SEARCH · Engineering Papers
Results for “impact analysis”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Impact of Glass Irradiation on Laser-Induced Breakdown Spectroscopy Data Analysis
Increased absorption of optical materials arising from exposure to ionizing radiation must be accounted for to accurately analyze laser-induced breakdown spectroscopy (LIBS) data retrieved from high-radiation environments. We evaluate this effect on two examples that mimic the diagnostics placed within novel nuclear reactor designs. The analysis is performed on LIBS data measured with 1% Xe gas in an ambient He environment and 1% Eu in a molten LiCl-KCl matrix, along with the measured optical absorption from the gamma- and neutron-irradiated low-OH fused silica and sapphire glasses. Significant changes in the number of laser shots required to reach a 3σ detection level are observed for the Eu data, increasing by two orders of magnitude after exposure to a 1.7 × 1017 n/cm2 neutron fluence. For all cases examined, the spectral dependence of absorption results in the introduction of systematic errors. Moreover, if lines from different spectral regions are used to create Boltzmann plots, this attenuation leads to statistically significant changes in the temperatures calculated from the Xe II lines and Eu II lines, lowering them from 8000 ± 610 K to 6900 ± 810 K and from 15,800 ± 400 K to 7200 ± 800 K, respectively, for exposure to the 1.7 × 1017 n/cm2 fluence. The temperature range required for a 95% confidence interval for the calculated temperature is also broadened. In the case of measuring the Xe spectrum, these effects may be mitigated using only the longer-wavelength spectral region, where radiation attenuation is relatively small, or through analysis using the iterative Saha–Boltzmann method.
Experimental stress analysis of large plastic deformations in a hollow sphere deformed by impact against a concrete block
An experimental plastic strain measurement system is presented for use on the surface of high velocity impact test models. The system was used on a hollow sphere tested in impact against a reinforced concrete block. True strains, deviatoric stresses, and true stresses were calculated from experimental measurements. The maximum strain measured in the model was small compared to the true failure strain obtained from static tensile tests of model material. This fact suggests that a much greater impact velocity would be required to cause failure of the model shell structure.
Near ground level sensing for spatial analysis of vegetation
Measured changes in vegetation indicate the dynamics of ecological processes and can identify the impacts from disturbances. Traditional methods of vegetation analysis tend to be slow because they are labor intensive; as a result, these methods are often confined to small local area measurements. Scientists need new algorithms and instruments that will allow them to efficiently study environmental dynamics across a range of different spatial scales. A new methodology that addresses this problem is presented. This methodology includes the acquisition, processing, and presentation of near ground level image data and its corresponding spatial characteristics. The systematic approach taken encompasses a feature extraction process, a supervised and unsupervised classification process, and a region labeling process yielding spatial information.
The Gaseous Content of the Universe at Zeta less than 1.6
Together with graduate student Hsiao-Wen Chen, I have measured and analyzed structural and morphological parameters of 38 galaxies in eight fields for which sensitive measurements of corresponding Ly(alpha) absorption toward background QSOs are available. These measurements are based on Wide Field Planetary Camera 2 (WFPC2) observations obtained with the Hubble Space Telescope (HST) and provide a first look at how the incidence and extent of tenuous gas around galaxies depends on galaxy luminosity, size, and morphological type and on geometry of the impact. The primary result of the analysis is that the amount of gas encountered along the line of sight depends on the galaxy impact parameter and B-band luminosity but does not depend strongly on the galaxy average surface brightness, disk-to-bulge ratio, or redshift. This result confirms and improves upon an anti-correlation between Ly(alpha) absorption equivalent width and galaxy impact parameter found previously. More importantly, this result provides the first quantitative means of relating statistics of faint galaxies to statistics of Ly(alpha) absorption systems. which we plan to exploit to constrain the luminosity function of galaxies beyond the realm of current surveys. Results have been submitted for publication and will greatly improve our statistical conclusions . Together with graduate student Noriaki Yahata. I have measured and classified spectral properties of over 1000 faint galaxies and stars obtained in our low-resolution spectroscopic survey. The goal of this project is two-fold: (1) to exhaustively characterize the spectral properties of all faint galaxies that comprise our current survey, and (2) to gain experience with our measurement and classification code. which ultimately will be used on a data base of 20,000 galaxies to be obtained with the Two-Degree Field (2df) spectrograph at the Anglo-Australian Telescope (AAT). The results will ultimately be used for many goals, but so far we have concentrated on using the results to make a binary classification of the galaxies (i.e. early type versus late type) and to then exploit the density-morphology relationship to obtain a crude density indicator. The primary result of the analysis is that the incidence and extent of tenuous gas around galaxies shows no strong preference for local galaxy environment, at least over the range of densities spanned by the current observations. Along similar lines, two instances of Ly(alpha) absorption lines that arise in groups or clusters were examined. Analysis demonstrates that some can produce corresponding absorption lines and that LY(alpha) absorption lines do not avoid a high-density environment. A new measure of the galaxy-absorber cross-correlation function defines the statistical criterion by which galaxies and absorber pairs are to be matched. I have identified a damped Ly(alpha) absorption system at redshift z equals approximately 0.16, the lowest redshift confirmed to date. The most important results of the analysis are learning that the metal abundances of the absorption system are less than 10 percent of the solar metal abundance and that the absorbing gas is not rotating with the galaxy disk.
Field Sensitivity Analysis of Turbulence Model Parameters for Flow Over a Wing
Reynolds-averaged-Navier-Stokes (RANS) turbulence models are a critical tool in computational-fluid-dynamics simulations of aerodynamic systems, but simulation results can be highly sensitive to RANS-model parameter choices. Sensitivity analysis can be used to quantify these impacts, and the objective of this study is to demonstrate field sensitivity analysis with respect to ten parameters in the 2003 Menter shear-stress-transport (SST) turbulence model. Here, the analysis is demonstrated for an application relevant to wind energy, namely, flow over a NACA 0015 wing at 12 degree angle of attack and a Reynolds number of 1.5 x 10 6 . We quantify sensitivity using Sobol indices and the mean-squared gradient, which are estimated using polynomial chaos and active subspace models, respectively. Our results indicate that there are substantial spatial variations in parameter sensitivities, with different sets of most-sensitive parameters near the wing, as well as in the downstream wake, consistent with the physical interpretations of the turbulence model inputs. We show that, for this particular turbulence model and flow, simultaneous dimension reduction is possible across all quantities of interest, enabling efficient exploration of model outcomes. Ultimately, this analysis provides new insights into turbulence model parameter sensitivities in incompressible flows, and also demonstrates the implementation of field sensitivity analysis for applications relevant to aerodynamics simulations.
Robust Bonding Through Process Control
Process control has been proven to be the most reliable means of safeguarding the quality of adhesive bonds according to Federal Aviation Administration (FAA). A method for implementing process control for reduction in risk in a bonded joint fabrication process is demonstrated in this study using a selected bonding system. The stepwise method included risk analysis to identify defects with the highest impact and likelihood to occur, evaluation of various pre-bond surface analysis tools to monitor for the selected defects, and demonstration of the benefits of in-process monitoring utilizing threshold limits determined from bond performance tests. The bonded system selected for investigation was an aerospace carbon fiber epoxy composite substrate surface prepared with random orbital sanding using 180 grit aluminum oxide sand paper. A series of portable, pre-bond surface analysis tools were investigated for their ability to be used for in-line bond process control. Results and threshold limits are presented from roughness, ballistic water contact angle (WCA), color, gloss, and Fourier transform infrared spectroscopy (FTIR) surface analysis tools. Results demonstrated how in-process inspection methods can be used to ensure quality of a surface preparation for a selected bonding system. A framework is provided for implementation of bond process control for robust bonding.
Global NWP Impacts of Infrared Sounders from Geostationary Orbit
The Geostationary eXtended Observations (GeoXO) program, expected to launch in the 2030s, includes a proposed infrared (IR) sounder that would provide persistent atmospheric profile observations over much of the western hemisphere. In preparation, the National Aeronautics and Space Administration (NASA) Global Modeling and Assimilation Office (GMAO) observing system simulation experiment (OSSE) framework was used to assess the impact of such an instrument on global numerical weather prediction (NWP) as part of a global “ring” of such instruments. Building on previous preliminary studies, an evaluation of the impact of geostationary IR sounders will be presented with foci on the analysis, forecasts, and the forecast sensitivity observation impact (FSOI) metric, including an examination of the consequences for tropical cyclone representation. Overall, assimilation of geostationary IR provide a beneficial impact for NWP applications.
A Study of Layered Structural Configurations as Thermal and Impact Shielding of Lunar Habitats
The focus of this study is the analysis of a proposed multilayer material configuration as lunar habitat shielding so as to assess its ability to resist temperature extremes and impact. In order to resist this environmental hazard, the analysis will compare various configurations of potential shielding layers using both in-situ resource utilization (ISRU) and Earth-based materials. The technology for implementation of in-situ resources in construction is developing, though not yet able to produce a functional lunar habitat. As the lunar infrastructure is developed, ISRU techniques for manufacturing and construction may become more viable. Therefore, both types of materials are considered due to potential for application towards both near-term and long-term commencements of habitat construction. The thermal analysis in this paper utilizes the nonlinear heat equation to produce a depth-dependent temperature gradient from the habitat exterior to the interior that changes continuously with time during the lunar diurnal cycle. Static loading conditions meant to simulate the impact force of a 77.9 g meteorite were used to analyze the ability of a proposed multilayer shielding configuration to resist impact. A thermal stress analysis was performed to observe the effects of heat transfer through the proposed multilayer configuration. The results of this study should be useful in determining the potential for implementation of efficient shielding layers for the initial lunar base.
Power System Recovery from Momentary Cessation with Transient Stability Improvement
Power system dynamics will be significantly changed by integrating wind farms and solar photovoltaic plants into power systems. This study investigates the effect of momentary cessation of inverter-based resources (IBRs) on transient stability and provides a recovery strategy for bulk IBRs in power systems. The theoretical analysis was initially carried out on a one-machine infinite-bus system, demonstrating the IBR impact in a critical group. The analysis was then expanded to a multimachine power system with IBRs using the single-machine equivalent method. The study found that IBRs in critical and noncritical groups exert contrasting effects on transient stability. Finally, a strategy for enhancing transient stability is proposed by controlling IBRs during power system recovery. The proposed strategy was verified by simulation on IEEE 9-bus and IEEE 39-bus power systems with the addition of IBRs. A 39-bus power system simulation demonstrates the scalability of the proposed method. Here, the proposed strategy provides effective and executable measures for improving system security in the presence of IBRs.
Anchoring Strategies for Marine Renewable Energy at the Sandia Water Impact Facility
This report documents the formulation and preliminary analysis of potential anchoring strategies for use in future WEC testing at the Sandia Water Impact Facility given the existing 5-ton and 10-ton concrete blocks at the facility. Three anchoring strategies are created that are applicable to different mooring configurations for existing WECs of interest for testing. The three anchoring strategies have a maximum allowable load of between 24.57 kN and 281.17 kN, depending on whether the 5-ton or 10-ton blocks are used, with Strategy 3 with 10-ton blocks having the highest allowable load. The AquaHarmonics and CalWave xWave WECs can be tested up to a 1:1.5 and 1:1.15 scale, respectively, while maintaining a mooring configuration very close to the one used in ocean deployment. The requirements for the mooring lines, shackles, and triplates needed to support the three strategies are also calculated, with commercially available products specified. Finally, the padeyes connected to the existing concrete blocks are assessed and determined to be satisfactory for the loading expected with these anchoring strategies.
Southern Idaho Ecological Conservation: Investigating the Impact of Targeted Grazing to Improve Wetland Habitat in the Sterling Wildlife Management Area
Wetland ecosystems are vital for biodiversity conservation and ecosystem services. The Sterling Wildlife Management Area in Bingham County, Idaho, has management concerns about decadent and accumulated vegetation growth encroaching on wetland habitat, which presents challenges for wildlife, decreases biodiversity, and limits public access. Targeted grazing has been proposed as a sustainable alternative to chemical herbicides or burning. Land managers introduced targeted cattle grazing in January 2021 to reduce biomass. NASA DEVELOP partnered with the Idaho Department of Fish and Game to determine the impact of grazing using NASA Earth observations from Landsat 8 Operational Land Imager (OLI) in Google Earth Engine (GEE). Images were processed with TerrSet’s Land Change Modeler and ArcGIS Pro’s Change Detection Wizard to understand land changes following grazing. A Normalized Difference Vegetation Index (NDVI) analysis was performed to assess impacts on vegetation productivity and compare variance in biomass before and after grazing. A Normalized Difference Water Index (NDWI) was used to compare changes in the wetland and its vegetation content to evaluate the suitability of the area for migratory birds post-grazing. Results showed a decrease in the vegetation index and an increase in the water index postgrazing. The DEVELOP team’s analysis suggests that grazing helps break down thick, senesced vegetation and increase soil moisture. Providing a workflow model will aid partners in continuing to monitor this management area and other management areas across the state.
Relationship between phase difference and coefficient of restitution during low velocity foreign object transverse damage of composite plates
This work discusses a model to correlate the coefficient of restitution of low velocity transverse impacts of graphite-epoxy laminates with the residual deformation or central deflection at the end of the impact event. It is assumed that the energy absorbed by the target can be calibrated in terms of residual deflection, and thereby in terms of phase difference between the occurrence of impact force and central deflection to their maximas. Analysis was modeled on the basis of the experience from impact tests. Predictions are compared with the test results of impacted circular and flat plates. Experimentally measured values of coefficient of restitution and phase difference agreed well with the predicted relationship between them.
Renormalization group improved photon impact factors and the high energy virtual photon scattering
We perform the renormalization group improved collinear resummation of the photon-gluon impact factors. We construct the resummed cross section for virtual photon-photon (γ ∗ γ ∗ ) scattering which incorporates the impact factors and BFKL gluon Green’s function up to the next-to-leading logarithmic accuracy in energy. The impact factors include important kinematical effects which are responsible for the most singular poles in Mellin space at next-to-leading order. Further conditions on the resummed cross section are obtained by requiring the consistency with the collinear limits. Our analysis is consistent with previous impact factor calculations at NLO, apart from a new term proportional to C F that we find for the longitudinal polarization. Finally, we use the resummed cross section to compare with the LEP data on the γ ∗ γ ∗ cross section and with previous calculations. The resummed result is lower than the leading logarithmic approximation but higher than the pure next-to-leading one, and is consistent with the experimental data.
Comparison of Exploration Oxygen Recovery Technology Options Using ESM and LSMAC
In preparation for long duration manned space flight, numerous technology development efforts are ongoing in the area of environmental control and life support (ECLS). In cooperation with international, industry, and academic partners, NASA seeks to leverage the International Space Station as a testbed for technologies targeted for Exploration-class missions. In recent years, Equivalent Systems Mass (ESM) analyses have been conducted to evaluate the relative breakeven points and to compare technologies as part of ECLS architectural trades. While these studies have provided important data pertaining to key engineering metrics, additional considerations are important to more fully understand the potential impacts and costs associated with selecting a specific architecture. A tool, called the Life Support Multi-Dimensional Assessment Criteria (LSMAC), was recently proposed by Sierra Nevada Corporation in an attempt to incorporate influences of these additional considerations including Maintainability, Risk Analysis, Technology Readiness Level, Radiation Impacts, Manufacturing Costs, Reliability, Human Factors, and Un-Crewed Operations. As a first step toward evaluating and implementing this tool, LSMAC was used to revisit the ISS oxygen recovery trade from the 1990’s wherein Sabatier was selected over Bosch technology. Second, the tool was used to compare oxygen recovery developmental technologies currently in work. The results of these studies as well as a comparison with standalone ESM analyses are reported. Further, a discussion of the potential application of the tool across the ECLS portfolio and its potential use in future technology selection for ISS flight demonstrations is provided.
Systems Analysis and Optimization of Circular PET Packaging Supply Chains in the United States: Environmental and Socioeconomic Impacts
Many actions are underway at global, national, and local levels to address the plastic waste problem and transition toward a circular economy of plastics. Studies evaluating environmental and socioeconomic impacts of such a transition are lacking. Here, the purpose of this study is to conduct a national systems analysis of polyethylene terephthalate (PET) packaging supply chains in the United States. Material flow data was combined with environmental and socioeconomic indicators to evaluate and compare the sustainability of the linear PET packaging supply chain, current (2019) supply chain, and possible future circular supply chain options in the United States. Environmentally optimal circular US PET packaging material flows showed 31% and 38% savings of GHG emissions and energy demand, respectively, with a circularity of 77% when compared with a linear supply chain. Additionally, the environmentally optimal system showed higher employment (29%) and wages (31%) than a linear system, but with a 5% decrease in revenue generation. A socioeconomically optimal circular PET supply chain showed increased employment (by 52%), wages (by 67%), and revenues (by 1%), with a circularity of 59% when compared with the linear system. However, it showed 14% higher GHG emissions than a linear system, indicating a trade-off between environmentally and socioeconomically optimal circular PET packaging systems. Overall, linear-to-circular material flow transition may not necessarily lead to increased revenues and decreased environmental impacts of the entire system, but it does benefit society due to increased employment and wages. Future systems analysis work should focus on improving data quality for environmental and socioeconomic dimensions.
Assimilation of Aerosol Observations in the NASA GEOS Model
In the GEOS near real-time system, as well as in MERRA-2 which is the latest reanalysis produced at NASA's Global Modeling Assimilation Office (GMAO), the assimilation of aerosol observations is performed by means of a so-called analysis splitting method. The prognostic model is based on the GEOS model radiatively coupled to GOCART aerosol module and includes assimilation of bias-corrected Aerosol Optical Depth (AOD) at 550 nm from various space-based remote sensing platforms. In line with the transition of the GEOS meteorological data assimilation system to a hybrid Ensemble-Variational formulation, we are updating the aerosol component of our assimilation system to a variational ensemble type of scheme. In this talk we will examine the impact of replacing the current analysis splitting scheme with this new approach. Starting with the assimilation of satellite based single-channel retrievals; we will discuss the impact of this aerosol data assimilation technique on the 3D aerosol distributions by means of innovation statistics and verification against independent datasets such as the Aerosol Robotic Network (AERONET) and surface PM2.5. We will also present preliminary results related to the introduction of new aerosol data types in GEOS, including multi-spectral AOD retrievals.