low-loss” and “re-entrant” shapes, cavity test results for “standard” single-cell cavities with temperature mapping as well as surface inspection results will be presented.

43 PARTICLE ACCELERATORS↗

All-Digital Time-Resolved Spot Diagnostic

Presentation describes research into construction of a time-resolved spot diagnostic using mostly commercial off-the-shelf components, with system requirements to include (among others) comparable or better signal-to-noise ratio than a streak camera; low-loss fiber network, likely less than a few dB; optimized interface to the scintillators; and fast detectors to capture the pulse shape, 500 MHz to 1 GHz analog bandwidth with good linearity.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Optimal location of actuators for correcting distortions due to manufacturing errors in large truss structures

A continuum approximation to the calculation of the statistical properties of the corrected shape of a beam truss is presented, and results of a comparison with the exact statistical analysis were found to be very good. In addition, the position of the actuators was optimized to minimize the weighted rms of the distortion using the continuum analysis. The optimal design is shown to be 13.6 percent better than a uniform design for a parabolic weighting function. It was also found that actuators located on the beam face elements were more effective than actuators located on the diagonal elements.

Burdisso, R.↗

Growth interface study of CdTeSe crystals grown by the THM technique

The Traveling Heater Method (THM) is a widely accepted technique to grow high-quality detector grade CdTe and CdZnTe ingots, especially for X-ray and gamma-ray detector applications. Unlike melt-growth techniques, the growth interface for ingots produced by the THM technique consists of two different compounds, viz. the solidified region (just below the interface) consists of the compound to be grown (e.g., CdZnTe for CdZnTe growth), while the molten zone just above the growth interface consists of Te-rich CdZnTe. Thus, optimization of the growth parameters is critical to obtain a clean growth interface with the required shape and presence of minimal Te-rich inclusions. Here, in this study, CdTeSe ingots were grown employing the THM technique to investigate the growth interface. Both macroscopic and microscopic behavior of the interface were studied. The study revealed that a microscopically smooth growth interface can be achieved by optimizing the growth parameters, which is essential for obtaining high-quality, inclusion-free ingots.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Modal Response of Trapezoidal Wing Structures Using Second Order Shape Sensitivities

The modal response of wing structures is very important for assessing their dynamic response including dynamic aeroelastic instabilities. Moreover, in a recent study an efficient structural optimization approach was developed using structural modes to represent the static aeroelastic wing response (both displacement and stress). In this paper, the modal response of general trapezoidal wing structures is approximated using shape sensitivities up to the 2nd order. Also different approaches of computing the derivatives are investigated.

Liu, Youhua↗

Manipulating strong electromagnetic fields with the average transverse momentum of relativistic nuclear collisions

Abstract We show that an event-shape engineering based on the mean transverse momentum of charged hadrons, $$[p_t]$$ [ p t ] , provides an optimal handle on the strength of the magnetic field created in central heavy-ion collisions at high energy. This is established through quantitative evaluations of the correlation existing between the event-by-event magnetic field produced by the spectator protons in 5.02 TeV Pb + Pb collisions and the event-by-event $$[p_t]$$ [ p t ] at a given collision centrality. We argue that the event selection based on $$[p_t]$$ [ p t ] provides a better handle on the magnetic field than the more traditional selection based on the event ellipticities. Advantages brought by this new method for the experimental search of the chiral magnetic effect are discussed.

Giacalone, Giuliano (ORCID:0000000287761034)↗

Spectral Re-Growth Reduction for CCSDS 8-D 8-PSK TCM

This report presents a study on the CCSDS recommended 8-dimensional 8 PSK Trellis Coded Modulation (TCM) scheme. The important steps of the CCSDS scheme include: conversion of serial data into parallel form, differential encoding, convolutional encoding, constellation mapping, and filtering the 8-PSK symbols using the square root raised cosine (SRRC) pulses. The last step, namely the filtering of the 8 PSK symbols using SRRC pulses, significantly affects the bandwidth of the signal. If a nonlinear power amplifier is used, the SRRC filtered signal creates spectral regrowth. The purpose of this report is to investigate a technique, called the smooth phase interpolated keying (SPIK), that can provide an alternative to SRRC filtering so that good spectral as well as power efficiencies can be obtained with the CCSDS encoder. The results of this study show that the CCSDS encoder does not affect the spectral shape of the SRRC filtered signal or the SPIK signal. When a nonlinear traveling wave tube amplifier (TWTA) is used, the spectral performance of the SRRC signal degrades significantly while the spectral performance of SPIK remains unaffected. The degrading effect of a nonlinear solid state power amplifier (SSPA) on SRRC is found to be less than that due to a nonlinear TWTA. However, in both cases, the spectral performance of the SRRC modulated signal is worse than that of the SPIK signal. The bit error rate (BER) performance of the SRRC signal in a linear amplifier environment is about 2.5 dB better than that of the SPIK signal when both the receivers use algorithms of similar complexity. In a nonlinear TWTA environment, the SRRC signal requires accurate phase tracking since the TWTA introduces additional phase distortion. This problem does not arise with SPIK signal due to its constant envelope property. When a nonlinear amplifier is used, the SRRC method loses nearly 1 dB in the bit error rate performance. The SPIK signal does not lose any performance. Thus the performance gap between SRRC and SPIK reduces. The BER performance of SPIK can be improved even further by using a more optimal receiver. A similar optimal receiver for SRRC is quite complex since the amplifier distorts the pulse shape. However, this requires further investigation and is not covered in this report.

Borah, Deva K.↗

Process Development and Optimization of a Direct Cast U-6Nb 250 mm Hemispherical Component

Direct Casting is the process of casting a near-net shape part of U-6wt%Nb in a multi-zone VIM furnace for subsequent heat treatment and machining in to a final component. This report describes work to further develop a sound technical basis and best practices for mold design and process parameters for the Direct Casting of U-6Nb components with a hemispherical geometry. Specifically, process parameters and mold design are examined in detail for producing a 250 mm diameter hemisphere component. The goal is to efficiently produce a sound casting with a minimum of microporosity and uniform niobium composition. Prior work had tried unsuccessfully to cast this shape in a large single-coil vacuum induction melting (VIM) furnace. These castings had unacceptable levels microporosity and niobium segregation. In this work, this same part was cast in a multi-zone VIM and a sound casting was obtained. Beyond simply casting a sound part, this work aimed to optimize the hot-top design, metal pouring temperature, and mold pole temperature. Sound castings where produced using both a tapered and step hot-top designs. There were slightly lower porosity levels and about 5% better metal usage with the step hot-top so that design slightly better. With the current mold design, which uses a funnel and filter arrangement, there a large amount of superheat loss in the funnel/filter during mold filling. This temperature loss, and the apparent variability in the filling behavior, lead to casting defects in the pole region of several of the castings. The variability and defects were overcome by moving to a higher mold pole temperature (850°C) and a higher metal pour temperature (1500°C). For future work it is believed that a no-funnel design, with the filter integral to the crucible, will be a better and more robust strategy.

42 ENGINEERING↗

On the placement of active members in adaptive truss structures for vibration control

The problem of optimal placement of active members which are used for vibration control in adaptive truss structures is investigated. The control scheme is based on the method of eigenvalue assignment as a means of shaping the transient response of the controlled adaptive structures, and the minimization of required control action is considered as the optimization criterion. To this end, a performance index which measures the control strokes of active members is formulated in an efficient way. In order to reduce the computation burden, particularly for the case where the locations of active members have to be selected from a large set of available sites, several heuristic searching schemes are proposed for obtaining the near-optimal locations. The proposed schemes significantly reduce the computational complexity of placing multiple active members to the order of that when a single active member is placed.

Lu, L.-Y.↗

Optimal design of acoustic metamaterial cloaks under uncertainty

In this work, we consider the problem of optimal design of an acoustic cloak under uncertainty and develop scalable approximation and optimization methods to solve this problem. The design variable is taken as an infinite-dimensional spatially-varying field that represents the material property, while an additive infinite-dimensional random field represents the variability of the material property or the manufacturing error. Discretization of this optimal design problem results in high-dimensional design variables and uncertain parameters. To solve this problem, we develop a computational approach based on a Taylor approximation and an approximate Newton method for optimization, which is based on a Hessian derived at the mean of the random field. We show our approach is scalable with respect to the dimension of both the design variables and uncertain parameters, in the sense that the necessary number of acoustic wave propagations is essentially independent of these dimensions, for numerical experiments with up to one million design variables and half a million uncertain parameters. Additionally, we demonstrate that, using our computational approach, an optimal design of the acoustic cloak that is robust to material uncertainty is achieved in a tractable manner. The optimal design under uncertainty problem is posed and solved for the classical circular obstacle surrounded by a ring-shaped cloaking region, subjected to both a single-direction single-frequency incident wave and multiple-direction multiple-frequency incident waves. Finally, we apply the method to a deterministic large-scale optimal cloaking problem with complex geometry, to demonstrate that the approximate Newton method’s Hessian computation is viable for large, complex problems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optimization of the conditions of synchrotron Mössbauer experiment for studying electronic transitions at high pressures by the example of (Mg, Fe)O magnesiowustite

The effect of the experimental conditions on the shape of the nuclear resonant forward scattering (NFS) from (Mg{sub 0.75}Fe{sub 0.25})O magnesiowustite has been studied at high pressures up to 100 GPa in diamond anvil cells by the method of the NFS of synchrotron radiation from the Fe-57 nuclei at room temperature. The behavior of the system in the electronic transition of the Fe{sup 2+} ion from the high-spin to low-spin state (spin crossover) near 62 GPa is analyzed as a function of the sample thickness, degree of nonhydrostaticity, and focusing and collimation conditions of a synchrotron beam. It is found that the inclusion of dynamical beats associated with the sample thickness is very important in the approximation of the experimental NFS spectra. It is shown that the electronic transition occurs in a much narrower pressure range ({+-}6 GPa) rather than in a broad range as erroneously follows from experiments with thick samples under strongly nonhydrostatic conditions.

43 PARTICLE ACCELERATORS↗

Framework for X-ray mirror surface shape fitting

For accurate characterization of grazing-incidence X-ray mirrors, we present a comprehensive framework to fit measured surface shapes (either slope or height) of X-ray mirrors used in synchrotron radiation and free-electron laser facilities. We summarize the closed-form expressions of some typical surface shapes of X-ray mirrors including elliptic cylinders, hyperbolic cylinders, ellipsoids, hyperboloids, and diaboloids. This framework is composed of four layers: definition of standard shapes with closed-form expressions, generation of theoretical surface with pose parameters (six degrees of freedom defining an object's position and orientation relative to a coordinate system), parameter optimization with the ability to select which parameters are fit and which are held constant, and the development of user-friendly fitting function wrappers for particular fitting tasks. A few practical fitting examples are demonstrated to verify the effectiveness of the proposed fitting framework. We discuss the physical meanings of the fitting parameters, and provide several examples using the elliptic cylinder and ellipsoid shapes to highlight some features of the framework. Moreover, we provide the presented framework as open-source codes (MATLAB and Python codes available at https://github.com/nsls2omf/xmf) to the community to encourage academic collaboration and further improvements.

36 MATERIALS SCIENCE↗

Numerical Simulation of One- and Two-Phase Flows in Propulsion Systems

Four subprojects were conducted using analytical methods, numerical simulation and experimental tests: (A) Shock wave mitigation by spike-shaped blunt bodies with application for the purpose of drag, lift and longitudinal momentum optimization. The main result in this subproject is: application of a single needle against a supersonic flow provides higher benefits for blunt body drag reduction and heat transfer to the body than the application of multiple needles. (B) Solid particles, liquid and air jet injection through the front of a blunt body against a supersonic flow. In this case, the research conducted and analysis of multiple previous investigations in this area have shown essential benefits and preferable application of solid particle injection. (C) Comparison of different methods of fuel injection into supersonic duct flows. Preliminary numerical simulations and theoretical analysis show promising results for Telescope-shaped inlet applications in SCRAMJET; and (D) Development of an acoustic source location method for different applications including propulsion systems.

Gilinsky, Mikhail↗

Optics Studies for Multipass Energy Recovery at CEBAF: ER@CEBAF

Energy recovery linacs (ERLs), focus on recycling the kinetic energy of electron beam for the purpose of accelerating a newly injected beam within the same accelerating structure. The rising developments in the super conducting radio frequency technology, ERL technology has achieved several noteworthy milestones over the past few decades. In year 2003, Jefferson Lab has successfully demonstrated a single pass energy recovery at the CEBAF accelerator. Furthermore, they conducted successful experiments with IR-FEL demo and upgrades, as well as the UV FEL driver. This multi-pass, multi-GeV range energy recovery demonstration proposed to be carried out at CEBAF accelerator at Jefferson Lab focuses on demonstrating highest energy recovery in super conducting linac in the low-current range. Continuous electron beam accelerate up to 7.5 GeV within 5-passes and decelerate in the next 5-passes recovering RF energy and dumps at a low energy dump. The beamline optics design for recirculating linacs require special attention to avoid beam instabilities due to RF wakefields. Usually, multi-pass linac beam lines require stronger focusing at lower energies as that is necessary to avoid beam breakup (BBU) instabilities, even with this small beam current. The CEBAF linac optics optimization is focused on balancing over-focusing at higher energies and beta excursions at lower energies. The race-track-shaped geometry of CEBAF accelerator allows its linacs to accommodate multiple energy beams simultaneously, while individual recirculating arcs transporting one beam energy, are shared between accelerating/decelerating beams. For the linac optics optimization process, an extended strategy is used that is originally used in 6-pass Recirculating Linac design of the LHeC, to represent the ten passes through a single linac. Using proper mathematical expressions, linac optics optimization can be achieved with evolutionary genetic algorithms, with Multi-Objective optimization. This thesis introduces a CEBAF optics redesign tailored to accommodates the ER@CEBAF multi-pass ER scheme. The isochronous arcs were retuned to match into optics solutions for optimized 10-pass linacs. Within this work, a single bunch particle tracking analysis presented here focuses on the further improvements of the beamline and beam transportation.

Neththikumara, Isurumali↗