Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mechanically Robust Bismuth-Embedded Carbon Microspheres for Ultrafast Charging and Ultrastable Sodium-Ion Batteries

Advancements in the development of fast-charging and long-lasting microstructured alloying anodes with high volumetric capacities are essential for enhancing the operational efficiency of sodium-ion batteries (SIBs). These anodes, however, face challenges such as declined cyclability and rate capability, primarily due to mechanical degradation reduced by significant volumetric changes (over 252%) and slow kinetics of sodium-ion storage. Herein, we introduce a novel anode design featuring densely packed bismuth (Bi) embedded within highly conductive carbon microspheres to overcome the aforementioned challenges. Remarkably, the high loading Bi anode within carbon microspheres with a high tap density of 2.59 g cm -3 possesses significant mechanical strength exceeding 590 MPa and limits volume swelling of only 10.9% post-sodiation. This anode demonstrates a high volumetric capacity (908.3 mAh cm -3 ), ultrafast chargeability (200 A g -1 , full charge/discharge in just 5.5 s), and outstanding cyclability over 12,000 cycles and maintains exceptional cycling stability even at -30 °C. The full cell paired with a Na 3 V 2 (PO 4 ) 3 cathode retains over 80% capacity after 600 cycles at 36 C, demonstrating a remarkable rate capability of 126 C (full charge/discharge in 28.6 s). Our comprehensive experimental evaluations and chemo-mechanical simulations shed light on the mechanisms underpinning the anode's superior performance. In conclusion, this development marks a significant advancement in the design of durable and fast-charging anodes for high-performance SIBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Synthesis of metallic glass nanoparticles by inert gas condensation

Inert Gas Condensation (IGC) is a versatile method for the synthesis of ultrafine nanoparticles. While it has been mostly used in the synthesis of nanocrystalline particles it has also been employed in the synthesis of metallic glass nanoparticles, which can be further used in the generation of nanostructured metallic glasses, known as nanoglasses. In this work, we use molecular dynamics simulations to investigate the IGC processes leading to the synthesis of Cu 64 Zr 36 amorphous nanoparticles. We investigate the growth of nanoparticles up to 7.3 nm diameter using long simulations of up to 130 ns, under relatively low pressures in the range of 4 to 10 bars. Results indicate a significant effect of pressure on the final structure of the amorphous nanoparticles, yet no clear influence on the segregation of Cu atoms to its surface. Cu segregation occurring at all pressures results in a thin Cu rich layer, about 2.5 Å thick, that coats all nanoparticles. Here, statistics of atomic Voronoi polyhedra shows that the fraction of full icosahedra in the nanoparticles produced at 4 bars is equivalent to that of bulk metallic glasses produced by melt and quench at 10 9 K/s. Higher pressures result in a lower fraction of full icosahedra.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tailoring composition and deformation modes at the microstructural level for next generation low-cost high-strength austenitic stainless steels

The objective of this project is to enable deliberate development of cost-effective, hydrogen resistant alloys by establishing detailed relationships specific to the effects of alloy composition, short-range order (SRO), and microsegregation in the presence of hydrogen on the transition between homogeneous deformation and localized plasticity in shear bands. In collaboration with the International Institute for Carbon-Neutral Energy Research, I2CNER, at Kyushu University in Japan, we conceptualized, designed, and manufactured four austenitic alloys that maintain corrosion resistance and ensure lower cost relative to baseline commercial alloys. The mechanical properties and deformation modes of the novel alloys (KU alloys) were assessed in the presence of hydrogen (H). Correlations between composition and performance revealed that two of the KU alloys are suitable replacements for 316 steel, while another is a viable replacement for 304 steel at room temperature. We found that, in the presence of other austenite stabilizing elements namely Mn and N, replacing Ni with Cu does not lead to martensite formation as has been previously reported.1–3 Furthermore, we found that the addition of Cu leads to an earlier onset of multiple slip resulting in an relative earlier onset of a higher work hardening rate (WHR). Greater understanding of the relationships between alloy composition and SRO required the development of a novel advanced electron diffraction methodology to characterize SRO in complex FCC alloys. This innovative approach, which combines fluctuation and correlation analyses of diffuse-scattering signals, successfully differentiated between SRO and long-range ordering (LRO). Further investigations into annealed austenitic stainless steels could provide insights into manipulating SRO and its effects on material properties. Atomistic simulations provided understanding of SRO behavior that was difficult to capture experimentally. This project created the first spin cluster expansion model that is able to capture and describe SRO effects in Fe-Ni-Cr FCC alloys, accounting for the non-negligible effects of magnetism. An automated computational workflow was established to provide reliable predictions of SRO in Fe-Ni-Cr austenitic alloys, both with and without the presence of H atoms. Analysis of the propensity for SRO in Fe-Ni-Cr alloys revealed that H tends to cluster with specific, well-defined SRO domains. The computational framework is general purpose and can be extended to realistic stainless steels across diverse composition ranges. With confidence that SRO is possible in austenitic stainless steels, we developed a discrete dislocation finite element code to understand the interaction of dislocations with SRO in the presence of H. By incorporating H effects on the dislocation emission and SRO stress field we show that the critical stress for the dislocation pileup to breakthrough the SRO domain decreases in the presence of H, which directly contributes localized deformation at the macroscale. Through the simulation of a uniaxial tension test, we demonstrated that H-induced weakening of SRO stress field and H-enhanced dislocation emission can lead to the onset of shear localization at lower macroscopic strains. As a whole, this project identified three novel alloys that show improvements in performance and cost efficiency for H-facing applications by studying correlations between alloy chemistry and deformation behavior. We also made significant advancements to experimental and computational methodologies necessary to study the chemistry and distribution of SRO across a range of alloys, which in turn allowed us to demonstrate how deformation mechanisms change due to the contributions of SRO in austenitic alloys in the presence of H. The combined advancements in fundamental understanding with novel alloy development in this project has increased the viability of next generation H-technologies for the broader public through accessible low-cost alloys and accelerated development towards future H-infrastructure.

08 HYDROGEN↗
NASA NTRSDate not supplied

Probing Sensitivity of Discharge Characteristics to Model Selection using Uncertainty Quantification in an aprotic Li-Oxygen Battery

Currently, there are several models in the literature, such as kinetic models, microstructural models, and mass transport models that describe a Li-air battery's discharge behavior. Many of these models are calibrated and tested at low current densities and cannot be easily transferred to high current densities. Even at low current densities, there is no quantitative method for a researcher to choose a reaction kinetic model such as classical Butler-Volmer and its derivatives, and modified Marcus-Hush-Chidsey, a resistance model for lithium peroxide such as electron transport via tunneling or linear resistivity, a surface coverage model (lithium peroxide growth) such as partial coverage or full coverage, and mass transport model (discussed in Ref. [1]). Also, it is time-consuming to test different models at high current density (1C) due to a lack of well-tested models and well-calibrated model parameters. For this presentation, we will develop an analytical model, which acts as a surrogate model for a sophisticated finite element model to predict discharge time and discharge voltage. Next, we use an uncertainty quantifying technique called reduced-order stochastic optimization [2, 3] to determine the uncertainty in model parameters for rate kinetics, lithium peroxide resistivity, and parasitic resistance. Finally, a finite element simulation is performed to determine the error introduced by the surrogate model and its influence on the uncertainty in the model parameters.

M Mehta↗
DOE OSTI2025

Design and Development of Novel Equiatomic Refractory Multi Principal elemental Alloys Based on MoNbTi System for Use in Irradiation Environments

Multi Principal Elemental Alloys (MPEA) have emerged as promising materials for next-generation nuclear reactors due to their exceptional irradiation resistance. Eight equiatomic MPEA based on the MoNbTi system, comprising of elements with low thermal neutron absorption cross-sections were explored using a combined approach employing empirical parameter estimations, and CALPHAD simulations by which the phases and elemental segregation observed in all the alloys in the as-cast state were predicted. Solution heat treatment at 1500°C transformed five alloys into single-phase matrix materials, enhancing homogeneity and reducing hardness. The densities of the alloys ranged between 6.47 to 7.68 g/cm3, hardness between 472 and 656 VHN, Young’s modulus between 142 GPa to 169 GPa, shear modulus between 54 GPa and 62 GPa, bulk modulus between 117 GPa to 194 GPa and Poisson’s ratio between 0.3 to 0.35. The in-situ high temperature Xray diffraction results, differential scanning calorimetry and dilatometry results up to 1000°C suggested the high temperature phase stability of the MPEA. Subsequent ageing heat treatment at 800 and 1000 oC for 96 hours revealed significant secondary phase precipitation in MoNbTiZr, MoNbTiZrV, and MoNbTiCrA. Oxidation studies at 800 oC for 24 hours in air revealed superior oxidation resistance and cubic rate law dependence in Cr containing MPEA especially in MoNbTiCrAl, while severe mass gain resulting in total disintegration and exfoliation in MoNbTiZr and MoNbTiZrV. This comprehensive study underscores the potential of novel MPEA as promising materials for advanced nuclear reactor applications, shedding light on their microstructural control, mechanical properties, thermal stability, and oxidation resistance.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Towards understanding particle rigid-body motion during solid-state sintering

A quantitative understanding of particle rigid body (RB) motion that inherently accompanies grain boundary (GB) diffusion is highly desirable to understand and control the dynamic interplay between coarsening and densification during solid state sintering. In this work, by computer simulation using a multi-phase-field approach, we analyze systematically the roles played by each of these processes at different stages of the shrinkage of the internal pore in a three-particle green body as a function of particle size as well as thermodynamic and kinetic factors of interfaces. We demonstrate that particle RB translation promotes both neck growth, and pore rounding and shrinkage. Moreover, the forces acting at GBs and pulling neighboring particles towards one another dynamically evolve as particles fuse. In contrast, particle RB rotation has no contribution to pore shrinkage. The translational force acting on an individual particle varies with not only its size, but also the number and sizes of its neighboring particles.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect of sintering temperature on adhesion of spray-on piezoelectric transducers

Conventionally sol-gel spray-on transducers require a high-temperature (> 700 ◦C) sintering process; however, this process can affect the microstructure of the substrate material. For mechanical elbows and valves utilized for fluid transport in the energy sector, the components are designed to have a specific microstructure, and deviations from these specifications can create weak points in the system. For this reason it is important to investigate how the temperature of the deposition process affects the substrate. This paper investigates the effect of high-temperature and low-temperature (< 150 ◦C) processing conditions on the surface composition of the substrate. Furthermore, the resultant transducers from high- and low-temperature fabrication processes are compared to determine if a low-temperature processing method is feasible. For these studies a sol-gel spray-on process is employed to deposit piezoelectric ceramics onto a stainless-steel 316L substrate. Energy-dispersive X-ray spectroscopy is utilized to determine the composition of the substrate surface before and after transducer deposition. Results indicate that the high-temperature processing conditions may alter the surface composition of the metal due to a diffusion of the metal into the ceramic, which results in a metal surface that is bonded to the ceramic. Furthermore, it is shown that low-temperature processing of spray-on transducers is a viable method for transducer fabrication where the resultant transducers meet the industry minimum requirement of 30 dB signalto-noise ratio. In parallel simulation calculations, finite-element method (FEM) studies were performed to model the adhesive strength of the low-temperature processed transducer to the substrate surface. Comparisons between the simulations and experiments suggest that the bond strength is much greater than the commercial gel bonds and closer to hardened epoxy glue bonds. These results indicate that spray-on transducers fabricated under lowtemperature processing conditions are a viable solution for leave-in-place monitoring of structures.

M. Sinding, Kyle↗
DOE OSTI2020

All-atom molecular dynamics simulations of weak polyionic brushes: influence of charge density on the properties of polyelectrolyte chains, brush-supported counterions, and water molecules

All atom molecular dynamics (MD) simulations of planar Na+-counterion-neutralized polyacrylic acid (PAA) brushes are performed for varying degrees of ionization (and thereby varying charge density) and varying grafting density. Variation in the PE charge density (or degree of ionization) and grafting density leads to massive changes of the properties of the PE molecules (quantified by the changes in the height and the mobility of the PE brushes) as well as the local arrangement and distribution of the brush-supported counterions and water molecules within the brushes. The effect on the counterions is manifested by the corresponding variation of the counterion mobility, counterion concentration, extent of counterion binding to the charged site of the PE brushes, water-in-salt-like structure formation, and counterion-water–oxygen radial distribution function within the PE brushes. On the other hand, the effect on water molecules is manifested by the corresponding variation of water–oxygen–water–oxygen RDF, local water density, water–water and water–PE functional group hydrogen bond networks, static dielectric constant of water molecules, orientational tetrahedral order parameter, and water mobility. Enforcing such varying degree of ionization of weak polyelectrolytes is possible by changing the pH of the surrounding medium. Thus, our results provide insights into the changes in microstructure (at the atomistic level) of weak polyionic brushes at varying pH. Finally, we anticipate that this knowledge will prove to be vital for the efficient design of several nano-scale systems employing PE brushes such as nanomechanical gates, current rectifiers, etc.

42 ENGINEERING↗
DOE OSTI2025

Multi-objective surrogate-assisted calibration of CPFEM models using macroscopic response and in situ EBSD measurements of grain reorientation trajectories

Crystal plasticity finite element method (CPFEM) models are widely used to simulate the deformation behaviour of polycrystalline materials, but their calibration is often limited by their high computational cost and the non-convexity of the optimisation landscape. Here, this study develops a multi-objective surrogate-assisted calibration workflow that couples a multi-objective genetic algorithm (MOGA) with an adaptively trained deep neural network (DNN) surrogate model to efficiently identify CPFEM parameters from experimental data. The workflow is demonstrated on three crystal plasticity (CP) formulations of increasing complexity — Voce hardening (VH), two-coefficient latent hardening (LH2), and six-coefficient latent hardening (LH6) — using in situ electron backscatter diffraction (EBSD) measurements of Alloy 617 under uniaxial tensile loading. The CPFEM models are calibrated against the experimentally observed stress–strain response and reorientation trajectories of eight grains, then validated against eight additional trajectories and overall texture evolution. Across the CP formulations, the macroscopic response was reproduced reliably, while differences emerged in the robustness and accuracy of the grain-scale predictions. Including grain reorientation trajectories in the multi-objective calibration improved texture evolution predictions and filtered out physically inconsistent parameter sets that can arise from calibrating against only the stress–strain data. The workflow also demonstrates good transferability of calibrated parameters from a low- to a high-fidelity microstructural model. These results provide practical guidance for integrating in situ microstructural data into CPFEM through efficient, repeatable, and physically meaningful multi-objective calibration.

Crystal plasticity finite element method↗
DOE OSTI2024

Comprehensive new insights on the potential use of SiC as plasma-facing materials in future fusion reactors

Abstract The performance of silicon carbide as an alternative plasma facing material (PFM) was studied at various irradiation conditions relevant to ion energies and fluxes of a fusion reactor. This analysis involves detailed modeling of subsurface plasma/material interactions, sputtered particle transport above the surface and redeposition, and related changes in material composition and microstructure induced by steady-state and Edge Localized Mode ion fluxes. Transition of a crystalline SiC surface to semi-crystalline and amorphous phases was analyzed based on advanced modeling of DIII-D tokamak experiments where SiC was irradiated in single- and multiple- L-mode and H-mode discharges. This analysis shows that displacement damage, particle deposition/redeposition, and D accumulation on the SiC divertor surface can lead to significant microstructural changes that result in enhanced sputtering erosion in comparison with the original crystalline material. However, the resulting total net erosion rate for a full-coverage, advanced tokamak, SiC coated divertor may well be acceptably low. Moreover, the C sputtering yield from the evolved SiC surface can be seven times lower than from a pure graphite surface; this would imply significantly reduced tritium co-deposition rates in a D-T tokamak reactor, compared with a pure carbon surface. It was also determined that chemical sputtering of both C and Si should not result in any noticeable effect on the net erosion, for attached plasma regimes. Our results thus show encouraging results overall for use of SiC as a PFM in tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Crystal plasticity finite element simulation of lattice rotation and x-ray diffraction during laser shock compression of tantalum

Here we present a crystal plasticity model tailored for high-pressure, high-strain-rate conditions that uses a multiscale treatment of dislocation-based slip kinetics. We use this model to analyze the pronounced plasticity-induced lattice rotations observed in shock-compressed polycrystalline tantalum via in situ x-ray diffraction. By making direct comparisons between experimentally measured and simulated texture evolution, we can explain how the details of the underlying slip kinetics control the degree of lattice rotation that ensues. Specifically, we show that only the highly nonlinear kinetics caused by dislocation nucleation can explain the magnitude of the rotation observed under shock compression. We demonstrate a good fit between our crystal plasticity model and x-ray diffraction data and exploit the data to quantify the dislocation nucleation rates that are otherwise poorly constrained by experiment in the dynamic compression regime.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Micromechanical Modeling of the Thermal Expansion of Graphite/copper Composites with Nonuniform Microstructure

Two micromechanical models were developed to investigate the thermal expansion of graphite/copper (Gr/Cu) composites. The models incorporate the effects of temperature-dependent material properties, matrix inelasticity, initial residual stresses due to processing history, and nonuniform fiber distribution. The first model is based on the multiple concentric cylinder geometry, with each cylinder treated as a two-phase composite with a characteristic fiber volume fractions. By altering the fiber volume fraction of the individual cylinders, unidirectional composites with radially nonuniform fiber distributions can be investigated using this model. The second model is based on the inelastic lamination theory. By varying the fiber content in the individual laminae, composites with nonuniform fiber distribution in the thickness direction can be investigated. In both models, the properties of the individual regions (cylinders or laminae) are calculated using the method of cells micromechanical model. Classical incremental plasticity theory is used to model the inelastic response of the copper matrix at the microlevel. The models were used to characterize the effects of nonuniform fiber distribution on the thermal expansion of Gr/Cu. These effects were compared to the effects of matrix plasticity, choice of stress-free temperature, and slight fiber misalignment. It was found that the radially nonuniform fiber distribution has little effect on the thermal expansion of Gr/Cu but could become significant for composites with large fiber-matrix transverse CTE and Young's modulus mismatch. The effect of nonuniform fiber distribution in the through-thickness direction of a laminate was more significant, but only approached that of the stress-free temperature for the most extreme cases that include large amounts of bending. Subsequent comparison with experimental thermal expansion data indicated the need for more accurate characterization of the graphite fiber thermomechanical properties. Correlation with cyclic data revealed the presence of a mechanism not considered in the developed models. The predicted response did, however, exhibit ratcheting behavior that has been observed experimentally in Gr/Cu. Finally, simulation of the actual fiber distribution of particular specimens had little effect on the predicted thermal expansion.

Bednarcyk, Brett A.↗
DOE OSTI2022

Calcium silicate hydrate colloid at different humidities: Microstructure, deformation mechanism, and mechanical properties

Calcium silicate hydrate (C-S-H) is the main hydration product of Portland cement, while fundamental questions persist regarding its colloidal structure and water content. In this work, we developed a full atomistic C-S-H colloid model and investigated the physical and mechanical properties at different gel water concentrations. Water confined in nanometer gel pores degrades the mechanical properties of C-S-H because of its hydrolysis effect. A “ductile to brittle” transition was observed in the C-S-H colloid model with increasing gel water contents, evolving from transgranular failure to intergranular fracture. The gel water confined in nanometer-sized pores displays glassy characteristics, and it acts as a lubricant and facilitates structure distortions during the deformation. We elucidated the topology effect of the hydrogen bond network on the evolution of the viscoelasticity of C-S-H at different humidities. In conclusion, this work sheds light on the role of water in C-S-H colloids from nanostructure perspectives.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hotspot formation due to shock-induced pore collapse in 1,3,5,7-tetranitro-1,3,5,7-tetrazoctane (HMX): Role of pore shape and shock strength in collapse mechanism and temperature

The shock to detonation transition in heterogeneous high energy density solids starts with the spatial localization of mechanical energy into so-called hotspots that form due to the interaction between the leading wave and microstructural features and defects. We used large-scale molecular dynamics to characterize the hotspots resulting from the shock-induced collapse of cylindrical voids and elongated cracks focusing on the effect of shock strength, defect shape, and size. The temperature fields resulting from the collapse of cracks elongated along the shock direction show significantly higher sensitivity to both shock strength and size than cylindrical voids. Cracks 80 nm in length result in temperatures almost three times higher than voids 80 nm in diameter, reaching values corresponding to the ideal case of isentropic recompression of a gas. The molecular dynamics trajectories reveal the atomic origin of this contrasting behavior. While circular voids undergo a transition from viscoelastic pore collapse to a hydrodynamic regime with increasing shock strength, shock focusing in elongated cracks results in jetting and vaporization which, upon recompression, leads to increased heating.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure‐Dependent Sodium Storage Mechanisms in Hard Carbon Anodes

Sustainable energy storage is essential to support the transition to renewables and meet the increasing demand for energy. Sodium‐ion batteries (NIBs) are attractive for grid‐scale energy storage due to the abundance and low cost of sodium, sustainability of other battery components, and electrochemical performance. Hard carbon (HC) is a leading anode material for NIBs, but its complex microstructure complicates the understanding of sodium storage mechanisms. Using X‐ray total scattering and density functional theory calculations, this study clarifies how HC's microstructural variations influence sodium storage across the slope (high potential) and plateau (low potential) regions of the potential capacity curve. In the slope region, sodium initially adsorbs at high‐binding energy defect sites and subsequently intercalates between graphene layers, adsorbing at low‐binding energy defect sites, correlating with different slopes observed during initial sodiation. Initial irreversibility arises from sodium trapping at surface defects and solid electrolyte interface formation. In the plateau region, sodium simultaneously intercalates and fills pores, influenced by pore size, interlayer spacing, and defect concentration. HCs with larger pore sizes form larger sodium clusters. In conclusion, the proposed mechanism underscores the role of microstructure engineering in enhancing HC performance and advancing NIBs for grid‐scale energy storage.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effects of Mineral Impurities and Heat on Uranium(VI) Sorption onto Bentonite (Final Report)

Most nuclear waste disposal options include compacted bentonite, consisting of montmorillonite clay, as part of a barrier system to minimize contaminant mobility. Uranium (U) is the primary element in spent nuclear fuel, and from an environmental perspective, a potential contaminant of water resources. Furthermore, uranium may control nuclear fuel degradation rates and the consequent release of other radioactive contaminants based on its diffusive transport away from waste canisters. Uranium sorption onto clay and other mineral surfaces is expected to limit U(VI) mobility in these systems. However, at this point a prediction of U(VI) sorption and transport behavior in performance assessment (PA) models is complicated by a series of factors, such as: (1) the presence of various U(VI) solution species with different charges and sorption characteristics; (2) the complex microstructure of montmorillonite clay resulting in two types of clay porosities and multiple sorption sites; (3) the largely unknown effects of bentonite mineral impurities on pore water chemistry, U(VI) sorption and diffusion behavior; and (4) the potential impacts of heat, generated by the decay of spent fuel, on mineralogical and microstructural transformations, and any subsequent effects on radionuclide sorption and mobility. In this project, we investigated the effects of calcite impurities on U(VI) sorption and diffusion onto montmorillonite before and after mineral exposure to heat. Overall, our main goals were to: 1. Gain a mechanistic understanding of the effects of calcite impurities on U(VI) sorption and diffusion in montmorillonite/bentonite at variable chemical conditions, and before and after mineral exposure to heat; and to 2. Work towards the development of new surface complexation and diffusion models to predict U(VI) sorption and mobility in montmorillonite/bentonite while accounting for the impacts of calcite impurities and heat. In order to achieve these goals, we pursued the following research objectives and tasks: 1. Characterize the effects of calcite impurities on U(VI) sorption onto Na-montmorillonite, and evaluate if and how these effects change due to solids’ exposure to heat (Task 1). 2. Characterize U(VI) surface speciation in solid samples from Task 1, with a particular focus on U(VI) precipitates and co-precipitates (Task 2). 3. Test the relevance of observed changes in U(VI) sorption characteristics for U(VI) diffusive transport behavior in bentonite barriers (Task 3). 4. Evaluate the exclusion of anionic U(VI) solution complexes from clay nanopores (Task 4). 5. Building on Tasks 1-4, start the development of new surface complexation and reactive transport models that can simulate and predict U(VI) sorption and diffusion in complex bentonite systems (Task 5). A detailed description of all tasks, and their specific results and conclusions is provided in this report.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Interpretation of wide-angle x-ray diffraction patterns from mesophase pitch-based carbon fibers – a simulation and experimental study

Carbon fiber is a critical material in a wide range of industries, where it is highly valued for its high specific strength/stiffness, excellent wear resistance, efficient electrical and thermal transport properties, chemical resistance, and low coefficient of thermal expansion. The properties of a specific carbon fiber are closely tied to its structural characteristics at all length scales. Here, in this work, we applied wide-angle x-ray diffraction to a set of heat-treated mesophase pitch-based carbon fibers, with the goal of elucidating the crystalline structures as a function of fiber orientation. To assist with analysis and interpretation of the experimental data, we employed diffraction pattern simulations using the scalar and vector forms of the Debye scattering equation to determine the influence of basal plane orientation, crystalline ordering (turbostratic-graphitic), and basal plane asymmetry on the diffraction patterns. The results presented here suggest that growth of the transverse crystallites in mesophase pitch-based carbon fiber is fixed until graphitization temperatures are reached. The work completed here provides a framework for the analysis of carbon fiber and other oriented carbon-based materials via diffraction.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Considerations for a TeV collider based on dielectric laser accelerators

Particle acceleration in dielectric microstructures powered by infrared lasers, or "dielectric laser acceleration" (DLA), is a promising area of advanced accelerator research with the potential to enable more affordable and higher-gradient accelerators for energy frontier science and a variety of other applications. DLA leverages well-established industrial fabrication capabilities and the commercial availability of tabletop lasers to reduce cost, with axial accelerating fields in the GV/m range. Further, desirable luminosities would be obtained by operating with very low charge per bunch but at extremely high repetition rates. And as a consequence of its unique operating parameter regime, coupling of the laser to the accelerator can potentially be in the 50% range and with low beamstrahlung energy loss due at the interaction point, making DLA a promising approach for a future multi-TeV linear collider.

43 PARTICLE ACCELERATORS↗