Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Elucidating the Effect of TiB{sub 2} Volume Percentage on the Mechanical Properties and Corrosion Behavior of Al5083-TiB{sub 2} Composites

Al5083-TiB{sub 2} in situ composites with 1, 3, and 5 volume percentages of TiB{sub 2} were fabricated. The effect of different volume percentages of TiB{sub 2} reinforcement particles on the mechanical properties and corrosion resistance of these composites was investigated. The hot extrusion process resulted in fragmentation and more homogeneous distribution of TiB{sub 2} particles throughout the Al5083 matrix. Also, the grain size reduced as the amount of TiB{sub 2} reinforcement particles increased which caused the improvement of both the strength and ductility of the material. It was shown that the hardness, the ultimate tensile strength (UTS), and the yield strength (YS) of both the as-cast and extruded materials increased with increasing TiB{sub 2} content. Also, TiB{sub 2} addition combined with the extrusion process improved both UTS and elongation (El.%) of the extruded structures which can be attributed to the presence of TiB{sub 2} particles and obtained microstructural refinement by hot extrusion process. However, the extruded Al5083-5 vol.% TiB{sub 2} composite showed lower ductility in comparison with the extruded Al5083-1 vol.% TiB{sub 2} and Al5083-3 vol.% TiB{sub 2} composites. Moreover, it could be concluded that the corrosion resistance and also the pitting corrosion behavior of the Al5083 alloy do not significantly change in the presence of TiB{sub 2} reinforcement particles.

36 MATERIALS SCIENCE↗

MODELS FOR ESTIMATING THE AUTOFRETTAGE PRESSURE AND RESIDUAL STRESSES IN WALLS OF TYPE 2 PRESSURE VESSELS

Autofrettage is a manufacturing process used during fabrication of Type 2 pressure vessels designed for usage at high pressures to enhance the fatigue life. The process locks high compressive residual stresses in the vessel’s liner wall that reduce the maximum and the mean stress during service loading. To achieve a consistent residual stress profile across the wall of the vessel, the choice of autofrettage pressure is critical. Several finite element analyses runs were conducted to estimate the correct autofrettage pressure that is a function of the yield strength of the liner material, the wall thickness, and the outside diameter of the liner for a wrap thickness of 17.06 mm (48 wire layers). From the finite element analyses results, models were developed to estimate the correct autofrettage pressure and the residual stress distribution across the liner wall as a function of the yield strength of the liner material, the wall thickness, and the outside diameter of the liner.

08 HYDROGEN↗

Low Temperature Regolith Bricks for In-Situ Structural Material

Current technology for producing in-situ structural materials on future missions to Mars or the moon relies heavily on energy-intensive sintering processes to produce solid bricks from regolith. This process requires heating the material up to temperatures in excess of 1000 C and results in solid regolith pieces with compressive strengths in the range of 14000 to 28000 psi, but are heavily dependent on the porosity of the final material and are brittle. This method is currently preferred over a low temperature cementation process to prevent consumption of precious water and other non-renewable materials. A high strength structural material with low energy requirements is still needed for future colonization of other planets. To fulfill these requirements, a nano-functionalization process has been developed to produce structural bricks from regolith simulant and shows promising mechanical strength results. Functionalization of granular silicate particles into alkoxides using a simple low temperature chemical process produces a high surface area zeolite particles that are held together via inter-particle oxygen bonding. Addition of water in the resulting zeolite particles produces a sol-gel reaction called "inorganic polymerization" which gives a strong solid material after a curing process at 60 C. The aqueous solution by-product of the reaction is currently being investigated for its reusability; an essential component of any ISRU technology. For this study, two batches of regolith bricks are synthesized from JSC-1A; the first batch from fresh solvents and chemicals, the second batch made from the water solution by-product of the first batch. This is done to determine the feasibility of recycling necessary components of the synthesis process, mainly water. Characterization including BET surface area, SEM, and EDS has been done on the regolith bricks as well as the constituent particles,. The specific surface area of 17.53 sq m/g (average) of the granular regolith material was obtained from nitrogen adsorption isotherm measurement. The size, shape and textures of regolith from SEM shows that the particles are 25-50 micrometers in size and mostly irregular in shape (Figure 1a). The elemental composition of regolith was identified from EDS analysis showed the presence of Si, Al, Fe, Na, Mg, Ca, Ti, O and C (see figure 1b). Each set of cylindrical brick samples were prepared by low energy process, and cured for 21 and 28 days, respectively to compare their compressive strength. Figure 1c, and d shows the JSC-1A brick and the compressive strength measurements. The results from the 21 day cured bricks (2 bricks) have been done and yielded an aver-age strength of 3050 psi, considerably higher than Portland cement mortars (Type IV and V). This promising technology provides the benefits of construction material similar to concrete, with a low complexity, low energy synthesis process and the likelihood of complete reusability of precious resources. Compressive strength using this method can be improved by increasing the surface area of the particles, using bi-modal particle size distribution, and adding certain additives to increase inter-particle forces.

ISRU↗

Microstructure and Mechanical Properties of Reaction-Formed Silicon Carbide (RFSC) Ceramics

The microstructure and mechanical properties of reaction-formed silicon carbide (RFSC) ceramics fabricated by silicon infiltration of porous carbon preforms are discussed. The morphological characterization of the carbon preforms indicates a very narrow pore size distribution. Measurements of the preform density by physical methods and by mercury porosimetry agree very well and indicate that virtually all of the porosity in the preforms is open to infiltrating liquids. The average room temperature flexural strength of the RFSC material with approximately 8 at.% free silicon is 369 +/- 28 MPa (53.5 +/- 4 ksi). The Weibull strength distribution data give a characteristic strength value of 381 MPa (55 ksi) and a Weibull modulus of 14.3. The residual silicon content is lower and the strengths are superior to those of most commercially available reaction-bonded silicon carbide materials.

Singh, M.↗

Enhanced Interfacial Strength in Carbon Fiber Composites via Mussel‐Inspired Sizing Polymers

Composite materials possess a high strength-to-weight ratio. A key determinant of their mechanical performance is the interfacial strength between the fibers and the matrix. Sizing agents are commonly used to improve this interface by promoting better adhesion, though optimizing this interaction remains a significant challenge. Here, this study evaluates the use of poly(catechol-styrene) (PCS), a mussel-inspired sizing agent, to enhance fiber–matrix bonding in carbon fiber composites. Woven carbon fiber laminates were dip-coated with varying concentrations of PCS (0.05 and 0.1 wt%) and subsequently fabricated using vacuum-assisted resin transfer molding followed by compression molding. Interlaminar shear strength (ILSS) tests showed improvements of 4% and 8% for the 0.05% and 0.1% PCS treatments, respectively. These results indicate that PCS is effective in reinforcing interfacial adhesion, thereby improving the mechanical integrity of carbon fiber-reinforced composites.

Carbon fiber composites↗

Advanced ceramic matrix composites for TPS

Recent advances in ceramic matrix composite (CMC) technology provide considerable opportunity for application to future aircraft thermal protection system (TPS), providing materials with higher temperature capability, lower weight, and higher strength and stiffness than traditional materials. The Thermal Protection Material Branch at NASA Ames Research Center has been making significant progress in the development, characterization, and entry simulation (arc-jet) testing of new CMC's. This protection gives a general overview of the Ames Thermal Protection Materials Branch research activities, followed by more detailed descriptions of recent advances in very-high temperature Zr and Hf based ceramics, high temperature, high strength SiC matrix composites, and some activities in polymer precursors and ceramic coating processing. The presentation closes with a brief comparison of maximum heat flux capabilities of advanced TPS materials.

Rasky, Daniel J.↗

Effect of Ultrasonic Treatment on The Tensile and Impact Properties of Thermoplastic Natural Rubber Nanocomposites Reinforced with Carbon Nanotubes

This study investigates the effect of ultrasonic treatment on the mechanical properties of thermoplastic natural rubber (TPNR) nanocomposites reinforced with multi-walled nanotubes. The TPNR nanocomposites were prepared using melt blending method from polypropylene (PP), natural rubber (NR) and liquid natural rubber (LNR) as a compatibilizer, respectively, with 1% of Multi-wall nanotubes. The nanocomposite was prepared using the indirect technique (IDT) with the optimum processing parameters at 180 deg. C with 80 rpm mixing speed and 11 minutes processing time. The results have showed that the good dispersion on nanotubes was achieved by ultrasonic treatment. The optimization of ultrasonic time indicated that the maximum tensile and impact properties occurred with 1 h ultrasonic treatment. The Young's modulus, tensile strength, elongation at break and impact strength have increased by almost 11%, 21%, 43% and 50%, respectively. The results from our study indicate that nanotubes have as excellent reinforcement filler in TPNR matrix.

36 MATERIALS SCIENCE↗

Trends in aerospace structures

Recent developments indicate that there may soon be a revolution in aerospace structures. Increases in allowable operational stress levels, utilization of high-strength, high-toughness materials, and new structural concepts will highlight this advancement. Improved titanium and aluminum alloys and high-modulus, high-strength advanced composites, with higher specific properties than aluminum and high-strength nickel alloys, are expected to be the principal materials. Significant advances in computer technology will cause major changes in the preliminary design cycle and permit solutions of otherwise too-complex interactive structural problems and thus the development of vehicles and components of higher performance. The energy crisis will have an impact on material costs and choices and will spur the development of more weight-efficient structures. There will also be significant spinoffs of aerospace structures technology, particularly in composites and design/analysis software.

Card, M. F.↗

Laboratory Foamed-Cement-Curing Evolution Using CT Scanning: Insights From Elevated-Pressure Generation

Computed-tomography (CT) scanning has become a mainstay among scientists (Wildenschild and Sheppard 2013) because it enables nondestructive observation of material processes and formation in real time. Foamed cement is a high-strength, low-density material containing nitrogen gas, and is used to stabilize wellbore casings both onshore and offshore. In-situ foamed cement is subject to pressure changes because the slurry is pumped downhole and cures at depth. To correlate the influence of pressure to the gas-void size and the curing evolution of a foamed cement, two laboratory foamed cements were generated and CT scanned as they cured. One cement was generated following the American Petroleum Institute (API) industry standard API RP 10B-4 (2015) at atmospheric conditions using a blender, and the other cement was created using a foamed-cement generator (FCG) (resembling that of de Rozières and Ferrière 1991) to produce a sample at an elevated pressure. FCG-generated cement qualities (in the range of 20, 25, 30, 35, and 40%) were scanned at their cured state for comparison. From the CT-image time series and the single FCG scans, the volumetric void properties were characterized and compared. The time-series blender voids were an order of magnitude larger than the FCG voids, and void growth was stagnant after a curing period of 100 minutes, whereas the FCG voids gradually increased in volume after 100 minutes. The Hsü-Nadai plots (Brandon 1995) reveal that the FCG and blender voids are weakly prolate, and all FCG voids, regardless of generation quality, relax to a greater final-magnitude strain than the blender voids. Furthermore, these findings confirm that both the void size and the curing process are influenced by the pressure at which a foamed cement is generated.

36 MATERIALS SCIENCE↗

Thermoelastic micromechanical stresses associated with a large alpha-silicon carbide grain in a polycrystalline beta-silicon carbide matrix

The thermoelastic micromechanical stresses associated with a single large hexagonal alpha-SiC grain within a fine-grain-size cubic (3C) beta-SiC matrix were calculated. The naturally occurring residual stresses which are created during cooling from the processing temperatures and the effects of superimposed applied external stresses are both considered. A significant effect of the shape or geometry of the alpha-SiC grain is revealed, with the largest residual stresses associated with the naturally occurring tabular or platelet structure. The stresses are compared with the published strength results for these materials, which suggests that the residual stresses assume a significant role in the strength reduction that is observed.

Li, Zhuang↗

Torsion Tests of Tubes

This report presents the results of tests of 63 chromium-molybdenum steel tubes and 102 17st aluminum-alloy tubes of various sizes and lengths made to study the dependence of the torsional strength on both the dimensions of the tube and the physical properties of the tube material. Three types of failure are found to be important for sizes of tubes frequently used in aircraft construction: (1) failure by plastic shear, in which the tube material reached its yield strength before the critical torque was reached; (2) failure by elastic two-lobe buckling, which depended only on the elastic properties of the tube material and the dimensions of the tube; and (3) failure by a combination of (1) and (2) that is, by buckling taking place after some yielding of the tube material.

Stang, Ambrose H↗

Strength of hot isostatically pressed and sintered reaction bonded silicon nitrides containing Y2O3

The hot isostatic pressing of reaction bonded Si3N4 containing Y2O3 produced specimens with greater room temperature strengths than those by high pressure nitrogen sintering of the same material. Average room temperature bend strengths for hot isostatically pressed reaction bonded silicon nitride and high pressure nitrogen sintered reaction bonded silicon nitride were 767 and 670 MPa, respectively. Values of 472 and 495 MPa were observed at 1370 C. For specimens of similar but lower Y2O3 content produced from Si3N4 powder using the same high pressure nitrogen sintering conditions, the room temperature strength was 664 MPa and the 1370 C strength was 402 MPa. The greater strengths of the reaction bonded silicon nitride materials in comparison to the sintered silicon nitride powder material are attributed to the combined effect of processing method and higher Y2O3 content.

William A Sanders↗

HYDROGEN-ASSISTED FRACTURE IN FORGED TYPE 304L AUSTENITIC STAINLESS STEEL

Austenitic stainless steels generally have good resistance to hydrogen-assisted fracture; however, structural designs for high-pressure gaseous hydrogen are constrained by the low strength of this class of material. Forging is used to increase the low strength of austenitic stainless steels, thus improving the efficiency of structural designs. Hydrogen-assisted racture, however, depends on microstructural details associated with manufacturing. In this study, hydrogen-assisted fracture of forged type 304L austenitic stainless steel is investigated. Microstructural variation in multi-step forged 304L was achieved by forging at different rates and temperatures, and by process annealing. High internal hydrogen content in forged type 304L austenitic stainless steel is achieved by thermal precharging in gaseous hydrogen and results in as much as 50% reduction of tensile ductility.

36 MATERIALS SCIENCE↗

Uncertainty Quantification and Management for Multi-scale Nuclear Materials Modeling

Understanding and improving microstructural mechanical stability in metals and alloys is central to the development of high strength and high ductility materials for cladding and cores structures in advanced fast reactors. Design and enhancement of radiation-induced damage tolerant alloys are facilitated by better understanding the connection of various unit processes to collective responses in a multiscale model chain, including: dislocation nucleation, absorption and desorption at interfaces; vacancy production, radiation-induced segregation of Cr and Ni at defect clusters (point defect sinks) in BCC Fe-Cr ferritic/martensitic steels; investigation of interaction of interstitials and vacancies with impurities (V, Nb, Ta, Mo, W, Al, Si, P, S); time evolution of swelling (cluster growth) phenomena of irradiated materials; and energetics and kinetics of dislocation bypass of defects formed by interstitial clustering and formation of prismatic loops, informing statistical models of continuum character with regard to processes of dislocation glide, vacancy agglomeration and swelling, climb and cross slip.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Materials Based on Solid Solutions of Bismuth Chalcogenides of n-Type Conductivity Prepared by Melt Crystallization in a Liquid

The microstructure, mechanical, and thermoelectric properties of samples of the n-type Bi{sub 2}Te{sub 3}–Bi{sub 2}Se{sub 3} solid-solution samples containing 6, 8, and 10 mol % Bi{sub 2}Se{sub 3}, doped with antimony iodide, cadmium chloride, and hexabromobenzene, are investigated. The samples are formed by hot pressing and the extrusion of granules prepared by melt crystallization in a liquid and ground in a mortar, cutting mill, and ball mill. Measurements are performed at room temperature and in the range of 100–600 K. The formation conditions and compositions of materials with an ultimate compressive strength of ~250 MPa and thermoelectric efficiency of (ZT){sub max} = (0.9–1.0) in the temperature range of 320–430 K are found.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Galactic and Solar Cosmic Ray Shielding in Deep Space

An analysis of the radiation hazards in support of NASA deep space exploration activities is presented. The emphasis is on materials required for radiation protection shielding. Aluminum has been found to be a poor shield material when dose equivalent is used with exposure limits for low Earth orbit (LEO) as a guide for shield requirements. Because the radiation issues are cost related-the parasitic shield mass has high launch costs, the use of aluminum as a basic construction material is clearly not cost-effective and alternate materials need to be developed. In this context, polyethylene is examined as a potentially useful material and demonstrates important advantages as an alternative to aluminum construction. Although polyethylene is useful as a shield material, it may not meet other design criteria (strength, stability, thermal); other polymer materials must be examined.

Wilson, John W.↗

Shape Memory Characteristics of Ti(sub 49.5)Ni(sub 25)Pd(sub 25)Sc(sub 0.5) High-Temperature Shape Memory Alloy After Severe Plastic Deformation

A Ti(49.5)Ni25Pd25Sc(0.5) high-temperature shape memory alloy is thermomechanically processed to obtain enhanced shape-memory characteristics: in particular, dimensional stability upon repeated thermal cycles under constant loads. This is accomplished using severe plastic deformation via equal channel angular extrusion (ECAE) and post-processing annealing heat treatments. The results of the thermomechanical experiments reveal that the processed materials display enhanced shape memory response, exhibiting higher recoverable transformation and reduced irrecoverable strain levels upon thermal cycling compared with the unprocessed material. This improvement is attributed to the increased strength and resistance of the material against defect generation upon phase transformation as a result of the microstructural refinement due to the ECAE process, as supported by the electron microscopy observations.

Atli, K. C.↗